15x7 35 offset front w 195/50s and 15x8 25 offset rears w 205/50s
Divorce forces me to modify the Yaris
241 posts · 79,892 views · page 3 of 5
Replies continued
42 days after ordering the sub box finally came......I will get it installed Sunday I hope...
At least for temporary...I gotta go buy supplies and start the interior build
I have to keep the rest of the weight I put in to the car at 114lbs or I go over the stock interior part weight I took out...I am pretty close now with harness bar....sub and box...amp...wires...deadening....
I am certainly gonna try to keep it under....no spare tire but I can get towing and can always call somebody to bring me one off their xB....
At least for temporary...I gotta go buy supplies and start the interior build
I have to keep the rest of the weight I put in to the car at 114lbs or I go over the stock interior part weight I took out...I am pretty close now with harness bar....sub and box...amp...wires...deadening....
I am certainly gonna try to keep it under....no spare tire but I can get towing and can always call somebody to bring me one off their xB....
I will get pictures up tomorrow with daylight......yesturday got sub box bolted in and aimed where I think it iwll work well.....
Tonight got sub hooked to box,bolted in,and hooked to amp......
It was too late to run test tones so I did a best guess at crossover points on amp and fired it up with about 500w.....
It is really nice and clean and loud,once it breaks in I will turn up the power a bit,plus I gotta tune the amp that will take me a good hour to do since it is hard to get at amp knobs.
I really need to work on gettign more deadening in the hatch and roof....it had a bunch of rattles to chase....lol....
Sub builds pressure pretty good,will do much better when all panels are back in car and it is sealed up really good inside.
WEll pictures tomorrow...sorry it took so long to get to this but the rain just wont stop here....
Tonight got sub hooked to box,bolted in,and hooked to amp......
It was too late to run test tones so I did a best guess at crossover points on amp and fired it up with about 500w.....
It is really nice and clean and loud,once it breaks in I will turn up the power a bit,plus I gotta tune the amp that will take me a good hour to do since it is hard to get at amp knobs.
I really need to work on gettign more deadening in the hatch and roof....it had a bunch of rattles to chase....lol....
Sub builds pressure pretty good,will do much better when all panels are back in car and it is sealed up really good inside.
WEll pictures tomorrow...sorry it took so long to get to this but the rain just wont stop here....
Are you going to be able to get this all done by June 5th? 🙂
Oh no....interior will still probably be in pieces,but system will be in and working,it is as of yesturday....
Picture not included in this copy
Picture not included in this copy
I took it out yesturday and went for a cruise....and well with just a basic tune,xovers set to about 80hz on amp and deck.....sub at about 600w to break in......comps at 65w each......
Well lets just say it sounds beautiful,tones are crisp from the comps,and I meen so crisp that my buddy riding shotgun thought in one part of a song I was talking to him,turns out it was a part recorded in the track that he although listening to the song for years had never heard in the track.
Sub.......OMG......excursion is sick...it moves like a kangaroo on crack.....deep clean bass lows,sharp hits,the box is tuned to the sub so it has proper back spacing and airspace to allow full motor movement.
Sealed box and honestly I would be afraid to put it in a ported box......it would hurt bad,it does now in a sealed box.....
If you heard my tC....well this is louder.....stupid louder,the sub volume increases with every volume change.....it has a lot to get broke in but once it does it will be even louder....
As for rattles........once again I seem to have done a pretty good job...only one front to back we found was the rear plate frame.....body panels flex quite a bit.....pressure in car is not too over bearing,but it is there.....had AC on full blast and the sub was pusshing the air in the car back forward just as easily as the AC pushed it out the dash.
voltage,no issues even on the hits.....never went below 13.6v....on stock battery....hwo would of guessed....new battery is gonna be needed I am sure....
Sound out side of car.......almost none....just like tC....but sub does not like hatch open,it get moving too far out and I heard motor slap once or twice so shut hatch and it stopped,my guess is it need the pressure from bouncing off the hatch.....
