Damn man the price of being boosted. GL
Boost Gets U Laid eh? Count me In
129 posts · 54,717 views · page 2 of 3
Replies continued
price of being boosted, being escorted off the highway cuz the car made a loud noise and gave up...... 9psi@140km/h passing in the left lane and she died
a shit ton of questions from a curious officer later and 6bucks worth of batteries for my flashlight and asking a truck driver to borrow a wrench i put the intake pipe back on the TB :D
next time i get a chance to sit with my car, remove bumper and make sure all the I/C piping clamps are very very tight :)
a shit ton of questions from a curious officer later and 6bucks worth of batteries for my flashlight and asking a truck driver to borrow a wrench i put the intake pipe back on the TB :D
next time i get a chance to sit with my car, remove bumper and make sure all the I/C piping clamps are very very tight :)
This has happened to me many a times lol. 😳Originally Posted by yaris2010RS ↑price of being boosted, being escorted off the highway cuz the car made a loud noise and gave up...... 9psi@140km/h passing in the left lane and she died
a shit ton of questions from a curious officer later and 6bucks worth of batteries for my flashlight and asking a truck driver to borrow a wrench i put the intake pipe back on the TB :D
next time i get a chance to sit with my car, remove bumper and make sure all the I/C piping clamps are very very tight :)
scared the PISS outta me, lol. to make it worse due to traffic reasons i was forced to bail out on the left shoulder. luckly there was a officer about 2 mins behind me, and he said if i could get it moving he would escort me off the road
If you had a girl in your car when that happened, I dont think you will get laid that night.. HAHA.. just kidding.. enjoy your adventures with turbo
Biggest turbo thread without pics of the install.
Come on Jeff. Let's see how pretty of a job you did.
Come on Jeff. Let's see how pretty of a job you did.
lol kk, ill see how many cell phone pics i can take today while putting my rims on. i only have 2 pics of the install already and they are both just test fitting the I/C
good to see ur turbo and tune is running smooth has that p0335 engine check light come back on? mine doesnt go away!
sorry been super busy with work and school finals. djgab, yeah my light went away. double check your wiring and connectors. my issue i found to be in the boomslang harness itself.
continunity is your friend.
currently i have no engine codes. if i do a long run (0-170km/h) WOT i get a system rich code but i think thats due to my street tune. im currenty looking for a local shop to tune my car
continunity is your friend.
currently i have no engine codes. if i do a long run (0-170km/h) WOT i get a system rich code but i think thats due to my street tune. im currenty looking for a local shop to tune my car
so when do we get to see some pics? or are they posted somewhere?
VERY SORRY GUYS, i was so busy the last few months of school and now a new job......anyways excuses are done, i have pics from today when i finally got my coolant line installed. so far i lvoe my turbo, no issues and im currently still looking for a good place to get a tune. anyone know of any tuning places in GTA?
Intercooler
Picture not included in this copy
HKS SSQ BOV
Picture not included in this copy
i recently noticed my IAT was kinda high so i lowered my front plate and noticed a difference in temp
Picture not included in this copy
Turbo from under the car view, Axel Shaft plate and heat wrap have been removed, the braided line you are seeing is the coolant return and the rubber is the oil return.
Picture not included in this copy
turbo view from above (windshield cowel removed and heat wrap) braided line on the the left(with pink ziptie) is the coolant feed, to the right is the coolant return
Picture not included in this copy
engine bay picture (windshield cowel and engine cover removed)
Picture not included in this copy
Picture not included in this copy
TB (the braided line is my turbo coolant line, coolant return line goes to where that hse use to go)
Picture not included in this copy
intake pipe, MAF and under the headlight you can see the BOV
Picture not included in this copy
custom 2.5" Exhaust + HighFlow Cat
Picture not included in this copy
Rear View, Sorry car is very dirty. NOTE I REBUILT MY CENTER EXHAUST TO ACCOMODATE A 2.5" INLET AND OUTLET. (for those of you folloing along, exhaust only has highflow cat and muffler)
Picture not included in this copy
Stickers
Picture not included in this copy
Intercooler
Picture not included in this copy
HKS SSQ BOV
Picture not included in this copy
i recently noticed my IAT was kinda high so i lowered my front plate and noticed a difference in temp
Picture not included in this copy
Turbo from under the car view, Axel Shaft plate and heat wrap have been removed, the braided line you are seeing is the coolant return and the rubber is the oil return.
