Yarisworld Archive

Boost Gets U Laid eh? Count me In

129 posts · 54,717 views · page 1 of 3

yaris2010RSOriginal postAngus, Ontario · Feb 5, 2012#1
***MOD'S IF THE TITLE IS A ISSUE LET ME KNOW, ILL CHANGE IT PLEASE DONT DELETE***

So ive finally got just about all my turbo together and set up, just waiting for a install date (by the looks of it install date will be the week of the Feb 20th)

so far my kit consists of:

GT2052 turbo
1zz fuel injectors
AEM FIC
PnP Boomslang harness
2.5" exhaust with HighFlow Cat
Front Mount I/C
AEM wide band o2 gauge
Autometer boost gauge
HKS Bov SSQV

*looking for oil pressure gauge
*plan this week to go out and get some new spark plugs (either 6 or 7 heat rating)
*plan for new clutch within a year

watch for FS threads with no longer needed yaris parts
*Weapon R Dragon Intake

my plan is to keep it around 4-6PSI, i plan to keep all internals stock, stock fuel pump, i do plan to hook up the water line to the turbo also

i am very worried about this install for a few reasons, first it is my DD so i simply cannot afford to be Stuck. this is y i have planned for the install to take place durring the week of the 20th, i have the week off both school and work.

i have read so much and hopefully learned something along the way but i still have a few pre install questions.

since this car wil be my DD i need to do a slow install, so i need to know what i can drive with on my car without killing something. my plan was to install the fuel injectors and spark plugs the weekend before, can the 1znfe engine using the stock ecu drive with the 1zz injectors? also i plan to gap my spark plugs at .032 im assuming this will not be a problem to have.

another issue im not sure about is the oil lines. YES i know i need to tap the block for oil return line, but what about the oil feed line? i havent seen many threads with this discussed. i have recently seen a few people with the sandwich adapter, is this the only way or can i get feed from anywhere?

the vacuum line for the BOV, where does it go?

FITTINGS, is there a special grade of fittings i need to shop for? i dont like shopping for these things online, id like to find them locally, anyone know of some stores to start at for looking for fittings?

something else that has lapsed my mind till now, what is the purpose to wrap the turbo? is this important or not? what is the reason

Replies 128

Pur_BluEast Bay, Castro Valley · Feb 5, 2012#2
good luck on the install seems u got the right parts for a safe install of course tuning once installed is a must for any turbo. Any pics of the parts. Im sure we've all seem it a thousands times but for me it never gets old.
xixarchangelxixOakville, Ontario · Feb 6, 2012#3
Hit me up if you need any help
cali yarisCanoga Park, CA · Feb 6, 2012#4
You only have two weeks to source the rest of the parts? Hmmm...

1. What psi is the spring in the turbo, assuming you have an internal wastegate?
2. What reasoning led you to that spark plug gap?
3. I don't see manifold, downpipe, or any piping on your list. What's up with that?

You can grab an oil line from the oil pressure sensor exit.

since this car wil be my DD i need to do a slow install, so i need to know what i can drive with on my car without killing something. my plan was to install the fuel injectors and spark plugs the weekend before
This is worrisome. You WILL have some downtime turbo-ing a Toyota Yaris at some point. Period. Further, injectors and plugs save maybe 20-30 minutes on your install Doing that as a separate mod beforehand is not helpful.

Got more questions?
yaris2010RSThread starterAngus, Ontario · Feb 6, 2012#5
Thanks Garm,

i got a custom maifold made at a friends shop (his dad shop rebuilds classic cars) and i also got the downpipe and full exhaust with high flow cat partly fabricated 2.5"mandrel bent (enough for me to put it all on my car and then take it there later for "adjustments")

lol, i got the gap size from the other threads ive read, turbo members complained with the bigger gap they were missing.

for the the I/C piping, i have a shit-ton of aluminum pipe 2.25", some straight, some 90's and even more black silicone fittings with crome clamps.
ilikericesavannah, ga · Feb 6, 2012#6
I highly do not recommend doing this project without another form of transportation. Speaking from experience, even having a shop doing the work, may take longer than just 2 weeks. I say this because they will not be working on your car "alone". They will have other cars that are quick and easy money compared to a modified yaris which will give them headaches if this is thier first turbo yaris.

You need to have alot of time, patience and mechanically inclined to really take on this yourself in 2 weeks also. Even if archangel is going to be there step by step.

