Yarisworld Archive

DIY: 2006-2011 Yaris OEM Cruise Control Complete Installation

147 posts · 311,598 views · page 3 of 3

Replies continued

David CMontreal · Aug 9, 2016#101
Originally Posted by bassmannate ↑
Well, I got a chance to meter the switch finally. Getting 1.5-2 ohms when the on/off button is pressed. Not sure if that's so high that the ECU thinks that it's not ground. I suppose if there's any other resistance such as oxidation on one of the pins between the switch and the ECU it would bump that resistance up and it wouldn't know what to do with it.
Try to read the resistance between the main chassis ground next to the battery and the battery terminal itself, then compare it to the reading you're getting between the ground connection you're using for the stalk and the battery terminal. Subtract the main ground to terminal value to it and that's how much resistance that you should try to reduce. I would assume the ECU has a direct wiring to the battery terminal clamp, but the manufacturer would take for account the resistance in chassis ground when setting the value range for the CC inputs, since the stalk would be connected to chassis (same connection as the horn by connector D3, right ?).

I did the readings on my own setup (I used 2x 2-way rocker switch and connecting my ground to the bolt behind the kick panel under the steering wheel) and had a lot of resistance using that ground point compared to the main chassis ground, but still I have flawless operation so far (installed it and been using it daily for 5 days now).

However I would really doubt that the switch internal resistance of less than 2 ohms would throw every off. It sounds more like a bad contact inside the ON/OFF switch, otherwise you wouldn't be able to use all the other function flawlessly.
CTScottThread starterUSA, CT · Aug 9, 2016#102
Originally Posted by bassmannate ↑
Well, I got a chance to meter the switch finally. Getting 1.5-2 ohms when the on/off button is pressed. Not sure if that's so high that the ECU thinks that it's not ground. I suppose if there's any other resistance such as oxidation on one of the pins between the switch and the ECU it would bump that resistance up and it wouldn't know what to do with it.
That is fine. There is about 30 ohms of tolerance for each of the switch modes.

Was the ECM pin a genuine one that seated properly in the ECM connector?
bassmannateCrystal Lake, il · Aug 9, 2016#103
Originally Posted by CTScott ↑
That is fine. There is about 30 ohms of tolerance for each of the switch modes.

Was the ECM pin a genuine one that seated properly in the ECM connector?
Pretty sure it seated properly. It felt like it clicked in there. I'll try to pull it out again tomorrow morning and make sure it seats correctly. I would think if that were the issue the rest of the functions wouldn't work right.

Sent from my LG-H811 using Tapatalk
CTScottThread starterUSA, CT · Aug 9, 2016#104
Originally Posted by bassmannate ↑
Pretty sure it seated properly. It felt like it clicked in there. I'll try to pull it out again tomorrow morning and make sure it seats correctly. I would think if that were the issue the rest of the functions wouldn't work right.

Sent from my LG-H811 using Tapatalk
The other one will only work after on/off works, so unless you can watch the cruise control input on a Toyota Techstream tool, you really can't tell if the other functions are working when on/off is now.
bassmannateCrystal Lake, il · Aug 9, 2016#105
Originally Posted by CTScott ↑
The other one will only work after on/off works, so unless you can watch the cruise control input on a Toyota Techstream tool, you really can't tell if the other functions are working when on/off is now.
Right but after i get it on, everything works great. I used it from Chicago to St. Louis and back this past weekend to keep pace with traffic.

Sent from my LG-H811 using Tapatalk
bassmannateCrystal Lake, il · Aug 9, 2016#106
Well, I think I figured out what the problem is. I went ahead and pulled the ECM plug back out and checked it out. On closer inspection, the wire that came with the kit does not have the little rubber piece that goes directly behind the pin. This piece not only looks like it seals out moisture, but also locks the pin more securely than the pin lock mechanism does on it's own.

