Yarisworld Archive

prius piston swap

100 posts · 60,760 views · page 2 of 2

Replies continued

GolddeenohColumbia, SC · Apr 6, 2013#51
i was referring to should it function what would stress out first. valve clearance would be the first issue maybe a shim gasket to gain clearance and lower compression ratio while also adding block guards might work great.
fast2882Indonesia · Apr 7, 2013#52
too bad the project isn't work, i still really curious about the result if someone can swap this piston and have about 12:1 compression ratio in 1nz-fe engine. toyota 1NR-fe engine series have 11.5:1 compression ratio, so i think actually it is possible to have 12:1 too.
BEEFnorth carolina · Apr 7, 2013#53
I think 12:1 is possible and even 12.5:1 with premium gas. the prius pistons are 13:1 so it is pushing it.

MicroImage has higher compression pistons for sale but i don't know of anyone that has done it. his 9:1 pistons are very popular in the boosted community.
jetblastNor Cal · Apr 7, 2013#54
With that we'd be hangin' out in the FRS compression ratio arena.
ViperoniBrampton, ON · Apr 7, 2013#55
Originally Posted by jetblast ↑
With that we'd be hangin' out in the FRS compression ratio arena.
Or pretty much any other direct injection gas motors...
13:1 is nothing unusual if you have cams though.
JustDidItUnited States · Apr 8, 2013#56
Originally Posted by Golddeenoh ↑
what would go first the cylinder walls or the connecting rods?
Originally Posted by fast2882 ↑
maybe piston hit the valve
Doubt either...

Originally Posted by fast2882 ↑
maybe piston hit the valve
Possible.. Would def want to clay before starting the car.

A lot of this is repeat from other threads..but seems very feasible:

Originally Posted by Viperoni
The (static) CR would be 13:1 if you use Prius (FXE) pistons.
The dynamic CR is apparently 11:1 if you use FXE pistons
The most I may need to change when running 11:1 compression is 91 instead of 87 pump gas, besides some EM. But even then....I run on 87 now...at the supposed static CR of 13:1 or dynamic 11:1.

List of Different Parts:
Crankshaft:
1NZ-FE: 13401-21020
1NZ-FXE: 13401-21040

Cam 1:
1NZ-FE:13502-21031
1NZ-FXE: 13502-21021

Cam 2:
1NZ-FE:13501-21030
1NZ-FXE: 13501-21060

Cam Gear:
1NZ-FE: 13050-21041
1NZ-FXE: 13050-21051)

Rings:
1NZ-FE: 13011-21041
1NZ-FXE: 13011-21100

Pistons:
1NZ-FE: 13101-21070
1NZ-FXE: 13101-21110

Valve Springs:
1NZ-FE: 90905-01049
1NZ-FXE: 90501-23135

List of parts that ARE the same...
Sprocket:
1NZ-FE: 13050-21041
1NZ-FXE: 13050-21041

