Yarisworld Archive

Sleey0's Turbo Projec!

129 posts · 27,912 views · page 2 of 3

Replies continued

xbgodFlorida · Oct 6, 2010#51
I've blown one of these motors😆

Was using the Blitz S/C and Nitrous. Forgot to purge the nitrous bottle pressure down before launch and BOOMMMMMM!

Bottle pressure was at 1600 from sitting in the heat needed to be at 1000, but that my own fault. snaped 3 rods and turned the piston 90 deg. in the block. I have the rods and pistons at home as a reminder of what not to do.

You my friend need to just start your build. For someone on a budget your looking at parts that go way beyond your means.

As far as PLX goes I use their AFR gauge it's deadly accurate.

As far as meth goes great way to keep you from detonating and run smoother. You can get an octane rating up to 101 with meth and 93 pump gas. Thats what I've been using. Best bang for the buck. I've switched to a race fuel for this new build but I don't drive this as a DD.

My ride with all that high end fancy shit has put me in the 60,000 price range on my build. But I;ve had the money to play with.

XBG
cali yarisCanoga Park, CA · Oct 6, 2010#52
You can get an octane rating up to 101 with meth and 93 pump gas. Thats what I've been using.
I think more. I can run up to 30+ psi with 50/50 water meth. You can't be saying I'm doing that with equivalent 101 octane.
cali yarisCanoga Park, CA · Oct 6, 2010#53
T c injectors or 1zz and why?
I don't think you've said definitively how much boost you are going to run. You may not know yet. Boost level will determine fuel needs which will determine injector choice, need for a pump and possibly return line, etc.

It depends!
sleey0Thread starterPA · Oct 6, 2010#54
You guys are going to start loosing teeth and get "meth-mouth" with all this "pure" meth talk.:(

lol HAD to do it...

Anyway, does anyone here have anything to say about CP pistons? Good/reliable? Not so good? Good but overpriced>

TIA
Focus_Sh1ftNew Jersey · Oct 6, 2010#55
Easily forgotten... lol

I run meth with a S/C, and I am the only S/C'd yaris that is re-tuned with meth ( let alone re-tuned). I'm running straight meth, no 50/50 mix.
Used for power or to stave off detonation? Gimme numbers pleeeeease 😁

How long have you been running the SC and meth?
sleey0Thread starterPA · Oct 6, 2010#56
Originally Posted by pimp my yaris ↑
Has anyone poped a stock motor yet???? If so, what kind of boost/horsepower were U making???? I plan on buying a junk yard motor next year and packing it with better internals, but I'm just curious how far the stock motor can be taken. Any one Bueller, Bueller?
Found a 40k mile used engine for $350.

Says it has been tested and runs.

That's whats nice about the 1NZFE - cheap crate or used motors FTW!!
cali yarisCanoga Park, CA · Oct 6, 2010#57
I have used CP pistons in all three of my turbo project cars. No complaints, they hold up really well. Been running my tC at 400+ whp as a daily driver for well over two years on those pistons.
sleey0Thread starterPA · Oct 6, 2010#58
Thanks garm.

I know.arias.will custom make.them but id.rather just buy everything together lol.
xbgodFlorida · Oct 6, 2010#59
You still need to find the info on my dome...........

The even bigger secret will be in my head work, the brains of my motor.

Not to mention figure out how to use 70mm T/B with a custom one off sheet metal intake.

Lots of tricks still up my sleve can't givem all away.

XBG
cali yarisCanoga Park, CA · Oct 6, 2010#60
^ LOL.

Celica GT-S is 70mm, easy to source and works great in my car. 😁
sleey0Thread starterPA · Oct 6, 2010#61
Ok so 2 guages have been ordered (below). Waiting on garm for FIC and UEGO and BOV (Greddy, maybe?).

Which BOV makes the best sound? lol I WANT DARTH VADER HOOPER SOUND!!!!!

