PETERPOOPOriginal postOahu · Nov 14, 2010#1Decided not to use the Zage oil pan. After seeing how cydgdydgdyeee explained why the Zage oil pan wouldn't work, I've decided to go a different route.
Will this 5/16" hose fitting be big enough for the oil return line? The oil line that comes with the zage kit doesn't look any bigger than a 1/4 to 5/16".
Thanks to garm for showing where to put the hose fitting. ;)
Picture not included in this copy
Picture not included in this copy
Replies 96
cali yarisCanoga Park, CA · Nov 14, 2010#25/16" should be fine. Definitely post pics of your return location when you get to it. Where did I post those? can't find 'em now.
Focus_Sh1ftNew Jersey · Nov 14, 2010#3Good call on the pan, I'm almost positive he's right.
Were you able to drill the block yourself? I really don't want to have a mechanic do it simply because I need a lift to have enough working space.
Lots and lots of pictures please sir. 😁
PETERPOOPThread starterOahu · Nov 17, 2010#4I've decided to go with a 3/8" diameter hose, because the bulk head fitting was already 3/8", just had to change the hose connection. Didn't want to drill a bigger hole in the block (time consuming).
This is what I did to drill the hole:
The tools..
Picture not included in this copy
Once the car is up on jackstands, you need to jack the axle up. As high as you can, need room to drill the hole.
Stuff rags in oil pan to prevent metal shavings from going in.
Picture not included in this copy
Starter hole...
Picture not included in this copy
After starter hole, used the step bit to get the right size for fitting.
Picture not included in this copy
The axle was in the way, so this is all the height i could get. I think it's high enough?
This is where the full mark is on the tip stick; about two inches.
Picture not included in this copy
This picture is to the bottom of the fitting; close to 4 inches. Unless I'm on a crazy hill, the oil should drip in.
Picture not included in this copy
I've tee'd off the oil sending unit and have put my oil feed line in place.
More progress will be made during thanksgiving weekend.
TamagoOff Grid · Nov 17, 2010#5buy a 90 deg fitting and a flare a tube to go to the bottom of the pan. you do NOT want that hot oil hitting anything but oil when it enters the pan... if it comes out into just air, you'll foam your oil and do damage to your engine (much like overfilling will do)
Focus_Sh1ftNew Jersey · Nov 17, 2010#6 Originally Posted by
Tamago ↑ buy a 90 deg fitting and a flare a tube to go to the bottom of the pan. you do NOT want that hot oil hitting anything but oil when it enters the pan... if it comes out into just air, you'll foam your oil and do damage to your engine (much like overfilling will do)
Ok, so whose right about this? If you have oil hitting oil, then that means your line runs right into the oil, which is going to cause it to back up in the turbocharger. I now know this from experience unfortunately.
But now you're saying oil into air causes foaming? Uh... 🤷
Thanks for the pics btw. 👍
cali yarisCanoga Park, CA · Nov 17, 2010#7Charles has his going into the Zage pan with no issues.
ShinareOklahoma City, OK · Nov 17, 2010#8Wouldn't the return line going into the bottom of the pan just back oil up into the line to the level of the oil in the pan? Any new oil coming down the line would push down a little on the level in the line and thus push up a little on the oil in the pan?
Is there no oil pressure on the return line?
Focus_Sh1ftNew Jersey · Nov 17, 2010#9 Originally Posted by
cali yaris ↑ Charles has his going into the Zage pan with no issues.
Hmm.. Is he using thicker than a -8 AN line? Also possible his banjo bolt has a smaller restricter I guess.
cdydjded, your return is setup just like PETERPOOP's at this point, right? No line on the inside of the block running down into the oil?
Originally Posted by cdydjded ↑
I look at it this way, if you looked at 1000 turbocharged cars Im sure 99% of them have the oil return above the oil line....
I'm inclined to agree. I can't see how hot oil hitting air would cause foaming. If that were the case, oil dripping down from the cylinder walls would foam, as well as the hot oil sitting in the pan...
TamagoOff Grid · Nov 17, 2010#10 Originally Posted by
Focus_Sh1ft ↑ Ok, so whose right about this? If you have oil hitting oil, then that means your line runs right into the oil, which is going to cause it to back up in the turbocharger. I now know this from experience unfortunately.
