Yarisworld Archive

DIY waterpump RnR

86 posts · 72,615 views · page 1 of 2

kouOriginal postnj · Jan 12, 2009#1
this was from before the hack just thought i would put it up again.
1.let the car cool down.
2.disconnect battery.
3.disconnect plug and wire from alternator,lossen two bolts on alternator so you can remove belt.
4.remove 10mm bolt from bracket holding ac hose and slide bracket back.
5.remove two bolts from alternator and take it out of the car.
6.remove waterpump pulley three 10mm bolts and remove pulley from car.
7.remove the bolts from the waterpump.
8.get a jack with a some wood to support the motor as you will need to remove the bolts from the side mount and drop the motor to remove the waterpump from the car.
9.put new waterpump on and do all this in reverse.
10.fill up coolant.
pics 064.JPGpics 066.JPGpics 067.JPGpics 068.JPGpics 069.JPGpics 071.JPGpics 072.JPGpics 073.JPG

Replies 85

CB900F2Toronto · Jan 12, 2009#2
Great post... How many miles/km on the car when the pump went?
PetersRedYarisThe Black Hills of South Dakota · Jan 12, 2009#3
On Scionlife I have read about quite a few water pumps failing early. Same motor, same pump? Probably just a freak thing...

Edit- Well what do you know, 59,000 miles and my pump has some crust below the weep hole. These water pump failures seem to getting more and more common.
kouThread starternj · Jan 12, 2009#4
Originally Posted by CB900F2 ↑
Great post... How many miles/km on the car when the pump went?
only 15,000 miles but i think it was my fault for tighetening the belt to much when installing NST pulley set.
ztrack157Biggs, CA · Jan 24, 2009#5
You have coolant all over the place. I just took my hood off because I was fiddling around with something and sure enough I have coolant on the under side of the hood. I have nowhere the amount you did and there was none on the pulley or in the vicinity. Either way the bitch is being changed out next week.
CB900F2Toronto · Jan 24, 2009#6
ztrack.. Did you also install a NST pulley and possibly over tighten the pulley belt?


Originally Posted by ztrack157 ↑
You have coolant all over the place. I just took my hood off because I was fiddling around with something and sure enough I have coolant on the under side of the hood. I have nowhere the amount you did and there was none on the pulley or in the vicinity. Either way the bitch is being changed out next week.
PetersRedYarisThe Black Hills of South Dakota · Jan 24, 2009#7
What's the deal with water pumps failing on NST pulley equiped engines? I don't think mine was affected by the pulley as the WP bearing noise started just a few miles post the NST installation and the antifreeze "crust" looked like it had been there awhile, though I didn't see it when installing the pulley.

My belts are definitely not to tight as I like them on the loose side. So long as they don't squeel, they're tight enough.
kouThread starternj · Jan 24, 2009#8
i think mine was bad before the nst pulleys.maybe just the way the belt is tensioned from the factory.
ztrack157Biggs, CA · Jan 24, 2009#9
I have NST as well. And in the last 2,000 miles I heard a noise I knew shouldn't be coming from the engine bay. It was the water pump. I don't know what is considered to tight I can still wiggle the belt. And I had thought it was to tight so i loosened it slightly and then spun the belt so it wasn't to tight after installation.
auxmikeLI, New Yawk · Jan 24, 2009#10
THe pump's not covered by the warr. guys?
Why did'nt you just let the dealer shoulder the labor/cost?
Don't you get 5/60,000 on the drivetrain???
ztrack157Biggs, CA · Jan 24, 2009#11
Yes we have that but with NSt they can say we over tightened the belt. Thus no warranty.
BLAZINBLUEVITZNEW YORK · Jan 24, 2009#12
this problem isn't specific to nst equipped cars so don't start assuming its gonna happen to you if you have or are gonna buy. my buddy who's a toyota mechanic says water pumps and yari are starting to become a regular thing at his shop.....
nemelekArizona · Jan 24, 2009#13
How much does a water pump cost? Did you get from Toyota or some place else like Auto Zone or NAPA?
auxmikeLI, New Yawk · Jan 24, 2009#14
Originally Posted by BLAZINBLUEVITZ ↑
my buddy who's a toyota mechanic says water pumps and yari are starting to become a regular thing at his shop.....
Wonderful.😠
Did he give you any idea on about what milage the pumps go?
That's unacceptable, especially for a make like Toyota, supposedly "the best".
Thanks for the heads up, BTW.
Now I gotta start watching a waterpump on a brand freakin' new car........
auxmikeLI, New Yawk · Jan 24, 2009#15
Originally Posted by nemelek ↑
How much does a water pump cost? Did you get from Toyota or some place else like Auto Zone or NAPA?
The Genuine dealer water pump MSRP is about $100USD. I've seen it OEM on the net for $75USD.
Pump includes parts #8 & #9 in the sketch below.
Hope this helps.....
F804030.gif
PetersRedYarisThe Black Hills of South Dakota · Jan 24, 2009#16
Originally Posted by BLAZINBLUEVITZ ↑
this problem isn't specific to nst equipped cars so don't start assuming its gonna happen to you if you have or are gonna buy. my buddy who's a toyota mechanic says water pumps and yari are starting to become a regular thing at his shop.....
I agree, it's just kinda funny that most of us have an NST pulley installed.
PetersRedYarisThe Black Hills of South Dakota · Jan 24, 2009#17
Originally Posted by auxmike ↑
The Genuine dealer water pump MSRP is about $100USD. I've seen it OEM on the net for $75USD.
Pump includes parts #8 & #9 in the sketch below.
Go to Sparks Toyota-

