LoL i appreciate it man
My Build Thread
650 posts · 141,009 views · page 5 of 13
Replies continued
Got some beer today
Picture not included in this copy
Wait a minute....
Picture not included in this copy
Picture not included in this copy
Wait a minute....
Picture not included in this copy
Running into some problems during install. I am so uneducated when it comes to wiring and need some one to help point me in the right direction.
I am trying to install my AEM wideband A/F gauge and am able to get it wired up and running but I think I am doing it wrong as I am reading extremely lean and getting CEL's.
I was under the impression that the stock a/f sensor would be pulled and replaced with the AEM. However the AEM then would only plug from the sensor into the gauge and then the gauge into a power/ground source. I believe this is causing the lean/cel issue as the ecu is no longer receiving a signal from the sensor. I have been told that I most likely need to have a seperate bung welded on that I can have the AEM wired to and leave the current stock one in place. Is this correct?
This is what my setup looks like.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
I also have an aem fic with a custom harness that I am going to install so can I just wire the gauge to the piggyback or is the stock sensor not going to provide the accurate readings for the AEM wideband?
I am trying to install my AEM wideband A/F gauge and am able to get it wired up and running but I think I am doing it wrong as I am reading extremely lean and getting CEL's.
I was under the impression that the stock a/f sensor would be pulled and replaced with the AEM. However the AEM then would only plug from the sensor into the gauge and then the gauge into a power/ground source. I believe this is causing the lean/cel issue as the ecu is no longer receiving a signal from the sensor. I have been told that I most likely need to have a seperate bung welded on that I can have the AEM wired to and leave the current stock one in place. Is this correct?
This is what my setup looks like.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
I also have an aem fic with a custom harness that I am going to install so can I just wire the gauge to the piggyback or is the stock sensor not going to provide the accurate readings for the AEM wideband?
This video shows how the gauge keeps searching and records a very lean mixture
http://s23.photobucket.com/user/Mist...75928.mp4.html
http://s23.photobucket.com/user/Mist...75928.mp4.html
you need the stock one in place so when you tune the FIC you can get the right readings. the car will not run right without it in there.
OK so a new bung it is?
So I unplug the battery, remove the aem equipment, put the stock a/f sensor back, plug the battery back in, and now its stalling and bogging down and idling extremely low but there is no CEL?
Are you sure you don't have a vacuum/exhaust leak? Also, give the ecu a few minutes to relearn short term fuel trims when you reconnect the battery.Originally Posted by 1.5 ↑So I unplug the battery, remove the aem equipment, put the stock a/f sensor back, plug the battery back in, and now its stalling and bogging down and idling extremely low but there is no CEL?
Assuming a stock fuel system, the car will run normally (maybe slightly lean, and will throw a P0031 code) with the front O2 sensor removed.
How are you planning on tuning? Open or closed loop?
I never had any leak before and I'm still NA this was to prepare for my s/c. When the front sensor was replaced with the aem yes it gave me that lean code. Now that everything is back to stock there is no code but that sputtering and stalling. Can I drive it like that? Will the ecu relearn with the car off or does the ignition need to be on?
The car needs to be running to receive feedback from the O2 sensors. You could try driving the car as is and seeing if it corrects itself, but I'm doubtful.
Do you have a code reader? Being able to read the fuel trims would be pretty beneficial also. Since you're planning on installing a Blitz, I'd recommend x10000000 to go out and buy an OBDII scanner.
Do you have a code reader? Being able to read the fuel trims would be pretty beneficial also. Since you're planning on installing a Blitz, I'd recommend x10000000 to go out and buy an OBDII scanner.
I do have one that's how I've been reading the codes this far but again there is no CEL anymore the car is just sputtering, bogging, and stalling. It sounds like I just cammed it lol If it needs to be on then I guess I'm gonna go through my morning commute and hope that does the trick. Ill see what readings I get for a/f now.