I am just saying the chances of this going smooth and simple are slim. You may be one of the rare exceptions though. By all means, I dont know your personal situation, but if this is your DD and you plan on doing this in 2 weeks, expect some road blocks. Keep in mind you will probably have to run to the part store a few hundred times for misc. items.

you will have to learn AN and NPT fittings, which is which.

People use heat wrap on thier turbo and piping to reduce engine bay temps. being that the ECU is bolted to the fire wall next to the exhaust could potentially do some damage. turbo's build up ALOT of heat.
yaris2010RSThread starterAngus, Ontario · Feb 6, 2012#7
thanks, ilkierice (lol finally understood your mane when i was writing it)

ive assisted with turbo installs before but that was just as a helping hand. also dont get me wrong ive been getting ready for this for about a year now, also have had the turbo sitting in my basement for about a year and is basically all built and mocked up. i realize i will have mistakes and i will need to run out to the store many many times.

when i say this is my DD and only car it is, but i live with my mom and step dad, ill have access to another car if needed for a quick run to the store, i can also work out carpooling if needed to get to work or school. its just something i dont want to do but i have planned for it. also if need be and its not snowing or raining or stupid cold i could run over to the parts store on my bike.

i will have to find some heat wrap soon too, thanks

only reason this didnt get installed sooner was cuz we sold our house and we were renting for a while till our new house was built, we moved in Jan 20th and ive been like a fat kid wanting chocolate for this

i want this, i want this bad, almost like i need it
Focus_Sh1ftNew Jersey · Feb 6, 2012#8
Without even reading this thread: yes.

Now onto business.
my plan is to keep it around 4-6PSI, i plan to keep all internals stock, stock fuel pump, i do plan to hook up the water line to the turbo also
Ok.

i am very worried about this install for a few reasons, first it is my DD so i simply cannot afford to be Stuck. this is y i have planned for the install to take place durring the week of the 20th, i have the week off both school and work.
Not Ok. Be prepared to use alternate transportation. I hate to say it but things will go wrong. You can read all you like, but unforeseeable things will happen.

my plan was to install the fuel injectors and spark plugs the weekend before, can the 1znfe engine using the stock ecu drive with the 1zz injectors? also i plan to gap my spark plugs at .032 im assuming this will not be a problem to have.
Sure can. The ECU will adjust fuel trims to account for a smaller gap and larger injectors.

another issue im not sure about is the oil lines. YES i know i need to tap the block for oil return line, but what about the oil feed line? i havent seen many threads with this discussed. i have recently seen a few people with the sandwich adapter, is this the only way or can i get feed from anywhere?
Just use the sandwich adapter. It's by far the most simple solution. Plus you can put senders for gauges there also.

the vacuum line for the BOV, where does it go?
Anywhere that receives manifold pressure. Tap it right into the vacuum line that stems off the manifold.

FITTINGS, is there a special grade of fittings i need to shop for? i dont like shopping for these things online, id like to find them locally, anyone know of some stores to start at for looking for fittings?
Home Depot, Lowes, Sears hardware, etc. I agree buying fittings online is difficult, and I haven't had any problem with any of my fittings.

something else that has lapsed my mind till now, what is the purpose to wrap the turbo? is this important or not? what is the reason
I think this was already answered. I wouldn't worry about it too much tbh. Yes the turbo increases engine bay temps but it's really no cause for concern.

One last thing:
i want this, i want this bad, almost like i need it
Good attitude but not quite. You don't want this. You NEED this.