http://trdsparks.com/index.php

$53 for the OEM pump and gasket...
auxmikeLI, New Yawk · Jan 24, 2009#18
Originally Posted by ztrack157 ↑
I have NST as well. And in the last 2,000 miles I heard a noise I knew shouldn't be coming from the engine bay. It was the water pump. I don't know what is considered to tight I can still wiggle the belt. And I had thought it was to tight so i loosened it slightly and then spun the belt so it wasn't to tight after installation.
Are you guys running the TRD rad caps too?
Perhaps too much pressure for the pumps seals?
Hope the Yaris does'nt turn out to be a Japanese Yugo.....
Yugo_Ad.jpg
CB900F2Toronto · Jan 24, 2009#20
A belt tension gauge should be used to check the tension on the belt and to insure it is with in spec...


Originally Posted by ztrack157 ↑
I have NST as well. And in the last 2,000 miles I heard a noise I knew shouldn't be coming from the engine bay. It was the water pump. I don't know what is considered to tight I can still wiggle the belt. And I had thought it was to tight so i loosened it slightly and then spun the belt so it wasn't to tight after installation.
ShroomsterOrlando · Jan 25, 2009#21
Originally Posted by CB900F2 ↑
A belt tension gauge should be used to check the tension on the belt and to insure it is with in spec...
yeah well easier than going out and buying a belt tensioner gauge is to just 'eyeball' the deflection.....

where the belt is stretched between the farthest pulleys, push down on it it shouldn't move maybe 1/2" to 3/4" down ---any more and add tension......
ztrack157Biggs, CA · Jan 25, 2009#22
My pump was $68. There are about $55 otherwise from Kragen/Schucks?checker or whatever the hell they are in your area. Mine is OEM replacement. The others are Cardone.
CB900F2Toronto · Jan 18, 2010#24
Peter.. Did you ever change out your water pump??...

Originally Posted by PetersRedYaris ↑
On Scionlife I have read about quite a few water pumps failing early. Same motor, same pump? Probably just a freak thing...

Edit- Well what do you know, 59,000 miles and my pump has some crust below the weep hole. These water pump failures seem to getting more and more common.
YarisSedanCalifornia - Bay Area · Jan 18, 2010#25
My water pump has gone out twice already i have 23k miles.
GeneralDon7Frederick, MD · Feb 4, 2010#26
The dealer actually notified me that mine was leaking when I went in to do that Seat belt tensioner recall. They covered it then (40,000 mi), not sure if i would be now(71000 mi).
127.0.0.1NE · Feb 4, 2010#27
Originally Posted by Shroomster ↑
yeah well easier than going out and buying a belt tensioner gauge is to just 'eyeball' the deflection.....

where the belt is stretched between the farthest pulleys, push down on it it shouldn't move maybe 1/2" to 3/4" down ---any more and add tension......

'easier' is not necessarily correct. same with bolt torque.

if you do not have the correct tools,
you have no business in the engine compartment

(not -you-, I mean anyone)

anyhow, water pumps do fail and they are easy to replace. they should last >180,000 though
AothachosLong Island, NY · Feb 4, 2010#28
Originally Posted by Shroomster ↑
yeah well easier than going out and buying a belt tensioner gauge is to just 'eyeball' the deflection.....

where the belt is stretched between the farthest pulleys, push down on it it shouldn't move maybe 1/2" to 3/4" down ---any more and add tension......
Someone told me if you can turn your belt to the side with one finger, its tight enough, so thats what I have been doing, I might have to tighten it a littttttle bit just a little because it has been squeaking bad on cold starts only when it warms up its find.


and my water pump hasn't had any problems yet, i have 50,000 miles on my car with the whole nst pulley setup (10 % underdrive crank, wp, alt.)
bankrobberCentral Florida · Feb 4, 2010#29
I have 81,000 miles and everything is stock on engine. Not had a problem with water pump yet.
fmicleSan Jose, CA, USA · Feb 4, 2010#30
Originally Posted by PetersRedYaris ↑
Haha, Sucks to be you. The Xb water pump is only $53.87, I assumed them to be the same. I see no reason why they would be different, same motor and the pulley must be transfered...

http://www.trademotion.com/partlocat...05&catalogid=1
It's exactly the same price as the Yaris one 🤷 Your link:
Water pump, xb 04-06 $92.34 $73.87

