Why machined? Seems like a simple part. I guess putting the threads in it could be considered machining.
DIY INTAKE
233 posts · 91,701 views · page 2 of 5
Replies continued
That seem's backwards to me. I'm quite certain that if you increase airflow you must also increase fuel to keep your air/fuel ratio optimal. This is why more fuel is required with forced induction; because all a turbo or supercharger is really doing is forcing more air into the engine and the more air/fuel, the bigger the combustion. I think the main reason you see gains with a highflow intake is because it decreases resistance on the engine. Analogous to a lightened pully, less resistence leads to less power being saped away. So, the easier air can get into and out of the engine (highflow intake and exhaust), the less drag you have on the engine. I don't really know, however, this is just how I always thought it worked.🙂Originally Posted by ChinoCharles ↑I crunched the numbers on my trip out to Toledo today.
First of all, my average speed was 80. I touched 115 once, other than that I kept between 80 and 85, but to be fair we'll call it 80. I drove 269 miles including a couple of short city trips afterwards that amounted to about 5 miles. I filled up before I left because I was curious to see if the intake had any effect on gas mileage. I get back and go to the station and fill up again. From what I have read around the forums, I should be looking at around 30 MPG. I fill up at 8.1 gallons.
33.2 MPG.
Now, confirm or deny my thinking on this. I haven't run this by anyone yet.
I don't know if this engine is necessarily getting colder air as the intake is placed in the engine bay, but I can say that it is getting more air. You can hear it. The MAF sensor measures this increased flow and outputs this information in the form of a high-frequency signal. The ECU reads this signal and adjusts the air/fuel ratio accordingly... it will either run rich or lean depending on what the throttle body is demanding. Cars generally fluctuate between rich and lean constantly, a fact that you will become accustomed to if you ever get an AFR gauge. Anyway, since the engine is getting more air it needs less fuel to start a combustion reaction. This is the basis of an engine... oxygen catalyzes the reaction that occurs when a spark is added to fuel. More oxygen means the car will know it needs less fuel to get going, and in this way an intake can affect gas mileage.
Also, by this logic then an intake by itself on a car is NOT a speed mod. It is an economy mod, unless you have the supporting mods to get MORE fuel into the cylinder DESPITE what the MAF is telling the ECU. This is why an adjustable fuel pump and some type of tuning software is necessary to make a true performance-oriented 1NZ, no matter how you're getting oxygen into the cylinder. (NOS)
Am I right on this?
well if you are going to make it out of steel or aluminum..... you will have you machine it, be kinda hard to make it out of hand tools. Well if you were going to make it out of wood, then all you would need is some wood screws a drill and a saw :)Originally Posted by jdubau55 ↑Why machined? Seems like a simple part. I guess putting the threads in it could be considered machining.
I was saying make a CAD 3D model of it. Then send the CAD file to various vendors to see the cost of production. You could make it one continuous piece then. Heck no I would make a hand shaped model of it silly 🙄

👏
I'm going to be spending a lot of time on rollers if this car is going to have any kind of performance. Frequent trips to the dyno can be expensive, unless of course you sell your windshield as real estate. I'll never pay full price again, but I will put 20,000 miles on a year with that sticker on my window. Fair trade... TI can do some other stuff too, some of which I may look into soon.
She was so fast we had to strap her down!

... 🙄 😆 I'm going to spend a few days stewing on the results. For you experts, here is one to tinker with in the meantime.
My car has an intake, header, and pulley and it is running rich. You guys all said it would run lean. What does this mean?
sticker looks good, you little dyno wh0re 😁, I thought you were gonna put it at the back?
I was going to put it in the back, but it fit so nicely in my window stripe that I figured I'd put it on the front instead. The back is already so clean, why ruin it? That would be as dumb as having a rear wiper on a Yaris.
OH BURN! 😆
Anyone want to take a crack at these results? The car is running super rich now... I'm talking in the low 11's at WOT. WHAT DOES THAT MEAN?
OH BURN! 😆
Anyone want to take a crack at these results? The car is running super rich now... I'm talking in the low 11's at WOT. WHAT DOES THAT MEAN?
My .02's worth: You've increased the amount of incoming air. In order for your cars computer to overcome this lean condition, it starts taking more fuel. In other words, a lean condition creates a rich command in the computer, and vice versa. I've never heard of just an intake swap doing this. When you mention low 11's, I'm assuming your talking air to fuel ratio, correct? Are your plugs starting to foul out, what do they look like?