Components.....they are keeping right up,who would of guessed...DLS is a very nice speaker....lol
All in all I think a years worth of research,some luck,and a lot of work I have a very nice basic system....still got a lot of tuning.....it is all built around driver and passenger positioning,windows up,hatch closed and earplugs in.....
also I should say.......all that is at 50% power,I am afraid to turn up to 75% to totally tune it in till it is broken in......lol....I took it up to 25 on the volume,75% for my deck is like 28 for a burp and it hurt my ears.....I doubt there is any need to go past 50% as the car is so small inside it would not be fun....well it would but you know.
Now to start the pods for the doors and Apillar tweets.....
Picture not included in this copy
Picture not included in this copy
I took it out yesturday and went for a cruise....and well with just a basic tune,xovers set to about 80hz on amp and deck.....sub at about 600w to break in......comps at 65w each......
Well lets just say it sounds beautiful,tones are crisp from the comps,and I meen so crisp that my buddy riding shotgun thought in one part of a song I was talking to him,turns out it was a part recorded in the track that he although listening to the song for years had never heard in the track.
Sub.......OMG......excursion is sick...it moves like a kangaroo on crack.....deep clean bass lows,sharp hits,the box is tuned to the sub so it has proper back spacing and airspace to allow full motor movement.
Sealed box and honestly I would be afraid to put it in a ported box......it would hurt bad,it does now in a sealed box.....
If you heard my tC....well this is louder.....stupid louder,the sub volume increases with every volume change.....it has a lot to get broke in but once it does it will be even louder....
As for rattles........once again I seem to have done a pretty good job...only one front to back we found was the rear plate frame.....body panels flex quite a bit.....pressure in car is not too over bearing,but it is there.....had AC on full blast and the sub was pusshing the air in the car back forward just as easily as the AC pushed it out the dash.
voltage,no issues even on the hits.....never went below 13.6v....on stock battery....hwo would of guessed....new battery is gonna be needed I am sure....
Sound out side of car.......almost none....just like tC....but sub does not like hatch open,it get moving too far out and I heard motor slap once or twice so shut hatch and it stopped,my guess is it need the pressure from bouncing off the hatch.....
Components.....they are keeping right up,who would of guessed...DLS is a very nice speaker....lol
All in all I think a years worth of research,some luck,and a lot of work I have a very nice basic system....still got a lot of tuning.....it is all built around driver and passenger positioning,windows up,hatch closed and earplugs in.....
also I should say.......all that is at 50% power,I am afraid to turn up to 75% to totally tune it in till it is broken in......lol....I took it up to 25 on the volume,75% for my deck is like 28 for a burp and it hurt my ears.....I doubt there is any need to go past 50% as the car is so small inside it would not be fun....well it would but you know.
Now to start the pods for the doors and Apillar tweets.....
Also thanks everyone who has checked this thread......I know it is taking forever,parts cost a lot and I am a poor man.....with a teenage son who never stops eating...lol
The car gets people looking everywhere......I will do my best to rep the Yaris/Vitz....and build a car that will make us all go wow.....that is sweet.
The car gets people looking everywhere......I will do my best to rep the Yaris/Vitz....and build a car that will make us all go wow.....that is sweet.
Well started door pods for the comps saturday,after about 24 hours of work in 3 days they are starting to take shape.....
4 layers glass of a tshirt
Picture not included in this copy
Picture not included in this copy
Bondo starting to take shape
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Several layers liquid sound deadener on inside
Picture not included in this copy
Picture not included in this copy
I will have more pictures in a few days,these bolt in place over the stock speaker area and will pass through the panel and into the door.Speakers DLS UP6 Ultimates
Apillar for the tweeters still to begin next weekend.
4 layers glass of a tshirt
Picture not included in this copy
Picture not included in this copy
Bondo starting to take shape
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Several layers liquid sound deadener on inside
Picture not included in this copy
Picture not included in this copy
I will have more pictures in a few days,these bolt in place over the stock speaker area and will pass through the panel and into the door.Speakers DLS UP6 Ultimates
Apillar for the tweeters still to begin next weekend.
Here is the last 24 hours work....my first set of pods I built from scratch and so far so good....lot of work to do....
