Yarisworld Archive

Stickerbombing dash pieces!

173 posts · 63,471 views · page 4 of 4

Replies continued

mr_milesThread starterPortland, OR · Mar 18, 2012#151
Plooonk! 1.5....you never told me where and what stickers you got!

Picture not included in this copy
ROCKLAND TOYOTAROCKLAND COUNTY NY · Mar 19, 2012#152
Originally Posted by 1.5 ↑
Just put in an order for a ton more stickers.
IM already tired of mine......🙁
mr_milesThread starterPortland, OR · Mar 19, 2012#153
so cover them up again! lol. i need to find a bunch of automotive stickers, and a bunch of Japanese stickers. got some ideas.... also, here we go - installed! very happy.

Picture not included in this copy
ttr125fan09corpus christi, texas · Mar 19, 2012#154
how do you get the pillar out?? very carefully i presume...
mr_milesThread starterPortland, OR · Mar 19, 2012#155
It pops right out. Grab it at the top and pull towards the passenger side and out it comes :)
cksandbergMinnesota · Mar 28, 2012#156
Love the Cheech Wizard!
mr_milesThread starterPortland, OR · Apr 12, 2012#157
Big update since I'm lazy and only do the MI thread, lol....

AOOOOGAAA HORN! 110 decibels of pure retro awesomeness.
Picture not included in this copy

Ghetto held on tach - currently in the gauge pod as I'm working on ways to mount it to the dash how i want.
Picture not included in this copy

annnnnnnnnnnnd coilovers! finally ordered them. big thanks to Both Garm and Jeff. :)

Picture not included in this copy

Picture not included in this copy
chewychewbaccaLong Beach, CA · Apr 12, 2012#158
holy shit your ride is lowwww
mr_milesThread starterPortland, OR · Apr 12, 2012#159
nonsense, there's still a gap on the wheels! :)
1.5Tampa · Apr 12, 2012#160
I like that mentality ^
why?harnett county NC · Apr 12, 2012#161
i wish i lived in a state that didn't think Italy is the way to go when it comes to car mods.
DeathBeardLos Angeles, CA · Apr 13, 2012#162
awesome
mr_milesThread starterPortland, OR · Apr 14, 2012#163
yayyy, tinkering today with the car, might as well post what I did. Talked to Jeff today about my getting stuck in reverse issue - suggested i adjust the shifter cable, but i couldn't quite figure out how. so while i was in that area of the car...... I ran my amp's power cable! Don't worry, it's not plugged in battery side, yet. I made a small hole in the heater hose grommet, and fed it through there, then zip tied it up out of the way, and then down through the center console.

Picture not included in this copy

then since I was bored, i started cleaning the engine bay up a little bit. removed some of the nasty electrical tape and other wire shielding, and replaced it with the loom. also removed all the foam on the hoses, it was stained and blotchy. then i went over a majority of my wiring and removed all the excess plastic clips and organized / routed it, and started replacing the wire loom that was bad. i need a lot more.

tomorrow I'm going to remove the bolts for the engine cover, and start sanding the valve cover down to remove the spots. then a quick spray of engine bright, a splash of water, and some tire shine to prep her for the warm weather of hoodless driving! (and then the fiberglass hood from garm)

Picture not included in this copy

Picture not included in this copy


here's a better shot of the horn, btw :)

Picture not included in this copy
jpmck03USA · Apr 14, 2012#164
Originally Posted by mr_miles ↑
... i started cleaning the engine bay up a little bit. removed some of the nasty electrical tape and other wire shielding, and replaced it with the loom. also removed all the foam on the hoses, it was stained and blotchy. then i went over a majority of my wiring and removed all the excess plastic clips and organized / routed it, and started replacing the wire loom that was bad ...
That looks good, man! I just removed my engine cover the other day and now I realize that it doesn't look as good as I thought it did.

Maybe I need to tidy it up as you did. 👍
mr_milesThread starterPortland, OR · Apr 14, 2012#165
popy costa from micro-snausages!

Bye Bye 522's, Hello D2's! I was kind of torn about that until i mounted them. They fit perfect! almost flush with the fenders. a little rolling and moar low, and it'll be tuckin' like mad.

clean clean clean. gotta get some strong cleaner to do the insides, looks like a CV boot tore and flung grease all around one.

Picture not included in this copy

Picture not included in this copy
mr_milesThread starterPortland, OR · Apr 25, 2012#166
Wired my sub in the rest of the way, and it turns out it's blown. so....no sub for a while. just picked up a 300 zx that has a 8 inch bazooka, thinking about putting the 12 in that, and the bazooka in the gnar gnar. will post pics of the new car in here maybe.


also brought the Gnar to a body shop to have the front end looked at, they guy was very reluctant to say anything other than "we need to do an alignment" so....will try another place.
mr_milesThread starterPortland, OR · May 1, 2012#167
Ok! mini DIY carpet removal - sub install - currently covering sub in stickers!

