Yarisworld Archive

Projector HID Retrofit:

86 posts · 20,786 views · page 1 of 2

SAV912Original postSavannah, GA · Jan 9, 2012#1
I am having such a difficult time with this!! Neither how-to by Brian or Peter seems to be getting me anywhere.

I have the headlights apart, and then realized that the kit doesn't have any silicone in it. I don't know if it just isn't included anymore, if Garm missed it, or if I was suppose to order it separately. I'll have to get with him about that.

The order of the locking rings on the back is all out of whack. And I have no idea where the large beige rubber piece goes. At this point, I'm really debating just going to Home Depot in the morning, getting some silicone and putting my lights back together and sending these back to Garm because this is not a 4-5 hour job like the how-to's said. I've been at this for 10 hours now and I have to get lights on the front of my car by Tuesday afternoon because I go back to work then.

Ugh! Yarisworld, please help!!

-C

Replies 85

SAV912Thread starterSavannah, GA · Jan 9, 2012#2
😠This is where I'm at right now.

Picture not included in this copy

The only way the projector seems to fit in there with any remoteness of security is without the thin washer and without that rubber grommet. Even then, it feels like it might come loose after driving a while and the projector bouncing around in my bowl is not what I spent $200 for.

Picture not included in this copy

This is the untouched second projector, as it was when I pulled it out of the box. I haven't touched the order of the grommet or any of the rings. The only thing I did was take out the bulb.

Picture not included in this copy

These two pieces don't seem to have a home, and unless I am blind, I'm not seeing where they get inserted in either how-to. And here I thought the hard part would be getting the headlights apart and getting all the wiring done. Getting them apart was a breeze. Haven't even started the wiring yet because I can't get these Goddamn things to work. Even if I do, I have no idea how I'm gonna seal my lights back up.
BrianRiverside, CA · Jan 9, 2012#3
If you're close to a Nissan dealer, go the the parts department and ask for this part #, B6553-89915. It's the headlight sealant. Can you post a pic of what you're having trouble with? It's been a while since I've used them.
BrianRiverside, CA · Jan 9, 2012#4
The white rubber piece goes inside and sits against the reflector bowl. Then the locking washer and nut secure it from the back. You can go without any of the locking rings, washer, or white rubber piece. Check Home Depot for "Sika Fast Setting Anchoring Adhesive" and you can permanently attach the projector to the bowl. Just make sure the cutoff is straight.
SAV912Thread starterSavannah, GA · Jan 9, 2012#5
I had figured that might be where the rubber piece goes, however when I put it in there on the back of the projector, I can't seem to get enough threads through the slot in order to crank down on the locking ring.

Thank you for the sealant tip though. There is a Nissan dealer close by, I'll have to drop in there tomorrow.
BrianRiverside, CA · Jan 9, 2012#6
Previous post edited with more info that might help you out.
SAV912Thread starterSavannah, GA · Jan 9, 2012#7
Ok, here is the white rubber piece against the reflector bowl. I managed to push hard enough to get enough threads thru to crank down on the locking screw.

Picture not included in this copy

Does everything look right back here?
Picture not included in this copy

My only problem now seems to be that the little U hook that the clip that secures the bulb snaps into is bent. As seen here.
Picture not included in this copy


And now I just realized that I finally got the projector in and then forgot the backlit LEDs that presumably bolt on to the back of the projector. FUCK!! Please tell me those aren't exactly necessary, because I'm really not feeling up to taking it apart to try AGAIN.
BrianRiverside, CA · Jan 9, 2012#8
Everything looks okay to me. Not sure about the led's since mine didn't have them.
Kaotic LazagnaCentral Valley, CA · Jan 9, 2012#9
I'm sure those backlight LEDs aren't necessary, you just won't have that extra feature.
SAV912Thread starterSavannah, GA · Jan 9, 2012#10
Yeah, this is the Gen 3 kit from Garm. The projector does seem more secure with the rubber bit in the back. The LED backlights seem to have their own cords and even a controller with a 3M sticky pad on the back to place it in the engine bay or something so that you can change the colors. All of that seems a little excessive.

Hopefully things go smoother with the second projector. All of this hassle was with the first light, believe it or not. Thank you for the help, though and I'm sorry if I got angry and bagged on your how-to. Most everything else on it seems to have helped a lot so far.

-C
SAV912Thread starterSavannah, GA · Jan 9, 2012#11
So when mounting the silver ballast box in Peter's how-to, it seems to sit directly above where he mounted the black relay box. I'm on the passenger side of the car right now and I can't seem to see a second set of holes. Did he just drill the ballast directly into the strut tower?
yaris2010RSAngus, Ontario · Jan 9, 2012#12
for the pic of the back of the headlight i cut off all the "extra" stuff that sticks out so the projector nut would sit flush and screw on all the way
SAV912Thread starterSavannah, GA · Jan 9, 2012#13
I managed to get the projectors secured last night. Today is sealing the lights and getting the wiring done.

