sleey0Original postPA · Oct 4, 2010#1As requested all answers and issues will be discussed here.
Met a guy that has a shop, access to dyno, can pull engine and do pistons and rods, and is willing to do it all! Works out great as he is near me:) Forget the 85$/hr stuff 90 miles away.
Cliff, buddy, you are my savior!
So here goes:
1ZZ or Tc injectors
Denso Ik22's (already bought new for $25. Gotta LOVE amazon lol)
Zage kit minus oil pan and IC (mushimoto -
anyone know which will fit I have a link.)
AEM FIC
AEK METH KIT
Crower Rods and pistons (xbg - please contact me ASAP)
All guages necessary like boost, wideband, etc
Can we use the gloshift oil filter sandwhich adapter for feed only or can it be used for oil pressure reading?
We are also going to drill my block for return. Stock oil pan to the rescue!!!
My buddy has an idea for those pesky AC lines next to the ecu - use t-pipe or 90 deg elbow and either some stainless or AC rated rubber lines to move out the way. He said that would be cake.
Also, I MIGHT move the OEM ecu into the cabin by the glovebox or Heat shield it really good if left in the engine bay.
The dude can paint, has access to lifts, and will also tune the car with the Dyno either free or for darn cheap.
METH KIT- Going to most likely use the spare tire well and if u haven't already noticed there is a grommet in there that allows access to under the chassis.
So, Anything missing? Any thoughts?
This project will be ongoing and I might play with a Blitz sc first until the rest of my funds come in to do the turbo.
Also, would pistons/rods/sleeves be a good idea right off the bat or wait?
EDIT: Scrapped
Anything else?
Any info or bashing whatever. Just speak your mind here.
Love these boards and wish me luck!!!!! I will need it although Cliff has been working on cars, boosted or not, for years.
Oh, and he also welds and can get me a dowpipe-back exhaust made for cheap! Things just turned for the better today folks!!!!!!!
🤘
Replies 128
Focus_Sh1ftNew Jersey · Oct 4, 2010#2Didn't even read it yet but.
HALLELUJAH
🙇🙇
Now answer my question in the other thread.
Focus_Sh1ftNew Jersey · Oct 4, 2010#3 Can we use the gloshift oil filter sandwhich adapter for feed only or can it be used for oil pressure reading? Both. Do it.
We are also going to drill my block for return. Stock oil pan to the rescue!!! If I wasn't lazy I'd have done the same.
My buddy has an idea for those pesky AC lines next to the ecu - use t-pipe or 90 deg elbow and either some stainless or AC rated rubber lines to move out the way. He said that would be cake.
Uh, just disconnect them, install turbo, reconnect lines. Recharge and you're set?
Also, I MIGHT move the OEM ecu into the cabin by the glovebox or Heat shield it really good if left in the engine bay. Nah, ECU will be fine unless you're running a campfire under the hood. O2 wires are another story though.
The dude can paint, has access to lifts, and will also tune the car with the Dyno either free or for darn cheap. North NJ sucks.
METH KIT- Going to most likely use the spare tire well and if u haven't already noticed there is a grommet in there that allows access to under the chassis.
You sir, will be the guinnea pig for this. If all goes well I'll follow suite. DON'T BACK OUT. 👍
So, Anything missing? Any thoughts?
This project will be ongoing and I might play with a Blitz sc first until the rest of my funds come in to do the turbo. Ok.
Also, would pistons/rods/sleeves be able to hold up a twin charged engine around 13-15psi? Uhh....
I am thinking of a large fixed pulley on the blitz to make low boost for instant power (say 3psi max). Then let the blower take over after 2k RPM's. Just a thought as no one has done it, and prolly for good reason. Interesting, immediate low end increase. Methinks it's money wasted though if you have a quick spooling turbo.
Or is there more I will need to do?
Any info or bashing whatever. Just speak your mind here. Ok.
Love these boards and wish me luck!!!!! I will need it although Cliff has been working on cars, boosted or not, for years. Luck to you.