This would explain why it worked flawlessly right after I finished the install because the pin had just been seated. Add on top of that that I didn't have any zip ties for a couple days to re-secure the ECM wires and it was a recipe for that pin to vibrate out slightly.

Anyone know what that piece is called? If I can get a picture, I'll post it to show what I'm talking about. Where would I find these?

Edit: I found a picture. It's the blue piece right behind the pin on the yellow wire.

Picture lost · dl.dropboxusercontent.com
badPennsylvania · Mar 3, 2017#107
I was looking at this pdf. Looking at the picture of the cruise stalk on page 2, does anyone know if that one wire with the brown connector is actually used?
NYC-SENYC · May 9, 2017#108
Thank you for that very well documented step by step video. I'm sure it will help out others in the future.
scratchpaddyPhoenix · Jun 4, 2017#109
They are M5 screws. Any hardware store will have them. The shortest ones you can find should do fine.
laobovietnam · Aug 11, 2017#110
Originally Posted by Mikeyh ↑
Scott,

Thanks for the cruise control kit for my 2014 Yaris L. Just as you said, it was easy to install, really plug and play. Took about 20 mins. and the wiring you included for stalk and horn wire made connections simple.

If I can do it anyone can! 👍

Anita (Mikey's wifey)
Dear Friend.
can you show me, pin of teminal ECM to connect from Swith CCS?
Im a yaris sedan 2014, but i not found pin ECM ( ECU) from my car. OR have you got this Diagram
Thanks!
nikonNUTHot Springs, Arkansas · Aug 31, 2017#111
Just finished my install. Why didn't I do this sooner?!? Thanks for the parts and the great tutorial Scott!

P.S. I didn't order the rear cruise rear boss. I just used this to drill the hole....
https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1

Worked a treat and no pulling the steering wheel!
n3szt0rHungary · Sep 4, 2017#112
Dear Toyota friends!

I would get some confirmation about cruise control. My Dad's birthday gift would be a cruise. He has a 2008 Auris 1.33 petrol europe(uk) engine code 1nr-fe.
Did see one of supported yaris has the same engine.
Will it fit?
Can you give me name of small metal connectors or a source for them?
Please help, thank you!
GibbsYaris07Charlotte, NC · Sep 10, 2017#113
Just finished mine this morning. The hardest parts were running the wiring and making ghetto pins. lol
FreedomageTR Istanbul · Nov 23, 2017#114
Hi I couldnt find any introduction page so My name is Alper and from Turkey.
I have a Yaris 1.33 1NR-FE Multi Mod transmission I checked my VINN number and it says that my car's market: North America, Europe(UK) by the way it is made in France.
TYPE: NSP90L-CHLGKW
I was wondering if my car's ECU has built in CC functionality.
Is there anything I can do to figure out this?
Per OlofThailand · Jul 27, 2018#115
Originally Posted by CTScott ↑
The on/off is just a switch to ground. I would check all of your connection points to make sure it isn't an intermittent connection. If the stalk is one of the Chinese clones, it could be a bad switch within it as well.

I do still sell the indicator modules.
Hello Im new in forum,I have Yaris G mod. 2014 5dor. aut. smart entry&start system and want to have CC. Im swedish but live in Thailand.How can I tjeck if it possible to put it in my car.The car seem to have a diffrent ECU (ECM) It spli to 2 units behind the glove compartment.If you know about this,can you sell me one to me ??
tiiamsDexter, NM · Nov 26, 2018#116
Mine has been working great for 7 years or so i forgot when I bought it. Thanks scott only issue is blue light gets confused in cold weather. but functionality is perfect. By the way I am at 238,000 mile approx.
MykalSt George, UT · May 8, 2020#117
Hi Scott, I purchased the OEM cruise control stalk for the Yaris, but am still in search of the rest of the parts. Do you have those in inventory? - Mykal
SumdudeFort Bragg, CA 95437 · Jul 8, 2020#118
Hi Scott,
I am new to your forum and also a new Yaris owner. I have just purchased a used 2010 Yaris LB with out Cruise Control. I have been reading some forum posts and I would like to know if you sell the complete CC kit and if so, how do I order it?
Thanks for your assistance,
Sumdude
reg_accountVA · Jul 12, 2020#119
Hi all,
I just wanted to post my experience with this version of the car if anyone is interested. I have a 2010 US Sedan auto transmission with no power windows/locks, but with AC. I found a couple of interesting differences with my car that I couldn't figure out from the pdf, so I thought I would share. Big thanks to CTScott for the guide!