Where did you mount your silver ballast box? Do they get really hot? I briefly thought of ziptieing it down until I could find a place to bolt it in but if it gets hot enough to melt plastic, then that obviously isnt a good idea.
yaris2010RSAngus, Ontario · Jan 9, 2012#14
lmfao, my drivers side ballast is just chilling between the battery and shock tower, not secure at all, passanger side and fog ballasts are ziptied, i basically just wanna keep them away from very wet conditions and from getting tossed around.

one of my fogs ballasts slipped out of the ziptie and fell into the accessory belt and needed a new connector put on
SAV912Thread starterSavannah, GA · Jan 9, 2012#15
Ok. Thanks for the input, I feel better about just ziptieing them down now. lol, sorry if these are noob questions. I've never done a retrofit before. I saw your comment on your sales thread about painting them black though. :(

I'll see how the output is as they are now and if it's really bad, then I'll go back in there and paint them black, but I'm really fed up with taking the projector in and out because it was so difficult to get it locked down last night.
yaris2010RSAngus, Ontario · Jan 9, 2012#16
its kool

u will never get back in them lol. i used actual silicone and there is no way i was getting that apart. which kinda sucks cuz now i need to go thru the hassel of trading with someone all cuz i didnt paint the turn signal like i wanted to from the start... damn OCD lol
yaris2010RSAngus, Ontario · Jan 9, 2012#17
also did u bend the 2 parts that hold down the bulb locking bar? i had to bend mine to get them in and i had aiming issues with one of the projectors cuz the bulb wasnt sitting perfectly flush cuz i hadent bent the clips back close enough to where they were originally
Black_griffin6Atlanta Georgia · Jan 9, 2012#18
I really want to retrofit my headlights, but I want to get a spare set before I try it.
I have no experience doing anything of the sort, so i'm sure it will be frustrating. XD
SAV912Thread starterSavannah, GA · Jan 9, 2012#19
Originally Posted by yaris2010RS ↑
also did u bend the 2 parts that hold down the bulb locking bar? i had to bend mine to get them in and i had aiming issues with one of the projectors cuz the bulb wasnt sitting perfectly flush cuz i hadent bent the clips back close enough to where they were originally
Yeah, I did have to bend those but I used a pair of tiny needle nose pliers and bent them back.
thebarberGrand Rapids, MI · Jan 9, 2012#20
I cut off or took off all bit that normally hold the h4 bulb in place...had lots of threads to hold the projector on...just need a dremel
SAV912Thread starterSavannah, GA · Jan 9, 2012#21
Got everything in and snapped them back together. I haven't sealed them yet because I wanted to see if the reflector bowl thing that Yaris2010RS said was true.

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Now is it me, or are my cut offs backwards? Are these seriously RHD projectors? I thought the L was suppose to peak the other way to light road signs and keep it out of drivers eyes coming the other way.

I'm pretty disappointed right now. There are tons of hot spots off to the right and the right projector was pointed almost directly at the ground. I aimed them and it still seems like the right projector is pointing off to the right towards the bushes. There's a darker spot between the two lights just off center and they don't seem to light up the road very well at all.

Yeah, they look cool as hell but I didn't get them to look cool as hell. I got them because I drive a ton at night for work and was looking for better illumination.
BrianRiverside, CA · Jan 9, 2012#22
Those are rhd projectors.
yaris2010RSAngus, Ontario · Jan 9, 2012#23
r u sure the projectors are horizontal?
yaris2010RSAngus, Ontario · Jan 9, 2012#24
also try to put u hand over parts of the headlight to see if its the bulb making the strange affects or if its the reflective surface
SAV912Thread starterSavannah, GA · Jan 9, 2012#25
It's in correctly. There were little stickers on the projectors that said "top". As far as the flares on the right projector, I think it might be a product of them being the wrong way in. I can't seem to turn them to face more forward. The larger section of the reflectors bowl is on the right side of the right projector so I would think the flare would be towards the center, not out to the edge.

