Yarisworld Archive

prius piston swap

100 posts · 60,760 views · page 1 of 2

Nanoss22Original postPuerto rico · Jul 18, 2012#1
Sorry for the delay... just done it today and it works perfectly no mods requiered now some good breaking and dyno cooming soon...

10 attachments not included in this copy

Replies 99

GolddeenohColumbia, SC · Jul 18, 2012#2
how much driving have you done and can you feel a difference?
ViperoniBrampton, ON · Jul 19, 2012#3
Is any tuning required, and is 91 octane gas required?

Can't wait to see the numbers! :)
malibuguyWestminster, MD · Jul 19, 2012#4
finally someone is straight up doing it!
Nanoss22Thread starterPuerto rico · Jul 19, 2012#5
No modification needed just 91 gas from now foward i have a apex safc for the air fuel ratio and yes i can tell it feel diferent
1.5Tampa · Jul 19, 2012#6
how much of a difference? Any dynos? Why 91 required?
Flipper_1938Kentucky · Jul 19, 2012#7
Originally Posted by 1.5 ↑
how much of a difference? Any dynos? Why 91 required?
Because his compression ratio is now close to 13:1 !!!

I too am anxious to see how it does. Are you going to run the stock camshafts?
blacksandiegovitzJust chillin' out brah ! · Jul 19, 2012#8
Killer ! Did you use the yaris rods or the prius ones ? Also what apexi safc are you using , afc2 or the neo ?
Nanoss22Thread starterPuerto rico · Jul 19, 2012#9
The safc2 i just install the pistons yesterday now i am in breaking mode... I use the 1nz fe rods all internals are original i have some mods like 1zz trhtle ebay intake with velocity costum echo header 2" catless ending with magnaflow freeflow 2 1/4 exhaust the last time i did the dyno pull without fixing the afr 111whp if you guys are excited i am crazy to tune it to see the gains... the thing is that i have a lot of mods to get done to get the max hp so they are cooming soon
fast2882Indonesia · Jul 25, 2012#10
Hi Guys, i am from Jakarta Indonesia, and really interested with this thread. Wow... finally, 1nz-fxe piston in 1nz-fe engine. Are you sure it is save for the clearance between the piston and valves?
Nanoss22Thread starterPuerto rico · Jul 25, 2012#11
1 week and no problems it feel great i am jus giving some miles for the breaking they fit perfectly...
BEEFnorth carolina · Jul 25, 2012#12
so you were getting 111hp before the pistons? that is awesome. I would love to see what just the pistons did. I understand that dyno runs cost so most of the time it isn't cost effective to do multiple dyno runs inbetween mods.

I can't wait to see what you get out of this thing.
fast2882Indonesia · Jul 26, 2012#13
so, really don't have any problem with the clearance between valve and pistons? wow.... do you know what your car compression ratio ? 13:1?
fast2882Indonesia · Jul 26, 2012#14
Here in Indonesia, tuner have tested on Yaris that the head can be milled for maximum 1mm and the compression ratio become around 11.5:1. If this piston swap is successful, than this can become the highest compression ratio for 1nz-fe gasoline engine. Please dyno run to see the gain?
Nanoss22Thread starterPuerto rico · Jul 26, 2012#15
In puerto rico i have some friends with yaris hb with the prius pistons swap i am waiting for them forthe dynoo numbers.. They have other mods that i would like to do if i see the gains with those mods.. the max hp that i got with mi car was 114 with the apex tuneup the last time the heat in the dyno afected the numbers 108 in that run my old apex vafc at 5000rpm it wasnt setting up and the airfuel ratio was going down to 12 very rich at fuel now with the apex safc i am expecting new numbers and no problem with the airfuelratio... Btw in this mods the head canot be touch so the valve and piston clearence well you can see it in the pics
fast2882Indonesia · Jul 27, 2012#16
My Yaris head is still factory std, so i can do the piston swap too, but i'm still really curious for your compression ratio, is it really 13:1 and still don't have detonation problem using 91 pump gas?
fast2882Indonesia · Jul 27, 2012#17
Wow... 13:1 street 1Nz-Fe, cast piston, the compression ratio is similar to mazda sky active newest technology
Flipper_1938Kentucky · Jul 27, 2012#18
Originally Posted by fast2882 ↑
My Yaris head is still factory std, so i can do the piston swap too, but i'm still really curious for your compression ratio, is it really 13:1 and still don't have detonation problem using 91 pump gas?
Everything I have seen lists the 1NZ FXE engine at 13:1 compression ratio!
fase4Venezuela · Jul 28, 2012#19
I'm seeing those piston on that 1nz-fe and I'm drooling. I want to see a dyno sheet
Nanoss22Thread starterPuerto rico · Jul 29, 2012#20
Stock piston 195 to 205 compression prius 245 to 260 compress
Bluevitz-rsOshawa, Ontario, Canada · Jul 29, 2012#21
That's a huge jump
ViperoniBrampton, ON · Jul 29, 2012#22
That is pretty high too... pumped to see the dyno results!!
fast2882Indonesia · Jul 30, 2012#23
what is this mean?
fast2882Indonesia · Jul 30, 2012#24
Stock piston 195 to 205 compression prius 245 to 260 compress ?
ViperoniBrampton, ON · Jul 30, 2012#25
Originally Posted by fast2882 ↑
Stock piston 195 to 205 compression prius 245 to 260 compress ?
Stock engine compression (with 10.5:1 compression ratio) is apparently 195-205psi
With the 1NZ-FXE (with 13:1 compression ratio) engine compression is appanrelty 245-260psi
Nanoss22Thread starterPuerto rico · Aug 1, 2012#26
Did the compresion test 240 only one 238 nice numbers everithing running great...
fast2882Indonesia · Aug 1, 2012#27
prius engine compression 245-260Psi, Nanoss22 compression 240, so it means the compression ratio is about 12:1 to 12.5:1? wow, if the car use VP racing fuel, i think the power and torque gain will be great. Can't wait for the dyno result.....
BEEFnorth carolina · Aug 1, 2012#28
I wonder what kind of power just the pistons will make and then if you actually tuned for it (maybe with the aem fic).
fast2882Indonesia · Aug 2, 2012#29
if he use high octane number for fuel like VP racing, increasing the compression from 10.5 to 12, with proper tuning for the ecu, he should have about 10 to 15 extra HP on crank.
ljming99Singapore · Aug 2, 2012#30
Originally Posted by fast2882 ↑
if he use high octane number for fuel like VP racing, increasing the compression from 10.5 to 12, with proper tuning for the ecu, he should have about 10 to 15 extra HP on crank.
The rough baseline for compression is approx 5hp for every 0.5 increase, so from 10.5 to 12.