Timing Chain:
1NZ-FE: 13506-21050
1NZ-FXE: 13506-21050

Rods:
1NZ-FE: 13201-29735
1NZ-FXE: 13201-29735

Bearings: all three SAME
13041-21022-01
13041-21022-02
13041-21022-03

Cylinder Head:
1NZ-FE: 11101-21062
1NZ-FXE: 11101-21062

Engine Block:
1NZ-FE: 11401-29856
1NZ-FXE: 11401-29856

Valves Seals:
1NZ-FE: 90913-02092
1NZ-FXE: 90913-02092

Intake Valves:
1NZ-FE: 13711-21010
1NZ-FXE: 13711-21010

Exhaust Valves:
1NZ-FE: 13715-21010
1NZ-FXE: 13715-21010
Bluevitz-rsOshawa, Ontario, Canada · Apr 8, 2013#57
I can only assume the differences in the crankshaft are due to the differences in the weight of the pistons and the operating speed of the 1NZ-FXE vs. the 1NZ-FE. But all the other differences make sense.
Flipper_1938Kentucky · Apr 8, 2013#58
Originally Posted by Bluevitz-rs ↑
I can only assume the differences in the crankshaft are due to the differences in the weight of the pistons and the operating speed of the 1NZ-FXE vs. the 1NZ-FE. But all the other differences make sense.
I bet it has to do with how the generator attaches to the crank (where the flywheel would normally sit).
Picture not included in this copy
Bluevitz-rsOshawa, Ontario, Canada · Apr 8, 2013#59
Yeah, that makes more sense.
JustDidItUnited States · Apr 9, 2013#60
Originally Posted by Flipper_1938 ↑
I bet it has to do with how the generator attaches to the crank (where the flywheel would normally sit).
Good point...
cali yarisCanoga Park, CA · Apr 9, 2013#61
I wonder how much a crankshaft would cost so I could compare them. I have a 1NZ-FE one sitting here.
fast2882Indonesia · Apr 9, 2013#62
so, what should i do then in order to swap the 1nz-fxe piston into my 1nz-fe?
fast2882Indonesia · Apr 9, 2013#63
what i know is : 1nz-fxe has a greater effective expansion than compression—making it simulated Atkinson cycle, rather than the conventional Otto cycle. That difference makes the cam timing and lift different ( i think ). So, if we use 1nz-fe cam, which mean the ignition timing is more advance than the 1nz-fxe cam, do they still have a clearance between top of the piston and the valve?
JustDidItUnited States · Apr 9, 2013#64
Originally Posted by fast2882 ↑
what i know is : 1nz-fxe has a greater effective expansion than compression—making it simulated Atkinson cycle, rather than the conventional Otto cycle. That difference makes the cam timing and lift different ( i think ). So, if we use 1nz-fe cam, which mean the ignition timing is more advance than the 1nz-fxe cam, do they still have a clearance between top of the piston and the valve?
THAT is still one of the bigger questions... prob best to clay the piston and find out b4 firing it up. Try it at your own risk...

....but I'm sure it would be fine....
nanossPuerto Rico · Apr 10, 2013#65
For those who think that i blewup the engine guess what it running good no problem just got the valve stems replaced to stop oil consume.... since august the engine has run like oem no problems like i said there no modification needed only swap your pistons for the prius one and u are set... i dont have the time to go to the dyno yet but i think the gains are 8whp only the piston the compression is 253 253 260 250 u are thinking that mod for only 8whp well i am trying to find better camshaft with more valve opening duration in order to gain the max hp with the compression.... some people said. To me that the scion xb exhaust cams haver more duration than all the 1nz fe engines
nanossPuerto Rico · Apr 10, 2013#66
The moods in my car are thes 2 1/4 magnaflow freflow 2" catless exhaust pipe thinking of making 2 1/4 downpipe.... echo semi header, ebay cai, 3" velocity apex neo afc and prius pistons....
thebarberGrand Rapids, MI · Apr 10, 2013#67
8whp not too bad considering its just a compression bump. That IS about 8% gain (though I do realize you're guessing)
JustDidItUnited States · Apr 10, 2013#68
Originally Posted by nanoss ↑
For those who think that i blewup the engine guess what it running good no problem just got the valve stems replaced to stop oil consume.... since august the engine has run like oem no problems like i said there no modification needed only swap your pistons for the prius one and u are set... i dont have the time to go to the dyno yet but i think the gains are 8whp only the piston the compression is 253 253 260 250 u are thinking that mod for only 8whp well i am trying to find better camshaft with more valve opening duration in order to gain the max hp with the compression.... some people said. To me that the scion xb exhaust cams haver more duration than all the 1nz fe engines. The moods in my car are thes 2 1/4 magnaflow freflow 2" catless exhaust pipe thinking of making 2 1/4 downpipe.... echo semi header, ebay cai, 3" velocity apex neo afc and prius pistons....
Good to hear back from you! Thanks for the follow up.
Flipper_1938Kentucky · Apr 10, 2013#69
Originally Posted by nanoss ↑
For those who think that i blewup the engine guess what it running good no problem just got the valve stems replaced to stop oil consume.... since august the engine has run like oem no problems like i said there no modification needed only swap your pistons for the prius one and u are set... i dont have the time to go to the dyno yet but i think the gains are 8whp only the piston the compression is 253 253 260 250 u are thinking that mod for only 8whp well i am trying to find better camshaft with more valve opening duration in order to gain the max hp with the compression.... some people said. To me that the scion xb exhaust cams haver more duration than all the 1nz fe engines
When VVT kicks in, what does it actually change? Does it do anything for lift or duration? or does it just advance/retard the camshafts?

