vrizrakOriginal postBoston · Nov 21, 2014#1I've got 2007 Yaris with 91,000 ml. I had a vibration in D (it's Auto). No check engine light or error codes. So cleaned TB and MAF. I'm not sure if that noise was before but I definitely start noticing now. It sounds like something lose or just spinning inside. Is this normal? I uploaded short video on youtube. Please see on 45 sec.
https://www.youtube.com/watch?v=GF3IxKL9m1I Please advise.
Replies 21
CoryMWhite Rock BC · Nov 21, 2014#2It's pretty hard to tell much from that video. The mic seems to be picking up normal noises and making them sound worse than they are. It's normal to have some minor tick tick tick noises from the valves and injectors, but if you are getting knocking noises it's probably not good. If the noise is a metallic scraping noise, you may want to remove your drive belt and check. If the noise is gone, it's probably the waterpump impeller (usually they leak coolant prior to being that bad though).
If you can't get anywhere, try taking another video a little further away and I will listen again.
Cheers.
IllusionXBrossard, QC · Nov 21, 2014#3Sounds normal to me.
vrizrakThread starterBoston · Nov 21, 2014#4 Originally Posted by
CoryM ↑ It's pretty hard to tell much from that video. The mic seems to be picking up normal noises and making them sound worse than they are. It's normal to have some minor tick tick tick noises from the valves and injectors, but if you are getting knocking noises it's probably not good. If the noise is a metallic scraping noise, you may want to remove your drive belt and check. If the noise is gone, it's probably the waterpump impeller (usually they leak coolant prior to being that bad though).
If you can't get anywhere, try taking another video a little further away and I will listen again.
Cheers.
I will try to get another video on different phone. I think I heard metallic noise. How can check if it waterpump? I'm not sure if I understand correctly. Remove drive belt and run engine to see if noise comes up?
Thanks!
vrizrakThread starterBoston · Nov 22, 2014#5catalinRo · Nov 22, 2014#6The same noise I've noticed that yaris was making but after a couple of days the sound had suddenly disappeared
Betriventedmonton · Nov 22, 2014#7I hear something around 0:15 in the video.. and you say it's in drive while you're taking this video?
vrizrakThread starterBoston · Nov 22, 2014#8 Originally Posted by
Betrivent ↑ I hear something around 0:15 in the video.. and you say it's in drive while you're taking this video?
No that was in "P" on idle. In drive a had a vibration. Looks like vibration is gone after I cleaned TB and MAF.
IllusionXBrossard, QC · Nov 22, 2014#9Again... Sounds normal to me.
ex-x-fireSheboygan Falls, Wi. · Nov 22, 2014#10Take a long screwdriver (or even a wooden dowel) & place it at the accessories & the other part to your ear. The sound should transmit loudly on the noisy part. Or Remove the belt & feel for loose wobbly pulleys.
vrizrakThread starterBoston · Nov 24, 2014#11 Originally Posted by
ex-x-fire ↑ Take a long screwdriver (or even a wooden dowel) & place it at the accessories & the other part to your ear. The sound should transmit loudly on the noisy part. Or Remove the belt & feel for loose wobbly pulleys.
Removed belt. Not sure but looks like water pump's pulley little bit loose. Ran engine without belt and noise was gone. Nothing. Just clean engine sound. Turns out that was water pump. I'm planning to replace it this weekend. Will update after..
bronsinnj · Nov 24, 2014#12Excellent!
But the WP wasn't leaking?
How much was the wobble in the pulley? Did the rim of the pulley move more than like 1/8 inch?
tmontagueCaledonia Ont. · Nov 24, 2014#13my fiancee's wp went without leaking any fluid. The only way I knew was by a brutal noise. Most leak fluid first but not always, good advice to run without belt.
vrizrakThread starterBoston · Nov 24, 2014#14 Originally Posted by
bronsin ↑ Excellent!
But the WP wasn't leaking?
How much was the wobble in the pulley? Did the rim of the pulley move more than like 1/8 inch?
There is no leaks. Well at least I can't find it. When I tried to move pulley I can feel a little knocking. Not very hard knocking but still and the pulley is moving not bad but enough to feel it. I checked other pulley from Alternator and AC they standing still.
vrizrakThread starterBoston · Nov 24, 2014#15 Originally Posted by
tmontague ↑ my fiancee's wp went without leaking any fluid. The only way I knew was by a brutal noise. Most leak fluid first but not always, good advice to run without belt.
No noise without belt... :)
CoryMWhite Rock BC · Nov 24, 2014#16Glad you got it figured out. The water pump pulley should not rock at all. Some will slide in and out a SMALL amount (barely noticeable), but never rock. The bearing on the Yaris waterpump are a little weak so do not over tighten the belt when you replace the pump or you will be doing it again.
Cheers.
vrizrakThread starterBoston · Nov 24, 2014#17 Originally Posted by
CoryM ↑ Glad you got it figured out. The water pump pulley should not rock at all. Some will slide in and out a SMALL amount (barely noticeable), but never rock. The bearing on the Yaris waterpump are a little weak so do not over tighten the belt when you replace the pump or you will be doing it again.
Cheers.
I've notice belt was over tighten. That probably what kill bearing. Well I will find out when I pull it from the car. Thanks.
vrizrakThread starterBoston · Dec 2, 2014#18Last weekend took water pump out for replace. It actually wasn't leaking but as you can see on picture it something. And it wasn't spinning freely. Feels like it ran over rubber or something. Anyway changed WP and not noise is gone. Except belt is squeaking when cold. :)
harda toenailSE Missouri · Dec 4, 2014#19Ive got this noise. Did you have to drop the engine to get the pump out?
vrizrakThread starterBoston · Dec 5, 2014#20 Originally Posted by
harda toenail ↑ Ive got this noise. Did you have to drop the engine to get the pump out?
Yes. Thanks to Kou on his DYI.
DIY waterpump RnR First I've put car on jack stands. There is 2 bolts and 1 nut. The nut is right under engine mount. You will need a long extender with 14mm socket. So remove nut first. Then place your floor jack and pump it until it hold engine a little bit. Then remove 2 bolts from the top. Also 14mm.
CTScottUSA, CT · Dec 5, 2014#21You can actually replace the water pump without removing the engine mount. Remove the screw that mounts the AC pipe holder and slide the holder towards the front of the car. Once you do that you have room to remove the pulley and then the pump itself.
harda toenailSE Missouri · Dec 6, 2014#22Thank you scott, I'll try to go that route. I loosened my belt and the noise went away but I know the bearing is probably damaged. If a warm day comes around I'll swap it out.