Auto Meter AM-7153 C2 Series 2-1/16" Oil Pressure 0-100 PSI
Auto Meter AM-7159 C2 Series 2-1/16" Boost-Vac 30 IN HG/30 PSI

The white face UEGO should match nicely with the C2 auto meters:D
sleey0Thread starterPA · Oct 6, 2010#62
Can anyone post pics of where they put there tachs? not in the a pillar but mounted on steering column or dash?

THANKS!
xbgodFlorida · Oct 6, 2010#63
Thats good info Garm....But it's not a Edlebrock Victor-x Racing series 70mm T/B on a sheet metal intake with direct port nitrous.🤘



XBG
sleey0Thread starterPA · Oct 6, 2010#64
Any1 use RFL BOV's?

I heard they are Real Fucking Loud lol:D
xbgodFlorida · Oct 6, 2010#65
The C2's are nice, thats whats in my car. And I just got the new digital C2 Wideband AFR gauge from my buddy over at Autometer, so my PLX one is coming out for asthetic purposes. You will like the C2's Full sweep electric the only way to go.

XBG
xbgodFlorida · Oct 6, 2010#66
Bling...............

3 attachments not included in this copy

cali yarisCanoga Park, CA · Oct 6, 2010#67
You'll have to get the Autometer rheostat kit (or similar from somewhere else) to go with those C2's -- they are WAY too bright at night.
sleey0Thread starterPA · Oct 6, 2010#68
Originally Posted by cali yaris ↑
You'll have to get the Autometer rheostat kit (or similar from somewhere else) to go with those C2's -- they are WAY too bright at night.
What do you mean? The kit turns down the brightness?
sleey0Thread starterPA · Oct 6, 2010#69
http://www.zageturbo.com/pro/proshow.asp?y42j0cl=138

Doesn't look too bad. If you notice there are 10 bolts for the oil pan hahahaha (inside joke)

Love ya and u know who I am talking about:D

Still don't know why the IC inlet and outlet are not even. Any guesses?
cali yarisCanoga Park, CA · Oct 6, 2010#70
What do you mean? The kit turns down the brightness?
Yes.
sleey0Thread starterPA · Oct 6, 2010#71
So, I got the C2 boost gauge. Garm introduced me to controllers.

Is it ok to use the c2 and mechanical controller like Hallman?

Or would it be best to get the AEM digital gauge controller? If I go with the Tru-Boost it will be the same money wise as C2 and Hallman.

Whaddya think? I think that hallman looks kick ass and it is pretty inexpensive:D
sleey0Thread starterPA · Oct 6, 2010#72
Oh and just talked with my buddy doing the install. First he laughed at my engine and said him and a few buddies coiuld lift it out.

Anyway, He says it will take about 1 hour to get the engine out and about 2-3 hours to install pistons/rods and anothe hour to put it back

BUT we will most likely fire it up first to make sure the pistons and rods are ok an there are no leaks anywhere etc.

Then the Zage. He took a look at pics and said maybe a full day, most liekly less. He said the kit looks like good quality. So +1 for Zage!

Wiring the AEM will be the most challenging part, believe it or not. lol Although I have good documentation from you guys here and MI that already did it.

Then we shall do gauges and take it for a spin. If it is driveable than to the dyno it goes (the dyno is like 45min away). If not than the dude has a trailer to bring it there.

A week/week and a half sound about right.

Also he has access to a press so if you guys want AC lines moved professionally maybe he can make some extra off my copy.

Basically getting rid of current AC lines and making new ones that angle and fit without being near heated components.

~Wes
Nexus1155Dorchester · Oct 6, 2010#73
Where do you order from that lets you keep cancelling!

Remember, you are going to lose most fluids when doing an engine pull. You really should not have to pull the engine just to do a turbo kit, but if you do, remember to stock up on oil coolant power steering fluid and brake fluid.

You also might not want to pull engine depending on wall clearance, might make it harder to get back in.
sleey0Thread starterPA · Oct 6, 2010#74
Well, oif course I aint't pulling that small bastard to just pu the kit on.

