Yarisworld Archive

Problems Mounting Tweeters

12 posts · 4,591 views

HardicusOriginal postGold Coast, Australia · Oct 29, 2011#1
Hi all,

I recently purchased some Alpine Type G components for my Hatchback, and i'm struggling to figure out how i'm going to mount them. I've seen lots of pics on this and other forums where people have mounted them in the door handle like this:

Picture not included in this copy

I assumed this would be the easiest course of action, as everything I've seen basically states that you just need to drill a hole in that one piece of trim. I have zero experience with car audio, but this seemed like the best option, as it also meant all the wiring was contained to the door, and I didn't have to mess around with the A-pillar which has an airbag in it.

So I went out to check that it really was going to be this simple, and this is what I came across.

Picture not included in this copy
So this is the piece of trim where I intend to mount the tweeter, all good, so I take it off...

Picture not included in this copy
...and this is what's underneath. Now, if I were to try and mount a tweeter in this position, then I'm obviously going to have to drill through this section too. Nowhere in anything I've read have I seen any mention of this. I just assumed that there was empty space behind the top panel. How would I drill/cut a hole through this? Does it matter if I have to mangle and make some of the clip holes unusable?

Picture not included in this copy
A picture of the tweeter in the position I'm intending to mount it. It looks like cutting through this section would be pretty difficult without a dremel. Any suggestions for alternative ways?

The other option I guess is to mount it in the A-pillar, but I'm really not keen on that.

Can anyone who has done this same install comment on how they managed to do this. Was cutting required? Am I missing something obvious?

Thanks very much for you time.

Replies 11

HardicusThread starterGold Coast, Australia · Oct 30, 2011#2
Hmmm I did an extensive search before I posted this, but only just now ran across this thread:

tweeters in door

Shows what I want I think. Still curious on what would be the best tool to gouge out that section though.
bzinn 1University Place,WA · Nov 12, 2011#3
I would use a 2" hole cutter with a drill and cut through the under panel.
AltitudeColorado · Nov 12, 2011#4
Originally Posted by bzinn 1 ↑
I would use a 2" hole cutter with a drill and cut through the under panel.
This.

I did this in mine and I would recommend removing the entire door panel. Leave the top cover piece on when you drill through. You should be fine with the clips. I even mounted mine further towards the front and it was fine.
cali yarisCanoga Park, CA · Nov 13, 2011#5
^ same here
HardicusThread starterGold Coast, Australia · Nov 13, 2011#6
Thanks all, I got around to it on the weekend. Ended up using a stanley knife to cut through the underpanel. It looks pretty good, only problem is my tweeters don't sit quite flush due to that panel being slightly curved. I don't know how to fix it, but it's good enough for now, until it bugs me enough to try and glue them down or something.
sqcompBack at home · Nov 13, 2011#7
Mmmm...that's the rub. You've got to know the surface you're mounting on. You COULD cut out a larger rectangle-ish area to make room for a flat baffle to mount the tweeters on. By then though, you might as well have put them in the a-pillars with all the work you're going to do to make it look nice.

A pillars are a better location anyway due to PLDs.
HardicusThread starterGold Coast, Australia · Nov 14, 2011#8
Yep gotta say I chose this location cos of ease of installation, but having done it, i'm pretty certain the A pillars would have been easier.
Betriventedmonton · Dec 29, 2011#9
Sorry for bump.. but if you still have an issue with the gap you could find a rubber grommet/gasket and put it between the tweeter and the panel piece.
yojabbajabbaMelbourne · Dec 30, 2011#10
Originally Posted by Betrivent ↑
Sorry for bump.. but if you still have an issue with the gap you could find a rubber grommet/gasket and put it between the tweeter and the panel piece.
... great idea! I'm thinking of mounting the tweeters in the A-pillar, thanks for the tip!
👍
swiddCentral Alabama, GOD BLESS AMERICA · Dec 30, 2011#11
lol... good times. I didn't have a drill at the time, so I used some old knives I didn't care about...heated the knife on the gas stove and melted a hole in the plastics. Had to disable the smoke alarm as it blasted off, but turned out good in the end.
Betriventedmonton · Dec 30, 2011#12
How does the wiring for a tweeter work if I wanted to DIY? I've been looking into this for a bit now