iwanttobeamoleOriginal postHamilton - New Zealand · Mar 9, 2013#1After a number of months of saving and planning, it's come time to upgrade my supercharged 2nz-fe engine in my 2000 Yaris.
I'm planning on a 1nz-fe running some lower compression pistons and stronger rods, amongst a few other things, but I'm very interested in any ideas, hints and experiences of those out there who have been down this route.
So .. My current set up is as below
Engine: 2nz-fe 1.3L, completely stock.
Jimze supercharger kit (I believe it's an Eaton M45 supercharger) with K&N CAI.
Supercharger is running up to 10.8psi at rev limit (6500rpm), but as a result the ignition timing has been pulled right back to stop the thing from detonating, give it's still running stock compression. (10.5:1)
The ECU is a Link G4 Storm which is a complete replacement. It made 74wkw (~100whp) So not terrible for a 1.3, but not anything too amazing.
The plan.
Obviously a 1nz-fe to start with. I'm planning to put some wiseco low compression pistons in. At this point I'm thinking 9:1 compression, but am open to advice here. Obviously with a larger displacement I'll be looking at a little less boost with the same S/C drive ratio. Obviously some stronger rods also, which I've sourced locally.
I'll be building the engine on a stand so have the advantage of having time to do what I want to do.
Without going overboard (as I don't have an unlimited budget) I'm looking at some amount of head work, including:
Port and polish
I'm looking at a cam grind. Kelford here in New Zealand offer a reasonably priced cam grind service.
I wouldn't mind getting some more revs out of it so perhaps some stiffer valve springs to facilitate that. I saw a set on the microimage online shop which look good.
Other than that I'm looking at a lighter flywheel. There's a JUN one available for ~38k Yen out of RHDJapan.com which looks Tidy, but for less than half of that I can get a standard flywheel lightened and balanced. Anyone got any experience here? How much lighter can you make a standard 1nz-fe flywheel?
I'm going to leave the gearbox and diff alone at this stage. Maybe that'll be the next step in the project.
As for fuel, I'm running the standard fuel rail and pump at present but with some "derestricted" 1zz injectors which now flow at ~700cc with a nice clean spray pattern.
Goal
The aim here is to make a reliable, relatively economical engine that's making somewhere in the 100-110wkw range. I drive the car a lot for work (~800km's a week) so I need it to be well behaved.
So that's the plan. As I said I'm open to any ideas or experiences that people have had specifically regarding running a lower compression setup for boost and strength.
Is there anything glaringly obvious that I've missed that I need to look at?
Also worth noting, I know I'd get more power from a turbo setup, but I'm a huge fan of a supercharger, so I'm going to stick with it for now. I might look at a turbo build at some stage in the future. :)
Here's the car and Dyno sheet from the current tune.
Picture not included in this copy
Picture not included in this copy
#Edit - I'm going through fixing the links to the pics because photobucket sucks. Hopefully I get them right
Replies 65
CrankyOldManWest Michigan · Mar 9, 2013#2Sweet jeebus. Eaton has the following to say about the M45 series:
The Eaton Supercharger Model 45 is designed for 2.0L to 3.0L passenger car and light truck engines, but may also be suitable for other engine sizes, depending on total system performance requirements.
Microimage also sells lightweight flywheels in a few different flavors, at price points near your 38k Yen example. They're also willing to ship internationally.
Aside from that, I can probably shed some light on the gearbox/diff questions when you get to that stage.
cali yarisCanoga Park, CA · Mar 10, 2013#3 The aim here is to make a reliable, relatively economical engine that's making somewhere in the 100-110wkw range.
Only reason to run lower compression is to run higher boost levels and be able to tune it while avoiding detonation.
This is, I believe,
not consistent with your stated power goal.
Our light flywheels are approx. 9 pounds. Stock is, as I recall, about 16 pounds?
iwanttobeamoleThread starterHamilton - New Zealand · Mar 10, 2013#4 Originally Posted by
cali yaris ↑ Only reason to run lower compression is to run higher boost levels and be able to tune it while avoiding detonation.
This is, I believe, not consistent with your stated power goal.
Our light flywheels are approx. 9 pounds. Stock is, as I recall, about 16 pounds?