I am getting CP 75mm pistons and Crower rods.
Nexus1155Dorchester · Oct 6, 2010#75
Still think it would be easier just to remove the head alone and not risk things/fluids too. Also make sure you get some head studs. You cannot reuse stock head studs, most of them now a days are all stretch bolts and thats a no no on reuseability. Same with flywheel bolts.
sleey0Thread starterPA · Oct 6, 2010#76
Where can I get 1NZFE head studs?
Nexus1155Dorchester · Oct 6, 2010#77
Garm got them custom, but Toyota has them for sure i bet at like $5 per stud. Also another way to lower your compression to push more boost is to get a thicker head gasket. I don't know how much your pistons will lower them, but the headgasket is good for another .5 of a drop
MorganPCB, FL · Oct 6, 2010#78
Originally Posted by Focus_Sh1ft ↑
Used for power or to stave off detonation? Gimme numbers pleeeeease 😁

How long have you been running the SC and meth?
Originally Posted by cali yaris ↑
She did, and it cured detonation problems. Meth injection can be used for more mild purposes, guys, not just big power.
I had a Blitz supercharger and the AEM progressive water/meth set up (the one you have pictured). Worked nicely. I mounted the tank to the back of the "40" seat (of the 60/40 rear bench) in the hatch. The regular washer take is 1.1 qts and you'll burn through that quickly enough. Run the lines through the car, they aren't under pressure until after they pass through the pump.

Since I live in Florida and I installed the kit in May of last year, it was hot, well over 95+ most summer days and the methanol kit was to help with pre-detonation. Yes, you can run 100% methanol or yes, you can run 100% water. I never noticed a huge difference, usually I ran tap water with about 30% by volume of methanol.

If you choose to run straight methanol, it can be very expensive for not a lot of return in power - just save yourself the money, the real power is not found (for this car) in adding water/methanol injection. But it is a lot safer to run in hot weather ESPECIALLY since I didn't have an intercooler.

Cooler intake temperatures are never a bad thing.

Good luck, read my archaic posts if you feel like you'd like to waste 20 mins on my ramblings.... or just PM me 🙂

ps I knew from the get go that I was going to have water/meth, so I installed it simultaneously with the supercharger... it is a very nice kit, well worth the $400 - just make sure you get refrigerator tubing for the lines from the tank to pump and pump to injector, the ones in the kit are very thin and will break if you run anything higher than a 30% mixture
PETERPOOPOahu · Oct 6, 2010#79
Originally Posted by Morgan ↑
If you choose to run straight methanol, it can be very expensive for not a lot of return in power - just save yourself the money, the real power is not found (for this car) in adding water/methanol injection. But it is a lot safer to run in hot weather ESPECIALLY since I didn't have an intercooler.
Not true. The meth actually lasts quite awhile. Depends on how you drive of course. Since I am maxing out at about 8-9lbs of boost, i have my meth kick in at 2lbs of boost. I also buy HEET to use as my meth, and it's only a couple bucks a bottle at WAL-MART. Takes about maybe 8-9 bottles to fill the entire meth kit? A full tank of meth can last me about a month with my driving. However, I don't street race and go into boost every chance I get....

ps: I wouldn't have even gotten the meth kit if i wasn't going to tune with it.

Picture not included in this copy

Originally Posted by Morgan ↑
make sure you get refrigerator tubing for the lines from the tank to pump and pump to injector, the ones in the kit are very thin and will break if you run anything higher than a 30% mixture
Not true. I am running 99.9999% meth and my stock hose lines haven't broke....
cali yarisCanoga Park, CA · Oct 7, 2010#80
make sure you get refrigerator tubing for the lines from the tank to pump and pump to injector, the ones in the kit are very thin and will break if you run anything higher than a 30% mixture
I run 50/50, and I will also disagree with this.

