KioshiOriginal postFremont, CA · Oct 13, 2009#1I'll be less discrete in here....
To answer your question from previous thread CTScott...
Cluster indicators working:
High beam
regular beam
fogs (i dont have)
driver seatbelt working
engine sign
no maintenance light
Temp cool and hot
Tach working
Cluster indicators and other indicators on car not working:
passenger seatbelt (the one near the right side center vents...)
passenger airbag (although, after i clicked the seatbelt w/ no passenger, it shows: Airbag off light, I haven't tried w/ passenger seated)
E-brake light on ((!))
NEW DISCOVERY....tonight i went out for a 2 mile drive....i noticed the speedometer DOESN'T work, 🤷???
Replies 123
KioshiThread starterFremont, CA · Oct 13, 2009#2Something just hit me.... Its a direct swap, BUT only for 08 Yaris models and up, because.....08 models started to have the S models which came with a tach (i believe)...so to accomodate the tach, the wiring had to be different setup on 08 basic models too. 07 models and below did not have S models or tachs. The wiring is different on 07 versus the 08....
Gideon on here had the cluster working perfectly (08' model), but my speedometer wont work on mine (07' model)
KM conversion to mph I'll get use to....just use my GPS as a reference guide for a few days, then i have it memorized lol.
I have to adjust the kms on the cluster to those miles on my current one...
EDIT: Anyone w/ an 08' base or S Yaris model...could you show me a close up shot of the two connectors that connect to the cluster? Or a diagram from the 08 S Owner's manual...?
KioshiThread starterFremont, CA · Oct 13, 2009#3The 08 S cluster, does that work on an 07 Yaris? A base no tach cluster will work on an 07... I've seen that....
Gideon's 08 base made the JDM cluster work plus his current one...i strongly think it has to do w/ wiring on the 07 versus 08 models....
GideonSunnyvale, CA · Oct 13, 2009#4Yeah, the cluster worked fine in my car.
Advocate and I took it in my car for a spin to verify it was all good, and as far as I was aware, it worked fine. I don't know about dimming, (it was bright, but I had my instrument lights on the highest setting as usual) but I recall that everything else was operational because I was taking note of my shift speed at redline to verify it was reporting speed correctly.
Also I recall pointing out that it was nice to have just one light on the cluster, which was my airbag light, (always on because of the driver seat removal) instead of two (TPMS light going off on my stock cluster, JDM doesn't have it AFAIK) so as far as I was aware, indicators worked fine. (Headlight, high beam light, etc)
KioshiThread starterFremont, CA · Oct 13, 2009#5Funny...the (SRS) airbag light stays ON in my car too...And i have stock seats haha. I want to see if a passenger sitting on the right side will make it go away. Nonetheless, the SRS light and brake light don't bother me or effect the car in any way.
I'll wait for you and CTScott tomorrow and conquer this piece~
CTScottUSA, CT · Oct 13, 2009#6USDM 07-09 wiring is identical, except for additional signals that were added with new features (none were moved though). The tach is not fed by signal wire on the cluster. The clusters with a tach actually get the tach data from the ECM via CAN bus.
The speedometer is fed off of the transmission speed sender unit on non-ABS cars, and via CAN bus from the Brake Actuator on ABS equipped cars.
Emergency Brake signal is sent over CAN bus, but brake fluid level is fed by direct signal.
Where wire swaps come into play is with RHD vs LHD cars, and there are some differences
with European (TMMF) vs Japanese (TMC) cars.
The EWD that I am referencing is a European one, which has the details for TMC and TMMF manufactured cars, ones with and without VSC, with and without automatic A/C, and with and without the entry and start system (push button start). I would really like to get my hands on a set of JDM EWDs to see if there are any differences from the one I am looking at.
CTScottUSA, CT · Oct 13, 2009#7Looking at Gideon's post about the Speedo, etc. working properly in his car; It really makes we wonder if your 07 ECM is the issue. For example, if Gideon has ABS and you don't, that could explain the speedo working in his but not on yours.
KioshiThread starterFremont, CA · Oct 13, 2009#8Then how come my ECM sends signal to the tach instead of the speedometer. whereas when I switch back to stock, the speedometer works.
Also, due to my stupidity, i drove to work w/ the JDM cluster.
Update 2: Aside from speed not working, the odo kilomters dont work either. It stayed at 60809 kilometers during my 3 mile commute to work...I hope this helps.
I would still like to see the wiring config on the 08'...something tells me in the back of my mind, that that can be the cause....lol..