Try disconnecting everything again. disconnect the battery and ecu just for shits and giggles. take a shower and come back. double check your connections. plug it back in. go make a sandwich, or wait 5 mins. then start the car again. just let it idle for 10-15 mins. Drive it around the block. drive it easy, dont go crazy. Then after that, go crazy. floor it a couple times. see if this helps
So this morning I had to come to work so I fired it up and again the bogging/stalling happens. I cant let it sit and idle because within seconds it stalls out, I have to keep gassing it. As I drive to work I notice slight improvements. The idle still gets super low, down to ~500 at times but then it spikes back up to ~1300 sometimes and it no longer stalls but the idle fluctuates between those points.
This screen shot shows my readings at idle once everything leveled off and stopped stalling out. Again the rpms still go as low as 500 and as high as 1300 bouncing around between those points but at least no stall outs.
Picture not included in this copy
This shot shows my readings under some heavier load
Picture not included in this copy
As stated before my car displays no codes however I decided to pull the log anyways and this is what I find. How the hell are cylinders misfiring now? I never touched them. Fuel line isnt kinked or anything.
Picture not included in this copy
This screen shot shows my readings at idle once everything leveled off and stopped stalling out. Again the rpms still go as low as 500 and as high as 1300 bouncing around between those points but at least no stall outs.
Picture not included in this copy
This shot shows my readings under some heavier load
Picture not included in this copy
As stated before my car displays no codes however I decided to pull the log anyways and this is what I find. How the hell are cylinders misfiring now? I never touched them. Fuel line isnt kinked or anything.
Picture not included in this copy
3 attachments not included in this copy
I hate to sound redundant but... You almost certainly have a vacuum leak if you're misfiring on multiple cylinders and throwing P0171. Further, you're going to run lean under idle and have less issues while cruising. What are your vacuum readings while the engine is bogging?
If you have an in with a mechanic, try having them smoke test your intake. I'm sure the problem will pop up pretty quickly.
The problem could also be on the exhaust side, since that's where you were working more recently... If you have fresh air getting into the exhaust, it will also cause the O2 sensor to read leaner than normal. If you took the header off recently, did you remember to put the donut gasket back?
If you have an in with a mechanic, try having them smoke test your intake. I'm sure the problem will pop up pretty quickly.
The problem could also be on the exhaust side, since that's where you were working more recently... If you have fresh air getting into the exhaust, it will also cause the O2 sensor to read leaner than normal. If you took the header off recently, did you remember to put the donut gasket back?
under idle while the engine is stuttering it reads ~20-23 in/Hg
I havn't messed with the header since install like a year ago. The gasket is there yes.
I did remove the intake air filter yesterday but Im sure its on securely, Ill double check it.
I havn't messed with the header since install like a year ago. The gasket is there yes.
I did remove the intake air filter yesterday but Im sure its on securely, Ill double check it.
Just went out to the car and unplugged the battery again, gonna let it sit for a long time this time. I did also notice the tinniest gap between air filter/tubing so i repositioned it and tightened it down. Let's see...
Battery was pulled for 2 hours and tightened down the intake but same problem when I fired it up again, but the stalling out has started back up. So it wont idle again unless I give it gas
You didn't run the car at any point with the O2 sensor in still, but unplugged, did you? Doing so will ruin the sensor VERY quickly. Out of curiosity, how did you wire up the wideband? Anything else you messed with recently?