Picture not included in this copy
turbo view from above (windshield cowel removed and heat wrap) braided line on the the left(with pink ziptie) is the coolant feed, to the right is the coolant return
Picture not included in this copy
engine bay picture (windshield cowel and engine cover removed)
Picture not included in this copy
Picture not included in this copy
TB (the braided line is my turbo coolant line, coolant return line goes to where that hse use to go)
Picture not included in this copy
intake pipe, MAF and under the headlight you can see the BOV
Picture not included in this copy
custom 2.5" Exhaust + HighFlow Cat
Picture not included in this copy
Rear View, Sorry car is very dirty. NOTE I REBUILT MY CENTER EXHAUST TO ACCOMODATE A 2.5" INLET AND OUTLET. (for those of you folloing along, exhaust only has highflow cat and muffler)
Picture not included in this copy
Stickers
Picture not included in this copy
You gonna finish this so you can get rolled up by my stock sedan 😁
finish it? its been my DD forever and have been driving boosted with no coolant lines since Feb.... only thing i really got left is a professional tune
Looking good.
Excellent. Sleeper!
This turbo kit you have installed on your car looks ALOT like my old kit. But I sold it to someone else in Canada. Did you buy it from someone?
(Correction it is my old kit, I thought you had a different user name)
Looks good : )
(Correction it is my old kit, I thought you had a different user name)
Looks good : )
This car is really a sleeper, good stuff! :)
got a proper dyno and tune yesterday, the tuner gave me two tunes, one for street and one for track
Street
9.5PSI boost with 155WHP @ 5500RPM (184HP @ crank)
Max Torque 160Ft-lbs @ 4000RPM
Track
9.5PSI with 162WHP @ 4300RPM (190HP @ Crank)
Max Torque 161Ft-lbs @ 4000rpm
He said my set up is restricted by the exhaust, he says there is alot of restriction in the system. im looking at getting an exhaust dump to fix this situation (electronic servo opens an exhaust dump before the restriction)
i have the print out of my Street tune VS the Professional tune. kinda disapointed that i only got my street tune vs professional, when i first saw it i thought it was professional street tune vs professional track tune. he said also there was alot of heat soak of the engine so on the street he said it felt more like 160hp but he is looking forward to seeing my car again with the exhaust dump.
another side note, with my street tune i was only loosing max 5hp, but the curves are way different.
Picture not included in this copy
Street
9.5PSI boost with 155WHP @ 5500RPM (184HP @ crank)
Max Torque 160Ft-lbs @ 4000RPM
Track
9.5PSI with 162WHP @ 4300RPM (190HP @ Crank)
Max Torque 161Ft-lbs @ 4000rpm
He said my set up is restricted by the exhaust, he says there is alot of restriction in the system. im looking at getting an exhaust dump to fix this situation (electronic servo opens an exhaust dump before the restriction)
i have the print out of my Street tune VS the Professional tune. kinda disapointed that i only got my street tune vs professional, when i first saw it i thought it was professional street tune vs professional track tune. he said also there was alot of heat soak of the engine so on the street he said it felt more like 160hp but he is looking forward to seeing my car again with the exhaust dump.
another side note, with my street tune i was only loosing max 5hp, but the curves are way different.
Picture not included in this copy
1 attachment not included in this copy
Awesome, tuning makes all the difference.
1. Both tunes at 9.5 psi?
2. What's different between the two maps, and where is the 162 whp chart?
1. Both tunes at 9.5 psi?
2. What's different between the two maps, and where is the 162 whp chart?
Personally I love the turbo set up that Carlos designed. It has worked great on my car and really have a couple qualms. One being the internal wastegate, but that has been corrected now on mine and would be a non issue IMO on a southern car. The second would be something that really is inherent to many cars with the IC piping over the top and that is ensuring the pipe riding up over the cam cover from the front needs to be installed with the correct depths in the rubber intersection otherwise you will either rub on the bottom of it on the cam cover or rub the top of it on the hood.