Surely there's some benefit to lowering the compression? With the goal of pushing up to 1bar through it?
rob323Joyner, Brisbane · Mar 11, 2013#5Can you actually get a smaller pulley to be able to increase the boost or is it something that will have to be machined up?
I see no real downside in dropping the compression slightly, but you won't be running as much boost with the std pulley on a 1NZ motor. Any headwork and cams will also drop the dynamic compression.
My plans involve swapping the rods for stronger ones but retaining the stock pistons so that no machining/ honing needs to be done. That in conjunction with cams and high octane fuel should easily keep detonation at bay.
Is the Link ecu connected to the factory knock sensor?
iwanttobeamoleThread starterHamilton - New Zealand · Mar 11, 2013#6 Originally Posted by
rob323 ↑ Can you actually get a smaller pulley to be able to increase the boost or is it something that will have to be machined up?
I see no real downside in dropping the compression slightly, but you won't be running as much boost with the std pulley on a 1NZ motor. Any headwork and cams will also drop the dynamic compression.
My plans involve swapping the rods for stronger ones but retaining the stock pistons so that no machining/ honing needs to be done. That in conjunction with cams and high octane fuel should easily keep detonation at bay.
Is the Link ecu connected to the factory knock sensor?
I'd need to get a smaller pulley made up I think. There's also a possibility going slightly larger on the double pulley on the alternator but there's not a lot of room between it and the tensioner pulley. Also looking at some stiffer valve springs to facilitate more engine RPM which should help to raise the max boost.
I'll initially just get set up with the new engine, then look at upping the boost.
I think you'll be fine to stick with the stock pistons for the rally car, as higher octane fuel is a bit more feasible. As my car is a daily driver and I do ~800km a week, I'm tuned on 95 octane so it's not too expensive to run.
I know the link was tuned with a knock sensor, but I don't think it talks to the factory knock sensor during normal operation. I guess in theory the conditions shouldn't change too much as long as I stick to 95 octane or higher.
iwanttobeamoleThread starterHamilton - New Zealand · Mar 26, 2013#7Small update on the build.
I've picked up a 1nz-fe, whipped the head off, and have taken it to my friendly local cylinder head shop for a cam grind, and a bit of tarting up. (ports, valve springs etc)
The engine has done a mere 70k's (~43k miles) so as you might imagine it's in pretty good shape. Immaculate even.
Bottom end will come out next week, then the crank goes for a balance along with the flywheel which I'll get a little cut out of.
Here's a pic with the head off. Not a lot to see but there it is.
Picture not included in this copy
Valve springs and exhaust manifold to come from micro image (thanks in advance Garm :)
More soon
iwanttobeamoleThread starterHamilton - New Zealand · Jun 8, 2013#8Well after about a million years waiting for parts they've all finally arrived.
Thanks to Garm for all the bits that showed up on time. No comment on the rest
Parts List
CP 9:1 comp Pistons
Molnar rods
1nz valve spring upgrade kit
Megan racing exhaust manifold
Lightened (stock) flywheel
Excedy Clutch kit
Other stuff
Cam grind, (not sure on the new specs as I don't have the head back yet)
Was going to get a port and polish but the budget wouldn't allow
Head work to suits new cams, etc.
Full balance on crank, rods, pistons, flywheel, clutch plate, Pulley etc.
Probably some other stuff I can't remember
Out with the old
Picture not included in this copy Picture not included in this copy In with the new
Picture not included in this copy Picture not included in this copy Bit of a pause at this stage in the post while some particularly talented person down the road thought it would be a good idea to set his neighbours car on fire. Fun times!
As with all aftermarket rods we ran into some clearance issues with the bottom of the cylinder. Hard to get a picture of it.
Picture not included in this copy But that was easily fixed
(Video)
https://imgur.com/WqpRiBf Don't worry, we tidied it up a little more after that.
Followed by test fitting, then rings, then piston installs, then this!
(another video)
https://imgur.com/OeTGfN7 At about this stage the
Diesel took over and we didn't get a lot more done.
Still, only a little more to do on the bottom end which we'll get into this week. I was hoping to have the head back from the head shop (Hamilton Cylinder Heads- For the best head job in town) but they couldn't quite get it done. Should have it back early next week, and hope to get that on next weekend.
