tiksmanOriginal postAtlanta · Jan 15, 2007#1I purchased these lights from user jimcat here on Yarisworld. They are a great little aftermarket kit. I was very impressed with the fitment.👍
There has been a few tutorials but not to easy to follow. The bulbs that came with them are the stock dim look and I installed some hyperwhites.
Box they came in Picture lost · www.dropshots.com Factory style harness Picture lost · www.dropshots.com harness out of box Picture lost · www.dropshots.com Factory style fog light switch, Factory style plug. Picture lost · www.dropshots.com Rear of light shot Picture lost · www.dropshots.com fog light out of box shot Picture lost · www.dropshots.com Squeeze cilps to remove plastic cover from bumper Picture lost · www.dropshots.com Factory covers removed Picture lost · www.dropshots.com installing in lamp in Bumper only 1 screw is used per side Picture lost · www.dropshots.com Inside bumper shot Picture lost · www.dropshots.com Fogs installed 👍 Picture lost · www.dropshots.com pull up at ebrake handle to remove switch bank Picture lost · www.dropshots.com Switch in place of dummy panel Picture lost · www.dropshots.com Switch installed Picture lost · www.dropshots.com Switch with fogs on. there is no light on the switch when fogs are off not even night illumination Picture lost · www.dropshots.com Without flash Picture lost · www.dropshots.com With camera flash Picture lost · www.dropshots.com Wire Diagram Picture lost · www.dropshots.com http://www.dropshots.com/zoomin.php?...0070106&cimg=3 Bigger photo for diagram link
The only problems I had is there is no instructions and the harness is factory style
and all the plugs look factory but there is no place to hook them up. There are 2 wires a large one going to a fuse and to the relay and a small red wire that is 12 volt feed to power the relay. I used the 12 volt outlet (grey wire) for the red wire and a hard line from the battery to the white wire. The way is works is key on and fog switch on you have fogs with or without headlights this is the way I wanted it. I can even have fogs with brights on.
I think the kit is a good quality kit. I got mine on the cheap (cheaper than ebay)
Jimcat is in Hong Kong and he gives super fast shipping He got it to me in Georgia is about 4 days🤘
UPDATE!!!! READ Carefully
1) On the front harness where can I find the best grounding bolt? I think there is one close to the pass headlamp on the frame rail.
2) What switched 12V source do I hook the red wire up to??
A --Use the grey wire from the 12 volt outlet. It has a plug on it. It is a little hard to reach arround and get to but not to bad. You will have to cut the plug off on the fog harness there is no plug that connecter they have fits into our cars.
3) The wire that the brown thing is connected to, I am assuming that it goes to the battery correct and if so is it + or -?.
A--Large white wire with brown plug, cut it off and put on a connecter to hoof it strait to the battery.
BROWN plug is the same no place to plug it in on a US Yaris.
4) And Lastly where exatly did you mount the relay???
A---I mounted it with a few zip ties behind the glove box.
Also take the wires out of the ac drain tube groment. You will need to extend the wires some into the engine bay. Mount the fog harness from pass to driver (driver being the very end of the harness).
I drilled a hole and picked up a groment off a old Dodge neon radiator mount. Worked great and I dont have to hunt to make it into the engine bay for future wires.
Replies 133
BlenjarCT · Jan 15, 2007#2Thank you so much..I'm, getting mine this wednesday..!
-- Blen
vodkalushRochester, NY · Jan 16, 2007#3very nice
spkrman2 · Jan 16, 2007#4jimcat?
looks sweet!
tiksmanThread starterAtlanta · Jan 16, 2007#5 Originally Posted by
spkrman ↑ jimcat?
looks sweet!
Yes you know the one with the light electric green Yarii
Link to a thread or page that is not in the archive jimcatHong Kong · Jan 16, 2007#6Wonderful 👍
ViolinNew Jersey · Jan 16, 2007#7That's a nice looking kit. I like the adjuster facing downward - not to the back like my eBay version.
What do you mean by 'fried egg' look? They look like standard clear H11 bulbs to me. Most people say fried eggs about yellow/amber lights (which would be nice for a fog). That coating on the tip of the bulb is supposed to be there.
tiksmanThread starterAtlanta · Jan 16, 2007#8 Originally Posted by
Violin ↑ That's a nice looking kit. I like the adjuster facing downward - not to the back like my eBay version.
What do you mean by 'fried egg' look? They look like standard clear H11 bulbs to me. Most people say fried eggs about yellow/amber lights (which would be nice for a fog). That coating on the tip of the bulb is supposed to be there.
I thought the kit was real nice too. It fit very well. I may be mis quoting the fried egg look but to me with my stock headlamps (b4 the hidled units and brighter bulbs) they looked like yellow dim fried eggs. the fogs are the same they need some hi intensity white h11 lamps.
rwseattleSeattle, WA · Jan 16, 2007#9I purchased these too, great set. Easy to install, 2 hours.