Great works :)
Great works :)
Nice power...
I didn't get the 162whp chart, when he printed this out for me I quickly glanced at it and thought it was the street vs track map, after I got home and really looked it over I saw that its my tune vs his which was kinda disapointing. He said the only difference between the tunes are the fuel trims and timing, the street tune is safe and the track tune is more on the edge (and throws a engine code of o2 sensor high) I tried both out and they felt more or less the same.
What's the issues with internal wastegate? Where else would the wastegate go? Lol
I'm so happy with my low end power gain especially and how smooth the car feels. I can't believe how much of a difference the tune made, it feels stock turbo now. And my AFR's are super stable.
What's the issues with internal wastegate? Where else would the wastegate go? Lol
I'm so happy with my low end power gain especially and how smooth the car feels. I can't believe how much of a difference the tune made, it feels stock turbo now. And my AFR's are super stable.
so your street tune and his street tune were at 9.5 psi? What boost was for the 162 whp tune?
Internal wastegate is when the wastegate is inside the turbo. External is when you mount a separate wastegate outside the turbo.
Internal wastegate is when the wastegate is inside the turbo. External is when you mount a separate wastegate outside the turbo.
PM sent.
Yes both tunes are at 9.5psi. Only differences between the whp apparently are the maps themselves. He did suggest that 9.5 is a bit high for a dd so when I do the exhaust modifications I will most likely lower it or put an electronic wastegate actuator.
And I'd just like to clarify about the tunes, I wrote it kinda messed up, he gave me 2 professional tunes, one for street and one for track. I also have My own personal street tune but I will never be using that again. Just incase there was some confusion between the dyno'd street tune and mmy street tune.
And I'd just like to clarify about the tunes, I wrote it kinda messed up, he gave me 2 professional tunes, one for street and one for track. I also have My own personal street tune but I will never be using that again. Just incase there was some confusion between the dyno'd street tune and mmy street tune.
Still confused about the "track" tune. What was different about it to gain the hp?
tuned for higher octane perhaps?
^ It didn't sound like they drained the tank and put in different gas for this tuning.
Naw was same fuel, same everything. Nothing was changed except within the tuning parameters.
Only thing I really know about it is its not recomended by the tuner to run on a daily basis and it throws a engine code and my afr's are mostly richer. I guess the same way he tweeked out the extra hp from my own tune; he tweeked out a few extra hp from his own tune but feels its not as safe as his previous tune.
Only thing I really know about it is its not recomended by the tuner to run on a daily basis and it throws a engine code and my afr's are mostly richer. I guess the same way he tweeked out the extra hp from my own tune; he tweeked out a few extra hp from his own tune but feels its not as safe as his previous tune.
What octane fuel are you using?
Richer would make less power, not more. 🤷
yea. I would think that he means on the edge of lean hints the expression, "leaner is meaner" going on the rich side would be safer.Originally Posted by cali yaris ↑Richer would make less power, not more. 🤷
something sounds off with how your tuner does business, no offense, but it makes no sense whatsoever to think that it is safe or that there are different curves for the same octane rating fuel....sounds a bit odd to me.
^man dont start putting that in my head..... Also I'm running 91 octane.
Sorry guys I don't have much info about the tuning difference. I also wouldn't recommend the tuner as my afr's still fluctuate quite a bit.
Like said before, only thing I know is if I run the track tune I get system rich (afrs at 13.5ish cruise and about 12.2-12.5 wot) street tune I'm running 14.2-14.7 cruise and 12.5-12.8 wot
I plan to get a new exhaust with less restriction and get a retune so will most likely be getting it done at a different shop
Sorry guys I don't have much info about the tuning difference. I also wouldn't recommend the tuner as my afr's still fluctuate quite a bit.
Like said before, only thing I know is if I run the track tune I get system rich (afrs at 13.5ish cruise and about 12.2-12.5 wot) street tune I'm running 14.2-14.7 cruise and 12.5-12.8 wot
I plan to get a new exhaust with less restriction and get a retune so will most likely be getting it done at a different shop
Don't expect solid AFR's when tuning with the FIC. The onboard map sensor has no buffering, so even though you may be 7psi at wot from 3000rpm till redline (example) ... the map sensor rarely traces that.