Once the engine is together, we'll do the swap, with my 2nz. Then off to the tuner hopefully all before the end of the month.
Whisky time.
cali yarisCanoga Park, CA · Jun 8, 2013#9^ Awesome, well done! 🍻
iwanttobeamoleThread starterHamilton - New Zealand · Jun 11, 2013#10I noticed something about the Molnar rods that didn't match the stock ones.
The stock rods have an oil gallery that feeds from the big end, through the bearing , all the way up the rod to the small end, which then feeds through the oil rings in the piston.. simple.
However, the molnar rods don't have the same oil gallery in the rods, instead they just have some holes at the small end of the rod, which look like maybe they're meant to work with oil squirters or something??
Picture not included in this copy
Red circle where the stock rods have a gallery opening, and blue arrows where the molnar rods have the holes.
My 1nz-fe has no such oil squirters/delivery system aimed at the underside of the piston.
Is it something I should be worried about or is there enough oil splashing about down there to keep the pistons/cylinders well lubed?
I'm definitely over-thinking this.
cali yarisCanoga Park, CA · Jun 11, 2013#11Could take a look at Pauter or Crower rods to compare.
iwanttobeamoleThread starterHamilton - New Zealand · Jun 12, 2013#12If you have something in stock and could take a look Garm it would be interesting to now if the other brands also delete that gallery.
On closer inspection of the stock rods that feed doesn't go all the way up the rod, but just goes through the side of the rod at the big and and guess squirts oil up toward the piston.
In any case we decided to keep putting the engine together. Hopefully the chaps at Molnar know what they're doing.
I picked up the head from shop tonight, and we got it in place and bolted down. got the cams in and timing chain on, before we realised that the new head bolts hadn't come with washers... *facepalm*
Still, nothing a little back peddling couldn't fix.
We also bolted up the Megan Racing exhaust manifold, but discovered that it doesn't come close to marrying up with the factory brace, so I guess we'll have to do a little fabrication there as I'm not all that keen on just deleting the brace.
Will upload some pics tomorrow.
Sleep time now.
iwanttobeamoleThread starterHamilton - New Zealand · Jun 12, 2013#13head on
Picture not included in this copy
and back off again
Picture not included in this copy
Cams GO!
Picture not included in this copy
Lumpy(er than stock.. hopefully)
Picture not included in this copy
Cover on
Picture not included in this copy
Exhaust Manifold Comparisons
Picture not included in this copy
Closeup of the old
Picture not included in this copy
and new.
Picture not included in this copy
Minor problem with the Megan Racing exhaust manifold..
IE.. it's the wrong shape for the factory brace.
Picture not included in this copy
Picture not included in this copy
(edit - Turns out the newer 1nz-fe had a brace to suit so an easy fix after a visit to the wreckers)
Hopefully it clears the firewall, but I think there's plenty of room there.
Also of note is the plate on the manifold need a bit of machining to get it actually straight, but given the price I can't complain too much :)
Got the use of a workshop on the weekend of the 22nd/23rd to do the engine swap. Tune booked for Monday 24th. Can't wait!
iwanttobeamoleThread starterHamilton - New Zealand · Jun 12, 2013#14iwanttobeamoleThread starterHamilton - New Zealand · Jun 15, 2013#15Found the specs from the cam grind
Stock
Picture not included in this copy
After Grind
Picture not included in this copy
Also had an awesome response from Tom Molnar of Molnar technologies explaining their process and design for their rods. Awesome info from an awesome guy. Gave me some peace of mind about the rods and build in general. Thanks Tom!!
iwanttobeamoleThread starterHamilton - New Zealand · Jun 23, 2013#16On Friday night we headed down to a mates workshop to do the install.
Started at about 4:30pm, and finished up about 11 hours later.
The new donk
Picture not included in this copy
removal of the old engine with proprietary engine lifting system (yes it's an old ambulance stretcher)
Picture not included in this copy
Engine out
Picture not included in this copy
Fitting the new clutch and lightened flywheel. (turbo for scale)
Picture not included in this copy
Gave the intake manifold a tidy up as it was fairly dirty/oily in there from blowby (oil catch can now fitted.
