Ohhh yeah man definitely. That does make sense though. I'm used to driving slammed, I'm just not used to driving low with poke. Now that I will have to get used to lol.Originally Posted by 1.5 ↑youre debating whether to go low now and then get new wheels or wait, get new wheels and then go lower. I say go with the first that way you get used to being that slammed and then you only have to get used to new wheels when theyre on. If you wait to slam it until after wheels then youre trying to get used to new ride height and new wheels. Its always wise to do one thing at a time, especially with extreme mods like slammed height and wild fitment, diagnosing problems is easier too
My 2011 Vitz
655 posts · 261,587 views · page 5 of 14
Replies continued
lol its fun dude, I rub like 24/7 people get scared when I come around the corner just shredding tire on fender at full lock lol, axle banging on my frame and crap lol, yesterday i was trying to pass traffic that was merging onto the highway, i pass a dc2 teggy with some mods that gives me some looks and as i switch lanes back in front of him i hit a small bump and sent sparks all over him lol thats the G sh** lol
Damn, I need that in my life hahaha.Originally Posted by 1.5 ↑lol its fun dude, I rub like 24/7 people get scared when I come around the corner just shredding tire on fender at full lock lol, axle banging on my frame and crap lol, yesterday i was trying to pass traffic that was merging onto the highway, i pass a dc2 teggy with some mods that gives me some looks and as i switch lanes back in front of him i hit a small bump and sent sparks all over him lol thats the G sh** lol
The rears are still uneven.. It's bothering me a lotttt. Lol. Anyone else have this problem with Megan Racing coilovers? I took off the locks, and perches, and they're still uneven! The rear driver side is like a little more than a quarter of an inch lower than the rear passenger side. I'm stuck. On top of that my ABS and VSC lights are still on. I wonder if they even work anymore..
My rear is also uneven. It must just be the car body isnt just not even laterally but also ride height.
My passenger side (or is it driver i forget) is like yours about a 1/4 inch lower. I have to keep one ring on the perch just to even it out. So one side has a ring the other doesnt.
As for ABS and VSC. Check the abs connector. either its loose or the abs sensor is dirty.
My passenger side (or is it driver i forget) is like yours about a 1/4 inch lower. I have to keep one ring on the perch just to even it out. So one side has a ring the other doesnt.
As for ABS and VSC. Check the abs connector. either its loose or the abs sensor is dirty.
Ahh okay so at least I know I'm not the only one with this problem! Thanks for the help man. My friends say I might have stretched the wires when we lowered it or something like that..Originally Posted by ezhacker1 ↑My rear is also uneven. It must just be the car body isnt just not even laterally but also ride height.
My passenger side (or is it driver i forget) is like yours about a 1/4 inch lower. I have to keep one ring on the perch just to even it out. So one side has a ring the other doesnt.
As for ABS and VSC. Check the abs connector. either its loose or the abs sensor is dirty.
You guys see the difference in height in the top picture? The rear is just a little higher but its bothering me haha.
Picture not included in this copy
Picture not included in this copy
Here's a picture of her good side haha. This is how low I want the rear to be. (Obviously since I cannot go any lower until I get shorter stiffer springs haha)
Picture not included in this copy
Picture not included in this copy
I wanna get my stock wheels back out to see how low the car looks with them on lol.
But yeah, maybe just add the perch to the driver side. I myself wouldnt ride without the perches, then again im on 9k 6" springs so they dont compress much so can fall out.
Being lazy that I am, what are the spring rates on the megans, and are the rear shocks height adjustable?
But yeah, maybe just add the perch to the driver side. I myself wouldnt ride without the perches, then again im on 9k 6" springs so they dont compress much so can fall out.
Being lazy that I am, what are the spring rates on the megans, and are the rear shocks height adjustable?
Hey Jonathan, didn't you tell me about these springs you saw on eBay?
Fronts are 5k, Rears are 2.5k. Yeah if if these springs did not compress the way they do I would not ride without the perches either. Also, the rear shocks are height adjustable. But I threaded them down to the limit I think. There are still threads but it would not let me go down and more. I don't know why. Laz said he thinks they're supposed to stop there. I'll post pics.Originally Posted by ezhacker1 ↑I wanna get my stock wheels back out to see how low the car looks with them on lol.
But yeah, maybe just add the perch to the driver side. I myself wouldnt ride without the perches, then again im on 9k 6" springs so they dont compress much so can fall out.