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
couple of installed pics....had to take the DLS out as I blew a comp accidently grounded it out....
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
nice
Thanks Man........I am really happy I just picked up a set of Takata harness good till 2013 for $450 pick then up tomorrow,no mid pipe and header this month but Takata.....gotta do it......just gotta pick up the right eye bolts to mount to harnes bar and seat frame...think it is 7/16" threads,one set of 4 in 1" length and one set in 2" length for harness bar....lol....they are worth more than the seats and brackets....win win...🎉
pictures up tomorrow night of them...4 point with latches on all 4 points hence the need for the eye bolts.....
pictures up tomorrow night of them...4 point with latches on all 4 points hence the need for the eye bolts.....
That is such excellent handiwork. Well done. Out of curiosity, do you work in WWU?
Nope I work for Sears as an Electrician and Building Maintenance.
are you by chance going to the Mt St Helens cruise this weekend,we got a few Yaris headed that way,it started with the Scion guys a few years back,but all makes are welcome,good cruise,good fun,good food,and great people.
Yeah it has been a long week building them,still got a few touchups on the base shapes to fit door panel perfect and paint but all in all they are sounding great,still got the Apillars to do for tweeters,but I havn'e found the right angle I like for them yet....lol....I hate tuning a system to the car...takes forever.
are you by chance going to the Mt St Helens cruise this weekend,we got a few Yaris headed that way,it started with the Scion guys a few years back,but all makes are welcome,good cruise,good fun,good food,and great people.
Yeah it has been a long week building them,still got a few touchups on the base shapes to fit door panel perfect and paint but all in all they are sounding great,still got the Apillars to do for tweeters,but I havn'e found the right angle I like for them yet....lol....I hate tuning a system to the car...takes forever.
wanted to share here first......takatas....REAL TAKATAS.....lol
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
At this point you should probably just remove your rear seatbelts.
and put a turbo in
got harness eyebolts in today,one goes perfectly where the seatbelt goes to the car at the floor and the other screws intothe wedge seat bracket where the seat belt clip end goes....then I drilled the harness bar and used some Schroth clips and new bolts to pass through the bar and got them hooked in now.....I will get some pictures tomorrow,came out really good.
Sorry it has taken me so long to update the car.....camera broke so I will have to bum a camera....
So I inverted the sub on the box on the 4th and it sounds even better.....
Got a Password JDM battery tiedown in blue from my buddy for helping him hook up his sub.
Got a set of SToptech drilled front rotors and a set of Hawk pads
And just ordered today from MI a 23mm rear sway and white ball delrin shift knob.
Just kinda waiting for the Nitto midpipes to arrive and hope I still got enough cash on hand to buy without hitting up my credit card....either way it is gettign bought....lol
May of found me a CF engine cover off an xB for cheap....fingers crossed
Interior still sitting in my living room along with a bunch of other parts like the stock seats,wheels,and tools everywhere.....but I am making progress....
Car is really fun to drive now that wheels and stereo are in and working....
Saving up for airride.....camber.....and new struts....eating bean and cheese burritos this summer to cut costs....may even quit smoking cigs so I save another $250 a month.....I really want airride.....really bad.
So I inverted the sub on the box on the 4th and it sounds even better.....
Got a Password JDM battery tiedown in blue from my buddy for helping him hook up his sub.
Got a set of SToptech drilled front rotors and a set of Hawk pads
And just ordered today from MI a 23mm rear sway and white ball delrin shift knob.
Just kinda waiting for the Nitto midpipes to arrive and hope I still got enough cash on hand to buy without hitting up my credit card....either way it is gettign bought....lol
May of found me a CF engine cover off an xB for cheap....fingers crossed
Interior still sitting in my living room along with a bunch of other parts like the stock seats,wheels,and tools everywhere.....but I am making progress....
Car is really fun to drive now that wheels and stereo are in and working....
Saving up for airride.....camber.....and new struts....eating bean and cheese burritos this summer to cut costs....may even quit smoking cigs so I save another $250 a month.....I really want airride.....really bad.