Good luck.
YodaFL · Feb 6, 2012#9
Just got the cliff notes. Here is my input.
Proper planning and it can be installed in a day. Thats how long it took me but I planned and mapped out evey step for a week. I did this on my DD and could only be out of work for 3 days. Things will go wrong yes, but having a proper detailed plan in place helps out alot. When i mean detailed I am talking about having it down to how many and what type of bolts go where, washers, gaskets, piping route, ect.
As far as something going wrong down the line, yes count on that and it can not be avoided.
ilikericesavannah, ga · Feb 6, 2012#10
sounds like you are ready. I wish you the best of luck.. I am jealous just the fact that you have all your stuff sitting at your feet.
cali yarisCanoga Park, CA · Feb 6, 2012#11
1. What psi is the spring in the turbo, assuming you have an internal wastegate?
Didn't answer this, and I'd like to see the manifold, please. 🙂
yaris2010RSThread starterAngus, Ontario · Feb 6, 2012#12
i was told the spring was set to ~7psi but unless i can verify this im not really gonna trust it. once its on im hoping to play with the wastegate preload till i can verify it will remain in the rage of 4-6
TURBO YARISUSA · Feb 6, 2012#13
You cannot run less boost than what the waste gate spring is unless you modify the waste gate hole to be larger. So if the waste gate is 7 psi that is the least amount of boost you can run.
YodaFL · Feb 6, 2012#14
Originally Posted by TURBO YARIS ↑
You cannot run less boost than what the waste gate spring is unless you modify the waste gate hole to be larger. So if the waste gate is 7 psi that is the least amount of boost you can run.
^^^ This. Its also very easy to port the hole larger.
cali yarisCanoga Park, CA · Feb 6, 2012#15
That's what I was headed for. Good help around here. 🙂
yaris2010RSThread starterAngus, Ontario · Feb 7, 2012#16
like i said its believed to be "set" to ~7, not sure what the base spring rate is
yaris2010RSThread starterAngus, Ontario · Feb 12, 2012#17
update:

so far I/C and piping has gone into the car and im running my intake through the I/C and it appears my car has more balls and my fuel efficency has gone up quite a bit (appears to be an 11% imporvement, proven on 2 tanks, mix of city, hwy and country driving)

gauges are also mounted (except water temp and oil pressure which im still trying to source) i decided to mount them a slightly different way then usual (pics will be posted once weather gets nicer) and therefore ill shortly have my gauge pod for sale

Question:

to run water temp, do i run this off water into the turbo or water out of the turbo? i am assuming if i go before the turbo ill get rad water temp but if i run after the turbo ill get turbo water temp. what is best? how big ofr a difference between the 2 readings should there be?
yaris2010RSThread starterAngus, Ontario · Feb 22, 2012#18
UPDATE:
turbo is installed and runs like a champ. working on a tune currently. so far everything went to plan and only issue i had was i refused to remove the A/C lines to install so i had to "build" my turbo while it was behind the block. (very annoying step to have one guy hold it from under the car and one guy hold it from above)

the turbo was pushing 6psi to start so i played with the waste gate thingy and preloaded it more so currently im pushing 9psi and all is well. im probably gonna lower the boost a bit, think 9psi might be a bit high for a DD

after i got it running and somewhat tuned the only code i got was a P0101 for the Mass or Volume Air Circuit Range, i am assuming this is due to too much air flowing thru the maf? the conflicting information of this is in the freeze frame data, the code was thrown while engine load was only 85%, rpm was 2171 and the maf (g/s) was 22.92. im wondering if this is a sign my bov isnt functioning correctly or i dont have the maf clamp working properly

tuning im looking greatly at the afr, i wanna make sure my engine is safe (again as it is my DD) and its jumping around alot, at a safe limit when i punch it (afr gauge says 10.0) and when im accelerating normally its around 11.6-12.5 and when im cruzing (with cruze control on) it jumps up to 13.6-15.0, this seems off to me. do these numbers sound right? or atleast safe?
cali yarisCanoga Park, CA · Feb 22, 2012#19
average of 14 for idle and cruising, 12's for regular acceleration, 11.5-12 for WOT.

Sounds like you are a too rich if you're hitting 10's.

to run water temp, do i run this off water into the turbo or water out of the turbo?
neither. You want block water temp.
yaris2010RSThread starterAngus, Ontario · Feb 22, 2012#20
so far changed my mind about water temp (having a hell of a time getting a water line to the turbo so no point imo) and i didnt end up running a oil gauge (there is no way im running a live oil line into my car and not enough room at the stock oil sensor to put the electric one), currently running with only boost gauge and afr gauge.

yeah i was thinking 10 was WAY too rich, ill try with a more refind tune, thanks for the numbers garm.

any idea about the P0101?
fnkngrvIn The Hotbox · Feb 22, 2012#21
Originally Posted by yaris2010RS ↑
after i got it running and somewhat tuned the only code i got was a P0101 for the Mass or Volume Air Circuit Range, i am assuming this is due to too much air flowing thru the maf? the conflicting information of this is in the freeze frame data, the code was thrown while engine load was only 85%, rpm was 2171 and the maf (g/s) was 22.92. im wondering if this is a sign my bov isnt functioning correctly or i dont have the maf clamp working properly
MAF clamping needs to be set because of what you have already stated...too much air flowing passed the sensor causing it to trip out. Since you are using the F/IC perhaps I can see about sending you my MAF map with the understanding that you are in a different climate/altitude, etc from be (Maine) and that anything you do with it is at your own risk. I am just getting tuned this week myself finally. Been running off the stock ECU only for 14k miles/8 months.