Don't want to hijack your thread, but I'm currently getting 35 mpg daily doing 75 on the highway and short city trips in my sedan. Gotta love this car.
Yes, we were running a low 11 AFR at WOT... and we have never heard of an intake doing that either.
That gives this intake some pronounced advantages and some pronounced disadvantages. One thing is for sure... I am going to see a rather substantial increase in gas mileage and power very soon.
Haven't looked at the plugs yet, but she is still running fine. I'll have to pull them out and take a looksie. They need to go soon anyway... time for some real spark.
Ashley, say something. 😆
That gives this intake some pronounced advantages and some pronounced disadvantages. One thing is for sure... I am going to see a rather substantial increase in gas mileage and power very soon.
Haven't looked at the plugs yet, but she is still running fine. I'll have to pull them out and take a looksie. They need to go soon anyway... time for some real spark.
Ashley, say something. 😆

She sound much throatier now... thinking about putting a breather on the crankcase orface tube and plug the hole in the CAI so she breath fresh air
😳
may i ask what you didOriginally Posted by Black Yaris ↑She sound much throatier now... thinking about putting a breather on the crankcase orface tube and plug the hole in the CAI so she breath fresh air
Here you put it on the dyno then "stew" on the results. Bastard.....
here is the b4 pic... the filter sat just under the headlight
Picture lost · i78.photobucket.com
Picture lost · i78.photobucket.com
🙇 👏 🤘 🍻
I promise you you're the only one in the country with the betTRD.
I promise you you're the only one in the country with the betTRD.
BET?Originally Posted by ChinoCharles ↑🙇 👏 🤘 🍻
I promise you you're the only one in the country with the betTRD.
BETTY-RD
Gotcha..... I just call it a TuRD
wussup chino, low 11's huh? thats pretty cool man, dont know how you did it but you did. your on to something man, i just cant wait till you start producing it, cuz im definitely getting one. and the engine sound pretty damn beastly btw your bringin a whole new light to the 1NZ's.👏 👍 🙌
Low 11's when it comes to your air-fuel ratio, not quarter mile times if that is what you thought I meant.
My car is definitely faster with this intake. The graphs prove that much. Peak HP increased a bit and torque stayed pretty much the same, but the difference is in how soon I am getting power and how late I am losing it. By about 3000 RPM I am within 3 ft/lbs of peak torque, and that doesn't change until about 5200 RPM. That makes me extremely happy.
The kicker is the AFR readings with the new parts... still not sure what to make of it. We will see what it is with the exhaust on.
My car is definitely faster with this intake. The graphs prove that much. Peak HP increased a bit and torque stayed pretty much the same, but the difference is in how soon I am getting power and how late I am losing it. By about 3000 RPM I am within 3 ft/lbs of peak torque, and that doesn't change until about 5200 RPM. That makes me extremely happy.
The kicker is the AFR readings with the new parts... still not sure what to make of it. We will see what it is with the exhaust on.
AFR numbers look pretty much on par with what I am seeing.
I'd be curious to put my stock air box back on and see if there's a difference...
I'd be curious to put my stock air box back on and see if there's a difference...
Yeah, but your intake is weird. Are you running a wideband? You should throw the stockie on and see what happens... takes 10 minutes. 😁 Pwetty pweeze?
I may help throw Joe's car on the dyno this weekend. If that TRD intake runs rich, watch out... I am going to explode.
I may help throw Joe's car on the dyno this weekend. If that TRD intake runs rich, watch out... I am going to explode.
Yes... you have your ugly Betty, I have my TwistyTake... 😁
I'm pretty sure my sensor is not wideband, might look into upgrading in the future. How are you getting your readings? At the dyno place, or do you have a new sensor we do not know about?
Gonna be a busy week here, so it sounds like it'll be a weekend project 🙂
I'm pretty sure my sensor is not wideband, might look into upgrading in the future. How are you getting your readings? At the dyno place, or do you have a new sensor we do not know about?
Gonna be a busy week here, so it sounds like it'll be a weekend project 🙂
Dyno gives AFR, as well as 4089374872 other readings. Pretty cool shit. I wish I magically had a wideband and AFR gauge... thats about one grand down the road though.