And the cluster dims when holding the button 3 secs. Thanks for that help :)
Would pics of my connector with the wiring help CTScott?
I know the pins had to be taken out and rewired to make the JDM Vitz RS tail lights work correctly....i think this is the case here too?~
CTScottUSA, CT · Oct 13, 2009#9 Originally Posted by
Kioshi ↑ Then how come my ECM sends signal to the tach instead of the speedometer. whereas when I switch back to stock, the speedometer works.
Also, due to my stupidity, i drove to work w/ the JDM cluster.
Update 2: Aside from speed not working, the odo kilomters dont work either. It stayed at 60809 kilometers during my 3 mile commute to work...I hope this helps.
I would still like to see the wiring config on the 08'...something tells me in the back of my mind, that that can be the cause....lol..
And the cluster dims when holding the button 3 secs. Thanks for that help :)
Would pics of my connector with the wiring help CTScott?
I know the pins had to be taken out and rewired to make the JDM Vitz RS tail lights work correctly....i think this is the case here too?~
I have the USDM EWDs for 07, 08 and 09, so I am sure its not a pin difference thing between the two USDM cars. I just triple checked the USDM ones and the only difference wiring-wise between the three years is the addition of TPWS to pin 6 of the right side connector, everything else is identical.
As for the speedometer issue, My theory is if you don't have ABS, then you have a different ECM than a car with ABS (or at least for 07). The ECM would be programmed to send speed data to the cluster on an non-ABS ECM, whereas on a ABS car it would be programmed to not send it, as the meter would get it from the Brake actuator.
So, why have people been able to swap USDM clusters? Well, maybe it was only 07 USDM ECMs that didn't send the speedo data to the cluster, as maybe ABS was atypical in 07. Then, in 08 the ECM would send it whether it needed to or not. (Again, just me speculating)
Your odo not working makes sense if the speedo isn't working, as the odo is based on the speedo.
CTScottUSA, CT · Oct 13, 2009#10Oh, and as for the tach working, the tach was always CAN based. It didn't have two different feeds like the speedo.
KioshiThread starterFremont, CA · Oct 13, 2009#11I see. Would there be any solution to this, lets say if I installed ABS on my 07..?I think there was an option to do, not quite sure..
Now what really has me sparked is....if i took Gideon's or anyone else's 08 base cluster ( with speedometer only) and tried it on mine..would it work? Since you said 08 ECM sends signal through Brake Actuator..and the 07 sends through transmission speed sensor. And I'd like to see if thats the case~
This is a CVT cluster from the RS. It works flawlessly with my manual tranny, the gears are accordingly done. I took 3rd to 6000rpm, no flaw what so ever..
EDIT: Just read your post about the tach working through the CAN....
CTScottUSA, CT · Oct 13, 2009#12 Originally Posted by
Kioshi ↑ I see. Would there be any solution to this, lets say if I installed ABS on my 07..?I think there was an option to do, not quite sure..
Now what really has me sparked is....if i took Gideon's or anyone else's 08 base cluster ( with speedometer only) and tried it on mine..would it work? Since you said 08 ECM sends signal through Brake Actuator..and the 07 sends through transmission speed sensor. And I'd like to see if thats the case~
This is a CVT cluster from the RS. It works flawlessly with my manual tranny, the gears are accordingly done. I took 3rd to 6000rpm, no flaw what so ever..
EDIT: Just read your post about the tach working through the CAN....
I am thinking that the simplest solution to the speedo issue may be to pick up a newer ECM.
I am very curious as well about trying a newer USDM cluster (ABS equipped) on your 07.
KioshiThread starterFremont, CA · Oct 13, 2009#13I'm totally an idiot when it comes to these things...
Could you obtain the ECM part number by any chance?
And is it something a dealer will only do or can i have tuner shops do this as well?
I will have to arrange w/ Gideon or anyone else in the Bay Area to let me swap out for 5 mins to try the 08+ base cluster..
Advocate, fmicle, ezhacker, can one of you be nice enough to let me do that for 5 mins? 😳 I will buy the person lunch (seriously)...
CTScottUSA, CT · Oct 13, 2009#14 Originally Posted by
Kioshi ↑ I'm totally an idiot when it comes to these things...
Could you obtain the ECM part number by any chance?
And is it something a dealer will only do or can i have tuner shops do this as well?
