oh yea, the valvesprings and retainers are Supertech..... meant for a Scion tC. worked great.
Going for broke
143 posts · 44,221 views · page 3 of 3
Replies continued
I'm amazed that all the valve springs between all these motors are the same size
omg you are my boost role model. I think this was mentioned in another thread, I know you were running a stock motor except the rods. Is the valve springs the only thing you changed or did you upgrade the pistons also this round?
I imagine he had no choice but to get new pistons. He showed photos of the damage in his other thread titled "Finally, my motor went". Number 4 piston was damaged previously from a destroyed spark plug, and number 3 took some serious pounding when the valve dropped. Just wondering what piston set he went with and if there was any damage to number 3 rod.
Same bottom end, pistons and all. Just a replacement head decked and supertech valve springs. I was amazed that the motor pulls 20inhg vacumm after seeing my clyinder walls scored.
Amazing! Any additional support to the main bearings? Curious to know who's rods your running and if the crank is stock.
no main bearings support other than stock main bearing caps. Crower rods, CP pistons, Supertech valvesprings are only internal upgrades. Stock headbolts, stock intake manifold, stock throttle body.Originally Posted by Toy_Yoda ↑Amazing! Any additional support to the main bearings? Curious to know who's rods your running and if the crank is stock.
My build focuses on trying to achieve good numbers and reliability without spending tons of $. xbgod boasts about his $40k motor build, and is producing the same numbers without spray. 90% effect with 10% of the effort (and $) is what I aim for. Don't get me wrong, I use all good parts. Haltec and return fuel sytem are running the show.
^ Amen. I run stock crank/bearings/cams/valves as well.
A truly inspiring and smart build! Nice to know that other than rods and pistons these little engines are so robust. The plans I have for my XB after next smog inspection February is a Blitz supercharger and piggyback fuel management on stock internals. While I'm enjoying the modest gains I'll see from 6 lbs. boost, I plan to build another engine that can withstand the higher boost I can get from a turbo. I'll be sure to take a clue from you and change out the valve springs once the rev limiter is history. Looking forward to seeing the dyno pull once you get a new turbo sorted out and if it's reliable as the last build.
yes, Obviously he had to get new pistons. I read that thread also being I knew about the rods. Hence why I asked if there was any other upgrades he did besides the valve springs. Like you I was asking the same question if he upgraded the pistons but in a more broad approach to include other parts of the motor.Originally Posted by Toy_Yoda ↑I imagine he had no choice but to get new pistons. He showed photos of the damage in his other thread titled "Finally, my motor went". Number 4 piston was damaged previously from a destroyed spark plug, and number 3 took some serious pounding when the valve dropped. Just wondering what piston set he went with and if there was any damage to number 3 rod.
I found out today why my 6 month old turbo failed. The oil feed line restrictor had a peice of debris in it, which cut off oil flow tremendously. I did an oil change days after installing the head, but that was probably too late. Also, I have my oil feed line going to a oil filter sandwich adapter, which is pre filtered oil. So lesson learned, turbo oil supply should always come from the block.
Hey just an update... Im going to swing for a gt3076 this winter, but in the mean time I installed a $200 cheap turbo of similar dimension to my Garrett t3/4 50 trim which just failed. Im VERY AGAINST knock-off parts, but Im committed to attending a time attack this weekend. Im running 26psi (4psi less) because I don't want to go too hard on this turbo. Numbers are good , and notice that the car makes power all the way to 8000rpm! The supertech valve springs did wonders, those along with the hayabusa style turbo manifold allowed that to happen. Still stock head, valves, cams, intake manifold , throttle body.
1 attachment not included in this copy
Nice! Any pics of the Hayabusa style plumbed in?
What failed? Bearings?
oil starvation, do to a piece of debris in feed line.Originally Posted by Bluevitz-rs ↑What failed? Bearings?
in this very thread, few pages backOriginally Posted by CTScott ↑Nice! Any pics of the Hayabusa style plumbed in?
SWEET. great numbers
update: Did my first track event with this much power, I attended Grip Fest which is a time attack. First lap, 3rd gear broke. Our transmissions cannot handle over 300whp doing anything other than drag runs, and daily driving. This was a downer because I drove from 4 hours away to compete , and I didn't think I would be able to make it home ( transmission sounded like ice in a blender ).
Call me crazy, but to put myself in a better mood ...... I decided to make a few runs anyway, skipping 3rd gear. I turned my boost controller off running about 230whp, And posted the 3rd fastest time of the day overall! What an adventure ! On top of that, I was able to make it back to the hotel 70miles away.
