Replies continued
bzinn 1Thread starterUniversity Place,WA · Jan 18, 2012#201mr_milesPortland, OR · Jan 18, 2012#202oh cool, I'll be there :)
bzinn 1Thread starterUniversity Place,WA · Feb 2, 2012#203Well the next things to go in once the sun decides to come out and warm up to at least 50 degrees out is the '12 STI front bumper vents and a 22" wide 16 gauge 4 fin aluminum rear diffuser.
Gonna have to modify the diffuser to fit because the flowmaster is gonna be in the way.
I did end up going with a nice Boso pipe and to be honest it sounds like a moose mating call at high RPMs....I knew it would but I can fix it with some decent resonators in the midpipe.
Pictures this weekend of the car once it gets a bath.
Trying to get the money straight for Airride but my mom got really sick with kidney failure and everything has been put on hold for a bit.
CtrlAltDefeatIndianapolis IN · Feb 2, 2012#204sorry to hear about your mom... hope she is ok.
bzinn 1Thread starterUniversity Place,WA · Feb 3, 2012#205Thanks man....
She worries me,she has been pretty sick my whole life but it gets worse as she gets older and you only get one mom....
she went back to work today just so she can pay her bills.....sad that a person cant even get a bit of time off to try to get better.
STill gonna have to have surgury to remove the kidney and then dialisis will of course begin.
Hoping she can retire here by summer and just enjoy life a little.
bzinn 1Thread starterUniversity Place,WA · Feb 4, 2012#206Got some pictures of the STI bumper vents install today....was sunny and warm.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
ilikericesavannah, ga · Feb 5, 2012#207I like this idea alot.. I was gonna say "Should they be the other away around?". I searched before I typed, but you are correct. Thats the way the STI's have them. *shrugs*
I think I would be doing this also with my yaris and flip them, this is a good way to make a duct for cooling off brake rotors or for CAI.
Looks awesome.. I likes
TOUGEghostKauai · Feb 5, 2012#208Car looks good. I like the way the boso pipe came out. 👍
bzinn 1Thread starterUniversity Place,WA · Feb 6, 2012#209I still have to pull the bumper and do some back cutting on the passenger one to get the bottom a bit more flush and round up some washers that will fit the rivits and redo them so it has a better solid anchor on the back.
I would not recomend this type of mod to anyone if your not sure about your ability's.....they are big holes and it took like 3 hours to get them both aligned together.
Also with the lip kit,the canards and the vents now the front end is pretty busy when you look at it head on but it all in all came out fairly good.
My rear diffuser came in the mail tonight but I got home too late and the apt manager where the post man left it was already gone for the day.If the good weather holds I will begin the install on it on Saturday.
bzinn 1Thread starterUniversity Place,WA · Feb 8, 2012#210bzinn 1Thread starterUniversity Place,WA · Feb 8, 2012#211Pictures Saturday of the Rear Diffuser install.....I have to trim the thing down on one side a couple of inches to fit around the Flowmaster.
bzinn 1Thread starterUniversity Place,WA · Feb 12, 2012#212Couple of pictures of the rear diffuser.....took me about 4 hours total labor and 7 beers....had I slowed on the beers probably would of taken 2 hours lol
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Made out of 16 gauge aluminum and then powdercoated
malibuguyWestminster, MD · Feb 12, 2012#213The bozuko (or w/e) pipe is stupid. The rest i like
SpidermandudJohnson City, Tennessee · Feb 12, 2012#214Driven it with the diffuser on/ notice any difference?
bzinn 1Thread starterUniversity Place,WA · Feb 12, 2012#215The only differance I notice today on the highway was it was quieter on the back of the car. Before the road noise from the tires and wind were more noticable even with the sound deadening,but now it is gone almost completely.
Yes I know the Bozozuku pipe is not for everyone....lol.....your not alone bro on not liking it....but I do appreciate the honestly.
