Yarisworld Archive

Zage Turbo Kit Install - Toyota Yaris

159 posts · 460,897 views · page 3 of 4

Replies continued

A-Dingo-Ate-My-Babyearth · Oct 9, 2011#101
worlds worst welding job
pimp my yarischicago · Oct 9, 2011#102
On a second look U may need to have it rewelded at the crack because its on the bend. And have the flex joint installed on the strait portion of the pipe. U can buy flex joints that are only 3-4 inches long.
YodaFL · Oct 9, 2011#103
Weld it right back at the spot and the weld in some support bars. It wont break after that.
Focus_Sh1ftThread starterNew Jersey · Oct 10, 2011#104
Thanks guys. I literally had it repaired an hour after I posted that up lol. Obviously it's going to be a temporary solution, and I'm especially worried about that other weld joint. Definitely liking the mesh flex joint though. Next time it breaks I'll have one added.

If I had a compressor I would definitely do leak testing... Anyone know of a place that rents em out? Otherwise, I'll just have a tuner look for leaks while we're tuning.
ilikericesavannah, ga · Oct 10, 2011#105
A compressor is a wonderful thing to invest in. I bought mine from Harbor Frieght about 6 years ago and is still compressing 235psi weekly. If you are able to get a hold of a compressor check this thread out to make your own 5 dollar boost leak tester:

http://www.dsmtuners.com/forums/arti...your-to4e.html

DSM guys are awesome when it comes to help with turbo's for cheap. I made something like this for my crx. easy to use, easy to make
Focus_Sh1ftThread starterNew Jersey · Nov 12, 2011#106
So last week I took the turbo out to check for shaft play since it's been in now for a little over a year. Also had to remove a broken stem from where the downpipe mounts up. Been putting this off for awhile because taking the turbo off this car is such a god damn burden lol.

Anyway, shaft play is just dandy which I was glad to see. I've also made some progress on my ongoing boost leak battle. I believe the problem is on the exhaust side - specifically where the manifold mounts up to the block. That broken stem wasn't exactly helping either. AND it turns out when I originally reclocked the turbo I had stretched the actuator and thus put preload on the spring (oops :p). When I get time I need to check it out more.
pimp my yarischicago · Nov 13, 2011#107
Exhaust leaks suck. I have had my share.
Focus_Sh1ftThread starterNew Jersey · Nov 25, 2011#108
More problems...

I'm misfiring BADLY. Literally if I even get on the throttle moderately it completely misses and almost stalls. I can't even build past like 1.5 psi of boost (even if I accelerate slowly...). Gas quality wasn't the problem so hopefully it's something plug related. The plugs are less than 10k miles old so I can't imagine they would already be fouled. No diagnostic codes either.
cali yarisCanoga Park, CA · Nov 26, 2011#109
Check the coils too.
fnkngrvIn The Hotbox · Nov 26, 2011#110
Originally Posted by cali yaris ↑
Check the coils too.

+1
Focus_Sh1ftThread starterNew Jersey · Dec 4, 2011#111
Went to go work on the exhaust leak today. In the process I immediately noticed the actuator had no spring pressure. As soon as I started toying with it, the rod fell right out of the actuator. Unbelievable... I can't figure out how to get it back in (if even possible) so it looks like I'll be buying a new one. The best part is that Zage torqued the actuator bracket bolts so hard that I broke the heads off of BOTH of them trying to get them out.
Bluevitz-rsOshawa, Ontario, Canada · Dec 4, 2011#112
Sounds like the Zage kit is adding up to be a "get what'cha pay for" kind of kit after a few thousand miles have been put on it. Unfortunate.
cali yarisCanoga Park, CA · Dec 4, 2011#113
^ With a warranty. Interesting that no one asks.
Bluevitz-rsOshawa, Ontario, Canada · Dec 4, 2011#114
Oh well that changes my view a bit. But there has been quite a few issues.

Garm, we're you still putting together your own kit?
Bigbadturboguyorlando · Dec 4, 2011#115
The kit is cheaply made. You do get what you pay for. But if your looking for an enexpensive way for a little fun it's about the only way to go out of the box. Good luck on a warranty.