Oh, and he also welds and can get me a dowpipe-back exhaust made for cheap! Delicious.
Things just turned for the better today folks!!!!!!! Yay.
.
KCALB SIRAYVirginia · Oct 4, 2010#4If you need a Blitz, I have mine for sale dirt cheap!! Check the link below
sleey0Thread starterPA · Oct 4, 2010#5Thanks focus!
I knew you were just in my same sit not too long ago so you can relate to what I am going thru right now.
RE; twin charge. I MAY be able to get a dirt cheap blower and was just going to do it for show competitions, mainly.
Plus, since the Zage is dirt cheap, like garm said it gives you more $$ to spend eslewhere. lol
Thank you, focus. My name is Wes, BTW.
I like to be more personal. I don't call garm cali_yaris and RARELy call Aras xbg (well, it's shorter so meh??)
Thank you all for inspiring me to do this project!!!
Still need to know what amount of $$ I am looking at for pistons and rods. Hopefully Aras will let me know:)
Nexus1155Dorchester · Oct 4, 2010#6Everyone wants to do something crazy and something that no one has done yet, like XBGod. Its part of being human. I wanted to do K16 turbos on my S4, I got it done, made 10psi, didn't have time to fix the issues so I did something tried and true. I didn't know why I tried that, the car is ridiculously fast now on bolt on turbos.
Do the turbo first, enjoy it for a while and see how you like it. With a small engine like this on a GT25 turbo it will be zippy enough that a supercharger won't really make a lick of difference.
If you are going to do pistons and rods you should be able to push enough power to make anyone happy.
Try to find a cheap beater in the mean time to drive. Atleast some $400 junk box on craigslist.
sleey0Thread starterPA · Oct 4, 2010#7 Originally Posted by
Focus_Sh1ft ↑ Didn't even read it yet but.
HALLELUJAH
🙇🙇
Now answer my question in the other thread.
What question in what thread lol.
Confused....
cali yarisCanoga Park, CA · Oct 4, 2010#8Meth kit should be closer to the motor. DO NOT run it outside. In stock btw.
No need to move the ECU.
Add a vented hood and an exhaust system to your list.
I will have oil sandwich adaptors in stock next week.
twin charging a Yaris is smart to make history and dumb to make power.
at 13 psi, you will need a fuel pump, larger injectors and possibly a return line. I know the stock pump gives up right about there.
sleey0Thread starterPA · Oct 4, 2010#9Well where in the ln the engine bay does.a gallon tank fit? Engine bay is the size of a cerial box!
And no i am not using the windshield washer tank.
Please enligbten me garm lol.
cali yarisCanoga Park, CA · Oct 4, 2010#10Mine is behind the passenger seat. Check where Echo put his in the MI thread.
You want big power? -- you just might have to give up something.
Just don't run the line under the chassis, please.
sleey0Thread starterPA · Oct 4, 2010#11Behind the seat isn't much longer in the spare tire bay in the hatch. ??
And, ok I will not run them under the chasis.
Thx
Nexus1155Dorchester · Oct 4, 2010#12JDM STI Meth Tank. Get something like this and bolt it to the back of your rear seats. You'll be good to go.
Picture not included in this copy
xbgodFlorida · Oct 5, 2010#13Slow down Turbo.....one power adder only.
You would need to run two different fuel maps to run both and have someone with serious knowledge in tunning. I already thought about what your talking about and was going to do it years ago. It's just not worth the effort. You are going to run a small turbo anyways, so spool up time will be quick.
If you try and do all that stuff you will no longer have a daily driver. You will face challanges that most tunners can't even handle.
If you do trunk mount the meth kit you will need a electric silonoid like from a nitrous kit to feed the pump. Typically your resivor should be higher than your pump to gravity feed.
Snow Performance actually makes a much nicer kit than AEM. Call and talk to Karen over there she knows me personally. Tell her the XB guy sent you. or just ask for Matt Snow. They offer a much more extensive kit with electronics. Their kit is a little more but may be worth your situation.