Step by step what I did is:
-unplug battery
-unplug stock a/f sensor
-cover stock sensor with supplied protector from AEM and place gently on pass seat
-screw in AEM wideband sensor and plug into AEM gauge and wired gauge up to power/ground
-reconnect battery
-fired up car and immediately saw what I was doing wrong, the car threw a lean code and the AEM a/f gauge showed the ratio spiking all the way up to 19s
-Realized that I was causing a problem by removing the stock sensor and leaving the ecu
harness unplugged
-unplugged battery
-removed all the AEM equipment and replaced the stock sensor
-plugged stock sensor back in
-plugged battery back up
-fired it up and it started bogging and misfiring and stalling out
-unplug battery
-unplug stock a/f sensor
-cover stock sensor with supplied protector from AEM and place gently on pass seat
-screw in AEM wideband sensor and plug into AEM gauge and wired gauge up to power/ground
-reconnect battery
-fired up car and immediately saw what I was doing wrong, the car threw a lean code and the AEM a/f gauge showed the ratio spiking all the way up to 19s
-Realized that I was causing a problem by removing the stock sensor and leaving the ecu
harness unplugged
-unplugged battery
-removed all the AEM equipment and replaced the stock sensor
-plugged stock sensor back in
-plugged battery back up
-fired it up and it started bogging and misfiring and stalling out
So on my commute home finally my CEL came on and these are the codes now:
Picture not included in this copy
Its no longer reading cylinder 1 or 3 misfires like before but it still sputters. It also doesn't fluctuate at idle as much either. It kinda stays around 950-1100 with AC on and around 550-700 with AC off.
Here are my readings at idle
Picture not included in this copy
Picture not included in this copy
Its no longer reading cylinder 1 or 3 misfires like before but it still sputters. It also doesn't fluctuate at idle as much either. It kinda stays around 950-1100 with AC on and around 550-700 with AC off.
Here are my readings at idle
Picture not included in this copy
P0101 is the code that everyone throws when they install a new intake improperly/seat the maf improperly... Unless you actually have maf problems, which is unlikely. I'd try reconnecting the maf connector just in case. I know you haven't really touched anything on the intake side, but I'm still leaning towards a leak, and P0101 further supports that idea.
Since I didn't really mess with much where should I look for the vacuum leak? Is there a test I can conduct myself similar to the smoke test. I know you boosted guys use compressed air to test seals. How detrimemtal to my engines life is daily driving it right now?
It really depends on how bad you're misfiring. It seems like during normal driving it isn't too bad, which suggests a fairly small leak since you're only seeing problems during idle. Obviously, it should still be fixed asap.
You could build a boost leak tester which would serve the same purpose to find a vacuum leak. You can get all the parts you need from Home Depot on the cheap. I'll see if I can find the guide I used to build mine...
Smoke machines are quicker and more thorough though.
You could build a boost leak tester which would serve the same purpose to find a vacuum leak. You can get all the parts you need from Home Depot on the cheap. I'll see if I can find the guide I used to build mine...
Smoke machines are quicker and more thorough though.
Ok thanks! Is a "smoke" test common practice? I typically do my maint at my boys shop which is a full service shop but it's no toyota or aftermarket installer, I just dont know if he would have the means to do that.
Yes, very common. That should be the first step to diagnose a vacuum leak by any competent mechanic. Basically they put a plug in your PCV port on the intake and throw a bunch of smoke in the intake. Smoke will come out of any leaks that you may have.
ok Ill see if I can take it over to him. Thanks for all your help man.
Great success!!! I really was sick of my idle/lean issues so I decided to take apart my almost entire breathing cycle and reinstall and found a couple pain points. Removed the air intake and throttle body, took off my header, removed and reinstalled the a/f sensor and this is what I found:
-the coupler attaching piping to TB had a large crack running down each side
-the vacuum line had a hole in the portion facing downward
-cleaned a ton of soot off the header/exhaust donut
-Extremely tight A/f (stock one I was able to unscrew by hand)
After replacing the coupler and cutting myself a new vacuum line, replacing everything, cleaning the donut, and loosening the sensor, I fire it up and let it idle. Immediately I notice how smooth it runs. Pull my OBDII reader and clear my CEL. Re run the code pull and get the always delightful "there are no fault codes stored on the ecu" message. Snap shot some of my readings and notice revs right where I want them and the afr back to ~13s-14s. Thanks again to Focus and Derrick you guys convinced me not to give up that it was a vacuum leak and I seem to have found it. Not sure why it never popped up til I started messing with the a/f sensor but I am much happier lol.