23mm rear sway installed today and stoptech rotors and Hawk pads a few days back.
Drives like a whole differnat car now,way better feels stable at all times,no lean anymore,steering is crisp now....
I have to say it may be my favorite mods yet......also if you have like 8" wide rims like me you may have to pull one wheel off to get bar in place .....but total install of it took maybe 30 min.
Would of been quicker but my 14mm wrench broke while loosening the shock bolt,flew out and hit me in the face,gave me a minor black eye....👎
Drives like a whole differnat car now,way better feels stable at all times,no lean anymore,steering is crisp now....
I have to say it may be my favorite mods yet......also if you have like 8" wide rims like me you may have to pull one wheel off to get bar in place .....but total install of it took maybe 30 min.
Would of been quicker but my 14mm wrench broke while loosening the shock bolt,flew out and hit me in the face,gave me a minor black eye....👎
Camera broke or I would post up the last months work......next pictures will be on 8/14 at Toyota Fest.......trying to get car as close to back together as I can by then,will still be a work in progress,but I still and gonna bring what I built and hope it is enjoyed.....
So this month I installed the 23mm rear sway......wow.....car rides so much better,springs still suck,DF210s....too soft,but airbags will fix that thsi Winter....plus a set of Tokico's will help....
Then I got a set of the Depo JDM lights from Garm,fitment is actually as good as my stock lights were,one washer to shim the top bolt on drivers side and near perfect fitment.....the look is so much better though.....
Took some truck bed liner and used it on the pods and the sub box,give them a bit of durability as I stuff crap in the back all the time and the pods get kicked here and there,deadened the inner pods and made a tube to go from pod to inner door,sounds incredable.....
then I made pods in the A pillars......got them half way done,but the tweets went in finally and OMG....what a differance....also incredable....
Put some Polyfill in the sub box,but put too much and the hit got softer while the presence got more full....so took it all out but 2oz,which is still a lot and now it hits again and the presence is very full and crisp.....
Most the rear interior is back in the car,B pillars still need glassed and cut to fit harness bar....
Rear floor still not started but that will be a winter project I guess as the air ride stuff starts to come in....fit it as I go...hate being poor.....
Still got a CF shift bootie to install and vinyls for my sponser and for microimage on the rear side of seats along with the stereo vinyls for Pioneer and JL all in white and then that will be surronded by Gunshow guns from rogue status.....should come out nice.
Car is coming along....figure another year and it should be close to done....maybe 18 months of hard work...lol
So this month I installed the 23mm rear sway......wow.....car rides so much better,springs still suck,DF210s....too soft,but airbags will fix that thsi Winter....plus a set of Tokico's will help....
Then I got a set of the Depo JDM lights from Garm,fitment is actually as good as my stock lights were,one washer to shim the top bolt on drivers side and near perfect fitment.....the look is so much better though.....
Took some truck bed liner and used it on the pods and the sub box,give them a bit of durability as I stuff crap in the back all the time and the pods get kicked here and there,deadened the inner pods and made a tube to go from pod to inner door,sounds incredable.....
then I made pods in the A pillars......got them half way done,but the tweets went in finally and OMG....what a differance....also incredable....
Put some Polyfill in the sub box,but put too much and the hit got softer while the presence got more full....so took it all out but 2oz,which is still a lot and now it hits again and the presence is very full and crisp.....
Most the rear interior is back in the car,B pillars still need glassed and cut to fit harness bar....
Rear floor still not started but that will be a winter project I guess as the air ride stuff starts to come in....fit it as I go...hate being poor.....
Still got a CF shift bootie to install and vinyls for my sponser and for microimage on the rear side of seats along with the stereo vinyls for Pioneer and JL all in white and then that will be surronded by Gunshow guns from rogue status.....should come out nice.
Car is coming along....figure another year and it should be close to done....maybe 18 months of hard work...lol
Totally forgot......Nitto midpipe went in as well saturday.....wow....fitment is perfect.....sound...well it lost the drone from the Greddy can finally...love it....volume now when I get on it....tickets will come....but cruising speed...very quiet...