The next day was the final autocross for the year, a series which I have been competing in for points. I was leading my class for points, but if I didn't compete I would be handing over the lead. So what did I do? I autocrossed my broken car, and secured the class win. My transmission was SO BAD, that it stopped my car from rolling several times as I was driving through the pits.
Next mission was to make it back home, 120 miles away........... By some miracle , I made it.
Video of the weekend coming soon.
Call me crazy, but to put myself in a better mood ...... I decided to make a few runs anyway, skipping 3rd gear. I turned my boost controller off running about 230whp, And posted the 3rd fastest time of the day overall! What an adventure ! On top of that, I was able to make it back to the hotel 70miles away.
The next day was the final autocross for the year, a series which I have been competing in for points. I was leading my class for points, but if I didn't compete I would be handing over the lead. So what did I do? I autocrossed my broken car, and secured the class win. My transmission was SO BAD, that it stopped my car from rolling several times as I was driving through the pits.
Next mission was to make it back home, 120 miles away........... By some miracle , I made it.
Video of the weekend coming soon.
All I can say is , WOW!
So have you decided on what way you're going to with a new transmission? I vote C160.
So have you decided on what way you're going to with a new transmission? I vote C160.
My next course of action is to remove to LSD from the broken transmission , hopefully it is ok. I have my original transmission sitting on a shelf, and it is good. The broken one had taller/Yaris gears. I would like to a transmission cooler setup, just like our time attack tC. Basically takes the oil from the drain plug, pumps (elecric pump) oil through cooler , then back through oil squirters tapped into trans casing aimed at each gear.
Now this is quite something. Congratulations! Its a challenge to keep moving in such circumstances.
What gearbox [the one which broke] were you using? C56?
I had some issues lately when i had an autocross event. Gear selector cables broke,managed to change them and then radiator started leaking,managed to fix that too [a friend who repairs radiators for a living was around] and then i won :)
What gearbox [the one which broke] were you using? C56?
I had some issues lately when i had an autocross event. Gear selector cables broke,managed to change them and then radiator started leaking,managed to fix that too [a friend who repairs radiators for a living was around] and then i won :)
I may have a spare Yaris FD if you need a set.Originally Posted by Blown_xa ↑My next course of action is to remove to LSD from the broken transmission , hopefully it is ok. I have my original transmission sitting on a shelf, and it is good. The broken one had taller/Yaris gears. I would like to a transmission cooler setup, just like our time attack tC. Basically takes the oil from the drain plug, pumps (elecric pump) oil through cooler , then back through oil squirters tapped into trans casing aimed at each gear.
^ haha, me too.
Our transmissions cannot handle over 300whp doing anything other than drag runs, and daily driving.well, knock on wood, but mine has been fine for a handful of track days.
You lucked out I guess, this is the first transmission failure in the life of this car which isn't too bad I guess ( considering ). I grew used to the tall Yaris gears, however now that I have a high rev limit, I may be better off going back to my xA gearing . I am really hoping my Kaaz lsd is ok. Does anyone know detailed info on the Kaaz gearset? Are they stronger? I know the ratios are closer..... but I would want that set more for a strength upgrade.Originally Posted by cali yaris ↑^ haha, me too.
well, knock on wood, but mine has been fine for a handful of track days.
I have been told that this is the only option that we have with the C50. The only other real option would be to upgrade to a TRD Vitz RS Turbo Transmission however from what I have found from research the only way to get that is to purchase a half cut of a TRD Vitz however also on the same token I have read that they are rare. I will be very concerned myself once my engine upgrades are complete on the tranny holding up, but then again I won't be overly aggressive with it since I am do straight line racing so the stock one might hold up, but I am not holding my breath. I have already burned through 1 tranny and that is with only having 50k stock and 20k boosted (7-9psi) miles on it.Originally Posted by Blown_xa ↑You lucked out I guess, this is the first transmission failure in the life of this car which isn't too bad I guess ( considering ). I grew used to the tall Yaris gears, however now that I have a high rev limit, I may be better off going back to my xA gearing . I am really hoping my Kaaz lsd is ok. Does anyone know detailed info on the Kaaz gearset? Are they stronger? I know the ratios are closer..... but I would want that set more for a strength upgrade.
The C56 transmission from the Vitz RS is quite strong. The same transmission can be found on the Toyota Starlet Glanza [two door starlet with the 4efte]. But they have a limit too,around 300whp max [dont remember the torque figures] and they are known for 3rd synchro failure on high powered set ups.
Visit Monkeywrenchracing.com they have tons of transmission parts. Mostly for the 6 speed but they might have others too.
found time to take the transmission out and apart to remove the LSD. This picture shows 3rd gear with no teeth. Going to order some new seals for my original transmission, and transfer the LSD. Going back to the shorter gears since rev limit is 8k now.
