I'd be careful, doesn't seem to safe!!Originally Posted by gonzo452001 ↑I installed my fog lights today got them from jim cat .I hooked mine up to the park lights or running lights anyway the little light in the Headlight.I put the relay and fuse under the fog light switch never even had to take the console out.will try them out in the morning going to work
DIY Ebay fog lights
134 posts · 129,991 views · page 2 of 3
Replies continued
Got mine in the mail today (Thanks Jimcat, that was amazingly fast service). Now I just have to decide whether I'm up to the task if installing them myself or not.
If by safe you mean heat build up .I drove to work this morning about 34 miles with the fog lights on didn't feel any heat on the center console.I really like them seem real bright better than i thought they would thanks! Jim Cat
Originally Posted by sf180th ↑Here is a link from the company I bought them from. This is a current auction and the buy it now is $86.00.
http://cgi.ebay.com/ebaymotors/06-07...5562QQtcZphoto
Is this USD86.00 included shipping ???
Its very nice 👏Originally Posted by St_G ↑Got mine in the mail today (Thanks Jimcat, that was amazingly fast service). Now I just have to decide whether I'm up to the task if installing them myself or not.
No, the shipping on that auction is listed as $20.
Originally Posted by jimcat ↑Is this USD86.00 included shipping ???
OK after remembering to search for the spray that Yaris TTE JWRC posted .. here is what I finally found ...
http://www.tunerzimage.com/Vans-yell...-lenspaint.htm
Picture lost · www.tunerzimage.com
Did you pay that much for this bro?
http://www.tunerzimage.com/Vans-yell...-lenspaint.htm
Picture lost · www.tunerzimage.com
Did you pay that much for this bro?
Finally put on the fogs and the painted oem mudguards. Here's pics:
Picture lost · i30.photobucket.com
Picture lost · i30.photobucket.com
Picture lost · i30.photobucket.com
No DIY, I just followed the install instructions by the first poster. Difference in mine is I hooked up 12v switched wire to the park lights. That way park lights on (or headlights on), I can switch on/off fogs. If park lights off (or headlights off), fogs are also off. I also put the switch near the side mirror controls. That way all the light switches are within reach of my right hand.
Picture lost · i30.photobucket.com
Picture lost · i30.photobucket.com
Picture lost · i30.photobucket.com
Picture lost · i30.photobucket.com
No DIY, I just followed the install instructions by the first poster. Difference in mine is I hooked up 12v switched wire to the park lights. That way park lights on (or headlights on), I can switch on/off fogs. If park lights off (or headlights off), fogs are also off. I also put the switch near the side mirror controls. That way all the light switches are within reach of my right hand.
Picture lost · i30.photobucket.com
Looks good. Quick question? How did you get the wiring from the engine compartment into the cabin? Did you enter trough the firewall? Did you add additional length to the original wiring? Thanks.
I used the hole that is used by the tube that leads the water out of the aircondtioning system. This hole leads to the engine bay. I cut a small piece out of the rubber to allow the wires through. I placed the wires above the tube so that the water won't drip into the wires. Bear in mind, RHD setup is quite different from LHD so the hole I'm talking about might be in a different place for LHD versions.Originally Posted by rwseattle ↑How did you get the wiring from the engine compartment into the cabin? Did you enter trough the firewall?
Yes. The original wiring was insufficient to set up properly. You'd probably need about several meters of wire:Originally Posted by rwseattle ↑Did you add additional length to the original wiring? Thanks.
- about 1.5 meters for the thick black 12v wire connecting to the + battery terminal
- about 2 meters for the thick red 12v wire connecting to the fog lights
- about 2 meters for the thick red switched 12v wire (I used the same thick red ones but you can use thinner ones) to reach the park light wires near the headlight assembly.
- about 1 meter of the ribbed tube to cover the wires.
Instead of splicing wires, I used connectors and a crimper to make it safe and secure.
oh and thanks jimcat for the fog lights and thanks violin for the mud guards!
Great. Thank for the feedback.
Welcome,Originally Posted by as400g33k ↑oh and thanks jimcat for the fog lights and thanks violin for the mud guards!
so happy to see the result
as400g33k, where did you source the +12V parker light wire? Behind the steering column, behind the glovebox, or behind the headlight itself?
Do your fog lights work in all headlight switch positions (i.e. parkers, low beam, high beam)?
Do your fog lights work in all headlight switch positions (i.e. parkers, low beam, high beam)?
behind the headlight itself.Originally Posted by LoK. ↑as400g33k, where did you source the +12V parker light wire? Behind the steering column, behind the glovebox, or behind the headlight itself?
Yes on all.Originally Posted by LoK. ↑Do your fog lights work in all headlight switch positions (i.e. parkers, low beam, high beam)?
Hi just would like to ask where did you get the fog light covers? From toyota dealer or was it included in the package?
Cheers
Cheers
yep, its included in the package.
Yes, please see PM, thanksOriginally Posted by Speedz ↑Hi just would like to ask where did you get the fog light covers? From toyota dealer or was it included in the package?
Cheers
thanx jimcat, they seem to look great. but, no instructions.... can someone please post up some info on hot to get them in the bumper. my friend will wire them up, but I like doing some things myself. remember, I am a girl 👍 I looked under the bumper, do you remove the center section, or what... any help would be appreciated... I think I may also look into the grounding thing! is it a big help??
Look at the first post in this thread. Installing the lights and the trim pieces in the bumper is the easiest part (I did have to remove both front wheels one at a time to get to the space however)...Originally Posted by jdf01 ↑thanx jimcat, they seem to look great. but, no instructions.... can someone please post up some info on hot to get them in the bumper. my friend will wire them up, but I like doing some things myself. remember, I am a girl 👍 I looked under the bumper, do you remove the center section, or what... any help would be appreciated... I think I may also look into the grounding thing! is it a big help??
Talking tiksman into doing my wiring is the hard part!!! 🍻
Originally Posted by redyaris ↑Look at the first post in this thread. Installing the lights and the trim pieces in the bumper is the easiest part (I did have to remove both front wheels one at a time to get to the space however)...
Talking tiksman into doing my wiring is the hard part!!! 🍻
That should be the easy part 😲
QUESTION:
I have mine installed this way:
Picture lost · i63.photobucket.com
I purchased the base for the bulbs but when i removed the bumper i found that the factory harness and plug was already there, followed the cable inside the dash and removed from the plug, connected that cable to a relay and from the relay to a fuse and that to a live line to the battery. The relay is powered by the key switched line and then to a switch. Problem is that the line marked in red in the diagram gets hot. Is this normal or what should i do to prevent this???
Kitt
I have mine installed this way:
Picture lost · i63.photobucket.com
I purchased the base for the bulbs but when i removed the bumper i found that the factory harness and plug was already there, followed the cable inside the dash and removed from the plug, connected that cable to a relay and from the relay to a fuse and that to a live line to the battery. The relay is powered by the key switched line and then to a switch. Problem is that the line marked in red in the diagram gets hot. Is this normal or what should i do to prevent this???
Kitt
I installed my foglights a while ago but, today I noticed that all the wires feel out of the back of the relay. 4 wires going in to the back of the relay. I've no idea how to put them back together. Anyone? Thx.
Low in should be the line that comes from your switch, low out should be ground, 30a in, from your battery and 30a out should go to your fogs... This is a standard type of relay, they usually have a diagram printed on its side, if you could post a picture of it i may help you better