As for boost, I would start with 6/7 and verify whether or not you are going lean at the top of your curve. I am seeing that and therefore will be installing an aftermarket fuel pump most likely with a modified fuel rail and return in the next couple months.
Blown_xaVirginia · Feb 22, 2012#22
Originally Posted by yaris2010RS ↑
UPDATE:
turbo is installed and runs like a champ. working on a tune currently. so far everything went to plan and only issue i had was i refused to remove the A/C lines to install so i had to "build" my turbo while it was behind the block. (very annoying step to have one guy hold it from under the car and one guy hold it from above)

the turbo was pushing 6psi to start so i played with the waste gate thingy and preloaded it more so currently im pushing 9psi and all is well. im probably gonna lower the boost a bit, think 9psi might be a bit high for a DD

after i got it running and somewhat tuned the only code i got was a P0101 for the Mass or Volume Air Circuit Range, i am assuming this is due to too much air flowing thru the maf? the conflicting information of this is in the freeze frame data, the code was thrown while engine load was only 85%, rpm was
2171 and the maf (g/s) was 22.92. im wondering if this is a sign my bov isnt functioning correctly or i dont have the maf clamp working properly

tuning im looking greatly at the afr, i wanna make sure my engine is safe (again as it is my DD) and its jumping around alot, at a safe limit when i punch it (afr gauge says 10.0) and when im accelerating normally its around 11.6-12.5 and when im cruzing (with cruze control on) it jumps up to 13.6-
15.0, this seems off to me. do these numbers sound right? or atleast safe?
I'm not a tuner, but I can tell you the mass air flow volume code is most likely because the MAF voltage is being maxed out. It needs to be clamped in the tune. Roughly 5~7psi maxes it out.
BrianRiverside, CA · Feb 22, 2012#23
I would run an oil pressure gauge if I was you. It saved me when I had an oil pressure problem. There's more than enough room it the stock location to put a sensor in, I did.
cali yarisCanoga Park, CA · Feb 22, 2012#24
(there is no way im running a live oil line into my car and not enough room at the stock oil sensor to put the electric one),
Yeah, this just isn't true, it's where mine is installed. You know you replace the stock one with the one for the gauge, right? You don't use two sensors, in other words.
yaris2010RSThread starterAngus, Ontario · Feb 23, 2012#25
the shop i went to had a massive electric sender unit, also the adapter i have for my oil feed line (the split from the stock senser unit) uses metric thread on the end (where the stock sensor needs to go back) and imperial thread on the sides. i was told that shop and most shops in the area can only get imperial thread, not the metric ones.

a new code i seem to be getting (after i stalled) was P0335 CrankShaft Position Sensor A circuit. was this just caused from the engine stalling or could be sign of a serious issue? i didnt write down the freeze frame data on this code but i remember the TPS to be at 0% and engine rpm at 1160.
cali yarisCanoga Park, CA · Feb 23, 2012#26
I don't get why you still need the stock oil pressure sensor. Just replace it.
yaris2010RSThread starterAngus, Ontario · Feb 23, 2012#27
dont get me wrong i completely agree with you, and if i could find one with the same threads as the stock one i would.
fnkngrvIn The Hotbox · Feb 23, 2012#28
Originally Posted by yaris2010RS ↑
dont get me wrong i completely agree with you, and if i could find one with the same threads as the stock one i would.

Any reason why you can't swap out for an NPT fitting?
fnkngrvIn The Hotbox · Feb 23, 2012#29
Originally Posted by yaris2010RS ↑
a new code i seem to be getting (after i stalled) was P0335 CrankShaft Position Sensor A circuit. was this just caused from the engine stalling or could be sign of a serious issue? i didnt write down the freeze frame data on this code but i remember the TPS to be at 0% and engine rpm at 1160.
This could be a sign that your Boomslang is suffering from the same incorrect wiring that mine and a few others had. I can't recall as I am going on 2 hrs sleep in over 48 hrs right now, but it is either set to tap or intercept currently (possibly) and it should be tap I believe otherwise you will have issues. CTScott would be a great resource to PM to talk to about it. He went through my entire Bslang wire by wire to test/confirm proper termination and soldering, etc. He found several bad points and fixed them for me. He is an electrical genius if you haven't already been made aware of it and a great contributor to the community. Always willing to help.