I use AEM now because it's just more race oriented and Greg Nakono gave it to me.
Good building
XBG
sleey0Thread starterPA · Oct 5, 2010#14Awesome stff guys!
The meth kit I will leave for after the project. But the dude helping recommend it.
sleey0Thread starterPA · Oct 5, 2010#15Another update zage said kit without pan and intercooler is$ 1510
Not too bad but what about shipping? Lol
sleey0Thread starterPA · Oct 5, 2010#16Thanks for all the meth kit pics!! Really helps:)
Does AYNYONE know either the size of the zage IC or if that Mishimoto IC will fit.
Dimensions for the Mish are 28" x 7.5" x 2.5", Core Size: 20.5" x 6.25" x 2.25" <<--- Outer dim seem pretty small and specs on it are good for my app oh and plus it's inexpennive).
Anyone?
Later,
Wes
Nexus1155Dorchester · Oct 5, 2010#17He's trollin!!! 😛
Yes, the glowshift adapter has a port for an oil pressure gauge as well as oil feed, etc.
sleey0Thread starterPA · Oct 5, 2010#18Was in my amazon cart for that long lol.
Told you I have been planning for months.
BUT just cancelled due to user interfence! lol
sleey0Thread starterPA · Oct 5, 2010#19Is this the right Meth kit? Bottle MAY fit in the bay somewhere.
How would methanol clean windshields? Get bugs off? Streak-free? lol
1 attachment not included in this copy
cali yarisCanoga Park, CA · Oct 5, 2010#20^ that's what I have in my car, works 100% and fairly simple. Echo has it in his car too, and Morgan used it on her Frankenstein supercharger install.
Focus_Sh1ftNew Jersey · Oct 5, 2010#21 Originally Posted by
sleey0 ↑ Is this the right Meth kit? Bottle MAY fit in the bay somewhere.
How would methanol clean windshields? Get bugs off? Streak-free? lol
I remember reading somewhere that typical wiper fluid has anywhere from a 30-60% methanol mix. However, wiper fluid usually has cleaning agents that, well, clean lol. You don't want that in your methanol mix though.
I feel like it wouldn't be too hard to find a spot for the tank. If you can't fit it in the engine bay, there should be enough room behind the passenger glove compartment.
cali yarisCanoga Park, CA · Oct 5, 2010#22if you are using water/meth, it's gotta be distilled water too
sleey0Thread starterPA · Oct 5, 2010#23Thanks for the tips fellas!
xbgodFlorida · Oct 5, 2010#24Use VP M1 Methanol with distilled water.
5 gallons of M1 Meth makes 10 gallons. Always mix 50/50
XBG
sleey0Thread starterPA · Oct 5, 2010#25Thanks, Aras.
Just looking for a Tach now.
Any1 with suggestions?
Nexus1155Dorchester · Oct 5, 2010#26Now im getting confused, i thought you already ordered them?
am i still the only person thats sees whats going on🤷 Come on i know deep down some of you know it too.😈 Attack me if ya want but you know...
sleey0Thread starterPA · Oct 5, 2010#28I had.that order cancelled after speaking with garm.
Id rather support a great sponsor like MI.
So if anyone has any reasonably-priced gauge recommendations let me know!
I didnt know garm sold gauges.
And wtf r u talking about yoda?
Please either help out or dont comment. Not to be rude but i want to try and keep this thread clean.
Thanks!
Focus_Sh1ftNew Jersey · Oct 5, 2010#29 Originally Posted by
Yoda ↑ am i still the only person thats sees whats going on🤷 Come on i know deep down some of you know it too.😈 Attack me if ya want but you know...
I seriously hope not, but it's at the back of my mind too.
Sleey0, just use sunpro gauges. A gauge is a gauge is a gauge. Unless it's a $250 boost gauge with a turbo timer and controller, but you get my point. Sunpro gauges are dirt cheap. They don't look bad either if you want white face gauges.