Ppwer....feels like from 2000rpm to 5500 it pulls much stronger,winds up a bit faster....but low rpms,feels like some hp has been lost to make flow....but that is really low and if you push gas more it picks right up...
Might be the best buy so far out of...the following
Midpipe
23mm Rear sway
JDM tails
and making the tweeter pods
Midpipe my favorite so far,but stereo install not far behind....sub pounds....make ya grin like a kid pounds in the little car...wish it was all done man....
Ppwer....feels like from 2000rpm to 5500 it pulls much stronger,winds up a bit faster....but low rpms,feels like some hp has been lost to make flow....but that is really low and if you push gas more it picks right up...
Might be the best buy so far out of...the following
Midpipe
23mm Rear sway
JDM tails
and making the tweeter pods
Midpipe my favorite so far,but stereo install not far behind....sub pounds....make ya grin like a kid pounds in the little car...wish it was all done man....
Fingers crossed...should be picking up Kaminari kit Sunday at Toyota Fest....will finally get pictures up Sunday night of car after the show....lots of work still to finish a pillars and clean car.
As promised........pictures from Toyota Fest '11
Got the Kami kit that morning from Foth....it is off the DRift Yaris,gotta get the airride in before I can really use it as it will scrape badly and it is a nice kit.....
Was just me and tylermayer at the show repping the Yari.......
Interior
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Exterior
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Been a long hard summer and worked hard to put it together.....still a long way to go before the picture in my head looks like the car in my driveway......lol
Got the Kami kit that morning from Foth....it is off the DRift Yaris,gotta get the airride in before I can really use it as it will scrape badly and it is a nice kit.....
Was just me and tylermayer at the show repping the Yari.......
Interior
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Exterior
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Been a long hard summer and worked hard to put it together.....still a long way to go before the picture in my head looks like the car in my driveway......lol
In case you wonder how low it really is with the kit,lets jsut say you can put your foot under it ,may be tops 3" off ground at the rear of the sideskirt and front is about the same.
Wow! Great looking car!!!
Nice job!
Nice job!
holy shnikes! your car has changes immensely from post one. looks awesome.
I'm completely in lust with those wheels. what model are they?
I'm completely in lust with those wheels. what model are they?
Thanks very much.......the wheels are Axis OG fronts are 15x7 35 offset and rear are 15x8 25 offset......I found one more picture I think is my favorite....cant wait to start fitting the body kit perfectly and painting....
Picture not included in this copy
Picture not included in this copy
Rear and sideskirts primered and fitted...
Picture not included in this copy
Picture not included in this copy
Wooo nice work man!
Thanks......now to start saving for spring......camber and airbags.....I really want to set it on the ground and I think the Kami kit will make it easy....lol
soooooooooo sick. nice work man
LOL.. i love the little wind up toy thing you have. that's awesome.
DAMNN!!! so sick!! :O
Seriously the next thing on your list needs to be air!!! Everything on your car flows so good!Originally Posted by bzinn 1 ↑Rear and sideskirts primered and fitted...
Picture not included in this copy
Sweet mother of god.Originally Posted by bzinn 1 ↑Rear and sideskirts primered and fitted...
Picture not included in this copy
Wishing the rain would stop....PNW weather is not the greatest this year,I have got the front lip on even though it is still silver and has red and black strip on it....it looks kinda out of place but it is nice to see the car is drivable with the kit.I decided to find the worst places I regularly go and see if I could get in and out without major scape.....so far so good,I did crack the drivers sideskirt at the low point,my buddies driveway is now a fail till baggs....lol
Soon as I get few hours to sand and primer the front lip I will get the car washed up and more pictures taken.It has been a blast to drive the last week with it like this....the local tuner scene has really taken a liking to the car.
there are a lot of necks turning when I goto the grocery store,or pretty much anywhere....it is weird....my tC was the same way..... I need to get a gopro camera and record what goes on at the car while I am not in it....bet it would be funny.....What is it....IDK.....new Hyundai...lol
It is amazing how what has seemed like forever two years have passed since I started modding Egplant....and I still gotta save for a good 6 months for the suspension.