About to email Garm to see what he can do, since there wasn't any silicone in my kit either.
yaris2010RSAngus, Ontario · Jan 9, 2012#26
didnt think the kits came with silicone

thing i noticed with the "top" marking is because of the way out entire headlight sits on the car if u put top to top when the headlight is out of the car when u put them in they will be lopsided. i mounted my headlight many times to take them off again and adjust the position.

for your right side projector if ur sure its not reflection it could be if u didnt tighten the nut all the way (it got stuck on something and felt tight) it could yeild that result. i had issues with mine binding on something and being a PIA to tighten
SAV912Thread starterSavannah, GA · Jan 9, 2012#27
I'll check it again. I had seen 'thebarber's write up on the MI forums and he said that his kit came with silicone. Peter's how-to says that he pulled all the old silicone out and resealed it with silicone, although it doesn't say that his was provided to him. I'll find out, but regardless I'm glad I didn't reseal them yet since they are the wrong projectors.
yaris2010RSAngus, Ontario · Jan 9, 2012#28
i doubt garm would send u RHD projectors, i doubt he even carries RHD projectors. that seems odd.

as a trouble shooting process if u can i would recommend pulling out the entire projector and plugging it in and hold it and aim it at a wall/car/fence/garage just to check the cut off line. this would determine if its the install or the housing being reflective or the projector

as for the barber supplying silicone now im mad, lol i never got any silicone from him! lol, maybe if i had used his silicone i would be able to re open my lights now vs trading them.
SAV912Thread starterSavannah, GA · Jan 9, 2012#29
Barber has his own kits, which I was unaware of. That's probably why he 'used the silicone provided'. I was confused because it was the same kit that Garm sells.

Edit: This was the cause of my confusion.
Originally Posted by thebarber ↑
ill keep that in mind, but the projector kits come with sealant
yaris2010RSAngus, Ontario · Jan 9, 2012#30
i got barbers kit and i didnt get no silicone......lol, just normal homedepot silicone will be great
cali yarisCanoga Park, CA · Jan 10, 2012#31
Sorry I missed this. If you have to buy sealant/silicone, I will reimburse you. There should have been a little tube of it with the kit.
cali yarisCanoga Park, CA · Jan 10, 2012#32
i doubt garm would send u RHD projectors, i doubt he even carries RHD projectors. that seems odd.
correct, I don't have those. all made for LHD cars.
cali yarisCanoga Park, CA · Jan 10, 2012#33
I got them because I drive a ton at night for work and was looking for better illumination.
I'm sorry for the trouble, but I'm pretty sure we never said these would light up the road better. I will check the product description though:

Projector HID kit H4, bi-xenon. This is a complete kit for the conversion of H4 headlights to a projector HID headlight.
RETAINS LO/HI BEAMS (BI-XENON)
WHITE or BLUE HALO
6000K SUPER WHITE COLOR
NEW! GEN 3 includes rear 7-color LED!

INCLUDES:
PROJECTORS
BULBS
WIRING HARNESSES
DIGITAL SLIM BALLASTS
SILICONE TO RE-SEAL HOUSINGS
FREE shipping (48 USA states)
SAV912Thread starterSavannah, GA · Jan 10, 2012#34
It's ok. I e-mailed you at MI, Garm. I suppose you can disregard it. The orientation looks so like RHD projectors when looking at the cut off but I'll just have to open them up and play with them like Yaris2010RS had suggested.

I stated this in the email as well, but I'm not disputing the quality of the projectors. They seem well made and put light out like a muhfucker. It's the project of the conversion that sucks. I'll have to see why the cutoff looks so reversed when I'm absolutely certain the position of the projector marked 'top' is in there the way it should be. I'll check bulbs and all that though.

As far as silicone, I used the parts number that Brian suggested for the Nissan silicone. They quoted me $28.XX for it at Vaden Nissan. I'm sure Home Depot has something cheaper than that.

Nokya Yellows work great though! 😁
SAV912Thread starterSavannah, GA · Jan 10, 2012#35
Originally Posted by cali yaris ↑
I'm sorry for the trouble, but I'm pretty sure we never said these would light up the road better. I will check the product description though:
You didn't, no. Your site doesn't either. It is no fault of yours. I even read a few things suggesting that projectors and HIDs don't actually light up the road better.

The overwhelming majority that do these conversions HAVE said that, though. And that's what I was hoping was the case for me as well. Don't worry, I'm not going to slander you for false advertising. I tried something, it didn't come out as expected, and it's possible that it's my own worksmanship that lead to that, and I will do what I can to fix it.

You or MicroImage is not at fault and I still enjoy and appreciate the other items that I have purchased from you. 🙂

-C
cali yarisCanoga Park, CA · Jan 10, 2012#36
I still want it to be right, though. I'll pull a kit and point the projectors at a wall tomorrow -- maybe we can resolve the RHD/LHD part first.

I've sold about ten of those kits and never heard of them having incorrect orientation for USDM cars. But you never know.