Picture not included in this copy
At this point we also noted that there were some black marks in the old gasket goo between the S/C and the manifold suggesting it was leaking. I also tested the butterfly valve that is used for the bypass, which was also leaking heavily when I was just blowing through it.
So we sorted that out.
Picture not included in this copy
Less boost leaking out is always a good thing.
Had to find a bung to close up the return hole for the bypass valve.
Milk bottle to and a little glue sorted that issue out.
Picture not included in this copy
here's where the fun started.
Picture not included in this copy
The 2nz block is shorter than the 1nz block, and as it turns out that difference is somewhere between the alternator and the supercharger. We had to get a little creative as the alternator didn't reach it's tensioning slot.. so we had to improvise a little.
Got some washers, brazed them together, then cut them so they would support the other side of the alternator tensioner bolt, and just clamped it up so it grabbed the bottom of the slider bar. It's a little rangi mods, but it works for now.
Picture not included in this copy
We'll fix that properly later
##Edit## 6 years have passed. it's still the same. (see page 3 for details)
Also the 4PK 540 belt is JUST long enough to get around the two pulleys with no requirement for a tensioner bearing at all. I'll look at getting a longer belt at some point but the tension is about perfect at the moment so it's all set for the dyno tomorrow.
We had to slightly modify the bonnet as the S/C now sits a little higher, but we only needed to remove some of the fibreglass bracing material. It's a pretty close fit with the bonnet down, but it should be ok.
So we got it all back into the car, turned it over and it started straight away, and felt good, if a little loud with the exhaust not mounted up yet. It was getting on toward 4am so I got a little slack with the photos. Went back today to finish up a few things and tidy the workshop.
Last thing to do tomorrow morning is to take the car down to the muffler shop and get the exhaust modified to fit the megan racing header which was on a different angle and location to the stock setup, and the flange is a bit different. Should be able to sort it before leaving at 1pm, for the tune which is at 3:30 pm :)
Will report back in a little over 24 hours with the results.
I'm just hoping it doesn't grenade on the dyno because I forgot to tighten something somewhere.. :S
malibuguyWestminster, MD · Jun 23, 2013#17That header is for a later yaris...the echos/vitz has an outlet thats straight back. First gen scion xB and xA are the same as well. Plenty of proper fitting headers availible for your chassis.
iwanttobeamoleThread starterHamilton - New Zealand · Jun 26, 2013#18Got the exhaust all sorted and headed to the dyno on Monday.
Got a bit of base tuning done, then got it onto the dyno.
Picture not included in this copy
Well... First and foremost, then engine didn't explode! which is a bonus.
Did a few runs to check things out, and it was all looking good. By the looks of things though the boost has dropped quite a bit with the new capacity. it's only making about 8psi now where it was almost hitting 11 with the 1.3.
Unfortunately we we got to about 80kw, and the clutch started slipping. I had bought a decent exedy clutch, but it ended up being the wrong size, so had to get another at short notice, which turned out to be a pile of shit.
So we left the tune at that.. Lin (tuner) tidied it up a little and we pulled it off the dyno and I headed home.
On the bright side, it'll give the engine a nice wear in period, and give me some time to fit up a larger 1zz throttle body and get a new pulley made for the supercharger.
These M45's are the same S/C as the mini cooper S uses, and there's a lot of guys running up to 1bar through them, so I'm going to aim for something closer to that and hope the damn thing doesn't melt.
ilikericesavannah, ga · Jul 4, 2013#19awesome build thread. love your car.
iwanttobeamoleThread starterHamilton - New Zealand · Aug 28, 2013#20Picture not included in this copy
More to come soon.
cali yarisCanoga Park, CA · Aug 28, 2013#21underdrive s/c pulley? Sweet!
iwanttobeamoleThread starterHamilton - New Zealand · Nov 27, 2013#22So.....
it turns out that supercharger RPM is not directly proportional to boost.
I wanted 50% more boost, so I made the supercharger spin 50% fast. What this got me however was about 200% more boost, about 15psi at 2,000 RPM. Too much!
So.. back to the drawing board, I had another pulley made that increased pulley RPM by approx 22%, and this seems to have done the trick. It's installed and going well so far, but the ecu is set to boost cut at about 12psi, which it now hits at about 3500RPM.