Where exactly did the 30% come from?
cali yarisCanoga Park, CA · Oct 7, 2010#81
He says it will take about 1 hour to get the engine out and about 2-3 hours to install pistons/rods and anothe hour to put it back
That would be the fastest swap I've ever seen. I will keep my healthy skepticism on this detail.
cali yarisCanoga Park, CA · Oct 7, 2010#82
I am getting CP 75mm pistons and Crower rods.
What compression? If not stock, I'm guessing you'll be in trouble with the ECU and a piggyback.
xbgodFlorida · Oct 7, 2010#83
Your engine builder is full of shit, will take a few hours to pull the motor correctly. And if your gonna do some piston changes that change compression and or CC you may have some trouble with that piggy back ECU.

Your engine builder is working in dream land and your in for a wake-up call on this whole thing.

My self and Garm got more time under the hood of these cars than your engine builder probably has in his whole career.

Your whole situation is unrealistic and there is a world of issues headed your way.

A few hours to put new pistons and rods in. 😆

Not if you have file fit rings and you want to check everything. Not to mention you need to knoch the block for the Crower rods to clear.

Also there is no ARP head stud kit for this car. You have to go custom like me and Garm. And untill you go big like him and I you don't even warrent them.

Good Luck with this disaster

XBG
advocatelocation · Oct 7, 2010#84
Originally Posted by Nexus1155 ↑
power steering fluid
don't we have electronic power steering?
cali yarisCanoga Park, CA · Oct 7, 2010#85
you need to knoch the block for the Crower rods to clear.
The Pauter rods were the same for me.
Nexus1155Dorchester · Oct 7, 2010#86
don't we have electronic power steering?
I dunno, never looked into it. Just saying what you'd need for general motor pulls
cali yarisCanoga Park, CA · Oct 7, 2010#87
Yaris = Electronic power assisted steering
Focus_Sh1ftNew Jersey · Oct 7, 2010#88
Kinda surprised no one has said this yet but uh...

How about you just put the turbo in and deal with pistons/rods/meth/everything else later. It's like you're trying to do brain surgery, file your taxes, build a time machine, and create a dog/cat fusion all at once. What's the rush?
advocatelocation · Oct 7, 2010#89
I'm guessing he doesn't want to disassemble the turbo once it's on in order to get the new pistons in and sleeve the block if he wants?
Focus_Sh1ftNew Jersey · Oct 7, 2010#90
Gonna be pretty hard to trouble shoot...

But that's probably exactly what the installers want to have happen. 🙄
xbgodFlorida · Oct 7, 2010#91
Brother I hope you do get your build the way you want. Your just taking to many avenues of approach for 7psi. Hell those rods are safe on 10psi. Your daily driver is no longer going to be that but you'll figure that out.

Almost forgot, I don't need you to stand-up for me. People just get pissed because I beat them to the next level, it's human nature. And I know where I stand in-line, in this food chain of the 1NZ-FE.

Belive me, when people do get the chance to see me at a show..I never get a hatter at me...My arms are the size of some peoples thighs and my neck gets lost in my traps. Just like I build powerful motors I treat my body the same.

I hope your on the war path to build this now....that's my goal...piss you off bad enough you might just get there...Reverse psycho-therapy is great.

Now build something

XBG
sleey0Thread starterPA · Oct 7, 2010#92
And some new info gained by a trusted member.

Pistons and rods may be a project down the road now depending on my funds standpoint here in the next month or two,

So no more bashing/talking/whatever about the rods/pistons and engine pull plz.
sleey0Thread starterPA · Oct 7, 2010#93
Back to my project.

Should I get the 1ZZ injectors? Or go bigger, like tC?

Performace/sftermarket ones?

Any suggestions......Thanks
MorganPCB, FL · Oct 7, 2010#94
Originally Posted by PETERPOOP ↑
Not true. The meth actually lasts quite awhile. Depends on how you drive of course. Since I am maxing out at about 8-9lbs of boost, i have my meth kick in at 2lbs of boost. I also buy HEET to use as my meth, and it's only a couple bucks a bottle at WAL-MART. Takes about maybe 8-9 bottles to fill the entire meth kit? A full tank of meth can last me about a month with my driving. However, I don't street race and go into boost every chance I get....

ps: I wouldn't have even gotten the meth kit if i wasn't going to tune with it.