I got a water temp, boost, voltmeter, and oil pressure gauge for $50 shipped lol.
sleey0Thread starterPA · Oct 5, 2010#30No, a gauge is not JUST a guage.
If you buy crap (Sunpro isn't too bad but I will spend extra on my gauges) and the readings are wrong then bye-bye engine. The gauges are what you trust to be right.
Would you use Gloshift gauges? Heck, fracking, no!
I cannot really believe you said that lol.
I hope xbg doesn't jump on you for that one!
sleey0Thread starterPA · Oct 5, 2010#31Ok. Pistons.
Here are the CP pistons for the 1NZFE
http://www.atomicspeedware.com/1NZFECP.aspx What bore size am I looking for? There are 2 models - 75mm and 75.5mm. Is the 75mm standard?
What are the advantages to oversized pistons? Focus_Sh1ftNew Jersey · Oct 5, 2010#32 Originally Posted by
sleey0 ↑ No, a gauge is not JUST a guage.
If you buy crap (Sunpro isn't too bad but I will spend extra on my gauges) and the readings are wrong then bye-bye engine. The gauges are what you trust to be right.
Would you use Gloshift gauges? Heck, fracking, no!
I cannot really believe you said that lol.
I hope xbg doesn't jump on you for that one!
What 🤷
They work for me 😁
I thought the whole working part was common sense lol. If I buy an oil pressure gauge, hook it up, and see 400 psi on a gauge that only reads up to 100 psi, then clearly I need a better gauge.
cali yarisCanoga Park, CA · Oct 5, 2010#33oversized piston = more displacement = more power.
But it also means the block has to be bored and possibly sleeved. WAY more money than stock sized pistons.
A gauge is a gauge is a gauge.
That is just so incorrect; I'm not even going to start on it.
Put a Glowshift gauge next to an Autometer gauge, for example.
My oil pressure gauge saved my tC's life when the oil cooler popped a hose. I will never cheap out on gauges.
Nexus1155Dorchester · Oct 5, 2010#34 If you buy crap (Sunpro isn't too bad but I will spend extra on my gauges) and the readings are wrong then bye-bye engine. The gauges are what you trust to be right.
You're starting to sound like XBGod, not a bad thing IMO, but sometimes the best of the best is overated. You don't always need the cream of the crop.
If thats what you are going for get some DEFI gauges.
A Mechanical gauge is a mechanical gauge. They all operate the same way. Personally I am a fan of VDO. I have used their boost gauges many of times.
Focus_Sh1ftNew Jersey · Oct 5, 2010#35 Originally Posted by
Nexus1155 ↑ You're starting to sound like XBGod, not a bad thing IMO, but sometimes the best of the best is overated. You don't always need the cream of the crop.
If thats what you are going for get some DEFI gauges.
A Mechanical gauge is a mechanical gauge. They all operate the same way. Personally I am a fan of VDO. I have used their boost gauges many of times.
Ok, better put than what I said. For example:
Sunpro oil pressure gauge - no more than $20
AEM oil pressure gauge - $200
They do the SAME THING, except one is mechanical and one is electric. An insignificant difference if they both work.
Cut me some slack guys, I had to save money somewhere on this install - it isn't exactly cheap lol.
Nexus1155Dorchester · Oct 5, 2010#36Honestly I would rather mechanical gauges vs. electrical gauges anyday of the week.
sleey0Thread starterPA · Oct 5, 2010#37 Originally Posted by
cali yaris ↑ oversized piston = more displacement = more power.
Thank you, Garm.
Originally Posted by
Nexus1155 ↑ You're starting to sound like XBGod, not a bad thing IMO, but sometimes the best of the best is overated. You don't always need the cream of the crop.
If thats what you are going for get some DEFI gauges.
A Mechanical gauge is a mechanical gauge. They all operate the same way. Personally I am a fan of VDO. I have used their boost gauges many of times.
No, xbg has much more money than me. Autometer gauges, not the high end ones, are reasonably priced. So Sunpro - $30, Autometer - $60 = worth it, IMO.
sleey0Thread starterPA · Oct 5, 2010#38Ok. Boodt/vac and oil pressure tachs figured out.