I was able to get the stalk from a junkyard Camry (04-09 I think, according to the other thread). I pulled off the extra wiring from the Camry and was able to pull the pins out from the larger Camry connector, which I was able to fit into the smaller connector (with the horn wire, section 1.4.3 in pdf) from the Yaris. Cost about 10 dollars for the stalk locally. If you do need to pull those wires from the Camry connector, you have to pull really hard (I thought I was going to break it) but it will disconnect if you have the lock popped up. One last thing about the stalk, I only had a 1 inch circular drill bit (Spade bit? the flat kind..) but it worked out fine. I highly recommend cutting the hole in the plastic, it is quick and easier than pulling the steering wheel.

Next, I found that the ECM pin already had a wire in it (it says this in the guide) so I was able to use a tap splice to connect to this. I precut the wires with a wire stripper to expose the wire to the splice (wasn't sure if it would cut the insulation fully). Firewall install wasn't too bad, as I was also installing a car amp wire. However, I think my grommet was in backwards, since I had to flip it around behind the carpet to pull it out.

The last thing I found was that I did not have any D3 connector pins. I found an ebay seller who makes the same wire and sells them for cheap (8 bucks shipped for 2 pins). I used some wire from the remote turn on from my amp kit (18 gauge) to connect the ECM tap splice to these D3 connectors. Make sure the pin lock snaps in easily with a nice click and you are good. I was able to see the indicator on the dash after connecting the battery and holding the ground wire to metal. Took it for a test drive today and it worked like a charm!

Quick summary:
2010 Yaris sedan, AT, no power windows or locks

Need to buy:
Stalk and wiring to horn pin (Need T30 bit to get into wheel)
D3 connectors
18 gauge wire or similar small gauge wire
Tap splice that fits your wire gauge
Butt connectors or crimp caps (I used Install Bay CC2218 since I had them)

You need a few other basic tools from the pdf, so read over it to get the gist. Thank you to all who posted on these forums about this so I could install a cruise control in my car for $21!
c-dubI think we're back in Kansas Toto! · Oct 26, 2020#120
Is there a wired connector for the clutch switch (88280-14030)?
bassmannateCrystal Lake, il · Oct 27, 2020#121
Mine has been working fine for 5 years so far. Wish I had the indicator but I get along pretty well without it.
c-dubI think we're back in Kansas Toto! · Oct 31, 2020#122
Got it installed today, took me about 5 hours, but soldered and heat shrank everything and made a harness. Found a radio harness from a 2020 4Runner (extra parts from a Alpine sub install) that had a female connector that i was able to modify for the clutch switch. Very easy install, just needed to adjust the clutch switch after the test drive. Only thing i'm not happy with is the connections in the fuse box. I need to figure out how to pull the pins, so i can get some heat shrink on them. I'm sure the tape would be fine, being enclosed and all, but it bothers me.
Neinris‘Murica! · Mar 17, 2021#123
Originally Posted by Mrdea321 ↑
Hi im
New to this forum.
How can i know my yaris 2006 supports cruise control.please tell me
Thanks
Welcome to the forum!