Heres a starting picture, i undid the rear seat belts at the bottom already, oops! you have to remove there to pull the carpet.
Picture not included in this copy

next we undo the seats! Don't forget to unplug the sensors!
Picture not included in this copy
Picture not included in this copy

lookie, sub wiring. we'll get more into this part later. begin wondering how you were able to drive with this much dirt under your seat. contemplate cleaning seats.
Picture not included in this copy

remove the bottom part of the front seat belts, now. 14mm just like the rears.
Picture not included in this copy

start gently pulling up carpet, careful now!
Picture not included in this copy
Picture not included in this copy

annnnd, don't forget to unbolt the gas lid lever. i did! :p
Picture not included in this copy

Pull the rear vent things, too!
Picture not included in this copy

Ok, now that we're up to the front seat area, be careful! there are little plastic clips holding your carpet in. So pull the running board plastics off, its pretty easy. gently pull up from the back, and pop! out they go.
Picture not included in this copy

now pull gently, and out comes the carpet! yay!
Picture not included in this copy

Eww. gross........now is when you start getting unhappy.

especially if you aren't the original owner of your car. Dog food? Cereal? YUCK. start audibly cussing at the PO of the car, so neighbors can hear. this part is optional, but highly recommended.
Picture not included in this copy

begin finding things you lost previously, like dampening adjusters.
Picture not included in this copy

Start getting aggravated even more, this is gross, i swear i would never let my car get - hey, is that change? SWEET!
Picture not included in this copy

pull foam stuff and Styrofoam pieces, pull the styrofoam gently. it could break! Assemble stuff you found in neat little pile.
Picture not included in this copy
mr_milesThread starterPortland, OR · May 1, 2012#168
Use one of these. Everywhere.
Picture not included in this copy

Next, we grab our favorite cleaner. I like this stuff. SCRUB LIKE THE FATE OF A CIVILIZATION DEPENDS ON YOU. Get to your level of cleanliness. I ran out of dry weather, so i hurried.
Picture not included in this copy

Use the shop vac again. maybe even a third time. Put seats back in.
Picture not included in this copy

Apply floor mats. These came from some sort of jeep. Friend works at infinity, and they were going to throw them away after servicing it, guess he replaced them with weathertech or something.
Picture not included in this copy

thats that!


Now onto my sub install, quite pleased, i must say. Going to be covering this in things, maybe even stickers! Who knew?

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy
1.5Tampa · May 1, 2012#169
Man our tastes are too similar. Stickerbomb'd/gutted interiors/and now a bazooka tube which I want too lol
mr_milesThread starterPortland, OR · May 1, 2012#170
I've never used a real bazooka tube until i got this one out of the Fairlady, I am super happy with it. Fits the yaris well, since I like the clean look, no amp to be seen!
mr_milesThread starterPortland, OR · May 1, 2012#171
Picture not included in this copy

Plonk.
mr_milesThread starterPortland, OR · May 14, 2012#172
Picture not included in this copy

most of the interior is back in now, too. all that's left is to cover the headliner, and it'll all go back in.

and, now for today's update.

Was in a good mood, so I started tinkering with the Gnar. :)

Painted my oil filler cap. Best piece I've painted so far, I'd say. Came out perfect.
Picture not included in this copy


Re-located my license plate, looks ok I think. Might move it, not sure.

Picture not included in this copy


Installed this switch - seems the Kenwood head unit I have likes to get stuck on "reading" instead of playing my Ipod every now and then, and the only way to fix it is to unplug the stereo. Installed this switch on the 12v constant, so to reset the stereo in case of said issue, shut car off, flip switch, restart car :) I'm trying to figure out what causes this issue, wondering if it's my Ipod, or if the little surge of power it gets when you start the car is the issue.

Picture not included in this copy

Fun day. Oh, I rotated my tires too(hooray?). Tried re-installing my fender liners. No go, guess I'll have to custom make some.
mr_milesThread starterPortland, OR · Jun 20, 2012#173
how about some copy pasta's from MI!

Welp, I've been slacking. still haven't finished the pieces I started the other day. I did however, put some stickers outside, to make fun of a certain crowd of people, lol.

Picture not included in this copy

Picture not included in this copy

There's a blue lowered Yaris HB around my area too. dark tinted glass and dark wheels. gotta find the guy. I have competition ;_;

so, i ripped my middle tie brace out. here, have a pic.

Picture not included in this copy

easy enough to spot where I hit......wait...that's not normal. this bolt wont come out?

Picture not included in this copy

hey wait....that belongs on the frame! so yeah, there we have it.. no more center tie brace for me! lol.

also - I removed my rear perches today to level out the back of the car a bit more, and i see this. was i supposed to mount these on top of the spring, not on the bottom? I noticed that they seemed to sit in there at a slight angle because of how the axle is designed. the adjusters still go on so that's a plus....if i ever use them.

Picture not included in this copy