This winter probably by xmas I will have the interior built and finished and ready for the compressors and tank and all the fun lines and wires.
Being a broke father of a 16 year old who eats like the end is near and he is stocking up...lol....I hope he enjoys the day he gets to go take his drivers test in this....its my only car....
Soon as I get few hours to sand and primer the front lip I will get the car washed up and more pictures taken.It has been a blast to drive the last week with it like this....the local tuner scene has really taken a liking to the car.
there are a lot of necks turning when I goto the grocery store,or pretty much anywhere....it is weird....my tC was the same way..... I need to get a gopro camera and record what goes on at the car while I am not in it....bet it would be funny.....What is it....IDK.....new Hyundai...lol
It is amazing how what has seemed like forever two years have passed since I started modding Egplant....and I still gotta save for a good 6 months for the suspension.
This winter probably by xmas I will have the interior built and finished and ready for the compressors and tank and all the fun lines and wires.
Being a broke father of a 16 year old who eats like the end is near and he is stocking up...lol....I hope he enjoys the day he gets to go take his drivers test in this....its my only car....
Took a few more pictures of the progress.....got the Quick Release latches installed,they are kinda over the top,but I am stuck with them now,and I am sure when I get a line leaking I will enjoy the quick off of the bumpers to get at the underside of the car.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Looks incredible!!
What a great job you've done.
What a great job you've done.
i bet your ex wife would be so proud 👍
Haha.....you made my day.....
Best part is she took my tC.....with about $20,000 in parts,a years payments left to go and traded it in for a KIA.....minivan.
I offered her the Yaris but she didn;t want it....she fought me over the tC.....
I am sooooo happy to say I work at the same mall as her one day a week and I park it right at the entrance of the Mall wehre she enters so she gets to see it,no worries it is on LP cameras all day....
Hope she is enjoying the minivan.......I sure love my Yaris
Best part is she took my tC.....with about $20,000 in parts,a years payments left to go and traded it in for a KIA.....minivan.
I offered her the Yaris but she didn;t want it....she fought me over the tC.....
I am sooooo happy to say I work at the same mall as her one day a week and I park it right at the entrance of the Mall wehre she enters so she gets to see it,no worries it is on LP cameras all day....
Hope she is enjoying the minivan.......I sure love my Yaris
Im really liking the new wheels, look 100x better than your old ones.
droooooooooooooooooooooool
Next is pullies....and Neffy interior.....sooner or later I should get off my butt and install the DC header.
Then gotta pull the lip kit and wheels off for winter,hoping it is a short snowless winter
Then gotta pull the lip kit and wheels off for winter,hoping it is a short snowless winter
Lovin how the g ride is lookin! haha
Originally Posted by bzinn 1 ↑Haha.....you made my day.....
Best part is she took my tC.....with about $20,000 in parts,a years payments left to go and traded it in for a KIA.....minivan.
I offered her the Yaris but she didn;t want it....she fought me over the tC.....
I am sooooo happy to say I work at the same mall as her one day a week and I park it right at the entrance of the Mall wehre she enters so she gets to see it,no worries it is on LP cameras all day....
Hope she is enjoying the minivan.......I sure love my Yaris
epic.
very clean car
Todays pully install of the water pump and alternator went great except that when I hooked the battery + back up I heard a pop......car started right up but no tach,no brakelights,no dash lights on the heater controls,no blinkers but flashers worked,no power steering,and car was not charging.....grrrrrr
So the hunt was on to find what popped.....checked everything and it was good.....don't know why I didn't check the fused link on the battery terminal + where the alternator fuse is first.....that was the culprit.
Of course it is a 2 day wait for a new one from Toyota so car is sitting at my buddies DOA...lol
I don't know why it popped to be honest short of there was some corrosion on the bolt that hooked it to the aftermarket terminal or it may of been already partially going out with all the amp and lights and such adding drain to the system.
Car starts but that is about it,hoping that is all that blew for me as it is only a $16 part,we tested all the fuses on the car and they were good,relays seem good,no burnt wires.....thank goodness.