1 attachment not included in this copy
Wow! I've never seen that before. Measure the width of the gears in both transmissions. Curious if one has wider gears than the other. I'm pretty sure my C160's gears are wider than the C150 stock gears. I'd have to check my old build thread.
widths are the same, in fact, they are the same as the Scion tC as well .Originally Posted by Bluevitz-rs ↑Wow! I've never seen that before. Measure the width of the gears in both transmissions. Curious if one has wider gears than the other. I'm pretty sure my C160's gears are wider than the C150 stock gears. I'd have to check my old build thread.
That's crazy you managed to strip the teeth of then. Maybe I'm thinking of a C54 from the celica. I know one of the C series transmissions has wider gears in it.
I took a picture comparing the yaris output gear shaft (right) to a tC output gear shaft (left) . Ignore the top/4th gear on the tC shaft, it is a prototype gear we are testing and is odviously beefier. Look how similar the gears are. tC transmissions are known to shear 4th gear at / above 400whp.
1 attachment not included in this copy
any further updates? I sent you a PM Justin btw if you missed it.
Next week I requested off to get the car back together, Im glad because I just want it up and running again.
So are you just going to put the stock gearbox back in?
yes. I contacted Kaaz about their gear set, and there is no guarantee that they will hold the power. That isn't a $2000 gamble Im willing to take. I am doing a cooler setup however.Originally Posted by Bluevitz-rs ↑So are you just going to put the stock gearbox back in?
This year Im focusing more on overall performance and reliability. Just got a new set of wheels in, fitting 275's up front. Then Im doing an oil cooler setup and koyo radiator along with the trans cooler.
Are you going to detune the power a bit for a flatter power band too?
I PM'd you. Car is back to 100%, improvements being made before this upcoming season... Check out my latest update under wheel and tire threads.Originally Posted by fnkngrv ↑any further updates? I sent you a PM Justin btw if you missed it.
Im going to run on wastegate pressure (230-250whp) unless Im being edged off the podium in a time trial 🙂Originally Posted by Bluevitz-rs ↑Are you going to detune the power a bit for a flatter power band too?
It"s been a while, here are some updates... Springtime I attended a time trial, at that time trial I was sitting in second place ioverall after a few sessions so I decided to run full boost. My motor finally had enough. The piston which was scored a long time ago (cylinder 4) detonated and I melted a piston. I did grab second place though, so that day was still a success lol. I since built another motor and had it running in time for the fall Gripfest ( time trial). I did not get my injectors flow tested in time so I ran low boost, around 260whp but with great success. I edged out the previous winner, and did so in the rain. This was awesome because he was in an STI, so no more excuses that awd is dominant in the rain 🙂 . I was only beat by our own shop time attack tC ( 2008-2009 mod fwd Redline Time Attack champ), and a Formula Ford. Yes, Gripfest doesn't have classes, it's run what you brung.
I also squeezed in a few autocrosses before the race season ended, with great results. Ive been dominating SMF SCCA class, and almost grabbed FTD overall in a couple events. Im still getting used to the massive grip over 275 width Hossiers up front. Here are a few pictures
I also squeezed in a few autocrosses before the race season ended, with great results. Ive been dominating SMF SCCA class, and almost grabbed FTD overall in a couple events. Im still getting used to the massive grip over 275 width Hossiers up front. Here are a few pictures
5 attachments not included in this copy
Thats fucking awesome... I will be moving to smf also soonish.. You are an amazing tuner/mechanic. good luck next year..
Damn Justin that's so sick. 🙇🙇🙇🙇🙇🙌Originally Posted by Blown_xa ↑It"s been a while, here are some updates... Springtime I attended a time trial, at that time trial I was sitting in second place ioverall after a few sessions so I decided to run full boost. My motor finally had enough. The piston which was scored a long time ago (cylinder 4) detonated and I melted a piston. I did grab second place though, so that day was still a success lol. I since built another motor and had it running in time for the fall Gripfest ( time trial). I did not get my injectors flow tested in time so I ran low boost, around 260whp but with great success. I edged out the previous winner, and did so in the rain. This was awesome because he was in an STI, so no more excuses that awd is dominant in the rain 🙂 . I was only beat by our own shop time attack tC ( 2008-2009 mod fwd Redline Time Attack champ), and a Formula Ford. Yes, Gripfest doesn't have classes, it's run what you brung.
I also squeezed in a few autocrosses before the race season ended, with great results. Ive been dominating SMF SCCA class, and almost grabbed FTD overall in a couple events. Im still getting used to the massive grip over 275 width Hossiers up front. Here are a few pictures
That pic of you entering the slalom gives me chills lol