Also, don't hassle between 2 maps. It just makes things more complicated. I have one map, lower boost levels are safe to run without meth injection. If I set my boost controller for over 20psi, that part of the map is optimized for meth injection. Over 27psi, the map will be optimized for race gas (have not done so yet).
Also, don't hassle between 2 maps. It just makes things more complicated. I have one map, lower boost levels are safe to run without meth injection. If I set my boost controller for over 20psi, that part of the map is optimized for meth injection. Over 27psi, the map will be optimized for race gas (have not done so yet).
With water/meth and raised boost on stock engine,has anyone been able to find the max power that can be safely made?
Most boosted engines [1nz fe] are rated at 180bhp. So am i right in saying that no matter water/meth or boost raise then is 180bhp all we can extract from the stock 1nzfe?
Most boosted engines [1nz fe] are rated at 180bhp. So am i right in saying that no matter water/meth or boost raise then is 180bhp all we can extract from the stock 1nzfe?
I wouldn't take it past 180whp with stock rods and pistons. Mine bent a rod two days after dyno run when I put out 197whp. It was a cool day and the car was just ripping fast. I guess a little to much boost at 12psi. I am still surprised it handled so much for so long. I drove at 10psi for a year with no problems. I ran 11.5/1 afr at wide open.
I also ran 10 psi for a very long time before one of my injectors clogged up. Just my luck. Got me 203whp tho. Just make sure you are tuned really good.
Most boosted engines [1nz fe] are rated at 180bhp.Agreed with the last two posts, but where do these "ratings" come from?
damn i dont have money for this :( i would get the zage turbo kit in there :(
Well my bad,been reading here and there. And this 180bhp figure got stuck.
At 180whp,i think that would meet my goals as this is my daily drive.
I seriously doubt the TRD turbo [IHI made] will make that power,though.
Regarding the stock inlet manifold,any substitute to that? What inlet mani are you people using?
At 180whp,i think that would meet my goals as this is my daily drive.
I seriously doubt the TRD turbo [IHI made] will make that power,though.
Regarding the stock inlet manifold,any substitute to that? What inlet mani are you people using?
^ lots of discussion about the intake manifold. We have one in development, and you should look up "tooter" thread about the one he is playing with.
Update:
BOOST DOES NOT GET YOU LAID!
It keeps you up all night for 2 days while you replace the motor, lol
^as you can read from above and probably guess i needed to replace my motor..... lol
I DONT REGRET ANYTHING AND CANT WAIT TO BE BOOSTED AGAIN, STOCK YARII IS SOOOOOOOO F'IN SLOW! lol.....
More updates to come......
BOOST DOES NOT GET YOU LAID!
It keeps you up all night for 2 days while you replace the motor, lol
^as you can read from above and probably guess i needed to replace my motor..... lol
I DONT REGRET ANYTHING AND CANT WAIT TO BE BOOSTED AGAIN, STOCK YARII IS SOOOOOOOO F'IN SLOW! lol.....
More updates to come......
you know I'm subscribed!
You kids and your overly ambitious boosting 😉
Sorry to hear though. At least it sounds like you've already got it covered.
Sorry to hear though. At least it sounds like you've already got it covered.
I LOVE being called a kid 😛
^LMFAO, Garm.....random question......How old are you?