If I'm not mistaken 2006 is the start of the 2nd Gen. I have a 2008 2dr hatch, and I've installed a cruise control. It was really useful when I moved from Maryland to San Diego. I don't do much of a long drive here, so I don't get to use it. Now I'll be moving back in June, so I'd get to rely on it again. 🙂

I think this was the video that I followed:

https://www.youtube.com/watch?v=nxRHFkUwg60

Good luck!
Ben_SLC, UT · Sep 6, 2021#124
Does anyone have a backup of this PDF??? After 8 years of ownership I'm fed up of no cruise control
ClawbrantRochester NY · Sep 20, 2021#125
Originally Posted by Ben_ ↑
Does anyone have a backup of this PDF??? After 8 years of ownership I'm fed up of no cruise control
I second this. I thought I had a copy saved somewhere, but I can't find it.
Jithin_mpUAE · Jun 11, 2022#126
Dear TScott

Any idea cruise control work in Yaris 2008 DCC Yaris Sedan.

Hoping your valuable reply.
sh0rtlifepacific north WET · Jun 11, 2022#127
Originally Posted by Jithin_mp ↑
Dear TScott

Any idea cruise control work in Yaris 2008 DCC Yaris Sedan.

Hoping your valuable reply.
i would be highly suspect if it didnt work and i say this as ive been thru the toyota cross referance part number catalog and basicly the same part is used for everything toyota from around 2004/05 till at the very least 2011 with some exceptions running significatly longer and some running shorter..specificaly design changes
EvilthorneCanada · Jul 8, 2022#128
Does anyone have the part number for the wires we run down the column to the ECM by chance?

Trying to get CC working on a cousins car before she drives across the country with it.
EvilthorneCanada · Jul 20, 2022#129
Does anyone have the pdf for installing this cruise control by chance?
kevinj93Sydney, Australia · Jul 20, 2022#130
Yes. It's about 10 Megabytes. I have put in on Google Drive here
Don mullanixOregon · Dec 28, 2022#131
How can i get this cruise control guide for toyota yaris
sh0rtlifepacific north WET · Dec 29, 2022#132
the link in the post above yours is still good...
sh0rtlifepacific north WET · Apr 16, 2023#133
i know with an auto running the coastal range it will downshift and handle it just fine..with a manual your kinda on your own there as to wen to downshift and pop out of cruise
hypersataGCC · May 28, 2023#134
Hello there,

can anyone help me with the Aftermarket kit for Yaris 2014 GCC - Cruise control?
I cant find something useful on the internet myself.

as I discover from this forum, GCC versions are not supporting OEM CC.

any help would be much-appreciated Folks.

For the reference
NCP151L-CEPRKV
MHFBW9F36F50027xx
2NZFE 1300CC 16-VALVE DOHC EFI
En4sirNE Pennsylvania · Jul 19, 2023#135
I have a 2009 Yaris 2 door hatchback with a 5-speed trans. It has factory installed cruise control and 332,000 miles on the odometer. The cruise control recently stopped working. I've tried to activate the CC however the yellow CC light in the instrument cluster does not illuminate, nor will the CC operate. Hoping the culprit was a blown fuse I inspected all fuses - all seem fine. Then, hoping it was the CC stalk (hoped that the switch wore-out) I replaced the stalk with a brand new OEM stalk #84632-08021 Speed Control Switch. The CC still doesn't operate. I checked the original stalk with a multi-meter and the original stalk has continuous power while the stalk button is kept pressed in, but as soon as I remove all pressure off the button continuous power is disconnected. I assume that's how the on/off button in the stalk is supposed to operate(?).