If people did not try differant things and like differant things life would be boring.
ilikericesavannah, ga · Feb 13, 2012#216I his idea with my rear bumper also.. can you get some shots under their where you mounted it at?
bzinn 1Thread starterUniversity Place,WA · Feb 13, 2012#217I can take some more shots tomorrow since I gotta work swing shift.
I made out of angle aluminum two 5.5" brackets and mounted them through the floor with a bolt. The middle bolt is right in front of the carbon cannister,think that is what the black box is???? and the drivers side mounts about 8" over,there was a third mount but I cut that part off for the Flowmaster.
I am pretty sure that a canister exhaust would fit right beside this no problems as I only had to cut off 3.75 by like 12" piece to go around the exhaust.
The bumper edge was 3 bolts that went through bottom edge of the bumper.
I will get more shots tomorrow of it from underneath for ya.
I got it on Ebay under Universal Diffuser and it was the listing from think it was Neiland,WA and was $89 and shipping.It is well made,came with stainless hardware. The center two fins can be removed and are in there with built in threaded holes.....the aluminum mounts came from 1" angle piece from home depot cost was like $6.
My hardest part was the sub box was hard to work around,it is rivited to the floor and bolted so it is not gonna come out without several hours work...lol
bzinn 1Thread starterUniversity Place,WA · Feb 14, 2012#218Her is a few more pictures of the diffuser....was pouring rain so did not crawl under to take good picture of the mounts but you can see the driver side mount in the pictures.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
CtrlAltDefeatIndianapolis IN · Feb 15, 2012#219... I have to ask... is there a hole in the bottom of your exhaust pipe to let the rain drain out? lol
bzinn 1Thread starterUniversity Place,WA · Feb 16, 2012#220LOL....yep there is a hole in the main pipe that the stainless tip is welded to and also one in the low end of the stainless tip as well.
the first few days I had it on it would fill up with a good 6" of water since it just had to pour down rain that next day for like a week solid....it sucked,the pipe inside is grungy and gonna need shop vac attention.
ilikericesavannah, ga · Feb 16, 2012#221awesome, thanks for those pics. I like how you made those brackets. Love it.
SpidermandudJohnson City, Tennessee · Feb 16, 2012#222That's awesome. I didn't think it would yield sound deadening. Ballin.
bzinn 1Thread starterUniversity Place,WA · Feb 16, 2012#223Thanks guys....so far it has been solid but every so often on freeway...My only thing I do not like so far is every so often I get a shimmy in the rear.....I think I am catching some air under the top of it or something.....the car does whip around anyway with the kit and rear fin anyway on freeway the canards pushed the front down and I could feel that but diffuser is in traffic giving me a almost whip like you get when you run camber in the rain....i got no camber...
Gonna make another plate to cut any air going under I think and see how that does.
bzinn 1Thread starterUniversity Place,WA · Feb 16, 2012#224Another thing...sorry.
I also found that I need to isolate the mounts with a rubber washer where they meet the floor....why...when the sub is on it seems to move the sound wave through anything not dampened with a rubber washer....like the body panels...hatch....liscense plate....
But this is the whole diffuser making a rattle to the sub....lol...it sucks...I will fix it.
Rattles suck
bzinn 1Thread starterUniversity Place,WA · Mar 1, 2012#225Very stoked.....my buddy is having a photoshoot for his site 206factory in April and is gonna hook me up with the model to do photoshoot in my car and model the Takata's.....buck ass naked..........I am kinda in heaven right now.....a dream come true....hot naked chick in my car....
mr_milesPortland, OR · Mar 2, 2012#226When and where? I'll drive up with my gf lol
bzinn 1Thread starterUniversity Place,WA · Mar 8, 2012#227So far the rear diffuser has been solid,finally did a full tank of gas and no loss of milage,no gains either though...lol
Here is a picture of the rear floor pieces the two small ones are carbon fiber solid sheet in the middle and wood trim rings coated like the sub box and pods in bedliner....The small ones will hold the compressors next to the sub box and the long one will hold the air tank
Picture not included in this copy
bzinn 1Thread starterUniversity Place,WA · Mar 9, 2012#228Ordered a roll of CF vinyl 48" x 120"....jesus.....that was expensive....it better be enough to complete interior parts I want done...
bzinn 1Thread starterUniversity Place,WA · Mar 14, 2012#229CF Vinyl came today,so I pulled the A pillars out and gave it a try,was much harder than I thought it would be.Main reason was it really needs heat to make it work and stretch.