Chiefy707707 Cali USA · Jan 21, 2007#10Cool isht! I just installed what looks to be basically the same set on my Yaris last night. Where did you route your harness through to get inside the car? I took mine through the parking brake cable hole (had to cut a small groove in the grommet so it still seals even with the wire fed through. Cut off about 18" of the plastic insulator so it could fit but put it back on when the wire was fed through.) I couldn't figure out what the brown connector and white connector plugged into so I just spliced them into the power wire for the 12v outlet. My fogs came with hyperwhite bulbs though. Pix soon.
Now as for those CQ Lighting HID's and JDM Vitz tailights...
tiksmanThread starterAtlanta · Jan 21, 2007#11 Originally Posted by
Chiefy707 ↑ Cool isht! I just installed what looks to be basically the same set on my Yaris last night. Where did you route your harness through to get inside the car? I took mine through the parking brake cable hole (had to cut a small groove in the grommet so it still seals even with the wire fed through. Cut off about 18" of the plastic insulator so it could fit but put it back on when the wire was fed through.) I couldn't figure out what the brown connector and white connector plugged into so I just spliced them into the power wire for the 12v outlet. My fogs came with hyperwhite bulbs though. Pix soon.
Now as for those CQ Lighting HID's and JDM Vitz tailights...
Check the brown Plug (larger wire be sure to get power dirrect from the battery or you may overload the wires and a start a fire. the larger is 12v constant dirrect from battery and the smaller wire is 12 volt swiched (got that from the 12v outlet grey wire). I did not want to cut any boots or wires so I drilled a hole in the firewall and I used a rubber washer I had from one of my Dodge neon projects ( it was off the upper radiator support). It fit perfectly and now I do not have to wory about installing new stuff under the hood and into the interior.
gonzo452001French Lick,IN · Jan 22, 2007#12I got some ordered from jim cat .How do you get to the power port wires been looking around to see how to take it apart even in the yaris repair manual thanks for any help
ASHRAFHouston, TX · Jan 22, 2007#13thanx for the useful topic
if it was one month before, I might saved 200 or so on my installation
I had mine installed last month
I've just noticed something strange
water, or water vapour (not really sure) is getting into the fogs
anyway ton clean it up and avoid that in the future
tiksmanThread starterAtlanta · Jan 22, 2007#14 Originally Posted by
gonzo452001 ↑ I got some ordered from jim cat .How do you get to the power port wires been looking around to see how to take it apart even in the yaris repair manual thanks for any help
Take out the console. 1 10 mm bolt inder the rear cup holder. Then reach under and unplug the power port.
Also I have had no water issues (been raining here like crazy). But with some aftermarket lens housingd it is a good idea to run a bead of silicone along the edge of the lens and housing. My old Dodge Neon APC tails leaked like crazy inside had to seal them up.
My fogs looked well made and well built and I am picky. I did not buy on ebay because thay wanted too damm much.
ViolinNew Jersey · Jan 25, 2007#15Ooohhh....
Yellowwwww....
Nice.
MrMondayNiteNY/NJ · Jan 25, 2007#16Just received mine Yesterday, will install when it warms up a little. Thanks Jimcat.
vodkalushRochester, NY · Jan 25, 2007#17yah the day i got mine it started snowing... sucks to not have garage to work in :-/
TreyzLong Island, NY · Jan 30, 2007#18 Originally Posted by Yaris TTE JWRC ↑
I got mine installed too, i love them.
Attachment 2965
😲 Where did you get that amber paing paint? Looking to do that as well with the fogs since I can't find just the lens ...
Yellow Fog Lights?- Attachment 2965 · not saved
TreyzLong Island, NY · Jan 30, 2007#19 Originally Posted by Yaris TTE JWRC ↑
I bought it in a Auto store here in CA, they carry alot of import stuff, reg auto stores dont carry it, you have to rescarch it online to see who's selling it.
lol thank god the company that makes it is written in english .. off to google ..
TreyzLong Island, NY · Jan 30, 2007#20You da man! 👍
BlenjarCT · Jan 30, 2007#21o sweet..ya u da man!!!
hey was it easy to install the fogs?
how do you remote the caps?
and how do you put the cable into the dummy place in the car?
-- Blen
jimcatHong Kong · Jan 31, 2007#22 Originally Posted by
MrMondayNite ↑ Just received mine Yesterday, will install when it warms up a little. Thanks Jimcat.
you're welcome 🙂
as400g33kAustralia · Jan 31, 2007#23got mine too, jimcat.. Thanks, mate!
spkrman2 · Feb 1, 2007#24what difference to foglights make?
iven ever had tem
BlenjarCT · Feb 1, 2007#25 Originally Posted by Yaris TTE JWRC ↑
it wasnt too easy, because i had to run the wires from the cabin, to the engine bay, to remove the caps u have too take off the wheels and open up the under wheel guards to push it from inside to outside.
Hey u think u can make a written DYI...step by step? msg it to me...i dont want to pay 60 bux for sum1 to do it...
-- Blen
SpeedzBrisbane, Australia · Feb 1, 2007#26Hey Jimcat...
Mind if you tell me what is the retail price of the fog light in HKD? Ebay retails for about AUD $200-250 including postage...