Thomas, don't worry about it... well, don't do it for me. If you're curious yourself, swap them, but I'll find what I'm looking for one way or another.
Tomorrow is supposed to be just uber nice weather here, so I am going to do some fun stuff to the ride. Painted rear badge, a more involved light tinting and a finished power window kit. I'm just excited to get outside.
Thomas, don't worry about it... well, don't do it for me. If you're curious yourself, swap them, but I'll find what I'm looking for one way or another.
Tomorrow is supposed to be just uber nice weather here, so I am going to do some fun stuff to the ride. Painted rear badge, a more involved light tinting and a finished power window kit. I'm just excited to get outside.
Don't worry darling, I would do anything for you 😳Originally Posted by ChinoCharles ↑Thomas, don't worry about it... well, don't do it for me. If you're curious yourself, swap them, but I'll find what I'm looking for one way or another.
Ah nothing like a sunny modding day... Have fun!
you relize that is someones phone # in San Jose CA?Originally Posted by ChinoCharles ↑Dyno gives AFR, as well as 4089374872 other readings.
who's gonna dare to prank call..
"You just won a Toyota Yaris courtesy of yarisworld dot com! Just send us $15,000 to ship it over to you!"
"You just won a Toyota Yaris courtesy of yarisworld dot com! Just send us $15,000 to ship it over to you!"
yea i know AFR low 11's thats still pretty danm good, and and increase in HP early in the rpms up to the late 5200's not bad either, with an exaust you should deffinitly see a greater increase in the performance of this intake. all that air needs help getting outta the engine and thats what the exaust does.Originally Posted by ChinoCharles ↑Low 11's when it comes to your air-fuel ratio, not quarter mile times if that is what you thought I meant.
My car is definitely faster with this intake. The graphs prove that much. Peak HP increased a bit and torque stayed pretty much the same, but the difference is in how soon I am getting power and how late I am losing it. By about 3000 RPM I am within 3 ft/lbs of peak torque, and that doesn't change until about 5200 RPM. That makes me extremely happy.
The kicker is the AFR readings with the new parts... still not sure what to make of it. We will see what it is with the exhaust on.
it should help.
WTF.... I jump in my car first thing in the morn, and my car threw a check engine light... WTF???? I double checked all connections, everything a-ok... WTF... why does my car not like the modded TRD intake... it is 95% like Chino's.... I am going to swap back to the stock box for shits and giggles to make the light go away then work from that... more updates later
BTW... It is FUCKIN BEAUTIFUL outside in Ohio today... think they said 70... my ass is out side all day, I only came in to make this post, and to check my email
BTW... It is FUCKIN BEAUTIFUL outside in Ohio today... think they said 70... my ass is out side all day, I only came in to make this post, and to check my email
Aw, sorry to hear that Joe! BOOOO if you need it cleared we've got the hardware.
And yes, its fucking crazy outside. I just found the problem with my window kit so that is almost finished now, I'm zip tying and putting panels back on as we speak. Headlights are coming off too... if I can figure out how. 😆
And yes, its fucking crazy outside. I just found the problem with my window kit so that is almost finished now, I'm zip tying and putting panels back on as we speak. Headlights are coming off too... if I can figure out how. 😆
are you painting your healights tonight aswell? I figured while I had my bumper pulled down to reinstall the FULL TuRD intake I will just bake my lights and paint them, go down to the AZ and get the LED's to replace those ugly orange stocks... Today would have been a good day to road trip out that way... but I am doing too much shit around the house and to my car :)Originally Posted by ChinoCharles ↑Aw, sorry to hear that Joe! BOOOO if you need it cleared we've got the hardware.
And yes, its fucking crazy outside. I just found the problem with my window kit so that is almost finished now, I'm zip tying and putting panels back on as we speak. Headlights are coming off too... if I can figure out how. 😆
The headlights are already out. I'm masking them now... and my power windows work again.
damn you chino... you are already ahead of me... I have to wait till the wife goes to work so she don't bitch.... you baking them? or they just pulling apart in the warm temp we are having today?Originally Posted by ChinoCharles ↑The headlights are already out. I'm masking them now... and my power windows work again.
Damn this is a far cry from DIY intake
Its all good. Its my thread. -Cartman voice- I do what I want! 😉
Not baking them or pulling them apart. I'm selling out... I bought a can of night shades. I'm redoing the tail lights and side markers to look the same as they did with the vinyl but a tad darker. The headlights are getting eyebrows. No more orange reflector.