But now you're saying oil into air causes foaming? Uh... 🤷
Thanks for the pics btw. 👍
huh? you need to go pour soapy water into a pitcher and see what happens, then pour the same water through a hose into the same pitcher..
how would oil back up into the turbo because it terminates under the oil line? that doesn't even make sense..
TamagoOff Grid · Nov 17, 2010#11 Originally Posted by
Tamago ↑ huh? you need to go pour soapy water into a pitcher and see what happens, then pour the same water through a hose into the same pitcher..
how would oil back up into the turbo because it terminates under the oil line? that doesn't even make sense..
basic hydraulics will tell you to NEVER terminate any return line above the oil line. its not the oil hitting the air that causes foaming, it's the oil hitting the top of the oil. just like filling a bucket up that has soap in it. if you hold the hose above the water, the turbulence of the water landing on the top of the water will cause the soap to foam. if you put the hose under the water it does not disturb the oil..
TamagoOff Grid · Nov 17, 2010#12you miss the point. they're saying that the turbo should not sit BELOW THE OIL PAN...
PETERPOOPThread starterOahu · Nov 18, 2010#13Thanks for the info. Still not 100% sure which is best. Got to look into it more. But one thing I did decide to do, was to put a 90 coming through the bulk head, aiming down, rather than shooting straight across. After seeing the video (thanks cydgdgdgege) and seeing how strong the oil streams out, I didn't want it shooting onto the crank; and tamago's idea about putting the 90 made a lot of sense to me too. But I'm not too sure yet if I do want to extend it into the oil or not; still researching...
This is what I got so far:
Picture not included in this copy
Like tamago suggested, I could put this fitting on so the oil will return below the oil line.
Picture not included in this copy
This is with the 3/8" fitting on the outside..
Picture not included in this copy
TamagoOff Grid · Nov 18, 2010#14looking good sir
Bluevitz-rsOshawa, Ontario, Canada · Nov 18, 2010#15So then, what's the point of putting a hole in the block so high? Why not just put it just below the level of the oil in the pan to begin with.
The laws of equalization should apply to any liquid fluid. No matter what the hight of the return line in the oil, the levels will always equalize out. Even if the return was taped underneath the pan. The whole problem with the Zage return was that is was too restrictive running it all the way to the front.
The return line on my old Greddy kit was in the back of the oil pan and I experienced no problems with it at all. But it ran straight out the bottom of the turbo and into the pan. No bends anywhere. (I can post a picture of it later...)
Focus_Sh1ftNew Jersey · Nov 18, 2010#16 Originally Posted by
Bluevitz-rs ↑ So then, what's the point of putting a hole in the block so high? Why not just put it just below the level of the oil in the pan to begin with.
The laws of equalization should apply to any liquid fluid. No matter what the hight of the return line in the oil, the levels will always equalize out. Even if the return was taped underneath the pan. The whole problem with the Zage return was that is was too restrictive running it all the way to the front.
The return line on my old Greddy kit was in the back of the oil pan and I experienced no problems with it at all. But it ran straight out the bottom of the turbo and into the pan. No bends anywhere. (I can post a picture of it later...)
I completely agree. I had trouble digesting cdydjded's explanation (especially after Garm confirmed Charles is using the Zage pan without problems) but I'm not ready to accept a problem with the seals (which apparently are more hardy than they seem).
Watching those YouTube videos, I was pretty surprised at the velocity of the return oil. But that also leads me to believe that the orientation of the return line isn't that big of a deal, as long as it doesn't dip up. Oil flowing at that velocity should just push it's way through the line... It's probably worth mentioning that (for me atleast) there is very little oil leaking.
I don't know what to do at this point. I now have all the tools I need to tap the block, but am wondering if there's a better way to go about this. There's wayyy too much conflicting information - both here and online.
Bluevitz-rsOshawa, Ontario, Canada · Nov 18, 2010#17Here's a picture of the Greddy pan...
Picture not included in this copy
Focus_Sh1ftNew Jersey · Nov 18, 2010#18^ Thanks for the pic. That design is nearly identical to Zage's... With the exception of the return line routing.
EDIT: I just had an interesting thought. Say there was a pressure buildup at the turbo. Is it possible this could cause an increase in pressure at the feed location (in my case, the oil filter)? I've been noticing slightly higher oil pressures recently (90+, esp. at idle). Could be normal / unrelated though.