Short Story: Water got into my stock ECM and threw my AFR's way way off. Unfortunately as this is my daily driver i was forced to drive it while I was trying to trace back to the issue. And engine stopped working
Picture not included in this copy
Yes I Took my Cowl apart on the side of the road to get the car going again……
Long and Painful Story: The first real sign of an issue was after my car shut down in a carwash. It would crank over but wouldn’t catch. Finally I decided i had to bump it off the starter to get it out of the car wash out of the way from the other dirty car owners. I figured water had gotten into a connector and once it dried it would be fine so I walked across the street, had lunch and some beers and when I came back she struggled but it started. It ran great till I got to my next client and let the car sit in the parking lot. When I came back out again it struggled to start and once it did start I had my dash board dancing like a Christmas tree. (engine, trac, slip, abs, ebrake, airbag, oil and a few other lights I never saw before were flashing on and off)
I called it a day and Took it home and immediately started trying to find the problem. I found light corrosion on the boomslang harness pins and also light corrosion on the ECM pins. I cleaned the corrosion the best I could and I put enough dielectric grease to comfortably do a rectal examination on an elephant. Started the car and the car was running and idling very good, I felt comfortable I had solved the problem. I took it for a quick test drive around the block and found all AFRs were reasonable, slightly off but I gave it the benefit of the doubt and trusted it was due to the ECM relearning the stock fuel trims
At this point please keep in mind I didn’t say there was a lot of logic behind my method of thinking. If you really really think about it you can make anything sound plausible and that exactly what I did……
After about a week of driving I noticed My AFRs still wernt quite normal and seemed to be getting slightly worse, I believed it had something to do with a change or resistance on the pins so I would need to retune to correct the issue, I attempted to adjust my maps on the FIC and found the engine would not react as expected, I then went looking for more corrosion.
Remember at this point also my car has been driving for over a week with the AFRs all over the place without any engine light or CEL codes, using my OBD2 I did see that my ECM wasn’t even reading my O2 sensor 2 bank 1 voltage and my sensor 1 was fluctuating when the car was in the on position but not on. Also at this point I am beginning to smell unburnt fuel and exhaust emissions inside the cabin while I was driving, I believed this was a sign my car AFRs were rich and my AEM wideband was in fact reading incorrectly and what ever buggered up that sensor also buggered up my O2 sensor 1 (remember that thing I said about being able to give logic to anything……exhibit (A))
After a very late night of myself working on the car and keeping CTScott up past his bed time too( To whom I owe many thanks to), he convinced me that water may have gotten into the Toyota SEALED ECM and is causing the isuses, so I opened it up and found what would be the cause of the issue.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
And what was left after I cleaned corrosion, notice pins from the IC chip are in fact missing
Picture not included in this copy
Picture not included in this copy
First thing I did the next morning was drive over to Toyota and showed them the Pics and issues I was having, I spoke firmly and directly to the service manager. They agreed to cover the ECM under warranty and they ordered the part right away without even looking at my car. Only problem at this point was my ECM was going to take about a month as they were on back order and showed stock no where. Also apparently Toyota is no longer able to give out loner cars while your car is out for repair so I was left with the dealer (and the person I called at Toyota Canada) saying its my decision to find alternate means of transportation or drive the car.
After many heated conversations with the dealer and Toyota Canada they did rush the part in in about a week, but this was one more week of me driving my car with crazy AFRs. I did try to stay away from boost as much as possible but it was not uncommon to go up to 4PSI (wastegate was set to 9) While I was waiting for the new ECM I did disconnect my boomslang harness as with only the stock ECM is was more stable for everyday driving but still would get super rich and super lean at random intervals.
After I got my New ECM i left my boomslang harness unplugged to try and have the new ecm relearn the stock fuel trims correctly. First thing I noticed was the AFRs were more constant and much more stable then the old ECM, also it was now reading both my O2s in a stable way. Second thing I noticed was I still had the smell of fuel and exhaust in my cabin. I checked header and everything looked good, I couldn’t find an exhaust leak and even checked my injectors for leaks.
After a few days of driving like this the smell was getting worse, when the car was hot (after about 1.5 hours of driving) I popped the hood with the car still running and saw a thick stream of steam and exhaust and significant oil particles coming out of the breather tube……. I purchased a long tube and ran it under my car so I would survive the drive home. By the time I got home the car was backfiring, missing, and smoking like a MOFO out of the breather and exhaust.