Being lazy that I am, what are the spring rates on the megans, and are the rear shocks height adjustable?
Here is the driver side rear shock. It looks like I can thread the nut lower but I remember not being able to.. Guess it wouldn't hurt to try. If I could thread the nut down just a little more on the passenger side that would be PERFECT!
Picture not included in this copy
Picture not included in this copy
yeah i got Stance coil springs to replace the 4k/4k from my cusco setup. about 50-60shipped per pair on ebay.
How much preload are you running on the front and back? you can lower the back to an extent with the strut height, but keep in mind every time the back wheels are off the ground, the spring will be pulling the strut apart, also you reduce the strut shaft travel length.
How much preload are you running on the front and back? you can lower the back to an extent with the strut height, but keep in mind every time the back wheels are off the ground, the spring will be pulling the strut apart, also you reduce the strut shaft travel length.
For sure thanks man. What're the spring rates on your Stance springs? Also, preload I'm not quite sure.. My friend helped out with that. For the rears I don't think we did any preload for that..Originally Posted by ezhacker1 ↑yeah i got Stance coil springs to replace the 4k/4k from my cusco setup. about 50-60shipped per pair on ebay.
How much preload are you running on the front and back? you can lower the back to an extent with the strut height, but keep in mind every time the back wheels are off the ground, the spring will be pulling the strut apart, also you reduce the strut shaft travel length.
9K/9k Stance 6in springs.
yeah keep preload to a bare minimum, least for the front. The rears, actually you cant preload it, because moving the strut body just moves amount of shaft travel. But still you can bust a strut .
You cant get any more lower/higher than what the springs/ spring perch / lock rings give you or lack there of. So trying to thread that rear strut lower, wont give you more low. The front yeah, the shock body adjusting will control the car height, and not the spring lock ring.
yeah keep preload to a bare minimum, least for the front. The rears, actually you cant preload it, because moving the strut body just moves amount of shaft travel. But still you can bust a strut .
You cant get any more lower/higher than what the springs/ spring perch / lock rings give you or lack there of. So trying to thread that rear strut lower, wont give you more low. The front yeah, the shock body adjusting will control the car height, and not the spring lock ring.
@terrence I cannot tell the difference lol. Also do not shorten your shock much more. All of us with Megans who went too short with out shock length wound up blowing the shock.
Originally Posted by ezhacker1 ↑9K/9k Stance 6in springs.
yeah keep preload to a bare minimum, least for the front. The rears, actually you cant preload it, because moving the strut body just moves amount of shaft travel. But still you can bust a strut .
You cant get any more lower/higher than what the springs/ spring perch / lock rings give you or lack there of. So trying to thread that rear strut lower, wont give you more low. The front yeah, the shock body adjusting will control the car height, and not the spring lock ring.
Ahh gotcha. Guess I gotta leave it alone for now until I get those springs. They're shorter right? That way I can add the locks/perches and still go as low?
Really?? Haha damn I hella see it. Definitely man I won't be touching them. I'll have to deal with it until I get shorter springs. So I'll be okay if I leave it where it is?Originally Posted by 1.5 ↑@terrence I cannot tell the difference lol. Also do not shorten your shock much more. All of us with Megans who went too short with out shock length wound up blowing the shock.
Yeah, measure your springs should be 7in. I have 6in stiffer springs. Basically measure how much your rear springs compress compared to its free length. You can calculate how much drop any spring will give with stated spring rates.
Course you could go with same spring rate but shorter springs.
Course you could go with same spring rate but shorter springs.
Sweet. Thanks for the help man. The ones I'm looking at are - 6k 150mm / 336lb 6in. Looking for the pair with 9k spring rates. I was thinking about just changing the rear springs.Originally Posted by ezhacker1 ↑Yeah, measure your springs should be 7in. I have 6in stiffer springs. Basically measure how much your rear springs compress compared to its free length. You can calculate how much drop any spring will give with stated spring rates.
Course you could go with same spring rate but shorter springs.
Yeah, seeing they are sold in pairs you can test to see how much drop front and back you can get. I do recall I only decided to buying the 9k 150mm once i saw they had it (gotta keep checking or maybe just ask them), i bought a pair of 8k 175mm (7") to test.
I only went with the 9k, because i calculated it would allow me to lower a bit more (i forgot the number) and still be at the same height compared to 4k when fully loaded with passengers. Be warned that 9k, is pretty stiff.