Bluevitz-rsOshawa, Ontario, Canada · Nov 18, 2010#19depends on RPM. When cold (under 10°C) oil pressure is around 80-90 psi @ 1500RPM and above until it starts to warm up. My car is usually at about 68 psi at cruse (2500ish RPM)
^ if that's any reference to you.
Focus_Sh1ftNew Jersey · Nov 18, 2010#20Yeah that sounds about right for me as well.
I ask because I've had this bizarre leak from every filter I've used since I did the turbo install.
The mystery continues...
Nexus1155Dorchester · Nov 19, 2010#21Hypocrisy, thy name is.... you 😈
Focus_Sh1ftNew Jersey · Nov 19, 2010#22Nexus, good to hear from you again 👍
I just checked my BOV and there was so little oil. Again, no loss of oil on the dipstick. Apparently some oil is normal, and the amount I'm seeing is very little. I'm going to play with my return line and return gasket before making any decisions to tap the block. I've also never once seen smoke out my exhaust...
I did also yank the PCV hose off the MAF piping and threw a breather filter in. Probably better to be getting only clean air in the intake anyways. Screw the environment 😈
Nexus1155Dorchester · Nov 19, 2010#23hah yeah I lurk here alot, and stay in the background most of the time after the whole sleey0 thing. I like watching your builds progress.
I dunno, IMO whenever you turbo a car that isn't turboed to begin with from the factory, theres always going to be small BSey problems. Not something that will blow up the engine, but small things to irk you.
You guys have the oil drains going legit down into the oil pan. Mine are shaped like an L and have a small incline and then goes into the pan but it is on the line right above the pan. If mine doesnt have problems even with an incline in my oil returns which is technically a no no, then you shouldnt either.
Bluevitz-rsOshawa, Ontario, Canada · Nov 20, 2010#24I just had another idea as to the case of the backup on the return.
Everyone is thinking the return is too restrictive. Well has anyone considered there's a restriction in the PCV valve? If you had a build up of pressure in the crankcase, if the pressure isn't getting out the PCV valve there's only one other option, the drain line for the turbo.
PETERPOOPThread starterOahu · Nov 20, 2010#25Progress so far...
Got the pan back on. Decided to go below the oil line. Installed the turbo manifold, turbo, and downpipe. The oil send/return line, and now working on the water line.
Tightened the bango fitting with this ghetto trick.
Picture not included in this copy
Got the manifold and turbo in place without removing the A/C line. We bolted the turbo to the manifold behind the engine, and then lifted it up and bolted it to the block. We didn't bolt it together first and then try and wedge it into place. It was easier to bolt it together while behind the engine.
Picture not included in this copy
Picture not included in this copy
Quick question. Getting ready to put on the water line to the turbo. I am going to get it from the throttle body coolant lines. Just wondering if it matters which direction it flows into the turbo? Not sure which is "in" and which is "out." Even with the throttle body lines, which is "in" and which is "out." Obviously I can't start up the car to see which way it flows from the engine. If anyone knows, thanks in advance.
Focus_Sh1ftNew Jersey · Nov 21, 2010#26 Originally Posted by
Bluevitz-rs ↑ I just had another idea as to the case of the backup on the return.
Everyone is thinking the return is too restrictive. Well has anyone considered there's a restriction in the PCV valve? If you had a build up of pressure in the crankcase, if the pressure isn't getting out the PCV valve there's only one other option, the drain line for the turbo.
This was actually my first idea as to leaking oil. I undoubtedly had a kink in my PCV line, so I ended up pulling it and putting a breather on like two days ago. Carlos was telling me it wasn't possible though, so I dunno. I'll be watching my intake carefully... My ongoing code, P0101, hasn't returned after clearing it when I put that breather on as well.
PETERPOOP, the coolant flow direction doesn't matter. Great progress so far keep it up 😁
TamagoOff Grid · Nov 21, 2010#27 Originally Posted by
PETERPOOP ↑ Quick question. Getting ready to put on the water line to the turbo. I am going to get it from the throttle body coolant lines. Just wondering if it matters which direction it flows into the turbo? Not sure which is "in" and which is "out." Even with the throttle body lines, which is "in" and which is "out." Obviously I can't start up the car to see which way it flows from the engine. If anyone knows, thanks in advance.
the cool water (inlet) should be on the lowest fitting of the turbo.