I will have to arrange w/ Gideon or anyone else in the Bay Area to let me swap out for 5 mins to try the 08+ base cluster..anyone nice enough to let me do that for 5 mins? 😳
I would try the cluster swap test first. If the speedo doesn't work, then I'd start looking for an ebay or junkyard ECM that is off of an 08 with the same type of transmission. Ideally, you'd want to first try the cluster in someone's 08 that doesn't have ABS. (Or, if Gideon doesn't, then that's already been done.)
WolfWingsKansas City, MO, USA · Oct 13, 2009#15I'll try to grab my friend's 09 cluster (with ABS) and slap it into my 07 Yaris Liftback (without ABS) and verify the speedo works or not, nothing is a substiture for a live-fire test, ya' know?
May not get it done this week, but I'll try just to rule that in/out.
KioshiThread starterFremont, CA · Oct 13, 2009#16WolfWing - That would be GREATLY appreciated if you could test that out for me. And true that, for a live-fire test 🙂
Also, thanks for the dimmer tip....it worked. When my lights were on, they toggled to dim and then back to bright when lights off..Keep us updated~
CTScott - I just texted Gideon, he has ABS on his. So...i will try to find someone to test out JDM cluster on a non-ABS 08' model...With WolfWing's test results and mine after swapping the clusters from our friends, i hope it will provide you with more concrete solution...
I know Kragen Auto Parts can order refurbished car parts for almost any model...can they order ECM too? I may order it through them instead of ebay or junkyard..
P.S. What does ECM actually stand for? (electronic control management?)
Sorry for asking this so late in this problem...😆
CTScottUSA, CT · Oct 13, 2009#17 Originally Posted by
Kioshi ↑ WolfWing - That would be GREATLY appreciated if you could test that out for me. And true that, for a live-fire test 🙂
Also, thanks for the dimmer tip....it worked. When my lights were on, they toggled to dim and then back to bright when lights off..Keep us updated~
CTScott - I just texted Gideon, he has ABS on his. So...i will try to find someone to test out JDM cluster on a non-ABS 08' model...With WolfWing's test results and mine after swapping the clusters from our friends, i hope it will provide you with more concrete solution...
I know Kragen Auto Parts can order refurbished car parts for almost any model...can they order ECM too? I may order it through them instead of ebay or junkyard..
P.S. What does ECM actually stand for? (electronic control management?)
Sorry for asking this so late in this problem...😆
The ECM (engine control module) is also know as the ECU (engine control unit). If you shop around ebay and junkyards (
www.car-parts.com is a national registry of junk yard parts), you can sometimes find them for $50 or less. I missed out on an ebay one for $34.99, when I was looking for one to run on my test bench (Garm loaned me his and I actually have it running one my desk with a bunch of simulated sensor feed circuits for my YarGauge development).
Typically when people sell them they either list the vehicle's VIN and/or what year/features it had (3dr, 5dr or sedan, transmission type, ABS, etc.)
KioshiThread starterFremont, CA · Oct 13, 2009#18I wanted to say if it was similar to ECU or that actually..but thanks for clarifying CTScott. And very much appreciated for the link. I will look on that for the 08 ECU after cluster tests....
I dont mind spending another $100 on making this cluster work.
I know Toyota wont install an 08 ECU on an 07...so best possible place to get this done?
I just checked that link out Scott, no ECU on there in the list for the Yaris...I'll check ebay mostly as i dont think i have time to go to junkyards and look for one...
GideonSunnyvale, CA · Oct 13, 2009#19Yeah Kioshi there are tons of ECUs on eBay for about $150.
Although I found this one interesting:
Picture lost · img515.imageshack.us
KioshiThread starterFremont, CA · Oct 13, 2009#20^^^^Wow.....
Lots of 2007 ECUs on there..I'll keep looking for an 08 manual tranny LB ecu..
If you guys happen to find them before me, post the link on here kindly
CTScottUSA, CT · Oct 13, 2009#21 Originally Posted by
Kioshi ↑ I wanted to say if it was similar to ECU or that actually..but thanks for clarifying CTScott. And very much appreciated for the link. I will look on that for the 08 ECU after cluster tests....
I dont mind spending another $100 on making this cluster work.
I know Toyota wont install an 08 ECU on an 07...so best possible place to get this done?
I just checked that link out Scott, no ECU on there in the list for the Yaris...I'll check ebay mostly as i dont think i have time to go to junkyards and look for one...
Best place is right in your driveway. 4 screws and 2 connectors and your done.
CTScottUSA, CT · Oct 13, 2009#22 Originally Posted by
Gideon ↑ Yeah Kioshi there are tons of ECUs on eBay for about $150.