I'd really like to get the CC operational again. What should be next course of action? I suspect that even if either CC disengage switch on the clutch and brake pedals are faulty, the CC indicator light on the instrument cluster would still light up. Is there a relay that powers the CC? Again, the yellow CC indicator light on the center instrument cluster does not illuminate. Other than the CC not being functional, everything else works flawlessly. Bad relay? Bad ECM? Or?...... Any advice that you may provide to restore my CC is greatly appreciated.
sh0rtlifepacific north WET · Jul 19, 2023#136
10-1 odds are its your snail AKA spiral cable, its actualy one of the hardest wearing parts on a car as your basicly bending wires back n forth every time you turn the wheel

9-10 times when a FACTORY CC fails it can be traced to 1 of 2 things, a bad spiral cable or a bad brake switch..and before you go and check if your brake lights work..remember that it has a secondary set of wires on the switch SPECIFIC to the cruise and not part of the brake lights

yet the first thing anyone replaces is the cruise stalk thinking its that....belive it or not ive yet to find one dead that wasnt physically visually damaged on the outside...fun side note is that said switch sometimes replacing it with other bad parts will give a false positive and youll have working cruise for a single use...its because you got lucky...i chased that demon earlier this year on an XB..intermitent CC working..was a combo of the spiral AND the brake switch both were intermitently bad
Jithin_mpUAE · Jul 22, 2023#137
Thank you sh0rtlife. I have received all the necessary parts. I will give it a try. :)
CrimsonEclipse. · Mar 15, 2024#138
Finally finally FINALLY getting to the CC mod

Looking at the install guide, it seems to imply that my 2011 M/T doesn't need wiring installed. Looks like it already has a clutch switch installed, and it seems that all I need to do is install the stalk.

Does that sound right?

(would be great if I can do this for $35)
GemakOrange County Ca · Mar 16, 2024#139
I have AT and followed the guides in this thread and now I have CC. Go for it, just be careful with the air bag
CarpeDiemWhitehorse · Jul 29, 2024#140
Hey guys, I got the kit today and installed the CC in a 2008 Yaris (no cruise light)...fast forward and I can't seem to get it to work. Did some troubleshooting over all connections (Pins are fully seated), checked the ground and the connection at the ECM all seem fine. When checking the voltage at D3 pin1 I have 13.3V, hold down the on/off switch and still 13.3V (not going to 0V). Could it be possible that the offshore Amazon stalk is bad out of the box? Any thoughts?

Thanks in advance
Markwelch415Northern CA · Aug 10, 2024#141
Does anyone have a link for the instructions? I can't seem to get this one to work. Thanks! In very interested in doing this!
thetutMontreal · Aug 11, 2024#142
Read post #152
BLHCT · Aug 12, 2024#143
It is in post #162
Cris_co1221Alabama · Oct 13, 2024#144
Originally Posted by CarpeDiem ↑
Hey guys, I got the kit today and installed the CC in a 2008 Yaris (no cruise light)...fast forward and I can't seem to get it to work. Did some troubleshooting over all connections (Pins are fully seated), checked the ground and the connection at the ECM all seem fine. When checking the voltage at D3 pin1 I have 13.3V, hold down the on/off switch and still 13.3V (not going to 0V). Could it be possible that the offshore Amazon stalk is bad out of the box? Any thoughts?

Thanks in advance


I am having the same issue, but a 2007 3dr manual. I have all oem parts but cc not working, and same voltage issue when depressing the on/off switch.
Cris_co1221Alabama · Oct 19, 2024#145
Originally Posted by Cris_co1221 ↑
I am having the same issue, but a 2007 3dr manual. I have all oem parts but cc not working, and same voltage issue when depressing the on/off switch.
My issue was pin #2 on d3 wasn’t fully inserted (ground wire), got that hooked up and am fine now.
scott10301Fremont, California · Jun 1, 2025#146
Just did the install today and no luck. I have a 2007 with no indicator light and want to troubleshoot to see if I'm at least the switch to the ECM is working.

How do I troubleshoot this? I saw that some are mentioning that they're testing voltage while depressing the on/off switch. Are you removing the pin from the D3 connector and then using a multimeter to test? I'm not sure how else that would be done. I did pull the pin and checked and am getting 13.3 volts whether I press the on/off button or not.
scott10301Fremont, California · Aug 11, 2025#147
Update - I found the issue. The splice connector under the hood was not set up properly. Set it up correctly and all is working well.