Had to tweak the belts up pretty tight but they don't seem to be slipping so that's good.
Tune is booked for next Thursday.
ilikericesavannah, ga · Nov 28, 2013#2315lbs is what i want out of a supercharger. Can that charger hold that much boost?
cali yarisCanoga Park, CA · Nov 28, 2013#24awesome
iwanttobeamoleThread starterHamilton - New Zealand · Jan 20, 2014#25I was a little slack updating this but just before the end of last year I got this sorted out.
Had another pulley made with a 22% increase in diameter, which landed me this result.
(dotted line is the last run with the smaller pulley)
Picture not included in this copy
Boost is sitting at 0.9bar (13.25psi)
While the kw figure isn't too high at 89.6wkw (121whp for you non metric types) the torque figure went up another 20%! It's quite something to drive now.
Also worth noting here that it was tuned with reliability and economy in mind on 95 octane, not 98 (which is available here in NZ).
Overall I'm pretty happy with how it turned out.
Here's a bonus pic of my new intake pipe to fit the 55mm throttle body (4 bolt type from an 1zz)
Picture not included in this copy
hareNew Zealand · Jan 21, 2014#26is it no way to factory bolt on to the 1zz throttle body?
thanks for your sharing,really enjoy it!
iwanttobeamoleThread starterHamilton - New Zealand · Jan 21, 2014#27 Originally Posted by
hare ↑ is it no way to factory bolt on to the 1zz throttle body?
thanks for your sharing,really enjoy it!
There seem to be two different sorts of 1zz cable type throttle bodies (as opposed to fly-by-wire ones) One is a 50mm three bolt, and seems to swap to the 45mm yaris one just fine(according to other peoples experience, I never did this) The other is a 55mm 4 bolt type, which, as I was getting a new intake arm anyway, I chose to use as it's larger.
hope this helps :)
abstractmethodAustralia · Feb 21, 2014#28Great write up mate, keep us posted :D
iwanttobeamoleThread starterHamilton - New Zealand · Mar 18, 2014#29 Originally Posted by yaris edd ↑
hi ive just bought a jimze charger and its fucked do you recon there is any chance i could use the mini cooper s charger with my tb and manifold on it? they look different to me but they are both m45 arnt they? cheers
While the model is the same the housing looks quite different. Also I believe the mini S/C has some sort of oil pump built in, so that could complicate matters.
What's wrong with the s/c you bought? I know that sometimes the teflon coating fails but that can be re-done.
iwanttobeamoleThread starterHamilton - New Zealand · Aug 9, 2014#30Finally got around to making a little
video of the car.
Enjoy :)
rob323Joyner, Brisbane · Sep 3, 2014#31Great build up.
Are you still using a standard gearbox?
CrankyOldManWest Michigan · Sep 3, 2014#32LOVE the sound! I've finally gotten my S/C build under control and it's been phenomenally fun to drive.
iwanttobeamoleThread starterHamilton - New Zealand · Sep 11, 2014#33 Originally Posted by
rob323 ↑ Great build up.
Are you still using a standard gearbox?
Still using the stock gearbox. It seems to be handling the extra torque fine.
I've just been offered a 6 bolt TRD LSD for it, but sadly I'm now selling the car to make room for another project so I'll have to decline. :(
If I had the garaging I'd probably keep it cos it's SO MUCH FUN!
Ryze268Antigua & Barbuda · Sep 11, 2014#34Nooooooo, keep the Vitz dream alive :(
iwanttobeamoleThread starterHamilton - New Zealand · Feb 18, 2020#35So ... this happened.
Picture not included in this copy
iwanttobeamoleThread starterHamilton - New Zealand · Feb 19, 2020#36Ok so that was a bit cryptic.
I've fixed the links in the build thread now, driven by a seething hatred for photobucket.
Here's the short version
I sold the car in ~2014.
In 2019 I saw it come up for sale but, it had been re-shelled (assume it was crashed?) and it was a bit shabby. While I liked the idea, didn't want the headache.
Turns out a friend of a friend (Genuine GC) bought it, tidied a lot of the shabbyness up. I got talking to him at the time he bought it and gave him the history and the car and offered any help I could assist with, but also mentioned the old... " if you sell it, tell me first"
Well....