Picture not included in this copy



Not true. I am running 99.9999% meth and my stock hose lines haven't broke....
I was going through the 1 gallon tank (the one pictured) every couple of days or roughly 100 miles. I started buying methanol in bulk from a local auto shop. If you factor in the $40 methanol storage 5 gal tank and then $5 per gallon, it wasn't "very" expensive, so I guess I take back my intensifier.

Oh yes and HEET is a great substitute if you can not find methanol in bulk quantities, also most washer fluids will list methanol content if you can do some calculation on what temperatures they work in. Roughly a -20* solution is 25-30% methanol, but living in a state where it rarely freezes.... the closest I ever found local to me was +20* washer mix
Originally Posted by cali yaris ↑
I run 50/50, and I will also disagree with this.


Where exactly did the 30% come from?
As to the lines breaking, I had to keep extra tubing in the car and a pair of scissors on me at all times... along with a hex head 6mm and a 14mm wrench. I never had a problem with any of the lines in the car, only the one from the pump outlet to the injector. After playing with where the line was routed and eliminating that as a possible cause for leaks, I assumed it was the tubing and after switching to a higher thickness tubing I never had any issues.

My 30% by volume (not weight) came from my own diagnostics. I'm not saying I'm a "genius" by any means but it ran quicker from 25 to 75 mph in 5th gear when the mix was between 2/3 to 3/4 water to 1/3 - 1/4 methanol. Of course if you live anywhere outside of my neighborhood (humidity, elevation... blah blah variables), this may not be helpful to you. However, I was sharing what worked for me... sorry for the intrusion....
PETERPOOPOahu · Oct 8, 2010#95
I would have went the windshield wiper fluid route for the meth, but because I am in hawaii, they don't sell the windshield washer fluid that could work.
sleey0Thread starterPA · Oct 9, 2010#96
Ok. Here we can talk about aftermarket pistons and rods and how our learning ECU will handle the lower C:R.

I am making some calls today an will report back what I find.

FEEL FREE TO DISCUSS.....

<And, thank you Garm and Aras>
sleey0Thread starterPA · Oct 9, 2010#97
...... reserverd
sleey0Thread starterPA · Oct 9, 2010#98
Just wondering if the ECU woulod re-learn the C:R if it was minimally changed , say like 10:1 iinstead of 10.5:1.

All I want to do is beef up my internals a bit to hit 12psi to 1bar reliably,

I called AEM, CP, and ARIA but all are closed on weekends and will have to wait for answers lol.

I should just yank my cars ECU and send it to CTScott to play with. He could get it in constant open-loop then none of this matters lol.

Thanks for listening,
Wes
xbgodFlorida · Oct 9, 2010#99
I see this threads been Hi-jacked.....it's missing posts now too.

Instead of worring about all this other nonsense, you could just play it safe, since this is your DAILY DRIVER and put a reliable kit on have some fun and then play with the big dogs when you can afford to not have it be a daily driver.

All your threads are running wild with no end results. Look no one cares anymore. you are the only one responding to your own threads.

I give up, I quite, I resigne.....I'm throwing in the towel.....I'm ringing the bell.


XBG
sleey0Thread starterPA · Oct 9, 2010#100
Thanks.for.that i guess.

I just want learn and.help the community.

Just because i havent.started.yet doesn't mean i cant gain some knowledge.

I.am.doing.like u told me to.

Aras, one minuteu tell me.to call arias and.aem and now you.are.telling me my threads are.worthless.

I.dont.get u sometimes bro.

Why be nice.too me in emails and.then put me down in my own hreads?

Instead, share your knowledge here and help.

Confusing.as.sbit.

Help me or.dont. i thought you were helping and.then.tbis?

You have a split personality bro....