I checked compression and it was as followed:
Test #1: Car sat aprox 40 mins before test
Cylinder 1 - - 155 – 158 PSI
Cylinder 2 - - 154 – 157 PSI
Cylinder 3 - - 155 – 159 PSI
Cylinder 4 - - 153 – 156 PSI
Test #2: Car run hard and compression checked within 10 mins
Cylinder 1 - - 160 – 165 PSI
Cylinder 2 - - 161 – 167 PSI
Cylinder 3 - - 159 – 164 PSI
Cylinder 4 - - 163 – 166 PSI
Also I did a leak down test and saw a very minimal drop
I left the car that night and came out in the morning to take it to the dealer to see what was up. They told me I needed a complete engine rebuild as I have significant blow by (NO F/CK/NG SHIT, I TOLD YOU THAT AS SOON AS I WALKED IN!!!!! GRRRRR) I told them the engine replacement was on them as it was their faulty computer that caused the engine to go. After lots and lots of yelling and swearing and phone calls with Toyota Canada (and I think they made a phone call to the cops too cuz they just happen to be driving around in the parking lot briefly) Toyota offered to cover about 50% of the cost but would not cover the entire engine replacement as “A Stock, unmodified Yaris would have been able to withstand the conditions the ECM was creating”
I told them they would never see the green of my money again. (or pink and blue and brown……yes we know our Canadian money is colourful) and left a one-wheel-peel out of their drive through bay (which also left some colourful smoke and toxic fumes)
All I knew at this point was I needed my Daily driver to get back to work. Luckily I remembered Barber (who I would also like to thank greatly) had a very mint, well taken care of Stock yaris engine from a 2010 with about 20,000km (12,427 Mi). I snagged that up and found where I had put all my Stock yaris parts and got to work, It took me 3 days (17 hours total) to do the swap. I am working on the Engine Swap DIY, as I found out there isn’t one…….
Picture not included in this copy
engine being brought back from The Barbers in the back of a borrowed oversized pickup for the job
Picture not included in this copy
Engine getting to my house and unloaded from Pickup (yes 2 guys can put it in but one guy cannot take it out)
Picture not included in this copy
Engine removal
Picture not included in this copy
Old Engine, New Engine, Tranny, Stock Clutch
Picture not included in this copy
Stock Clutch
Picture not included in this copy
Thickness of stock clutch (i should have taken a measurement but I didn’t…..)
Picture not included in this copy
New engine mated with stock tranny all polished and cleaned, ready to go in
I polished up the engine and tranny and Once the new engine was in, she started up great and is running like a champ. Threw in some sea foam to get rid of any deposits left inside and have had no mechanical issues thus far, only issue I had was about half way through my day the car died….. apparently those ground wires on the left side of the engine (drivers side) are very important……DO NOT ONLY HAND TIGHTEN THESE BOLTS! THEY WILL COME LOOSE, YOU CAR WILL SHUTDOWN! Lol…….
When I was all done, came inside and my GF had made me Cookies! YAY ME! Im gonna do engine swaps more often
Picture not included in this copy
Will Update with what Actually went wrong in the stock engine when i get a chance to get into it. Also will create the engine swap DIY and post once its ready with Pics. I do believe it was the Top end (valves/cam) that went wrong, i do not believe it was a gasket or pision rings...... Like i said i will keap you posted.
All in all i do not regret boosting and i cant wait to create a 300bhp motor to drop back in. I am very unsatisfied with Toyotas actions and the way they treat me dirrectly (i have never been treated this much as a kid in my life) I am not saying they should have replaced the motor no questions asked but they should not haven spoken to me the way they did. This experience will greatly influence my decision when i purchase my next Vehicle. I love toyota but they are falling through the holes and no longer treating customers as number one.
Short Story: Water got into my stock ECM and threw my AFR's way way off. Unfortunately as this is my daily driver i was forced to drive it while I was trying to trace back to the issue. And engine stopped working
Picture not included in this copy
Yes I Took my Cowl apart on the side of the road to get the car going again……
Long and Painful Story: The first real sign of an issue was after my car shut down in a carwash. It would crank over but wouldn’t catch. Finally I decided i had to bump it off the starter to get it out of the car wash out of the way from the other dirty car owners. I figured water had gotten into a connector and once it dried it would be fine so I walked across the street, had lunch and some beers and when I came back she struggled but it started. It ran great till I got to my next client and let the car sit in the parking lot. When I came back out again it struggled to start and once it did start I had my dash board dancing like a Christmas tree. (engine, trac, slip, abs, ebrake, airbag, oil and a few other lights I never saw before were flashing on and off)
I called it a day and Took it home and immediately started trying to find the problem. I found light corrosion on the boomslang harness pins and also light corrosion on the ECM pins. I cleaned the corrosion the best I could and I put enough dielectric grease to comfortably do a rectal examination on an elephant. Started the car and the car was running and idling very good, I felt comfortable I had solved the problem. I took it for a quick test drive around the block and found all AFRs were reasonable, slightly off but I gave it the benefit of the doubt and trusted it was due to the ECM relearning the stock fuel trims
At this point please keep in mind I didn’t say there was a lot of logic behind my method of thinking. If you really really think about it you can make anything sound plausible and that exactly what I did……
After about a week of driving I noticed My AFRs still wernt quite normal and seemed to be getting slightly worse, I believed it had something to do with a change or resistance on the pins so I would need to retune to correct the issue, I attempted to adjust my maps on the FIC and found the engine would not react as expected, I then went looking for more corrosion.