Although I found this one interesting:
Picture lost · img515.imageshack.us
That's for a 1st gen Vitz.
GideonSunnyvale, CA · Oct 13, 2009#23Damn, I thought it looked different than our ECU too. Boo.
KioshiThread starterFremont, CA · Oct 13, 2009#24I did search for a DIY on swapping ECUs...and found this thread -
instrument cluster-TACH "S" model Mike aka mikenacarato says all 09' are equipped w/ ABS, have to find out if all 08's were ABS as well.....
CTScott - this is the location of the ECU i have to swap for an 08 one right?
Attached picture not available Sedan and hatchback share the same ECU? or should i get a hatchback one specifically?
Do i have to remove the whole dash, looks to be that way to get to the 4 screws....
mr9865Green Bay WI · Oct 13, 2009#25not all 08s had abs
CTScottUSA, CT · Oct 13, 2009#26That's the main body ECU (which handles things like door locks on a so equipped car). The ECM is the silver box under the hood against the firewall on the left side (with the two big black connectors).
KioshiThread starterFremont, CA · Oct 13, 2009#27So I would need to be looking for Engine ECM/ECU, correct?
Are there reports of anyone having done this in the past, compatible....? CTScott, you have an Garm's ECU..is it identical to the 09's?
Going to small junkyard next week..
CTScottUSA, CT · Oct 14, 2009#28 Originally Posted by
Kioshi ↑ So I would need to be looking for Engine ECM/ECU, correct?
Are there reports of anyone having done this in the past, compatible....? CTScott, you have an Garm's ECU..is it identical to the 09's?
Going to small junkyard next week..
Correct on what you are looking for.
The 06-09 ECMs all look identical, but there are different part numbers on them depending on the features of the car they are used on.
KioshiThread starterFremont, CA · Oct 14, 2009#29Now from what you've told me, the main features the Engine ECM needs to hold is: Manual tranny, liftback, and ABS?
Would a sedan ECU make a difference, or does it have to be liftback? Lots of sedan ECUs on ebay......
CTScottUSA, CT · Oct 14, 2009#30 Originally Posted by
Kioshi ↑ Now from what you've told me, the main features the Engine ECM needs to hold is: Manual tranny, liftback, and ABS?
Would a sedan ECU make a difference, or does it have to be liftback? Lots of sedan ECUs on ebay......
Actually, if Gideon's car is non-ABS and the speedo worked, then you want a non-ABS one. If you put an ABS one in your car, it still may not work, since you don't have the Brake Actuator to send the speed info to the cluster.
I believe that a sedan ECM would be fine in a LB.
KioshiThread starterFremont, CA · Oct 14, 2009#31CTScott, Gideon confirmed to me that his car had ABS in it. Installing an ABS enabled ECM would enable to send speed info through brake actuator then for me? Or would i need to hunt down a brake actuator as well?
Ok, I'll dig up on sedan ECMs as well now...
CTScottUSA, CT · Oct 14, 2009#32 Originally Posted by
Kioshi ↑ CTScott, Gideon confirmed to me that his car had ABS in it. Installing an ABS enabled ECM would enable to send speed info through brake actuator then for me? Or would i need to hunt down a brake actuator as well?
Ok, I'll dig up on sedan ECMs as well now...
You don't have ABS, so you don't have the brake actuator.
I really think that before you spend money on an ECM, that you should test it on an 08 with no ABS.
KioshiThread starterFremont, CA · Oct 14, 2009#33I'll go ahead and do that. But chances of finding someone with an 08 without ABS is slim to none, at least for me in California.. :(
I called my Toyota dealership today and they said they cannot install ABS on my car. Supposedly it comes from the factory installed... So I'm shit out of luck if ABS is required CTScott....
Update 3: SO i had a passenger sitting in my car and the airbag light indicator near the right side vent DOES turn on, but seatbelt indicator does NOT...thats fine for me...no more beep noise~
Do you know of anyone around you w/ an 08 non-ABS yaris lb CTScott? I could ship it out to you, me paying the expenses both ways...
CTScottUSA, CT · Oct 14, 2009#34 Originally Posted by
Kioshi ↑ I'll go ahead and do that. But chances of finding someone with an 08 without ABS is slim to none, at least for me in California.. :(
I called my Toyota dealership today and they said they cannot install ABS on my car. Supposedly it comes from the factory installed... So I'm shit out of luck if ABS is required CTScott....