There is a new kit in the works with a Precision Turbo and a Haltech Sprint 500 with plug and play harness on its way out. And it's even coming with a tune already built in!
Focus_Sh1ftThread starterNew Jersey · Dec 5, 2011#116
Yeah I'm definitely a little disappointed but it isn't THAT big of a problem. Given all the little problems over the last year it's clear that this isn't the best kit, but the price is completely fair.

Garm - I didn't buy the kit from you lol. Even if Zage does have a warranty, I don't have the time to wait on shipping from Indonesia.
cali yarisCanoga Park, CA · Dec 5, 2011#117
Good luck on a warranty.
Thanks Aras/xbgod, but I really do have warranty turbos on the shelf for my customers. It's how we roll at Micro Image.

@ focus, I can probably do a warranty anyway, and deal with Zage directly for you.
Bigbadturboguyorlando · Dec 5, 2011#118
Its great you warranty the Turbo for them, I would too as long as it was manufacture related. However I wouldn't, Sell a kit that anyone can call and get direct from Zage for 1,100.00. And 200.00 for freight direct from them. They cut their dealers right out. Just go to alibaba.com they sell right there to anyone. Even that light weight pulley your selling you can buy it from there to for 20-25 dollars depending on which Chineese manufacture you want to buy from.
cali yarisCanoga Park, CA · Dec 5, 2011#119
^ And get no service and no warranty. That would be a stupid choice as a customer.

I would too as long as it was manufacture related.
I guess we'll see about that, Aras. I hope so.
ilikericesavannah, ga · Dec 5, 2011#120
Customer service FTW.
cali yarisCanoga Park, CA · Dec 5, 2011#121
Even that light weight pulley your selling you can buy it from there to for 20-25 dollars depending on which Chineese manufacture you want to buy from.
Incorrect. Mine is 100% designed and made in the USA. 👍
Focus_Sh1ftThread starterNew Jersey · Dec 5, 2011#122
Had to drill the bolts out. I tried to tap the holes and failed... I guess I should get a competent mechanic to do it for me? Otherwise new actuator is on the way. I'm just wondering how long that previous actuator has been screwing my boost...
cali yarisCanoga Park, CA · Dec 6, 2011#123
^ I would with any part that matters. You're more mechanical than I am, but tapping should be done right, I think.
Focus_Sh1ftThread starterNew Jersey · Dec 8, 2011#124
Alright everything's back to normal. I definitely hope this is the last time I say this but - I'm going to try and get the ignition tuned and up on the dyno to find the remaining leak(s).
cali yarisCanoga Park, CA · Dec 9, 2011#125
"yaayyyy!"

Picture not included in this copy
maxthehaxQuebec · Feb 16, 2012#126
I understand you so much Lol!

People can say what they want, but I dont think the kit is cheap. People who say things like that have never really experienced what it is to put a turbo on a uncomom car! There is always a little something to tweak, and only with time you will fix every little things. But you need to live them before!

I have my own turbo kit that I run for about 6 months now, with only a base tune on Aem FIc. And still now I have never really feel the real potential on the car because I cannot... First of all I put a too small turbo 2 times! and now waiting for the good one (well I think this time is good!)...

Anyway, not gonna write all my life :P Just wanna wish you a good luck!
Focus_Sh1ftThread starterNew Jersey · Nov 21, 2012#127
Updated this also. It's been 2 years and four months now and things are going quite well. Here are the problems I've had with the kit so far

-Oil return. Tapping the block proved to be the better option
-BOV. Quality is questionable and I would recommend an aftermarket one.
-Actuator broke. Replacing it was easy and only $20. Finding the right size bracket can be tricky though.
-Downpipe weld gave out. Local mechanic welded it back up same day free of charge.
-Worm-gear clamps are sub-par. I had a crap ton of leaks coming from the couplers as a result. I'd recommend replacing them with t-clamps.
-One of the clamps actually sheared a hole in my AC line (down by the radiator/ac compressor). This can probably be attributed to user error.
cali yarisCanoga Park, CA · Nov 21, 2012#128
whoa. Thread revival. I miss my tC.
Focus_Sh1ftThread starterNew Jersey · Nov 22, 2012#129
Heya Garm!