Remember at this point also my car has been driving for over a week with the AFRs all over the place without any engine light or CEL codes, using my OBD2 I did see that my ECM wasn’t even reading my O2 sensor 2 bank 1 voltage and my sensor 1 was fluctuating when the car was in the on position but not on. Also at this point I am beginning to smell unburnt fuel and exhaust emissions inside the cabin while I was driving, I believed this was a sign my car AFRs were rich and my AEM wideband was in fact reading incorrectly and what ever buggered up that sensor also buggered up my O2 sensor 1 (remember that thing I said about being able to give logic to anything……exhibit (A))
After a very late night of myself working on the car and keeping CTScott up past his bed time too( To whom I owe many thanks to), he convinced me that water may have gotten into the Toyota SEALED ECM and is causing the isuses, so I opened it up and found what would be the cause of the issue.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
And what was left after I cleaned corrosion, notice pins from the IC chip are in fact missing
Picture not included in this copy
Picture not included in this copy
First thing I did the next morning was drive over to Toyota and showed them the Pics and issues I was having, I spoke firmly and directly to the service manager. They agreed to cover the ECM under warranty and they ordered the part right away without even looking at my car. Only problem at this point was my ECM was going to take about a month as they were on back order and showed stock no where. Also apparently Toyota is no longer able to give out loner cars while your car is out for repair so I was left with the dealer (and the person I called at Toyota Canada) saying its my decision to find alternate means of transportation or drive the car.
After many heated conversations with the dealer and Toyota Canada they did rush the part in in about a week, but this was one more week of me driving my car with crazy AFRs. I did try to stay away from boost as much as possible but it was not uncommon to go up to 4PSI (wastegate was set to 9) While I was waiting for the new ECM I did disconnect my boomslang harness as with only the stock ECM is was more stable for everyday driving but still would get super rich and super lean at random intervals.
After I got my New ECM i left my boomslang harness unplugged to try and have the new ecm relearn the stock fuel trims correctly. First thing I noticed was the AFRs were more constant and much more stable then the old ECM, also it was now reading both my O2s in a stable way. Second thing I noticed was I still had the smell of fuel and exhaust in my cabin. I checked header and everything looked good, I couldn’t find an exhaust leak and even checked my injectors for leaks.
After a few days of driving like this the smell was getting worse, when the car was hot (after about 1.5 hours of driving) I popped the hood with the car still running and saw a thick stream of steam and exhaust and significant oil particles coming out of the breather tube……. I purchased a long tube and ran it under my car so I would survive the drive home. By the time I got home the car was backfiring, missing, and smoking like a MOFO out of the breather and exhaust.