Nexus1155Dorchester · Nov 21, 2010#28Crush washers are said to only need 12 ftlbs of torque to seal, usually i see them require about 85ft lbs torque to never leak. You might be better off shaving the sides of a wrench, or making a crow foot deal by welding a closed end side of the wrench onto a socket so you can get a wrench in there in some way.
Focus_Sh1ftNew Jersey · Nov 21, 2010#29 Originally Posted by
Nexus1155 ↑ Crush washers are said to only need 12 ftlbs of torque to seal, usually i see them require about 85ft lbs torque to never leak. You might be better off shaving the sides of a wrench, or making a crow foot deal by welding a closed end side of the wrench onto a socket so you can get a wrench in there in some way.
I definitely agree - they need way more torque than advertised. Without taking the turbo apart I got them pretty tight but they still leaked. It's easy to take apart too - the only thing holding it together is that c-ring thing I think it's called.
There wasn't room to fit a 17mm socket on it, right? I can't remember, but I do remember not using a socket...
Nexus1155Dorchester · Nov 21, 2010#30I'd take pics of the tools I made, but you shave down the edges of a wrench to fit it in there easier.
The crow foot is if you cut a box wrench in half and use the closed side and weld a socket on there so you can turn it with a ratcheting wrench. I don't know how to explain this better than that.
rob323Joyner, Brisbane · Nov 21, 2010#31 Originally Posted by
Bluevitz-rs ↑ I just had another idea as to the case of the backup on the return.
Everyone is thinking the return is too restrictive. Well has anyone considered there's a restriction in the PCV valve? If you had a build up of pressure in the crankcase, if the pressure isn't getting out the PCV valve there's only one other option, the drain line for the turbo.
Or as the cars get older, the dip sticks pop out. 😁
This would be why most factory turbo cars have two breathers on the rocker cover, one with the pcv to the plenum, the other back to the intake before the turbo.
PETERPOOPThread starterOahu · Nov 25, 2010#32Done.
Picture not included in this copy
More pics to come after Turkey dinner.
Holy shit!
Focus_Sh1ftNew Jersey · Nov 25, 2010#34Looks great.
How'd you mount the intercooler?
PETERPOOPThread starterOahu · Nov 25, 2010#35For the AEM meth injection squirter/nozzle, a hole was needed to be drilled to fit it. We slightly bent the pipe so the nozzle could squirt towards the throttle body.
Picture not included in this copy
Picture not included in this copy
Oil catch can installed..
Picture not included in this copy
For the intercooler, it was mounted with some brackets we made for the bottom. Some plumber's tape was used for the top. It was kinda hard to make the intercooler centered, but we got it as close as we could.
Picture not included in this copy
Picture not included in this copy
Top shot..
Picture not included in this copy
TamagoOff Grid · Nov 25, 2010#36much better looking piping than the Greddy kit for the xA/xB
Bluevitz-rsOshawa, Ontario, Canada · Nov 26, 2010#37^ for sure!!!
Looks awesome. I still can't figure out why the intercooler has an offset outlet? It looks weird.
PETERPOOPThread starterOahu · Nov 27, 2010#38Thanks guys. This a very short clip of the turbo flutter that happens when shifting. Taken with a junk camera. Expect MUCH MUCH better quality videos once I am tuned.
I am running 14.5 (lean) during WOT, so I haven't been driving the car around that much. It also drives at 15.0 during normal driving conditions (a little lean), and idles from lean to rich. Definitely needs a new tune right. Waiting for the AEM tru boost controller to show up before the tune happens. Mind you, this is running with my supercharger tune that I still currently have. Not sure what kind of AFR numbers you'll get, pretuned, if you didn't have management from the start.
http://www.youtube.com/watch?v=BWiamyiPFhQ Nexus1155Dorchester · Nov 27, 2010#39Anything outside of boost, 13.5-16.0 is acceptable, mostly it tries to stay stoich at 14.7.
You are also running a non recirculated BOV it seems, you can see the AFR gauge go rich when the BOV pshhhts.
Boost you should be at 11-12.
Hope you get someone to tune it good for you!
PETERPOOPThread starterOahu · Nov 27, 2010#40Just pulled out the old spark plugs, look kind of worn, and the gap is at about 1.2 ( that was with the S/C ). Planning on putting on new ones (NGK Iridiums), any suggestions on a good starting point for the gap?
