Yarisworld Archive

Yet another Blitz Supercharger Install

63 posts · 118,134 views · page 2 of 2

Replies continued

CTScottThread starterUSA, CT · Jan 14, 2013#51
Originally Posted by TOLMACH ↑
Background: Checked e-bay to discover that there is a bunch of different ECUs available for 2006-2012 yaris. Mine is 89661-52j30 version (canadian 5 speed manual tranny).

Question: Do I just wire the CS controller same way as shown in the post below?

http://www.microimageonline.com/foru...ll=1#post14467

Thanks

P.

All of those ECMs are the same from a SC standpoint. The differences are for tranny type, engine immobilizer, ABS equipped, etc.
cali yarisCanoga Park, CA · Jan 14, 2013#52
^ Blitz used to mark the fuel controller for manual or auto transmission, though. I have no idea what the difference in tuning might have been.
CTScottThread starterUSA, CT · Mar 11, 2013#53
Originally Posted by TOLMACH ↑
Question pls re wiring .. (I know I am very slow)

My question deals with clutch activation

1. I am right in thinking that blue wire on the diagram is simply supplying +12V signal to the relay (this wire goes from the 4-position module which manages the whole activatio thing)?

2. and that If I wire this unit only (wihtout connecting the fuel controller and 4-position module ) and supply +12 v to the blue wire I will be able to check whether clutch is engaging (just wanted to check the sc unit itself prior to installation as my kit is a pre-owned one)

Thank you

P.
The blue wire from the cabin switch is actually the switched ground for the relay coil. If you look at that diagram above you will see that fused power goes to the relay coil and then the blue wire from the switch goes to the other side.
CTScottThread starterUSA, CT · Mar 11, 2013#54
Originally Posted by TOLMACH ↑
Thanks.. meaning that in there is @nothing@ in this blue line then SC is not activated, and if positive (12+v) goes to blue wire, SC gets activated?
No. It is a switched ground, so when the blue wire is connected to nothing the SC is not activated and when the blue wire is grounded the SC is activated.
jcboyAsia · Mar 13, 2013#55
Originally Posted by why? ↑
You get less gas mileage because the supercharger is always going ( well not always, as the blitz does have a clutch) and a small turbo tuned right can do the same thing a supercharger can but get better gas mileage and more power. It would just cost more. And be more of a hassle.

But Philippines? isn't that the land of dirt cheap labor costs?

Well, commodities and services cost a lot there in the US, but you earn big money too. Here commodities and services are dirt-cheap compared to there, but people earn a looot lower than people there. Although the cost-of-living-to-salary ratio is lower compared to what you have, unfortunately it is still not considered affordable since as non-necessities such as car tuning (as compared to house repair) are charged incredibly high.

FYI, A decent paint "washover" can go as low as $500 including labor and paint and all. a $600 paint job is already superb, an $800 paint job is carshow quality already, probably with pocket change.
CTScottThread starterUSA, CT · Mar 20, 2013#56
That wiring is all correct for the Yaris. How did you make your connections (tap splices, solder, etc.)?
CTScottThread starterUSA, CT · Mar 21, 2013#57
Originally Posted by TOLMACH ↑
Update: Just disconnected a bunch of wires and reconnected the same way again: IT WORKS.. dunno what happened

JEEEEE... THE CAR FEELS TWO TIMES FASTER!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
CAN NOT BELIEVE HOW GOOD THIS THING IS!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
That's great that it is now working. I would recommend either soldering the connections or using some form of crimped connectors. Twist and tape is not a good way to go under the hood.
CrankyOldManWest Michigan · May 7, 2013#58
CT, do you by chance have any pictures of your soldering process? I'm not 100% sure how to strip the insulation on the OEM harness w/out cutting any of the wires. Small torch?

I soldered the lights on my trailer last weekend and it was a pretty big pain trying to hold both wires steady enough to get the solder to set. In addition, I ended up cutting the wire that was being spliced in to so that I could get the heat shrink over just those two wires. There were a few stray strands that got nicked by the wire stripper, but I'm not as concerned with trailer lights as I am with the ignition wiring.
CTScottThread starterUSA, CT · May 7, 2013#59
Originally Posted by CrankyOldMan ↑
CT, do you by chance have any pictures of your soldering process? I'm not 100% sure how to strip the insulation on the OEM harness w/out cutting any of the wires. Small torch?

I soldered the lights on my trailer last weekend and it was a pretty big pain trying to hold both wires steady enough to get the solder to set. In addition, I ended up cutting the wire that was being spliced in to so that I could get the heat shrink over just those two wires. There were a few stray strands that got nicked by the wire stripper, but I'm not as concerned with trailer lights as I am with the ignition wiring.

I didn't take pictures of that process, but I typically do inline soldering by either of two methods:


Stripping the wire:

1. Strip and smush - Take the wire to connect to, cut through the jacket with a wire stripper (one that has separate holes for each wire size, to prevent cutting the strands). Once you are through the jacket, push the stripper along the wire towards the longer side of the wire (i.e. away from the nearest connector). You can typically get 1/2" to 1" of access to the bare wire by doing this.

2. Carve the insulation - Using a hobby knife (or the stripper above and hobby knife), ring the insulate at two points about 1/2" apart, and then slit between the two rings to remove the section of insulation.


Soldering:

Wrap your wire to attach around the exposed wire, heat the two wires with a soldering iron, and wick the solder into both. Then, a wrap of electrical tape or a shrinkable tape seals the deal.
CrankyOldManWest Michigan · May 8, 2013#60
^Now that you mention it, I think I have one of those around here...
CTScottThread starterUSA, CT · May 9, 2013#61
Originally Posted by TOLMACH ↑
^ I think this thing can also help prevent (to some extent) the heat from going towards the ECU and potentially damaging smth.. My soldering skills are kinda mediocre - overheating the wires is a real possibility ((
You won't really have enough room to use a tool like that, but there are no real worries about overheating the wire. You will be splicing into the wire a few inches from the ECM connector and can even do so with it unplugged...
tmizellFlorida · Aug 24, 2025#62
@TOLMACH Thanks for sharing that diagram. Saved the day!
Was shipped a used Blitz with the NCP91 kit, but has the xB Fuel Controller. Couldn't find the proper wiring diagram, until I found your old post.
612 YarisCalifornia · Aug 27, 2026#63
If you ever want to sell it , let me know