Picture not included in this copy
-the coupler attaching piping to TB had a large crack running down each side
-the vacuum line had a hole in the portion facing downward
-cleaned a ton of soot off the header/exhaust donut
-Extremely tight A/f (stock one I was able to unscrew by hand)
After replacing the coupler and cutting myself a new vacuum line, replacing everything, cleaning the donut, and loosening the sensor, I fire it up and let it idle. Immediately I notice how smooth it runs. Pull my OBDII reader and clear my CEL. Re run the code pull and get the always delightful "there are no fault codes stored on the ecu" message. Snap shot some of my readings and notice revs right where I want them and the afr back to ~13s-14s. Thanks again to Focus and Derrick you guys convinced me not to give up that it was a vacuum leak and I seem to have found it. Not sure why it never popped up til I started messing with the a/f sensor but I am much happier lol.
Picture not included in this copy
1 attachment not included in this copy
Hell yeah!!! I was talking to my boy Eddy at work about that and he said it might of been a problem with the Throttle Body or the case of the leakage. Awesome as hell you got the problem solved!!
Nice. Always great to see a problem solved. 👍
Yea its hard to say since i did like 4 different things, exactly what the problem was but I am just happy its back to normal. Today again on my morning commute everything ran fine.Originally Posted by HANZO_187 ↑Hell yeah!!! I was talking to my boy Eddy at work about that and he said it might of been a problem with the Throttle Body or the case of the leakage. Awesome as hell you got the problem solved!!
Thanks again man.Originally Posted by Focus_Sh1ft ↑Nice. Always great to see a problem solved. 👍
Cars do that.. Once you start playing with thier insides they get all pissy and start making leaks where you never touched before just to piss you off.
For real duuude lol.
It was my car telling me "F*** the management give me more AIR!!!!"
It was my car telling me "F*** the management give me more AIR!!!!"
I want more , I want more , we want more ...just like that little girl on tv commercial ..lol
hahaha thats so funny I referenced that same commercial for something similar this morning lol
Bored so pulled out all my wheel parts and mocked up what I plan to build. I was actually torn between two options of sizing/offset but have made up my mind now My setup will look as follows
Front: 16x8.5 +17 w/ 3mm spacer and 195/45/16
Rear: 16x9.5 +17 optional 3mm spacer and 195/45/16
Anyways on to the pics
16x9.5 +17
Picture not included in this copy
Picture not included in this copy
Front: 16x8.5 +17 w/ 3mm spacer and 195/45/16
Rear: 16x9.5 +17 optional 3mm spacer and 195/45/16
Anyways on to the pics
16x9.5 +17
Picture not included in this copy
Picture not included in this copy
2 attachments not included in this copy
gezus that is a wide rim with crazy offset for a yaris
^ its the only way I know lol
The xxrs I had before were 17x9.75 +25 so it is close
The xxrs I had before were 17x9.75 +25 so it is close
Coming along good Phil !!
To and from Rotiform... I hope they are back soon
Picture not included in this copy
Picture not included in this copy
1 attachment not included in this copy
Check out this short video feature of my Yaris
https://www.facebook.com/SouthernStreetsEmpire
https://vimeo.com/67176893
https://www.facebook.com/SouthernStreetsEmpire
https://vimeo.com/67176893
Gangsta!!
lol you know im a G
That video edit was awesome, music was smooth as the car. I can't wait for the roll out...
i cant wait to see this set up phil! what are you having done at rotiform?
Redrill, fill, and maybe a powdercoat if I can afford to do it all together.
It's finally done! Too bad it won't be going on my car anymore...
Picture not included in this copy
you can buy it here
FS: It's Back!
Picture not included in this copy
you can buy it here
FS: It's Back!
1 attachment not included in this copy
This came in yesterday too
Picture not included in this copy
Picture not included in this copy
1 attachment not included in this copy
Beautiful!Originally Posted by 1.5 ↑It's finally done! Too bad it won't be going on my car anymore...
Attachment 51106
you can buy it here
FS: It's Back!
Picture not included in this copy
HAHAHAHA I love that pic
Steering wheel done! Got a few questions and I dont think it's 100% straight but tweaking will take care of that, I love the look, stay tuned for pics