Cheers
vodkalushRochester, NY · Feb 1, 2007#27I'm planning on doing a DIY guide for this install... but the cold temps and lack of garage has stopped me from installing them 🙁
MrMondayNiteNY/NJ · Feb 1, 2007#28 Originally Posted by
vodkalush ↑ I'm planning on doing a DIY guide for this install... but the cold temps and lack of garage has stopped me from installing them 🙁
I'm in the same boat, wanna install, but too cold.😠 Hopefully it'll get warmer in March.🤷 I'll try to wait for your DIY install though.
TreyzLong Island, NY · Feb 1, 2007#29lol suck it up ... I'm doing an engine swap in the cold.
jimcatHong Kong · Feb 3, 2007#30 Originally Posted by
as400g33k ↑ got mine too, jimcat.. Thanks, mate!
enjoy it 😁
jimcatHong Kong · Feb 3, 2007#31 Originally Posted by
Speedz ↑ Hey Jimcat...
Mind if you tell me what is the retail price of the fog light in HKD? Ebay retails for about AUD $200-250 including postage...
Cheers
see PM...
St_GMemphis, TN USA · Feb 6, 2007#32PM sent, Jimcat.
BlenjarCT · Feb 6, 2007#33do a DIT with every steps...pictured!!!!!
thx in advance..i want my yellow fogs now.
question:
paint lens yellow or get yellow bulbs?
-- Blen
vodkalushRochester, NY · Feb 7, 2007#34yellow bulbs!!!!
SpeedzBrisbane, Australia · Feb 8, 2007#35 Originally Posted by Yaris TTE JWRC ↑
yes, indeed, but too late for the fog lamps, because i have already painted and installed.😳
Is there anyway you can post a pic with only fog lights being switch on against a wall at night time would be great? I would like to see the beam pattern... 👍
Anyone reading this thread and installed jimcat's fog lights could anyone post a pic with only fog lights switch on against a wall at night time too would be great !!!
vodkalushRochester, NY · Feb 8, 2007#36 Originally Posted by
Treyz ↑ lol suck it up ... I'm doing an engine swap in the cold.
yah... the -10 and below wind temps over the last week or so has made outdoor life into 10sec intervals (between my car and wherever I'm going to)
I've been pondering the idea of just going to a self carwash place and using the nice roofed cemented floor.....
jimcatHong Kong · Feb 8, 2007#37 Originally Posted by
vodkalush ↑ yah... the -10 and below wind temps over the last week or so has made outdoor life into 10sec intervals (between my car and wherever I'm going to)
I've been pondering the idea of just going to a self carwash place and using the nice roofed cemented floor.....
it seems most of friend are not yet installed the light
Hopefully will get warmer soon... to finish this job
jimcatHong Kong · Feb 8, 2007#38 Originally Posted by
vodkalush ↑ yellow bulbs!!!!
I think if it is HID 3000k kit will be better.
YarisMaxConcord, · Feb 8, 2007#39nice fog lights!! Where did you get the aux. switch?
SpeedzBrisbane, Australia · Feb 9, 2007#40Is there anyway you can post a pic with only fog lights being switch on against a wall at night time would be great? I would like to see the beam pattern...
Anyone reading this thread and installed jimcat's fog lights could anyone post a pic with only fog lights switch on against a wall at night time too would be great !!!
Cheers
nick1983Winnipeg Manitoba · Feb 9, 2007#41I want to get a set for my sedan....
sf180thWauseon, OH · Feb 9, 2007#42I installed some I got off of ebay, they fit perfectly and are pretty bright I will take a picture of them on for you give me a minute.
sf180thWauseon, OH · Feb 9, 2007#43Here are the lights on, may not be best pics but will get the point across.
SpeedzBrisbane, Australia · Feb 10, 2007#44Sorry for being rude... it seems that the left fog light light cut off is abit dodgy compared to the right side...🤷
But anyway thank you for the image... and you convinced me to part with my cash...👍
sf180thWauseon, OH · Feb 10, 2007#45hey no problem, I had the whole front off four days ago installing my CAI, I might have jared the lights a bit, just need to re-adjust it.
jimcatHong Kong · Feb 11, 2007#46 Originally Posted by
sf180th ↑ I installed some I got off of ebay, they fit perfectly and are pretty bright I will take a picture of them on for you give me a minute.
wow... it pretty good.
How much is it from ebay ??
sf180thWauseon, OH · Feb 11, 2007#47SpeedzBrisbane, Australia · Feb 11, 2007#48Only thing Im concern about is whether different brand housing will affect the beam pattern cut off...
Dont want one which shoots the beam everywhere but the bitumen... LOL
sf180thWauseon, OH · Feb 11, 2007#49The new inserts for the lights look just like factory ones so I dont think the cut-off would be any diffrent from stock.
gonzo452001French Lick,IN · Feb 11, 2007#50I installed my fog lights today got them from jim cat .I hooked mine up to the park lights or running lights anyway the little light in the Headlight.I put the relay and fuse under the fog light switch never even had to take the console out.will try them out in the morning going to work