Unless the 7 is displayed as 5 on some computers 😉
TheSilkySmoothNew Hampshire · Feb 5, 2010#31
Hey, is there a water pump lube from toyota or coolant conditioner to add at say 30k miles? - I hear all these problems are from the long life coolant. My Rav4 WP puked at 50k miles too ;(
kouThread starternj · Mar 15, 2010#32
please sticky to DIY section.Thanks.
OtownYarisApopka, FL · Apr 24, 2010#33
I just had my water pump replaced today @ 33K miles. The car turns 3 years old this month. Kind of disappointing. The underside of my hood looked exactly as shown in the picture.
Lucas13Fort Lauderdale · Jun 11, 2010#34
Mine went out at 55k and other stuff is going out too such as my transmission leaking too!
bronsinnj · Jun 11, 2010#35
I think a Yaris is good but it doesnt appear to enjoy the stellar reliability of its forerunner the ECHO. Never heard of this wp issue with the ECHO and its even the same engine. Some have said the L life coolant is to blame. Does anyone know if any other Toyotas having wp issues? Wife has a Camry with 60k and so far so good.
auxmikeLI, New Yawk · Dec 5, 2010#36
Mom's 2006 Corolla pump lasted 16k.
Klink10910 · Dec 5, 2010#37
Just changed mine out last week after 15K. I attribute it to several factors which may or may not have been my fault. In either case I went to a discount OEM parts supplier and got one for $76.00. Did the work myself and changed up my NST pulley install procedure. I really do think that the weakest point on the Toyota waterpump is the seal around the bearing and that care should be used in the removal/install of the pulley and the tightening of the belt. I do know that Toyota offers no additive to the coolant used (Toyota Pink) in the Yaris. I also know that Toyota had 2 types of coolant and some dealers or whatever may still have the obsolete (Toyota Red) still around. The red is straight while the pink is a pre-mix. For info, if you look at the back of the "pink" jug it says that if you flush use only the "pink" to flush with and not "any kind" of water. The logic I assume is that you can't get all your flush out and thus would be dilluting your new stuff. Personally, after having read other stories I took it to heart and went with their advise. I know others have done it different and seem to be doing okay. Me, this is the way I went.
DARK AGE 53Alabama · Dec 5, 2010#38
if the water pump is covered under the drivetrain warranty then I'm good for life, hopefully I won't have to find out.
budzrsikzn · Dec 18, 2010#39
Hi guys! Anyone knows whether there suppose to sealant applied after the pump is changed? Cos it did come wid an o-ring.
Klink10910 · Dec 18, 2010#40
Originally Posted by budzrsi ↑
Hi guys! Anyone knows whether there suppose to sealant applied after the pump is changed? Cos it did come wid an o-ring.
No sealant supplied. The service manual which I used as reference mentioned no sealant either. Didn't use any. Mine is an 07.
birdmanUSA · Mar 3, 2011#41
Nice write up so now I know where to watch for crystal formation.
TickleTimeTimArkansas · Mar 15, 2011#42
my hood looked like that but not pink. not sure how long it has been out, but the squeaking is getting worse...like much worse.
auxmikeLI, New Yawk · Mar 15, 2011#43
Originally Posted by kou ↑
Maybe just the way the belt is tensioned from the factory.
Yeah, I tried to match that factory setting by marking the position with a sharpie when replacing the old pump and I could'nt pull hard enough to even get it THAT darn tight!
I got it close to the factory "mark", and the new pump went about 2k before it started spritzing again....
I check the "new" (2nd) pump almost daily, it only spritzes very little every other day, it's been that way since Xmas. Mabye I'll install a 3rd new pump once the weather improves (I have an AC Delco unit stashed)👏
marcustoronto, canada · Jun 27, 2011#44
looks pretty simple thinking of getting ac delco water pump might be better than toyota..i just dont get how to drop your engine 2 inches..
ROCKLANDTOYOTAROCKLAND TOYOTA/SCION · Jun 27, 2011#45
Originally Posted by DARK AGE 53 ↑
if the water pump is covered under the drivetrain warranty then I'm good for life, hopefully I won't have to find out.
NOT A CHANCE 3/36
goliath1812Ocala Florida · Jun 27, 2011#46
Originally Posted by marcus ↑
i just dont get how to drop your engine 2 inches..
+1

I removed the bolts from the motor mount, but the motor didn't go anywhere. Even with the jack not supporting it at all....
auxmikeLI, New Yawk · Jun 27, 2011#47
Here's my Delco pump and FelPro gasket I keep handy....
P1000834.JPGP1000835.JPGP1000836.JPGP1000837.JPGP1000838.JPG
marcustoronto, canada · Jun 27, 2011#48
thats exactly what i want on the yaris..looks more durable than oem!!
ROCKLANDTOYOTAROCKLAND TOYOTA/SCION · Jun 28, 2011#49
Originally Posted by auxmike ↑
Here's my Delco pump and FelPro gasket I keep handy....
WHY does the 2 gaskets in the last picture look different??
Bluevitz-rsOshawa, Ontario, Canada · Jun 28, 2011#50
Originally Posted by marcus ↑
looks pretty simple thinking of getting ac delco water pump might be better than toyota..i just dont get how to drop your engine 2 inches..
Put a jack under the oil pan and undo the passenger side motor mount.