I ruined the first attempt so I waited for my kid to get home and put him on hair dryer duty.
Took about 90 min to do the first pillar,then about 30 min to match up to the second pillar the pattern....was not easy.....had to make sure the two patterns matched in direction and tilt....
I will take pictures tomorrow once I get some daylight.Total time to do A pillars was little over 4 hours including putting the tweeters back in them.
I am in the middle of moving to a new house so that is probably as far as I will get till after the first unless I get a nice sunny day to do the rest of interior.
bzinn 1Thread starterUniversity Place,WA · Mar 15, 2012#230Got a couple of night shots to not be too bad with the droid.....
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
SpidermandudJohnson City, Tennessee · Mar 15, 2012#231Man I love seeing you update this thread. That CF looks really nice in there. You get the rear floor pieces in there?
bzinn 1Thread starterUniversity Place,WA · Mar 15, 2012#232Been busy prepping for move to the new house on the 1st so everything has been kinda in limbo.
I gotta build an aluminum frame for the amp to mount to,moving it from the rear seat frame to a bit further back and the airtank floor will be suspended over it,still gotta work out those logistics...lol
I have to say that the CF vinyl although not hard to work with was definatly a two person job to have someone working the hair dryer is a must to get it to stretch cleanly.
I promise shortly after the 1st to have the CF all in adn good pictures....still wont have the airride in till June it looks...I am building an interior for my buddie and for doing it I get free pair of 400cc compressors and most likely he is selling me one of his air tanks for cheap as he is putting in a diffeerant setup in his xB
It has been an amazing build for me to see how the car has evolved,I stuck fairly close to my original list of thinks to mod...I hope by summers end to have the car mostly complete and then probably enjoy it as is for a while and then figure out some paint.
Big items on list are airride.....interior complete....and camber 1.5 in front and 3 in back.
bzinn 1Thread starterUniversity Place,WA · Apr 10, 2012#2336 of 10 interior pieces CF Vinyl wrapped....still got doors where the cloth is at the top but have to pull my components out and the Xovers off to pull the panels,waiting for a nice sunny day off.
STill have the C pannel on passenger side and the grey panel under the passenger rear side window to go along with the doors...so far so good as long as I do not run out short as I screwed up one A pillar and that ate a bunch of material to redo it right.
Got new house to a very livable start,got some flower beds dug this weekend and the yards mowed.....
Did find a nice huge Oak office desk and a sofa in the back shed in great condition....lol
Well this saturday I will post up some pictures of the interior so far....I cant work on it this week as I am doing two other jobs that I have to complete to get paid....
bzinn 1Thread starterUniversity Place,WA · Jun 13, 2012#234Sorry I got a bit sidetracked with new house and my Mom's health....which is doing much better but she retired finally and is living at my house....she is a cool Mom so for me it is nice to have her around.
Car is in pieces in the inside right now,spent some hours smoothing out panels in side and prepping for paint.
Saturday I will finish the prep and have ready for painting the pieces....the CF vinyl was a pain and I gave up and pulled it all out.
I will post up pictures on Saturday
bzinn 1Thread starterUniversity Place,WA · Jun 24, 2012#235finally got some pictures......super busy but managed to get a first coat of icing on the steering column and some primer and paint....not the final color but something to see none the less...lol
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
bzinn 1Thread starterUniversity Place,WA · Sep 23, 2013#236hello everyone...yes I have been gone for a while...still rolling the yaris...