Not saying that this is your issue for sure, but it a path to investigate. 🎉
yaris2010RSThread starterAngus, Ontario · Feb 23, 2012#30
i suppose i could, would just be a matter of finding one
yaris2010RSThread starterAngus, Ontario · Feb 23, 2012#31
Originally Posted by fnkngrv ↑
This could be a sign that your Boomslang is suffering from the same incorrect wiring that mine and a few others had. I can't recall as I am going on 2 hrs sleep in over 48 hrs right now, but it is either set to tap or intercept currently (possibly) and it should be tap I believe otherwise you will have issues. CTScott would be a great resource to PM to talk to about it. He went through my entire Bslang wire by wire to test/confirm proper termination and soldering, etc. He found several bad points and fixed them for me. He is an electrical genius if you haven't already been made aware of it and a great contributor to the community. Always willing to help.

Not saying that this is your issue for sure, but it a path to investigate. 🎉
ive read about this issue but i find it odd then that i've only gotten it twice, its not a common issue. only thing i can see possible is the connection in the harness is loose
yaris2010RSThread starterAngus, Ontario · Feb 23, 2012#32
Has anyone crashed their AEM FIC yet? lol, i ran into a very strange error when trying to connect my pc and it told me i had to reflash it....gay now i need to start all over again. tuning is such a PIA
BrianRiverside, CA · Feb 23, 2012#33
Originally Posted by yaris2010RS ↑
ive read about this issue but i find it odd then that i've only gotten it twice, its not a common issue. only thing i can see possible is the connection in the harness is loose
I had the same issue when I first installed the boomslang and FIC . The code appeared once and the never again until I sent my FIC back to AEM then the code came back once I reinstalled. I cleared it and havent seen it in 4 months.
cali yarisCanoga Park, CA · Feb 23, 2012#34
I think mainly the issue with the Boomslang is re-used stock pins coming out that had to be re-inserted, more that than actual incorrect wiring.
thebarberGrand Rapids, MI · Feb 23, 2012#35
boomslang harnesses are often crappily done...
yaris2010RSThread starterAngus, Ontario · Feb 23, 2012#36
^thats silly considering its a almost $500 harness......

but if it was a bad wiring job it would throw the P0335 code always, ive only gotten it twice. wondering if its a loose connection.....

would some di-electric grease on the connectors be a bad idea or a good preventitive measure?
yaris2010RSThread starterAngus, Ontario · Feb 23, 2012#37
okay so ive given up on trying to chase the p0335 code, it has yet to happen again so probably just a glitch.

now to tuning....... ugh, lol what a PIA this is. im not looking for max preformance, im looking for safe engine. currently i believe my issue starts with the injector change. i was under the impression 1zz injectors are 220cc and 1zn injectors are 190cc. are these numbers correct or are they throwing me off?
Blown_xaVirginia · Feb 23, 2012#38
Originally Posted by yaris2010RS ↑
okay so ive given up on trying to chase the p0335 code, it has yet to happen again so probably just a glitch.

now to tuning....... ugh, lol what a PIA this is. im not looking for max preformance, im looking for safe engine. currently i believe my issue starts with the injector change. i was under the impression 1zz injectors are 220cc and 1zn injectors are 190cc. are these numbers correct or are they throwing me off?
My advice to you, rescale injectors... And get it to the dyno for somebody to tune it. It is impossible to tune a car properly on the street. Just yesterday we got a 102whp gain over a street tune at the same boost ( just an example) on an evo.
yaris2010RSThread starterAngus, Ontario · Mar 25, 2012#39
UPDATE:

hey guys, sorry for the long wait since last update. boosted life is busy with all the laid im getting :D lol

for all those who said it cant be done, im street tuned with NO CEL code and Closed-Loop

so im still running with a street tune, planning to get properly tuned by mid summer as by then hopefully ill be done school and in a full time job. im not overly concerned with my tune, its getting great AFR's, slightly rich but id rather for a safe street tune. (~11.9WOT, 12.3-13.9 accel, 14.5-15.1 Cruze/idle)

currently my turbo is at 9psi and i dont plan on touching it, i havent had any issues thus far, but the new 2.5inch exhaust scrapes on everything! lol. i definatly feel a 300HP gain and im planning to get a turbo sticker so i should be well above the 350streetHP (on a serious note i feel a easy 50HP gain)

i get a bit of turbo flutter sometimes but not sure why..... any help? my system is BOV and MAF in stock location. i think it might be because i got sucked into a fake HKS SSQS valve, so im hopeing that could be it.