Would causing the solenoid to fire sooner make the motor think it had more cam?
JustDidItUnited States · Apr 10, 2013#70
Originally Posted by nanoss ↑
i am trying to find better camshaft with more valve opening duration in order to gain the max hp with the compression.... some people said. To me that the scion xb exhaust cams haver more duration than all the 1nz fe engines
Yes, if you don't mind, tell us more about this idea.
fast2882Indonesia · Apr 10, 2013#71
why don't you try to use higher octane or racing fuel like VP racing, and have your ignition timing and Air fuel ratio retune by piggyback ECU first? i think with this two modification, you'll gain some additional HP and torque
fast2882Indonesia · Apr 10, 2013#72
for racing camshaft, Jun auto already release a higher lift and timing camshaft, in indonesia, we use these cam when we race.
cali yarisCanoga Park, CA · Apr 10, 2013#73
^ At $800 each (x2 !), they are pricey. Easier and cheaper to regrind camshafts here. We're doing a set for a customer now.
JustDidItUnited States · Apr 10, 2013#74
Originally Posted by cali yaris ↑
^ At $800 each (x2 !), they are pricey. Easier and cheaper to regrind camshafts here. We're doing a set for a customer now.
REALLY? You guys do regrinds? Didn't see that service available online. If we were looking at the JUN cam profile, Duration (mm): 66 (264) Lift (mm): 9.5 (race profile) OR Duration (mm): 63 (252) Lift (mm): 9.0 (street profile), what could something like this run? Rough estimate?

Originally Posted by fast2882 ↑
for racing camshaft, Jun auto already release a higher lift and timing camshaft, in indonesia, we use these cam when we race.
+$1000 for cams seems REALLYdiculous for our lil 1.5...
Jason@SportsCarDebary, FL · Apr 10, 2013#75
Originally Posted by cali yaris ↑
^ At $800 each (x2 !), they are pricey. Easier and cheaper to regrind camshafts here. We're doing a set for a customer now.
$800 x 2? I paid 84,200 Yen for the 9.5 cam set and 14,000 Yen for air shipping, at that time the total was $1077.23 to my door. With the current exchange rate (assuming the price is still the same) $984.95.

Now the hidden cost is that you may need to relieve the head to fit the 9.5mm cams, the taller lobes can hit the head casting. 😉

We have used a regrind before, works fine, and other than shimming the lifters you don't need to touch the head. 👍
cali yarisCanoga Park, CA · Apr 10, 2013#76
^ That's right the price did come down. I still say it's pricey compared to sending off a couple of cores for grinding, especially if the head doesn't need corresponding work.
GolddeenohColumbia, SC · Apr 10, 2013#77
What about just getting MI to make a Head with +1 mm valves, a set of custom ground cams, and a port and polish? then it should be as simple as making sure the cams are clocked right, the head is torqued down to spec and the timing marks line up, then go go go.

^ just saying, if we ask enough they eventually will have to supply to the demand.
JustDidItUnited States · Apr 10, 2013#78
Originally Posted by Golddeenoh ↑
What about just getting MI to make a Head with +1 mm valves, a set of custom ground cams, and a port and polish? then it should be as simple as making sure the cams are clocked right, the head is torqued down to spec and the timing marks line up, then go go go.

^ just saying, if we ask enough they eventually will have to supply to the demand.
^ That!!
nanossPuerto Rico · Apr 10, 2013#79
Ok a friend was telling me that the scion xb 1st gen the exhaust camshaft have more duration the same valve lift but longer the time to close the valve. I am interested in jun cams but the thing that is keep me worried is the lift since the piston are a lill bit higher the valve could hit the pistons...
ViperoniBrampton, ON · Apr 11, 2013#80
Thanks for posting again Nanoss!