I only went with the 9k, because i calculated it would allow me to lower a bit more (i forgot the number) and still be at the same height compared to 4k when fully loaded with passengers. Be warned that 9k, is pretty stiff.
@ezhacker1 regarding your post about shortening rear shocks for preload/length. If you have the shock too long and once lowered at ride height the inner valve pushes down pretty far towards the bottom of the inner tube, wouldnt you call that preload too?
Also if the shock is set so long that once the car is lowered to its static height if the valve is resting agains the inside of the bottom of the tube, wouldnt that hold the car up anyways? in that case, shortening the shock would allow the valve to move back up the inner tube at static height and then that would allow the car to settle down more.
just like discussing these things with other suspension experts lol
Also if the shock is set so long that once the car is lowered to its static height if the valve is resting agains the inside of the bottom of the tube, wouldnt that hold the car up anyways? in that case, shortening the shock would allow the valve to move back up the inner tube at static height and then that would allow the car to settle down more.
just like discussing these things with other suspension experts lol
Tested the cars ABS today. Yup, as of right now no ABS.. Lol. I gotta figure out what happened to that and the Vehicle Stability Control already. Those lights on the dash are not fun to look at. A friend of mine told me that if we did stretch the wires out on accident it will be costly to replace.. *sigh*
lol, you don't needs ABS or VSC anyway 😛 😉Originally Posted by TerenceCruz ↑Tested the cars ABS today. Yup, as of right now no ABS.. Lol. I gotta figure out what happened to that and the Vehicle Stability Control already. Those lights on the dash are not fun to look at. A friend of mine told me that if we did stretch the wires out on accident it will be costly to replace.. *sigh*
i read and re-read this a few times. LOL gets confusing. Front is easy to visualize how the whole system works, rear takes alot of my brain cells HAHA.Originally Posted by 1.5 ↑@ezhacker1 regarding your post about shortening rear shocks for preload/length. If you have the shock too long and once lowered at ride height the inner valve pushes down pretty far towards the bottom of the inner tube, wouldnt you call that preload too?
Also if the shock is set so long that once the car is lowered to its static height if the valve is resting agains the inside of the bottom of the tube, wouldnt that hold the car up anyways? in that case, shortening the shock would allow the valve to move back up the inner tube at static height and then that would allow the car to settle down more.
just like discussing these things with other suspension experts lol
This is just my understanding of how suspension works.
The front shocks have preload abililty which is just pre compressing the spring even before the car is on the ground, but that spring will push against the shock hat, tugging on the shaft 🤣
The rear struts need to be set up in such a way at static load with wheels on ground that the shaft has enough travel both up and down without bottoming out. I measured static shaft length, compared that to how much shaft is left with car on ground, and calculate at max load how much more the shaft will travel. Then i adjust the strut height accordingly, making sure that with wheels off ground the spring and perches don't fall out.
right, so in the rear you have some preload to keep the spring taught even with wheels in the air, mine i have way longer. I have never bottomed mine out, when they were short I topped them out all the time.
I was considering shortening the shock to see if it was holding me up at all, but with my recent mods my fitment is perfect so idc now haha
I was considering shortening the shock to see if it was holding me up at all, but with my recent mods my fitment is perfect so idc now haha
Hahah maaan, I'd like to keep those features though 🙁Originally Posted by Kaotic Lazagna ↑lol, you don't needs ABS or VSC anyway 😛 😉
Originally Posted by ezhacker1 ↑i read and re-read this a few times. LOL gets confusing. Front is easy to visualize how the whole system works, rear takes alot of my brain cells HAHA.
This is just my understanding of how suspension works.
The front shocks have preload abililty which is just pre compressing the spring even before the car is on the ground, but that spring will push against the shock hat, tugging on the shaft 🤣
The rear struts need to be set up in such a way at static load with wheels on ground that the shaft has enough travel both up and down without bottoming out. I measured static shaft length, compared that to how much shaft is left with car on ground, and calculate at max load how much more the shaft will travel. Then i adjust the strut height accordingly, making sure that with wheels off ground the spring and perches don't fall out.
Originally Posted by 1.5 ↑right, so in the rear you have some preload to keep the spring taught even with wheels in the air, mine i have way longer. I have never bottomed mine out, when they were short I topped them out all the time.