I will get pictures of pullies installed once car is going again on Thursday....wish me luck.
So the hunt was on to find what popped.....checked everything and it was good.....don't know why I didn't check the fused link on the battery terminal + where the alternator fuse is first.....that was the culprit.
Of course it is a 2 day wait for a new one from Toyota so car is sitting at my buddies DOA...lol
I don't know why it popped to be honest short of there was some corrosion on the bolt that hooked it to the aftermarket terminal or it may of been already partially going out with all the amp and lights and such adding drain to the system.
Car starts but that is about it,hoping that is all that blew for me as it is only a $16 part,we tested all the fuses on the car and they were good,relays seem good,no burnt wires.....thank goodness.
I will get pictures of pullies installed once car is going again on Thursday....wish me luck.
so how would one go about avoiding your problem?
That thing looks awesome, nice job!
In answer to the question how to avoid this problem....honestly I think it is just sheer bad luck.I did find that the ground strap wire from the negative terminal to the tranny case was very corroded,could of added to the problem.
Also I think a major part is the aftermarket battery terminal just sucks and may of not had a great connection,also found corrosion in it as well.
Tomorrow the fusable link thing that is attached to the terminal should be at dealership and hoping that is all that popped.We were able to test all functions of the car using this tool that hooks to the battery and supplies power to anything to see if it will work and so far everything worked,which is good because the fuse is only $16.50,hoping it is all that blew,I have bad luck at times....but it is a car and cars tend to Gremlin.....
I will load the pictures of the pullies from my phone and post them up here in a bit,just got home from work.....4 mile walk in the dark and rain....this old man needs a beer...lol
Also I think a major part is the aftermarket battery terminal just sucks and may of not had a great connection,also found corrosion in it as well.
Tomorrow the fusable link thing that is attached to the terminal should be at dealership and hoping that is all that popped.We were able to test all functions of the car using this tool that hooks to the battery and supplies power to anything to see if it will work and so far everything worked,which is good because the fuse is only $16.50,hoping it is all that blew,I have bad luck at times....but it is a car and cars tend to Gremlin.....
I will load the pictures of the pullies from my phone and post them up here in a bit,just got home from work.....4 mile walk in the dark and rain....this old man needs a beer...lol
Here is pictures of the pullies,I am waiting to do the crank pully for when Garm gets his in stock.....
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
All in all the install took less than an hour,used an impact gun to pull the alternator pully,the waterpump pully you just use a screwdriver or in my case a socket extension and stick it in the pully holes and undo the 3 bolts.
To pull the alternator bolt holding it to the motor you have to undo the fastner screw for the AC line and move it slightly out of the way to get bolt out to pull alternator.Used 22mm impact socket and impact gun to pull pully,it once the nut is off just pulls off with your hand,no puller needed.
LIke I said I think just sheer dumb luck I blew the fuse,going to pull the aftermarket terminal and put stock on back on and get a ring for the 0/1 amp wire and mount it to the stock terminal.Pully install on a scale of 1-10 I would say is a 3 tops,very easy to do as long as you have a buddy with an impact gun.Another option would be a 22mm offset box wrench and then hold the shaft with think it was 12mm and it also will come right off.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
All in all the install took less than an hour,used an impact gun to pull the alternator pully,the waterpump pully you just use a screwdriver or in my case a socket extension and stick it in the pully holes and undo the 3 bolts.
To pull the alternator bolt holding it to the motor you have to undo the fastner screw for the AC line and move it slightly out of the way to get bolt out to pull alternator.Used 22mm impact socket and impact gun to pull pully,it once the nut is off just pulls off with your hand,no puller needed.
LIke I said I think just sheer dumb luck I blew the fuse,going to pull the aftermarket terminal and put stock on back on and get a ring for the 0/1 amp wire and mount it to the stock terminal.Pully install on a scale of 1-10 I would say is a 3 tops,very easy to do as long as you have a buddy with an impact gun.Another option would be a 22mm offset box wrench and then hold the shaft with think it was 12mm and it also will come right off.