Ultimately, I would want them back and refund you if they don't work as expected. That should be the policy of any business and it's how I would want to be treated.
Kaotic LazagnaCentral Valley, CA · Jan 10, 2012#37
Your provider could have accidentally mixed in a RHD box with your shipment by mistake. Honest mistake I think.

*edit: this post is meant for Garm
Kaotic LazagnaCentral Valley, CA · Jan 10, 2012#38
I have the G1 projectors, which provide lower light output than the G3's. Here is what they look like with the provided 6000k bulbs.

At start up and warming up
Picture not included in this copy

Picture not included in this copy

Picture not included in this copy



Cutoff (yes, I purposely aimed it so that it looks like stairs going up towards the right; I'm assuming yours looks like it would be to the left if you "stacked" the cutoffs?).
Picture not included in this copy

Picture not included in this copy


Comparing it to a stock 08 or 09 Mazda6 (stock HIDs)
Picture not included in this copy


The Mazda6's cutoff
Picture not included in this copy

Picture not included in this copy
SAV912Thread starterSavannah, GA · Jan 10, 2012#39
Ok. Please let me know what you find out. Either here or by e-mail.

This is the box, just in case. The orientation of the cut offs on the box is correct:
Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

-C
Kaotic LazagnaCentral Valley, CA · Jan 10, 2012#40
If your cutoff looks like the picture on the box, then you have the correct, LHD cutoff.
SAV912Thread starterSavannah, GA · Jan 10, 2012#41
Kaotic:
Yeah, my 'stairs' go the other way. And I got flashed a ton from oncoming drivers on just a short drive down to the gas station and back. I then lowered the left a little and the right is raised nearly all the way up.

Even if I get the correct aim and all, I suppose part of it is that it just takes getting used to. I've never had a car with HIDs before and the division between light and darkness is much sharper than with traditional halogens where it kinda fades to darkness.

Edit: It doesn't. My cut off picture is a little further up the thread. Even Brian said that mine look like RHD cutoffs.

-C
Kaotic LazagnaCentral Valley, CA · Jan 10, 2012#42
Ah, I missed that post, but yes, those are definitely RHD cutoffs. You'll get flashed no matter what if you aim them to have usable light.
Kaotic LazagnaCentral Valley, CA · Jan 10, 2012#43
Originally Posted by SAV912 ↑
Kaotic:
Yeah, my 'stairs' go the other way. And I got flashed a ton from oncoming drivers on just a short drive down to the gas station and back. I then lowered the left a little and the right is raised nearly all the way up.

Even if I get the correct aim and all, I suppose part of it is that it just takes getting used to. I've never had a car with HIDs before and the division between light and darkness is much sharper than with traditional halogens where it kinda fades to darkness.

Edit: It doesn't. My cut off picture is a little further up the thread. Even Brian said that mine look like RHD cutoffs.

-C
And that division is due to the projectors (and the cutoffs inside them) and not HIDs themselves. It does take some time getting used to though. lol.
thebarberGrand Rapids, MI · Jan 10, 2012#44
My projectors have the same cutoff....but it looks to me like they're sitting crooked in the headlights...the base gap of the halo ring should be pointing down...

The setup illuminates the right side of the road more at night.

The manufacturers stopped including sealant last year as they were getting hassled by customs
SAV912Thread starterSavannah, GA · Jan 10, 2012#45
I looked into the flare problem earlier tonight here at work since I had an area with a building wall to see where light was being thrown and it appears that Yaris2010 was right. The reflectors bounce a portion of light to the outsides if they are left unpainted. I only have my cell camera on me but i tried capturing the reflection causing the flare.

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Notice the speed limit sign ahead on the left illuminated, yet the stop sign closer and to the right remains fairly dark.
Betriventedmonton · Jan 10, 2012#46
Is there any way you can rotate the entire projector the 20 degrees or so required to manuall make it kick up on the right instead?
SAV912Thread starterSavannah, GA · Jan 10, 2012#47
It might be possible with work, but then the halo would be off. I'm not sure just rotating it would fix it alone. It's worth a try I suppose.
Betriventedmonton · Jan 10, 2012#48
I wouldn't personally mind the halo being off, having it at a slight angle would look pretty cool I think
Kaotic LazagnaCentral Valley, CA · Jan 11, 2012#49
That's odd since the reflector bowl is designed for LHD cars so it should just throw the beam back towards the right????
BrianRiverside, CA · Jan 11, 2012#50
Originally Posted by Kaotic Lazagna ↑
That's odd since the reflector bowl is designed for LHD cars so it should just throw the beam back towards the right????
No. The reflector bowl should have no effect on the light if using a projector. The projector should control all of the light output by itself. If the light coming out of the projector is hitting the reflector bowl then the projector may need to be moved out more to allow it to do its job.