His wife's just had baby #2. He emailed me last week and asked if I was interested.. then made me an offer I couldn't refuse..
My circumstances have changed and now I have a bit more space, (but no more time).
So now I have, most of (the important bits) my old car back.
I've just drive down country with it (about 500kms) and aside from the supercharger being slightly skewed so the belt hops over one tooth, it's running very well.
From my memory of 6-7 years ago the power is still good, the seats are still terrible, and I think the new chassis is better than the old one (less rattles etc)
All the important pieces have been swapped to the new shell so that's good!.
I always felt like the project wasn't complete, but my dream car came up (JDM Honda Integra DC5, with a K24/K20 hybrid motor already done) came up. (which I've now supercharged also....) and at the time I didn't have the space, time , or money to deal with a second project car.
Now I have the chance to complete the project and hopefully realise it's full potential.
Here's the list.
- Full exhaust ( currently most of it are stock at I believe 1.75")
- Intercooler - The aim is to modify the manifold or build a new one that allows for the charge to be intercooled
- Sort out VVT-i which seems to be weirdly non-effective. (research required)
- Fit wideband
- Tune
Obviously having dredged this post up from the dark ages, I mean to keep it updated, so, I guess, Watch this space.
CrankyOldManWest Michigan · Feb 19, 2020#37The older I get, the smaller the world gets. Great to see that it came back to you, and in good condition!
06YarisRSFredericton, New Brunswick, Canada · Feb 19, 2020#38This is great! So happy to see more discussion about forced induction Yari! Yay!
iwanttobeamoleThread starterHamilton - New Zealand · Feb 23, 2020#39Small update.
Got a boost gauge and mounted it up.
Was able to test drive the car and check the boost levels which seem to be much the same as before, around 0.9bar or just over 13PSI.
Love the response out of a positive displacement supercharger.
Little
Video here Final pillar mount setup. Not all that pretty, but I'm all about function over form.
Picture not included in this copy Catching up with a mate this week and we'll discuss the plan to modify the intake manifold to output and input so I can run it through an intercooler.
Also making plans to finally fix the exhaust which is stock (I believe 1.75") between the (Megan Racing) headers and rear muffler.
I'm thinking we'll go 2.5" all the way through with a nice center resolator, and decent rear muffler.
Will also be fitting up a wideband at the same time for future tuning etc. Not too sure where I'll be mounting all the gauges yet. Maybe in the little center top sunglasses? holder if they fit.
More as it happens.
CrankyOldManWest Michigan · Feb 24, 2020#40I ran stock exhaust up until I did the 1.8 swap, then went to 2.25. I think 2.5 may be hard to route as well as overkill. I started with a straight pipe from the first cat to a Dynomax VT muffler (has a flap like our stock one) and added an inline "race bullet" where the stock resonator goes to take out some of the drone. Pretty happy with the result, considering how much engineering goes into an OEM exhaust.
06YarisRSFredericton, New Brunswick, Canada · Feb 24, 2020#41 Originally Posted by
iwanttobeamole ↑
Also making plans to finally fix the exhaust which is stock (I believe 1.75") between the (Megan Racing) headers and rear muffler.
I'm thinking we'll go 2.5" all the way through with a nice center resolator, and decent rear muffler.
This is basically the same setup I have. Front to back:
3" downpipe with two 02 sensor ports -> 3" x 2.5" reducing coupler -> high flow CAT (with downstream 02 port) -> 18" "cherry bomb" style muffler -> rear turbo (Walker) 2.5" in, 2.5" out muffler -> 2.5" x 4" SS stubby exhaust tip. Mine was all crush bent so probably not as free-flowing as a 2.25" mandrel bent setup. But, it works great and EGTs are good.
Cranky is right. 2.5 was hard to get tucked up in there. If I had more money, I would go for a mandrel bent SS system.
myfirstyotaToronto Canada · Feb 25, 2020#42I have the magnaflow ss 2.25" system from exhaust manifold to muffler in the 2zr swapped car (still need a nice free flowing muffler). Its a nice setup but set me back over 600cad.