one thing that really worries me is my fuel efficiency (mpgs or L/100km).... its gone up.....alot......i mean my average l/100km is about 6.2l/100km, which is really good for my style of driving.


something else i have been pondering is how to know if i need to use 91 octane or if i can get away with using 89 or even 87 for everyday commuting? im afraid to get stuck with a tank of 89 and not being able to drive it. any ideas with this or even what i should listen for when testing it out would be great.
cali yarisCanoga Park, CA · Mar 25, 2012#40
congrats. A professional tune will clean up your map and might net you a little more power for the same boost.

I would only run 91 at 9psi on that motor. I suppose in a pinch you could try and keep it out of boost with 87 or 89, but I would do that sparingly. My .02
yaris2010RSThread starterAngus, Ontario · Mar 25, 2012#41
garm, thx for the $0.0196 (sorry for the exchange rate), that has been the general advice but no one can tell me exactly why that is.

i was speaking to a mechanic and he believed 89 or even 87 could be used with some retarding of the timing. he seems to believe since the car was designed to run on 87 and all the sensors are still being used (like i said above i was able to run in closed loop) the computer will adjust to use any type of fuel (87-96) u put in (and any ambient temp and PSIA). also with my tune i have not altered the MAF map, just clamped it a 4.5v, ive altered the ignition, fuel, and o2 only.

according to my buddy, if the computer see's something wrong, it will adjust for it and seeing as im not hiding boost from the computer it should adjust for it. now seeing as he works on chryslers and not toyota's and he doesnt deal with aftermarket installs im aware he doesnt know exactly whats going on but i do see his point of view.

is this plausable circumstance? or is it way out there? im hesitant to use 89 cuz i dont want to grenade my motor but at the same time lets try to save money where we can.
YodaFL · Mar 26, 2012#42
for peace of mind just use the premium fuel. This is just a cost of being turboed. BE safe than sorry its just a few cents more really. If u can afford to turbo you car you can afford premium fuel. 🙄
cali yarisCanoga Park, CA · Mar 26, 2012#43
that has been the general advice but no one can tell me exactly why that is.
That is because on a dyno there are controlled conditions under which the car can be tuned. Can't be said much clearer than that.

he seems to believe since the car was designed to run on 87 and all the sensors are still being used (like i said above i was able to run in closed loop) the computer will adjust to use any type of fuel (87-96) u put in
Ask him how he knows for sure that it will not start to detonate at 87. If it doesn't, great, you don't need 91. If it does, for long enough, you'll be buying a motor. Ask him if he'll cover that cost if he's wrong.
cali yarisCanoga Park, CA · Mar 26, 2012#44
p.s. LOL about about the exchange rate. 😆
yaris2010RSThread starterAngus, Ontario · Mar 26, 2012#45
Originally Posted by cali yaris ↑
That is because on a dyno there are controlled conditions under which the car can be tuned. Can't be said much clearer than that.
sorry garm, i missed this or how it solves the mystery of needed 91 octane on the street

Originally Posted by cali yaris ↑
Ask him how he knows for sure that it will not start to detonate at 87. If it doesn't, great, you don't need 91. If it does, for long enough, you'll be buying a motor. Ask him if he'll cover that cost if he's wrong.
i agree with this, if he could show me some type of equation that proves 87 would be fine then this would have been a discovery post vs a inquiry post. ive been looking into this a bit and found people delaying timing to fix issues when going from 93 octane to 89 octane.

what my friend was saying made sense to me, but i quite easy to convince.....good thing im not female....or too bad more females arnt like me..... back on topic, he basically was saying since im not hiding boost from my ecu, it will adjust for it, if it senses a knock it will adjust for it. i trust his opinion but really this fourm has the best of the best when it comes to specific questions like this.