Any suggestions on a Tach??
cali yarisCanoga Park, CA · Oct 5, 2010#39focus, no one is criticizing you for your build, but I will disagree that "a gauge is a gauge".
Regarding mechanical gauges, I'm not running fuel or oil into my cabin to make a gauge work, so I will stick with my sensors and electric gauges.
sleey0Thread starterPA · Oct 5, 2010#40So, now that garrm let me in on that mechanical guage secret, I might go ALL-OUT and go PLX.
Will update soon.
By the time I buy all electrical guages I can get a nice PLX system.
Any1 familiar with PLX and ther sensor module hookuo?
sleey0Thread starterPA · Oct 5, 2010#41That is why we replace the rods and pistons if you are serious about power and your project.
Good aftermarket pistons/rods can with stand much more stress.
sleey0Thread starterPA · Oct 5, 2010#42I know as I am not a big fan on meth.
I'd rather pony up for CP pistons and Crower rods:)
Focus_Sh1ftNew Jersey · Oct 5, 2010#43 Originally Posted by
cali yaris ↑ focus, no one is criticizing you for your build, but I will disagree that "a gauge is a gauge".
Yeah I'm not offended or anything. We're all welcome to our opinions, I'm mature enough to deal with people disagreeing with me lol.
Originally Posted by cdydjded ↑
IMO a meth kit on our engine with stock rods & pistons is not nessesary. It will add more power & put stress on the stock rods & pistons that they cannot handle.
This was a pretty big fear of mine, and one of the reasons why I didn't immediately spring for meth injection. That's just pure speculation at this point though, isn't it?
I could have sworn Morgan or someone ran an SC with meth injection... Can't find info on that now. Anyone know how that went?
sleey0Thread starterPA · Oct 5, 2010#44Yeah, but do we KNOW what it does to out engines in terms of damage?
Might be something there.
Besides, pistons/rods is the way to go if you are worried about blowing an engine.
pimp my yarischicago · Oct 6, 2010#45Has anyone poped a stock motor yet???? If so, what kind of boost/horsepower were U making???? I plan on buying a junk yard motor next year and packing it with better internals, but I'm just curious how far the stock motor can be taken. Any one Bueller, Bueller?
sleey0Thread starterPA · Oct 6, 2010#46Not too.far.
Somehow garm got 378hp.
Wicked if u ask me lol.
cali yarisCanoga Park, CA · Oct 6, 2010#47 I could have sworn Morgan or someone ran an SC with meth injection... Can't find info on that now. Anyone know how that went?
She did, and it cured detonation problems. Meth injection
can be used for more mild purposes, guys, not just big power.
cali yarisCanoga Park, CA · Oct 6, 2010#48 Garm drove around for 8 months @ 180hp. Thats 90 more whp than stock. IMO thats about as high as you want to go.
Lost just a bit of compression in one cylinder over that time, too. Of course, that was only roughly tuned, so I can't point at a single exact cause.
to answer pimp's question. I don't know anyone who has blown up a 1.5L motor -- although I think Tamago threw a rod, as I recall.
sleey0Thread starterPA · Oct 6, 2010#49Ok.
T c injectors or 1zz and why?
PETERPOOPOahu · Oct 6, 2010#50 Originally Posted by
cali yaris ↑ ^ that's what I have in my car, works 100% and fairly simple. Echo has it in his car too, and Morgan used it on her Frankenstein supercharger install.
Originally Posted by
Focus_Sh1ft ↑ I could have sworn Morgan or someone ran an SC with meth injection... Can't find info on that now. Anyone know how that went?
Originally Posted by
cali yaris ↑ She did, and it cured detonation problems. Meth injection can be used for more mild purposes, guys, not just big power.
Easily forgotten... lol
I run meth with a S/C, and I am the only S/C'd yaris that is re-tuned with meth ( let alone re-tuned). I'm running straight meth, no 50/50 mix.