Not baking them or pulling them apart. I'm selling out... I bought a can of night shades. I'm redoing the tail lights and side markers to look the same as they did with the vinyl but a tad darker. The headlights are getting eyebrows. No more orange reflector.
where ya get the night shades? and how much?
Summit racing, cheap as hell. I think it was 6 bucks a can or something. Honestly, I have been a lifelong hater of tint-in-a-can, but so many owners here have had luck with it that I figure what the hell... worse comes to worse I'll strip it off.
wish I would have known you can get it there... I would have had you pick a can up b4 you came here... I have been wanting to redo my taillights... my I been lookin at those pix with our cars next to each other and your dark tails make my car look bad...everything else on my car is black... but the tails :(
Makes it look so fresh and so clean clean clean...
On a brighter, more on-topic note, Betty goes to the shop today. By next week you may see an intake and exhaust for sale... for a combined price that will make you giggle.
On a brighter, more on-topic note, Betty goes to the shop today. By next week you may see an intake and exhaust for sale... for a combined price that will make you giggle.
Chino with no ride :(
Just for a day. 😁




she looks so sad :(
OMG her face broken and eyes ripped out... Yaris snuff pics!
wft? 🤷
did you use the stock screws on maf
No.Originally Posted by KSIbucky ↑did you use the stock screws on maf
Yaris has been violated lol, but next week huh didnt expect it to launch so soon, cant wait for it dude ive been waitin this whole thread for it, pricing pricing why will it make us giggle. im curious now to know how much it is😳Originally Posted by ChinoCharles ↑Makes it look so fresh and so clean clean clean...
On a brighter, more on-topic note, Betty goes to the shop today. By next week you may see an intake and exhaust for sale... for a combined price that will make you giggle.
Might have to jump in on this. 😉
I just got an e-mail from the dyno... they must have ZPI-titis. Their welder will be gone this weekend, so that means no test pipe for me. I wish I was dead. Guess it'll have to wait till next weekend.
In the meantime, I'm FINALLY driving the prototype up there tomorrow. I know I said I was going to ship it overnight, but the investment I've made in this project is already getting crazy. I'm going to have right around $1000 of my own money sunk into this by the time we start finishing them... kinda crazy.
Then we sit here and wait for MAF plates. I got to see an adapter they did for a custom Mustang CAI and I have to say it was pretty sweet. Whereas the hacked-up xA intake was a plate sunk into the piping, these adapters are concave so they fit to the contour of the pipe you're using. You literally cut a hole, slap it on and get to welding. Should make life very easy for us, but most importantly it makes the piece look very clean and professional.
Also, we finally sourced all the couplers we would need. We are using Turbonetics silicon tubing couplers. They're a little more expensive, but again, it makes the piece look cleaner, and it doesn't change the pricing goal that much.
Bippity boppity boo motherfuckers. I'm hoping for the group buy next weekend, but don't hold your breath. As I am finding out quickly in this mess, anything can happen. The more realistic, less optimistic guess is that you guys will see the first final product the weekend of the 31st. Then she goes out for some "independent testing" with the group buy nipping at the heels.
In the meantime, I'm FINALLY driving the prototype up there tomorrow. I know I said I was going to ship it overnight, but the investment I've made in this project is already getting crazy. I'm going to have right around $1000 of my own money sunk into this by the time we start finishing them... kinda crazy.
Then we sit here and wait for MAF plates. I got to see an adapter they did for a custom Mustang CAI and I have to say it was pretty sweet. Whereas the hacked-up xA intake was a plate sunk into the piping, these adapters are concave so they fit to the contour of the pipe you're using. You literally cut a hole, slap it on and get to welding. Should make life very easy for us, but most importantly it makes the piece look very clean and professional.
Also, we finally sourced all the couplers we would need. We are using Turbonetics silicon tubing couplers. They're a little more expensive, but again, it makes the piece look cleaner, and it doesn't change the pricing goal that much.
Bippity boppity boo motherfuckers. I'm hoping for the group buy next weekend, but don't hold your breath. As I am finding out quickly in this mess, anything can happen. The more realistic, less optimistic guess is that you guys will see the first final product the weekend of the 31st. Then she goes out for some "independent testing" with the group buy nipping at the heels.
where's the evil grin smiley when you need it....
😈