Originally Posted by cali yaris ↑
p.s. LOL about about the exchange rate. 😆
lol, im glad u found it funny, i was worried it could be taken as a "snarky" comment, lol
YodaFL · Mar 26, 2012#46
If you really want to run 89 then get your engine tuned for it. Don't rely on the stock ecu to correct timing. The stock knock sensor is not all that good and not something I would trust when under any boost to control timing. Your talking about using a limited reactive system to correct timing with low octane gas while in boost. Bad idea. Too much timing retard can also be a bad thing for your motor and can lead to burnt valves. What ever fuel you want to use just be sure to get tuned for it. The Aem fic allows you to make two different maps.
You will have to turn down the boost to run low octane gas. Or just stay out of any high boost.
But really you need to be running premium. You never kno while driving on the road where you might need to suddenly accelerate to avoid a crash or something. That one time is all it takes for you to blow your motor. It can be done just not wise. If you love your car give it the best you can and premium fuel is not too much to ask. Good luck M8.

--Sent from IPhone
cali yarisCanoga Park, CA · Mar 26, 2012#47
^ Best answer.


Originally Posted by cali yaris
That is because on a dyno there are controlled conditions under which the car can be tuned. Can't be said much clearer than that.
sorry garm, i missed this or how it solves the mystery of needed 91 octane on the street
This had nothing to do with that. You said you didn't understand why dyno tuning was needed vs. street tuning.

if he could show me some type of equation that proves 87 would be fine
That's impossible. It detonates when it detonates. You are talking about a dynamic, complex system, that you have modified beyond its designed intent. This is why tuning is an art, using technoology, and experience, and ears and eyes. It's also a further explanation of why it's best to tune on the dyno.
yaris2010RSThread starterAngus, Ontario · Mar 26, 2012#48
Originally Posted by Yoda ↑
If you really want to run 89 then get your engine tuned for it. Don't rely on the stock ecu to correct timing. The stock knock sensor is not all that good and not something I would trust when under any boost to control timing. Your talking about using a limited reactive system to correct timing with low octane gas while in boost. Bad idea. Too much timing retard can also be a bad thing for your motor and can lead to burnt valves. What ever fuel you want to use just be sure to get tuned for it. The Aem fic allows you to make two different maps.
You will have to turn down the boost to run low octane gas. Or just stay out of any high boost.
But really you need to be running premium. You never kno while driving on the road where you might need to suddenly accelerate to avoid a crash or something. That one time is all it takes for you to blow your motor. It can be done just not wise. If you love your car give it the best you can and premium fuel is not too much to ask. Good luck M8.

--Sent from IPhone
^this is a very good answer

Originally Posted by cali yaris ↑
^ Best answer.






This had nothing to do with that. You said you didn't understand why dyno tuning was needed vs. street tuning.



That's impossible. It detonates when it detonates. You are talking about a dynamic, complex system, that you have modified beyond its designed intent. This is why tuning is an art, using technoology, and experience, and ears and eyes. It's also a further explanation of why it's best to tune on the dyno.
oh, sorry i missunderstood the contex of it. i strongly believe everyone should be dyno tuned, its by far the best and complete way to tune. seeing all the maps involved and measurements and readings i completely agree that dyno is the way to go. once funds come in i will definatly be getting a professional tune.
cali yarisCanoga Park, CA · Mar 26, 2012#49
And just to be really clear, we street tuned my car as well before our dyno sessions. You can get pretty close with that method - especially with two people in the car!
yaris2010RSThread starterAngus, Ontario · Mar 31, 2012#50
New update:

Ran into another issue, it seemed to happen very randomly but I could smell raw fuel in the cabin, thought it may have been random sections of super rich tune. Today I checked injectors and they appeared to be leaking slightly around the top and bottom o-rings. And on 2 injectors the bottom o-rings appeared to look different the other 2.... 3 hours or work, about 5 liters of fuel all over my garage and driveway, removing the injectors about 5 times and a trip to local junk yard the bottom o-rings were replaced.

I recommend to anyone removing fuel rail, when u put it back on double check the bottom injector gasket is properly in place. My was sitting half in the hole and half ontop, which caused a leak and allowed the fuel injector to wiggle and oblong the gasket hole.

Only issues I had to direct me towards the injector issue was raw fuel smell and a second or 2 extra starting crank time which I just thought was because of the turbo. Fixing the injectors stopped the fuel smell but my tune is off again (I need to tweek the tune) and now my car takes forever to start! It made it worse, hopefully retuning will fix this. Ill update tomorrow if tuning did fix this.

Anyone have some loose change and experience on this issue?