My PC is not downloading the relay pix. I'm not sure why. I will downloaden tomorrow at work. The relay does not show any wiring diagram. It only says YLE YL-388-S Automotive relay 12V/40A. I got 4 connectors and they're all the same size. I will post pix tomorrow. Thanks for your help.
It should have something like this...
Picture lost · www.rowand.net
post the picture anyways and i'll see what i can do
Picture lost · www.rowand.net
post the picture anyways and i'll see what i can do
Hopefully this helps.

ummmm not that much tough... you will need a continuity tester then to find it out. The 2 connectors that have continuity are ones that will go to the switch and to the ground, the other two ones will come from the fuse to the fog lights...
and try to post a bigger picture to see if it helps, focused on the pins of the relay
and try to post a bigger picture to see if it helps, focused on the pins of the relay
Foglights installed and functional...the best mod for me yet!!!
I found the correct connection. I did use the continuity tester. I will post pictures of working fog lights soon. I'm installing a front strut bar and will post pictures all together. Thank you for your help.
Here a pic of wrk foglights.

😲 very good, you finally made itOriginally Posted by rwseattle ↑Here a pic of wrk foglights.
how much was it?Originally Posted by tiksman ↑Yes you know the one with the light electric green Yarii
Link to a thread or page that is not in the archive
It been a while since I purchaced. I think arround $80Originally Posted by seanele ↑how much was it?
tiksman is no. 1 👍Originally Posted by tiksman ↑It been a while since I purchaced. I think arround $80
Thanks Jimcat for the fog light kit!!! It came in one day ahead of schedule hehe.Will install on Friday night
Ok. Got them installed today. So happy









Hey guys, I think that I am going to try and tackle this myself. Did you have to remove the bumper to install the fog lights?
Thanks,
MYT
Thanks,
MYT
No look at the first pics you can get to the fogs by just undoing the top of the bumperOriginally Posted by myt ↑Hey guys, I think that I am going to try and tackle this myself. Did you have to remove the bumper to install the fog lights?
Thanks,
MYT
I went though the wheel well and front bumper......not very smart but it got the job done and I ended up with a lot of bruises from my arm being squashed in there
Gotcha I guess I was thrown off by your pic on the underside(or back of the bumper). thanks though guys, hopefully I'll get some pics when I finish it up :)
MYT
MYT
wheel well remove the front pushpins and under the bumper remove the three self taping screws wheel well plastic will fold back giving plenty of room i wired direct to bat with inline fuse works fine just don't for get to turn them off
There are also 2 open spades in the fusebox I wired mine to (the top one). Same deal, don't forget to turn off!
I found where just just plug the wires in..... how come every one else could not? I got the same ebay kit everyone else did.... well the one from Jimcat...
Vanderkitten.... actully I found a switched in the fusebox, so they turn off with the ign... and I had to do no cutting, or splicing, all I did was pull the pins out off the supplied connectors and insert them into new ones :)... I wil have a pic up in a few... and it works perfect, and damn near looks stock
Vanderkitten.... actully I found a switched in the fusebox, so they turn off with the ign... and I had to do no cutting, or splicing, all I did was pull the pins out off the supplied connectors and insert them into new ones :)... I wil have a pic up in a few... and it works perfect, and damn near looks stock

Wow Thanks Black Yaris ..... Useful teaching info for meOriginally Posted by Black Yaris ↑
Hey thanks for the fast delivery! Got them in 5 days from Hong Kong, China to Toledo, Ohio!Originally Posted by jimcat ↑Wow Thanks Black Yaris ..... Useful teaching info for me
I want to have HID's as fog lights. Is this possible as of right now?
how were the bulbs that came with the fog lights from jimcat? were they fairly bright? does anyone have a picture of their fog lights at night with the original bulbs ? i wanna know how bright it is since i just ordered a set and i wanna know if i need to replace the bulbs before getting it installed. :] cant wait!
i have jimcat's fog light kit and haven't switched the bulbs yet so here are some pictures.