You'll be happy to know the tC is in GREAT condition. I definitely commend you for building such an amazing car. She's currently sleeping in the (heated) garage for the winter, but come spring she'll be spending a decent amount of time at the track I hope. 😁

I'll do some updates in the spring. I also need to make an attempt to get back into the community here... Glad to see some more people have turboed, but let's be real - there needs to be many more turbo yaris owners! 😛

BTW, I'm going to need some "goodies" from you in a few days.
cali yarisCanoga Park, CA · Nov 22, 2012#130
^ Happy to accomodate! and GREAT to see you online again. 👏
kounj · Nov 23, 2012#131
Focus_sh1ft we will have to do a turbo yaris meet when I get mine finished.
jb1Fort Benning, Ga · Apr 11, 2013#132
this thread was sofa king helpful mane. how much HP did you get out of this ???????
TheEggYariswatertown, NY · Apr 30, 2013#133
Focus I was wondering does the Boomslang Plug 'n Play Wiring Harness simplify this process at all?
fnkngrvIn The Hotbox · May 1, 2013#134
Originally Posted by TheEggYaris ↑
Focus I was wondering does the Boomslang Plug 'n Play Wiring Harness simplify this process at all?
You only currently have 2 options which will run you about the same amount of money which was proven by a member (CTScott):

1) Boomslang - breaks the heart and bank, but it is a plug and play which has different options for which management you use be it one of the piggybacks or a standalone. You essentially are injecting the PnP harness in the middle of things with certain wires either tapped or intercepted for signaling. The ends on the harness have male/female where required when it comes to plugging into the factory harness and the stock ECU. The BSlang also has a jumper to be able to run the car if needed without the management plugged in.

2) Custom Harness - time consuming and you had best have a lot of wiring knowledge.
Martinezn.964Tucson · Oct 14, 2014#135
Maybe i missed it but im curious how much hp have you gottn it on the dyno?😳
joyahmed3244south east asia · Jan 2, 2017#136
hey is it on cvt trans?? is it possible on normal cvt transmission with modding anything? i have a 2011 jdm gs vitz
LeprKoRnSydney, Australia · Jan 4, 2017#137
Hey Focus,

I contacted Zage about the kit. I pointed out the fact (made no reference to you) that drilling and tapping of the block was required back when you fitted the kit in 2010 for oil return due to excess blow by. Apparently they use a different, larger hose setup now.

Do you think this would remove the issue you experienced?

Cheers
Lep

Sent from my SM-G920I using Tapatalk
bambam28Puerto Rico · Jul 7, 2017#138
Bump!
JerkrattFair Lawn, NJ · Apr 9, 2018#139
Anyone have the ability to re upload the pictures in this thread?
Kaotic LazagnaCentral Valley, CA · Apr 10, 2018#142
Originally Posted by Jerkratt ↑
Perfect! Ty!
No problem. I wasn't sure if you were looking for the install guide pics, or other pics in this thread. 😆
xDiiThyAustralia · Sep 4, 2018#143
Hey Guys!

I have a 2013 Yaris and am looking at boosting as well! Looks like the Zage kit I might as well skip and go get a custom kit. These 2013 yaris are still running the 1.5L 1NZFE's
DarkShadowFoxMassachusetts · Sep 13, 2018#144
is this 4AT U340E/U341F safe? someone told me the trans can handle an extra 50-100 hp. :T
JerkrattFair Lawn, NJ · May 7, 2020#145
Originally Posted by Kaotic Lazagna ↑
No problem. I wasn't sure if you were looking for the install guide pics, or other pics in this thread. 😆
btw little update...👍

5 attachments not included in this copy

06YarisRSFredericton, New Brunswick, Canada · May 8, 2020#146
Originally Posted by Jerkratt ↑
btw little update...👍
Nice! 👍
JerkrattFair Lawn, NJ · May 24, 2020#147
Did a last minute look over yesterday as well as an oil & plug change. Car is set for drop off for tune the weekend of June 1st. *crosses fingers*

*edit* the wiper arms where installed incorrectly by the shop that worked on it last. They have been swapped since this picture.

1 attachment not included in this copy

06YarisRSFredericton, New Brunswick, Canada · May 24, 2020#148
I bet you're getting excited for June 1. 👍
JerkrattFair Lawn, NJ · May 24, 2020#149
Originally Posted by 06YarisRS ↑
I bet you're getting excited for June 1. 👍
Hell yeah
Kaotic LazagnaCentral Valley, CA · May 24, 2020#150
Nice. Take some videos of the dyno tune pulls.