I was considering shortening the shock to see if it was holding me up at all, but with my recent mods my fitment is perfect so idc now haha
Haha I'm still trying to absorb all of this since I consider myself a noob when it comes to the way the coils can be adjusted. When I lift my car from the rear the springs just fall out.. Haha. The weight of the car is keeping them in place when it's on the ground.Originally Posted by TerenceCruz ↑Hahah maaan, I'd like to keep those features though 🙁
Well to a certain extent the strut height should keep the spring assembly from falling out, but if you take out perches rings, or swap to shorter spring length then depends.
Ill look at your car at the coming up meet.
Ill look at your car at the coming up meet.
Sounds good man. Thank you. You have an 09+ Yaris right? So you have ABS and VSC?Originally Posted by ezhacker1 ↑Well to a certain extent the strut height should keep the spring assembly from falling out, but if you take out perches rings, or swap to shorter spring length then depends.
Ill look at your car at the coming up meet.
ABS yes, VSC no.
Ahhh okay. The ABS light didn't give you any problems at all when you installed the coilovers? Did you unplug the sensors or anything during the install? I'm just trying to figure out what may have caused the lights to go off cause I thought we did a good job about avoiding messing up the wiring.Originally Posted by ezhacker1 ↑ABS yes, VSC no.
So a friend of mine told me the reason why my ABS and VSC lights stay on now is because the car is too low for the sensors to get an accurate reading. I have to get "extensions" for the sensors supposedly. Still gotta do some hw but what he says does make sense.
haha nice
Haha it sucks though man, I looked online and I can't really find any info about the wire "extensions" 😕Originally Posted by 1.5 ↑haha nice
put some electrical tape over the warning lights
Originally Posted by 1.5 ↑put some electrical tape over the warning lights
+1 hahaha or open the cluster and smash the bulb
lol they dont do anything its a yaris it can only get so much out of control lol
Haha your car is "Dumped" get it the dumpster
but in all seriousness, really nice shots man
but in all seriousness, really nice shots man
Originally Posted by 1.5 ↑Haha your car is "Dumped" get it the dumpster
but in all seriousness, really nice shots man
Lol yeah! I like the dumpster shot, maybe park in the middle and angle it a bit, then booooom! Plus add some hot chic :)))) cover photo! Haha
Only if she is inside the dumpster rubbing garbage on herself in slow motion!!
Originally Posted by 1.5 ↑Haha your car is "Dumped" get it the dumpster
but in all seriousness, really nice shots man
Originally Posted by dumbo0 ↑Lol yeah! I like the dumpster shot, maybe park in the middle and angle it a bit, then booooom! Plus add some hot chic :)))) cover photo! Haha
Lmao! Thanks fellas. I made a wrong turn into a parking lot then I saw this spot. So I figured I might as well! Haha.😁Originally Posted by 1.5 ↑Only if she is inside the dumpster rubbing garbage on herself in slow motion!!
impromptu those are the best lol
Seriously though man lolOriginally Posted by 1.5 ↑impromptu those are the best lol
Slowly but surely guys 😁 I'm in love. 16x8.5 +25
Picture not included in this copy
Picture not included in this copy
Annnd.. A random shots of my Vitz. Gona enjoy rolling on the steelies with hubcaps for a while until I get some money together for tires. I'm thinking 195/45 or 205/45..
Picture not included in this copy
Picture not included in this copy
Nice... how much lip are those? I truly like 16s more than 17s, but iv never had 16s before tho i think it first nicer.
I gotta do a build thread haha. show off my bumpers lol. Gotta get my lazy self to do a photo shoot tho.
I gotta do a build thread haha. show off my bumpers lol. Gotta get my lazy self to do a photo shoot tho.
Thanks man haha it has a 1.5 inch lip. I figured that will keep me happy for now haha and I felt like 16s were the perfect size for me, not too big not too small. But yeah man, you gotta show off your car, especially with those bumpers and the works on there lol.Originally Posted by ezhacker1 ↑Nice... how much lip are those? I truly like 16s more than 17s, but iv never had 16s before tho i think it first nicer.
I gotta do a build thread haha. show off my bumpers lol. Gotta get my lazy self to do a photo shoot tho.
nice. i would have gotten the xxr 526 17x9 +35 But yeah VS-XX is better but i need more lip! lol. it'll cost as much as getting a second set of wheels/tires to relip them :( So i might just get a second set for lip haha.