06YarisRSFredericton, New Brunswick, Canada · Feb 25, 2020#43 Originally Posted by
myfirstyota ↑ I have the magnaflow ss 2.25" system from exhaust manifold to muffler in the 2zr swapped car (still need a nice free flowing muffler). Its a nice setup but set me back over 600cad.
Yes, I think I mentioned earlier that I
almost had one. TDot Performance listed them but they were out of stock. They kept the listing up for a long time after. It is a beautiful looking system. You must be really happy with it. I bet is sounds great too.
myfirstyotaToronto Canada · Feb 26, 2020#44 Originally Posted by
06YarisRS ↑ Yes, I think I mentioned earlier that I almost had one. TDot Performance listed them but they were out of stock. They kept the listing up for a long time after. It is a beautiful looking system. You must be really happy with it. I bet is sounds great too.
Hard to tell how the sound is. The car is currently running the stock scion xd muffler.
I also cut the fender side out of the oem air box, removed the charcoal filter and obviously the silencer horn as it's useless with the side of the air box missing.
The muffler is the biggest bottleneck in the system. I'll get a nice one installed this spring when the beast comes home from storage. But even with it's current setup, I'm content with the sound.
iwanttobeamoleThread starterHamilton - New Zealand · Jul 1, 2020#45Well.. I guess that was Covid.
Further updates. Short version.
The pulley came loose for some reason (possibly the nut came loose and flogged out the keyway, possible the keyway came loose, flogged itself out ,and loosened the nut.
Either way what it needed was a new input shaft and pulley.
Located said items at superchargersonline.com (Thanks David) for the intake shaft and rebuild kit (might as well do the bearings while I'm at it) and pulleyboys.com for the pulley.....s.
I figured since I plan to intercool it I might end up loosing some pressure so got a 3.0" and a 2.8" just in case I need to spin it a little faster.
Those arrived today
Picture not included in this copy
Also dropped the manifold off to a local outfit to have it vapourblasted to clean it up for welding as it's cast aluminium. (yes I spelt that correctly)
Once the shaft and snout rebuild kit arrive I can re-assemble that.
Meanwhile here's the list
- Get the intake manifold modified to output the charge through the front/bottom,
- Procure and mount intercooler
- Plumb said intercooler to manifold
- Mount new open element air intake temp sensor into the manifold somewhere.
- Rebuild S/C snout and re-assemble.
- re-assemble
- Exhaust
- Tune
- Skids
More soon!
thebarberGrand Rapids, MI · Jul 7, 2020#46fwiw, i had the blitz with a DC header and a 2.25" exhaust (back end of resonator to a megan axleback muffler) and was happy. 2.5 wouldve been at bit big, i wager.
iwanttobeamoleThread starterHamilton - New Zealand · Jul 27, 2020#47The work continues.
Picture not included in this copy
More soon
GorillaSydney, Australia · Aug 1, 2020#48Welcome back mate! I remember seeing the car up for sale as I always trawl NZ FB Market Place and Trademe! You have to look into getting a C56 from the Vitz RS, there are a few wreckers in NZ that will have them. I put one in mine (LSD From Turbo Model) and its probably my favourite mod. Shorter ratios and LSD.
malibuguyWestminster, MD · Aug 3, 2020#49heads up about the Megan axle backs. I had one come in on a Yaris hatchie years ago and inside the muffler core was 1.5-1.75" tops. Keeps it quiet but sure as shit not much of an improvement in flow.
iwanttobeamoleThread starterHamilton - New Zealand · Sep 20, 2020#50So..
Supercharger parts arrived (ages ago) and I've gotten the blower reassembled with the new shaft, bearings, and pulley.
Picture not included in this copy
Blocked up the "silencer" holes with some aluminium wedges and welded those in, then some 2 part epoxy (loctite stuff, but same same as J weld) Should make good noises now.
Picture not included in this copy
Finished and fitted up the modified intake manifold
Picture not included in this copy
Bought and fitted up a "same side" intercooler.
Picture not included in this copy
And plumbed it.
Picture not included in this copy
Picture not included in this copy
Slapped it all back together and cut a dirty great hole in the front bumper (don't judge me)
Picture not included in this copy
As there are no gaskets for this setup I've used RTV which is drying now. Should be good for a test run tomorrow.
*excite*