I'm trying to install my Tanabe DF springs, how do you remove the nut on top of the front struts??? I can get a socket on top but then I can't get the wrench on the socket to turn it. Help please if you can :)
Help with lowering
17 posts · 5,968 views
Replies 16
Have u tried the search button for a Tanabe DF DIY??
those search engines are powerful....
those search engines are powerful....
Yeah, I just noticed the howto section. When I found the site thru google it took me right to a forum page and I didnt notice the YW front page with the easy link.
Sorry for the laziness. I'm BIG on forums so I know how annoying it can be when someone does what I just did. My bad...
Sorry for the laziness. I'm BIG on forums so I know how annoying it can be when someone does what I just did. My bad...
You need a 19mm wrench
Originally Posted by YamilR ↑You need a 19mm wrench
sorry but i just did mine and it was a 17mm for both top bolts...
the 19mm its the 2 lower one that are bolted to the hub...😉
the fist one on top i removed it with an impact gun
I just used my fingers because I am so tough and strong.😆
Didn't I mention that I also know -everything-. 😆 🙄
Didn't I mention that I also know -everything-. 😆 🙄
Reading that how-to helped alot. I saw something online about remove the wiper tray with the wipers and all, I just couldn't believe that was the way. BUT sure enough it was....It was a lot easier then I thought too!! :) 2 hrs for the total install.
Here it is:
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Here it is:
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Out of curiosity did you start at the front, or the rear? Which springs did you use?Originally Posted by Turbo&Auto ↑Reading that how-to helped alot. I saw something online about remove the wiper tray with the wipers and all, I just couldn't believe that was the way. BUT sure enough it was....It was a lot easier then I thought too!! :) 2 hrs for the total install.
I started with the front since I figured it would be the most tough.
Tanabe DF's.
Tanabe DF's.
That would be my approach. Get the crappy part done, and then move on to the easy stuff. I assume you spent most of your time on the front end? Where did you place your jack for the front end work? I assume you brought both tires off the ground at the same time?Originally Posted by Turbo&Auto ↑I started with the front since I figured it would be the most tough.
Tanabe DF's.
BTW, Where are you located at in PA?
I put mine up on jack stands🙂
Front was a little time consuming for me all that goddamn turning and spring compressing, won't be so bad putting in the coilovers.
Front was a little time consuming for me all that goddamn turning and spring compressing, won't be so bad putting in the coilovers.
The only thing I hate about unibody is the lack of a frame! I always worry about crunching body work even though I use the designated jacking points.Originally Posted by brickhardmeat ↑I put mine up on jack stands🙂
Front was a little time consuming for me all that goddamn turning and spring compressing, won't be so bad putting in the coilovers.
I always try and push the car off the stands before I start.😉
Of course with this car you kind of feel like you will dent or break something whaling on it as mentioned by others.😆
Of course with this car you kind of feel like you will dent or break something whaling on it as mentioned by others.😆
I assume that maneuver is an effort to cause a natural obstruction from drive buys whilst you are wrenching in "Big D"! 😁Originally Posted by brickhardmeat ↑I always try and push the car off the stands before I start.😉
Of course with this car you kind of feel like you will dent or break something whaling on it as mentioned by others.😆
Yeah I'm wrong, I meant to say 17mm box wrench. It's being 6 months and 8000 miles later and they look even better once they settleOriginally Posted by Toymaniac ↑sorry but i just did mine and it was a 17mm for both top bolts...
the 19mm its the 2 lower one that are bolted to the hub...😉
the fist one on top i removed it with an impact gun
Here's the DIY by Chris07LB
TANABE DF210 Spring Install [pics]
TANABE DF210 Spring Install [pics]
So, now that your ass is sagin you are one with the force? 😁Originally Posted by YamilR ↑Yeah I'm wrong, I meant to say 17mm box wrench. It's being 6 months and 8000 miles later and they look even better once they settle