I checked compression and it was as followed:
Test #1: Car sat aprox 40 mins before test
Cylinder 1 - - 155 – 158 PSI
Cylinder 2 - - 154 – 157 PSI
Cylinder 3 - - 155 – 159 PSI
Cylinder 4 - - 153 – 156 PSI
Test #2: Car run hard and compression checked within 10 mins
Cylinder 1 - - 160 – 165 PSI
Cylinder 2 - - 161 – 167 PSI
Cylinder 3 - - 159 – 164 PSI
Cylinder 4 - - 163 – 166 PSI
Also I did a leak down test and saw a very minimal drop
I left the car that night and came out in the morning to take it to the dealer to see what was up. They told me I needed a complete engine rebuild as I have significant blow by (NO F/CK/NG SHIT, I TOLD YOU THAT AS SOON AS I WALKED IN!!!!! GRRRRR) I told them the engine replacement was on them as it was their faulty computer that caused the engine to go. After lots and lots of yelling and swearing and phone calls with Toyota Canada (and I think they made a phone call to the cops too cuz they just happen to be driving around in the parking lot briefly) Toyota offered to cover about 50% of the cost but would not cover the entire engine replacement as “A Stock, unmodified Yaris would have been able to withstand the conditions the ECM was creating”
I told them they would never see the green of my money again. (or pink and blue and brown……yes we know our Canadian money is colourful) and left a one-wheel-peel out of their drive through bay (which also left some colourful smoke and toxic fumes)
All I knew at this point was I needed my Daily driver to get back to work. Luckily I remembered Barber (who I would also like to thank greatly) had a very mint, well taken care of Stock yaris engine from a 2010 with about 20,000km (12,427 Mi). I snagged that up and found where I had put all my Stock yaris parts and got to work, It took me 3 days (17 hours total) to do the swap. I am working on the Engine Swap DIY, as I found out there isn’t one…….
Picture not included in this copy
engine being brought back from The Barbers in the back of a borrowed oversized pickup for the job
Picture not included in this copy
Engine getting to my house and unloaded from Pickup (yes 2 guys can put it in but one guy cannot take it out)
Picture not included in this copy
Engine removal
Picture not included in this copy
Old Engine, New Engine, Tranny, Stock Clutch
Picture not included in this copy
Stock Clutch
Picture not included in this copy
Thickness of stock clutch (i should have taken a measurement but I didn’t…..)
Picture not included in this copy
New engine mated with stock tranny all polished and cleaned, ready to go in
I polished up the engine and tranny and Once the new engine was in, she started up great and is running like a champ. Threw in some sea foam to get rid of any deposits left inside and have had no mechanical issues thus far, only issue I had was about half way through my day the car died….. apparently those ground wires on the left side of the engine (drivers side) are very important……DO NOT ONLY HAND TIGHTEN THESE BOLTS! THEY WILL COME LOOSE, YOU CAR WILL SHUTDOWN! Lol…….
When I was all done, came inside and my GF had made me Cookies! YAY ME! Im gonna do engine swaps more often
Picture not included in this copy
Will Update with what Actually went wrong in the stock engine when i get a chance to get into it. Also will create the engine swap DIY and post once its ready with Pics. I do believe it was the Top end (valves/cam) that went wrong, i do not believe it was a gasket or pision rings...... Like i said i will keap you posted.
All in all i do not regret boosting and i cant wait to create a 300bhp motor to drop back in. I am very unsatisfied with Toyotas actions and the way they treat me dirrectly (i have never been treated this much as a kid in my life) I am not saying they should have replaced the motor no questions asked but they should not haven spoken to me the way they did. This experience will greatly influence my decision when i purchase my next Vehicle. I love toyota but they are falling through the holes and no longer treating customers as number one.
WOW. What a story lol.
I'm really surprised to see that water made its way into the ECU. I'm even more surprised that Toyota didn't completely blow you off for having such a heavily modified car. You must be pretty damn persuasive.
A DIY for engine removal would be really awesome. I figure at one point or another I'll be in that boat, and would love to have something to reference.
All in all, I'm glad to see you're not discouraged though. Things can and will go wrong when you modify an engine so much, but the outcome is always worth it.
Oh. And them cookies. 🤤
I'm really surprised to see that water made its way into the ECU. I'm even more surprised that Toyota didn't completely blow you off for having such a heavily modified car. You must be pretty damn persuasive.
A DIY for engine removal would be really awesome. I figure at one point or another I'll be in that boat, and would love to have something to reference.
All in all, I'm glad to see you're not discouraged though. Things can and will go wrong when you modify an engine so much, but the outcome is always worth it.
Oh. And them cookies. 🤤
Garm, you ARE a kid. At heart, at least. 😛Originally Posted by cali yaris ↑I LOVE being called a kid 😛
X2Originally Posted by Focus_Sh1ft ↑WOW. What a story lol.
Looks like you had an exhaust leak on no. 1 and 2 at the head/manifold.
the exhast leak was an on going issue with the turbo, since i never supported the bottom of the turbo i had to keep tightning the header bolts