Aaaaand now it sounds like this.
https://www.youtube.com/watch?v=G7g1UYw7D9U
Note: Lots of belt slip due to the accessory belt being a bit loose.
Evidently those silencer holes I blocked up REALLY make it a lot quieter.
Now.. the main motivation for this build is definitely the lols but.. this was a bit much.
Turns out a noisy supercharger at low revs with no bypass or silencer slots/holes sounds like every gearbox bearing is about to have a critical failure. This meant that literally everyone I drove passed looked at me with that "that car is about to explode" look. While I don't care about.. well.. people. I tended to agree with them in this instance.
Another issue I experienced was that, because of the increase in the volume between the supercharger and engine, and the lack of bypass valve, coming off throttle was less responsive than desired and resulting in... throttle hang? EG: if you come off throttle and onto the clutch to change gears, you'd get an unwanted rev blip while the existing volume of already compressed air in the intercooler, plumbing and manifold was used up by the engine.
So.... I busted out the old parts from the previous iterations of this car (which I have kept .. because. . you know, they might be useful) and have now reinstalled the bypass valve which bypasses the supercharger (actually it just equalises the pressure) while in vacuum, and closes off once the blower makes positive pressure. Pretty normal supercharger stuff.
So this of course required some highly accurate measurements then a trip to a friends place for some tig goodness.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Then.. a quick bit of fabrication and..
Picture not included in this copy
Picture not included in this copy
I hoped that the installation of the bypass valve would resolve this issue, and.. I WAS RIGHT! With the bypass in place the car now drives like it did before, but now the intercooler is in place I expect a lower intake temp and therefore the hope to be able to advance timing and make a bit more power.
Interestingly the boost level at the manifold has dropped from about 13psi to about 9. I haven't found a chart to back it up, but I think at least some of this is from the drop in temperature. HOWEVER, I've noticed a couple of things. Firstly, the car feels about as fast as it was before, and secondly the belt doesn't seem to slip nearly as much as before. It's hard compare, but I'm 97% sure that before I NEVER had a run to rev limit (7200RPM) without belt slip. Now, even with the tensioner for the supercharger belt maxxed out and the belt not that tight, it holds. The car makes good power all the way to red line, albeit limited noticably at higher revs by the extremely restrictive exhaust. More on that soon though.
The other issues that appeared, somewhat predictably, is that the larger silicon joiners, (the 90 degree and 45 degree ones specifically) tried to turn themselves inside out every time the car was in vacuum. This was not ideal, so I ended up sleeving the joiners with some 2" alloy bends I had laying about. This experience, while painful (many many cuts to my delicate indoor typing fingers) was successful, and the joiners now hold their shape under vacuum.
So.. next on the list.. going to see my chap tomorrow to make a plan for the exhaust. Once that's freed up and the wideband installed, wire in the AIT sensor and head to the tuner for road and dyno tuning.
I have no idea what it'll make. It made 90wkw before with lots of things wrong. I don't want to put any unrealistic figures in my head, but I feel like the intercooler and exhaust should free up a good about of, specially top end power.
More to come so stay tuned (assuming anyone is still tuned?)
https://www.youtube.com/watch?v=G7g1UYw7D9U
Note: Lots of belt slip due to the accessory belt being a bit loose.
Evidently those silencer holes I blocked up REALLY make it a lot quieter.
Now.. the main motivation for this build is definitely the lols but.. this was a bit much.
Turns out a noisy supercharger at low revs with no bypass or silencer slots/holes sounds like every gearbox bearing is about to have a critical failure. This meant that literally everyone I drove passed looked at me with that "that car is about to explode" look. While I don't care about.. well.. people. I tended to agree with them in this instance.
Another issue I experienced was that, because of the increase in the volume between the supercharger and engine, and the lack of bypass valve, coming off throttle was less responsive than desired and resulting in... throttle hang? EG: if you come off throttle and onto the clutch to change gears, you'd get an unwanted rev blip while the existing volume of already compressed air in the intercooler, plumbing and manifold was used up by the engine.
So.... I busted out the old parts from the previous iterations of this car (which I have kept .. because. . you know, they might be useful) and have now reinstalled the bypass valve which bypasses the supercharger (actually it just equalises the pressure) while in vacuum, and closes off once the blower makes positive pressure. Pretty normal supercharger stuff.
So this of course required some highly accurate measurements then a trip to a friends place for some tig goodness.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Then.. a quick bit of fabrication and..
Picture not included in this copy
Picture not included in this copy
I hoped that the installation of the bypass valve would resolve this issue, and.. I WAS RIGHT! With the bypass in place the car now drives like it did before, but now the intercooler is in place I expect a lower intake temp and therefore the hope to be able to advance timing and make a bit more power.
Interestingly the boost level at the manifold has dropped from about 13psi to about 9. I haven't found a chart to back it up, but I think at least some of this is from the drop in temperature. HOWEVER, I've noticed a couple of things. Firstly, the car feels about as fast as it was before, and secondly the belt doesn't seem to slip nearly as much as before. It's hard compare, but I'm 97% sure that before I NEVER had a run to rev limit (7200RPM) without belt slip. Now, even with the tensioner for the supercharger belt maxxed out and the belt not that tight, it holds. The car makes good power all the way to red line, albeit limited noticably at higher revs by the extremely restrictive exhaust. More on that soon though.
The other issues that appeared, somewhat predictably, is that the larger silicon joiners, (the 90 degree and 45 degree ones specifically) tried to turn themselves inside out every time the car was in vacuum. This was not ideal, so I ended up sleeving the joiners with some 2" alloy bends I had laying about. This experience, while painful (many many cuts to my delicate indoor typing fingers) was successful, and the joiners now hold their shape under vacuum.
So.. next on the list.. going to see my chap tomorrow to make a plan for the exhaust. Once that's freed up and the wideband installed, wire in the AIT sensor and head to the tuner for road and dyno tuning.
I have no idea what it'll make. It made 90wkw before with lots of things wrong. I don't want to put any unrealistic figures in my head, but I feel like the intercooler and exhaust should free up a good about of, specially top end power.
More to come so stay tuned (assuming anyone is still tuned?)