I'm also running meth injection under boost, will that also affect the gap?
I'm going to have the tuner gap them during the tuning session, but I don't know when I'll be able to get the car tuned. But for now, I am going to put some new ones in.
PETERPOOPThread starterOahu · Nov 27, 2010#41The 1.2 is mm, breaks down to like .045 (which is basically stock). But under boost, i was reading requires a smaller gap. Cali yaris is running .028 at IDK how many psi. I was thinking to set the gap at about .035 or something.
Any thoughts?
cali yarisCanoga Park, CA · Nov 27, 2010#42.028 gap at 14 psi up.
At what boost level is your meth injecting? I tuned my car up to 14 psi before it needed the meth.
PETERPOOPThread starterOahu · Nov 27, 2010#43Put in the new spark plugs, set the gap at .035. It actually gave me better AFR. It is now running at about 10-11 AFR during WOT, and 14.7-8 during normal driving.
Here's a new short little clip of doing WOT. Click HD and full screen to see the wideband numbers better..
http://www.youtube.com/watch?v=8kXZRORS9rk Right now I think I have the meth starting at 2psi. But when I get tuned, I am going to talk to the tuner to see when I should have it start.
Also, my current boost gauge is showing about 4.5 lbs of boost. Not too sure how accurate the gauge is. I thought the zage kit comes at 6-7lbs of boost? Going to be putting in a AEM tru boost digital boost controller in the near future. I'm going to set it at 8 lbs of boost.
cali yarisCanoga Park, CA · Nov 27, 2010#44Nice!!
I have my meth start at about 6psi. I don't think you need it before that point.
The zage kit comes with 0.5 bar spring which is just a bit over 7psi.
Nexus1155Dorchester · Nov 27, 2010#45.26-.30 gap i guess for when you boost. I guess .35 is ok. Watch for misfires, im surprised you didn't hear it breaking up before when it boosts like little pops everywhere.
Focus_Sh1ftNew Jersey · Nov 27, 2010#46 Also, my current boost gauge is showing about 4.5 lbs of boost. Not too sure how accurate the gauge is. I thought the zage kit comes at 6-7lbs of boost? Going to be putting in a AEM tru boost digital boost controller in the near future. I'm going to set it at 8 lbs of boost.
I had this problem. It disappeared as soon as I put a manual boost controller in though. Now I'm seeing 8ish during normal driving. The wastegate probably cracks around 5 psi and makes it hard to spool up fully.
How's your BOV situation? I watched the second video and can't really hear it. Kinda glad to see you're having fluttering as well... So far I've fully adjusted and loosened the BOV and it still always flutters.
PETERPOOPThread starterOahu · Nov 27, 2010#47Slow drive by..
http://www.youtube.com/watch?v=ZG5K3LgsJGw Re gapped to .030
FocusShift: Good to hear about the boost situation. All I hear is the flutter from the turbo. Can't really hear the BOV. You should post a video of yours......
Focus_Sh1ftNew Jersey · Nov 28, 2010#48 Originally Posted by
PETERPOOP ↑ Slow drive by..
http://www.youtube.com/watch?v=ZG5K3LgsJGw Re gapped to .030
FocusShift: Good to hear about the boost situation. All I hear is the flutter from the turbo. Can't really hear the BOV. You should post a video of yours......
Hm, on closer inspection that BOV sound you have is nothing like mine. That's why I didn't really pick up on it at first. I'll try to get a video this week... Tbh I don't know how to capture the sound on an automatic though 🤷
PETERPOOPThread starterOahu · Dec 5, 2010#49Just installed the AEM Tru Boost controller. Putting down about 7.88 lbs of boost. Loving the power. Can't wait to get it retuned. Just waiting for my HKS SSQV 3 BOV to get here.
http://www.youtube.com/watch?v=wHxZFGqow0c TamagoOff Grid · Dec 5, 2010#50 Originally Posted by
PETERPOOP ↑ Just installed the AEM Tru Boost controller. Putting down about 7.88 lbs of boost. Loving the power. Can't wait to get it retuned. Just waiting for my HKS SSQV 3 BOV to get here.
http://www.youtube.com/watch?v=wHxZFGqow0c
sounds good, but why spend money on the SSQV?