Well it is nearly complete...this year I found out I had a huge 401k....well not huge but $5000 in 401k that I had no idea I even had so after penalties and taxes I got $3800....so paid of the car....paid off 2 $900 credit cards...and bought airride system for car...it is due here any day now...still have the rear bags and perches to buy and fittings and lines...$350...
Car is now rhinolinered on all parts that I glassed adn bondoed last year and came out sick...includes headliner...huge sound dampening effect...
rear false floor is built and amp mounted...platforms for chrome tank and compressors made and CF plates for them made and mounted...just awaiting parts....
painted centers of Axis OGs blue and stripped clear off lips and polished...way better...car going satin paint next year...
still got a few interior pieces to glass and paint and a huge pile of LEDs to install inside and under the hood...it is dark and grey out here in PNW for next 7 months so lights are the fun thing to do over a winter...
got back to work...working for Goodwill Industries as a building maintenance worker...make just a small bit less an hour but got 6 more paid holidays and 1 more paid sick day....so it is a win...and it is a stress free job....and company phone and vehichal...dont miss Sears at all...nearly lost house and car this year but made it through....I will in a month post up pictures of build...these will be the enarly finished pics casue there is not much left to do...
Gonna buy a toyota truck...an old one and use it to daily drive...and build it for fun while drivetrane gets built in yaris....not as extreme as Garms...I wish...but enough to let them know it is fast enough to smoke them
stay safe this Winter guys...took 5 long years and went through hell and back and still building the car...
yarisugiハワイ · Sep 24, 2013#237Whoa... almost like that guy who slept under a tree for forty years!
Welcome back. Need to see what type of air ride you got along with... MOAR PICS!!
bzinn 1Thread starterUniversity Place,WA · Oct 31, 2013#238Sorry been gone so long...uploading pictures to photobucket now...give me a minute and I will post them
bzinn 1Thread starterUniversity Place,WA · Oct 31, 2013#239bzinn 1Thread starterUniversity Place,WA · Oct 31, 2013#240As you can see my plan for interior changed a lot over the course of a year...all of the interior parts that were glassed were changed from being painted to being Rhino Linered...durable,and provides a bit of sound deadening....
My sub blew a coil wire,should be able to have it resoldered but had a backup that I installed and honestly it is close to as loud and clear..does not hit as hard but still hits very hard...
The setup is Universal Air
dual Viare 480 compressors
chrome 5 gallon tank
Yaris/xD rear bags mount
Manual paddles
1/4 DOT line and push to connect fittings
Used a xD heat/cool panel to mount gauges under the steering wheel,still need to complete that install...for now it is zip tied in place
Had to notch the rear diffuser to make room for the Flowmaster which had to be pulled over 2" to center of car to give clearance for rear bag
Fronts will go lower if I remove the front sway bar...still debating...for now leaving it in as it does give me a failsafe should a i blow a front line it wont drop on tire and hinder turning.
Debating fenderflares and cutting fenders to allow a 25mm front spacer and a 25mm rear hub spacer...and push out the wheels a bit...still need to try some differant fitment wheels with like a 10 and 0 offset first to see how far out it goes to mock up how much to cut...would jsut change out wheels but I love these for now so spacers it may be first.
bzinn 1Thread starterUniversity Place,WA · Oct 31, 2013#241As to cost...I lost track....I know for certain I have $1850 in the bag setup alone...that does not include the wires,false floor,fuses,splitters for power block...that I would guess at around $200 more...then LEDs which will be installed soon I guess a good $150 plus I am getting an underglow setup from buddies xB to install as well.
door panels where they have the blue polkadots will be replaced soon with black headliner material
also used xD heater/cooling control knobs to replace the tonka toy looking ones car came with...that was another $35 but they came with the knob panel which is working perfedctly for holding the gauges
The ride...well it can ride a finger gap over the tires and does not rub...very stiff ride,close to coilover stiff.when low it is a little bouncy but that is fine
The MI hood fitment is dead on except the latch,took a file and 10 minutes and it works flawlessly....get one while he has them guys it is a nice hood and for the cost you cant go wrong.