Does anyone have specs on the cams?
I did a quick search and couldn't find a FSM.
nanossPuerto Rico · Apr 11, 2013#81
Yeah that will be usefull to know...
salmanghiyasPakistan · Nov 4, 2014#82
Originally Posted by nanoss ↑
Yeah that will be usefull to know...
Thread dead ?
japleKuala Lumpur, Malaysia · Nov 6, 2014#83
any updates?
JimKellyfanthe good Carolina · Nov 22, 2014#84
Lotta work for very little HP. Me, I am shootin fer handling first, then play with braking. But, even the Blitz sounds better, and that too is a lotta dough for a little go
YarisPRMayaWest, Puerto Rico · Dec 31, 2014#85
I've been running the Prius pistons for a while now, cero problems ��
Next step is getting a emanage and tune it with something other than 93 octane for Track Days only ��
Flipper_1938Kentucky · Jan 11, 2015#86
Originally Posted by YarisPR ↑
I've been running the Prius pistons for a while now, cero problems ��
Next step is getting a emanage and tune it with something other than 93 octane for Track Days only ��
In your opinion, how much hp did you gain with the piston swap?
YarisPRMayaWest, Puerto Rico · Jan 11, 2015#87
Originally Posted by Flipper_1938 ↑
In your opinion, how much hp did you gain with the piston swap?
Prius Pistons + port & polish head where 18whp, and its a fact not an opinion cause the car was dynoed before an after (Y)
RagnaCaTVillalba, Puerto Rico · Jan 22, 2015#88
YarisPR who did your port and polish?
monchito18Puerto Rico, Isabela · Jan 24, 2015#89
Angelo still lives lol
RagnaCaTVillalba, Puerto Rico · Jan 28, 2015#90
Lets meet up in Puerto Rico... lets do that soon...
tankm249Gurabo, PR · Dec 26, 2015#91
I know the post is old but I would like to know the prius piston part number. Some stupid online sellers think the 1nzfe pistons and 1nzfxe pistons are the same. There are a lot of racers doing this mod in PR. But I wanna make sure I purchase the right piston. I don't wanna end up with the same piston I have. Please help.
RigaudRigaud, Quebec, Can. · Dec 26, 2015#92
Originally Posted by tankm249 ↑
I know the post is old but I would like to know the prius piston part number. Some stupid online sellers think the 1nzfe pistons and 1nzfxe pistons are the same. There are a lot of racers doing this mod in PR. But I wanna make sure I purchase the right piston. I don't wanna end up with the same piston I have. Please help.
Go on RockAsuto, you'll find the right part. \Their usually around $65 USD each.Also, might not be in stock at Rock Auto. Maybe some else here will suggest another place that has them stock

Go back a few pages and read..........part numbers are posted.
tankm249Gurabo, PR · Jan 31, 2016#93
Thanks
👍
tmontagueCaledonia Ont. · Jan 31, 2016#94
Can these pistons be run safely without an engine management on 94octane gas?

Obviously you wouldn't maximize the potential unless you had at least a piggyback ecu but i'm curious if the stock ecu can handle the increased compression if you run the appropriate octane gas?
xnamerxxso cal · Jan 31, 2016#95
Don't waste your time if you're running stock cams, the static compression ratio is so high that you'll be fighting detonation at low rpms. For these cams to really work you'll need some pretty aggressive cams.
thebarberGrand Rapids, MI · Apr 5, 2017#96
hmmm
YarisPRMayaWest, Puerto Rico · Apr 5, 2017#97
I'am rnning the prius pistons, with 93oct and greddy emanage ultimate
JustDidItUnited States · Apr 6, 2017#98
I'm already running 1NZFXE pistons on 93oct ... Picture not included in this copy but haven't updated my cams to 1NZFE yet. Picture not included in this copy
RigaudRigaud, Quebec, Can. · Apr 6, 2017#99
Originally Posted by xnamerxx ↑
Don't waste your time if you're running stock cams, the static compression ratio is so high that you'll be fighting detonation at low rpms. For these cams to really work you'll need some pretty aggressive cams.
😆
YarisbluVenezuela · May 23, 2017#100
Do you know if those pistons would work on a 2nz-fe?

Thankss