I would also give the same answer 10 ~ 15 hp as well =)
Autocross72Seattle · Aug 14, 2012#31
Any Dyno numbers yet?
Bluevitz-rsOshawa, Ontario, Canada · Aug 20, 2012#32
this thread was doing so well.... then splat
BEEFnorth carolina · Aug 20, 2012#33
I too was hoping for a big nasty dyno graph. something to coax me into doing something foolish with my money.
ilikericesavannah, ga · Aug 21, 2012#34
ehh.. its only been a couple weeks since his last post. Probably either blew his engine and embarassed to talk about it or just simply got busy with something else and doesn't wanna waste time with us =(

patience
1.5Tampa · Aug 21, 2012#35
Or enjoying all of that powaaaa lol ^
Nanoss22Thread starterPuerto rico · Aug 22, 2012#36
Sorry i was specting to have the numbers to and for the moment i dont have the time to go and do the dynopull the work family and the college got me crazy and yes the engine is running good no problems for the moment the car feel very diferent when i step on it so dont worry i will gave u the numbers and some videos of the dynopull... So be pacient
thebarberGrand Rapids, MI · Aug 22, 2012#37
Originally Posted by ilikerice ↑
ehh.. its only been a couple weeks since his last post. Probably either blew his engine and embarassed to talk about it or just simply got busy with something else and doesn't wanna waste time with us =(

patience
or he has a life outside of internet forums...
Bluevitz-rsOshawa, Ontario, Canada · Aug 22, 2012#38
Originally Posted by thebarber ↑
or he has a life outside of internet forums...
Psh, 😎
DeathBeardLos Angeles, CA · Aug 26, 2012#39
too bad you can't take full advantage of the compression with bigger cams
taman86United States · Sep 16, 2012#40
So any update to this? Still running? Dyno? Also I was wondering what engine managment you are using to run these. Stock, piggyback, or standalone? Where did you souce these from, new or another engine.
ilikericesavannah, ga · Sep 16, 2012#41
we are all still waiting for some kinda update on this one..
taman86United States · Sep 18, 2012#42
does anyone have this guys number and give him a call. I WANT UPDATES!!!
moh-6.304976,106.765952 · Sep 20, 2012#43
+1
Autocross72Seattle · Sep 29, 2012#44
I'm guessing he blew up the engine. That is way too much compression to be running on pump gas and cast pistons. To run as much compression as he had you would need forged pistons and run race gas. Mother wise you would not be able to control detonation. Of course, he could prove me wrong by posting an up date, but physics predicts that he won't be doing that.
jetblastNor Cal · Nov 2, 2012#45
Don't forget the toothpick con rods.
ViperoniBrampton, ON · Nov 5, 2012#46
Originally Posted by Autocross72 ↑
I'm guessing he blew up the engine. That is way too much compression to be running on pump gas and cast pistons. To run as much compression as he had you would need forged pistons and run race gas. Mother wise you would not be able to control detonation. Of course, he could prove me wrong by posting an up date, but physics predicts that he won't be doing that.
You sure that the motor would gain that much power from a 1.5 point compression ratio bump that the cast pistons and stock rods would crack and pop?

Worst case you need 94 octane.
ilikericesavannah, ga · Nov 6, 2012#47
@Viperoni
I dont think its the "power" that he is referring to that will blow up the motor, but the compression itself and not using correct precautions. We will never know because OP hasnt updated
fast2882Indonesia · Apr 6, 2013#48
Hello there, any update ? dyno result maybe?
GolddeenohColumbia, SC · Apr 6, 2013#49
what would go first the cylinder walls or the connecting rods?
fast2882Indonesia · Apr 6, 2013#50
maybe piston hit the valve