Update 3: SO i had a passenger sitting in my car and the airbag light indicator near the right side vent DOES turn on, but seatbelt indicator does NOT...thats fine for me...no more beep noise~
Do you know of anyone around you w/ an 08 non-ABS yaris lb CTScott? I could ship it out to you, me paying the expenses both ways...
Actually, Crashy is an 08 non-ABS LB.
KioshiThread starterFremont, CA · Oct 14, 2009#35 Originally Posted by
CTScott ↑ Actually, Crashy is an 08 non-ABS LB.
Is it still functional, to drive a few mph at least? Sorry I haven't been reading the thread 🙁
If so, would you do the honors?
CTScottUSA, CT · Oct 14, 2009#36 Originally Posted by
Kioshi ↑ Is it still functional, to drive a few mph at least? Sorry I haven't been reading the thread 🙁
If so, would you do the honors?
She's fully drivable (not road legal, but still she can cruise).
She'd be a perfect test platform. And, if it doesn't work on her, I can try it on my 09 while sniffing the CAN bus to see if I can figure out a way to make it work. Thanks to my YarGauge development project I now have a fully functional homemade CAN bus sniffer.
I'll PM you my shipping address.
Sir A.Y. AtoyotSurrey, BC Canada · Oct 14, 2009#37 Originally Posted by
CTScott ↑ That's the main body ECU (which handles things like door locks on a so equipped car). The ECM is the silver box under the hood against the firewall on the left side (with the two big black connectors).
Left side? I thought that the reference for the left and right sides of the car were the driver's left and right hands when seated behind the wheel. For example, on North American cars, the steering wheel is on the left side. The ECU is on the right side. Or am I wrong?
KioshiThread starterFremont, CA · Oct 14, 2009#38Lets hope it works on Crashy.
That be really nice if you could figure out to make it work on an 07 Yaris LB if the latter doesn't work.
Actually I have a gap in my schedule to ship out tomorrow, first thing in the morning. You should get it by Monday at the latest....
Thank you Scott.
Sir A.Y. Atoyot - i think CTScott meant from the perspective of looking at your engine bay standing in front of it. It is on the right from that view..
CTScottUSA, CT · Oct 14, 2009#39Correct. I was thinking of your right or left as you are standing there with the hood open.
advocatelocation · Oct 15, 2009#40Friday Kioshi. But you don't need to buy me Lunch =)
I'll be on the 5th floor of the 7th garage parked near the stairs down. Although you'll beat me there you should park up there first.
For reference my car has 0 packages. It's completely bare bones.
Edit: Just saw you're about to ship it to CTScott. Texting you now just because we might as well try it in my car to make sure that it didn't just break or something. Might as well give it a shot before you send it off for a week or two.
KioshiThread starterFremont, CA · Oct 17, 2009#41The cluster is in CTScott's hands now.
advocate - my moron brother mailed it earlier...
Now the fun begins....
CTScottUSA, CT · Oct 17, 2009#42 Originally Posted by
Kioshi ↑ The cluster is in CTScott's hands now.
advocate - my moron brother mailed it earlier...
Now the fun begins....
It arrived late this afternoon. I will give it a try in the morning.
KioshiThread starterFremont, CA · Oct 17, 2009#43hope it was packed good enough...
Ok, cool.
CTScottUSA, CT · Oct 17, 2009#44 Originally Posted by
Kioshi ↑ hope it was packed good enough...
Ok, cool.
It was well packed. I hooked it up as soon as I got home tonight, but unfortunately with Crashy not having any lights, it was too dark to take it for a spin.
CTScottUSA, CT · Oct 18, 2009#45I just tested it on Crashy, and the speedometer doesn't work either. She is an 08, with an automatic transmission and no ABS. The gear indicator does work, as you can see in the video below.
http://s372.photobucket.com/albums/o...r-Nospeedo.flv So, now to figure out how to make it work.
KioshiThread starterFremont, CA · Oct 18, 2009#46strange...maybe your assumption of it needing ABS could be true....
fingers crossed that the CAN bus can tell you how to bypass the ABS...
CTScottUSA, CT · Oct 19, 2009#47 Originally Posted by
Kioshi ↑ strange...maybe your assumption of it needing ABS could be true....
fingers crossed that the CAN bus can tell you how to bypass the ABS...
My CAN bus sniffer is proving very helpful. Last night I isolated all of the CAN bus message ID's (about 24 distinct ones on Crashy, who's an 08) to specific CAN devices. This requires unplugging all of the CAN devices except the ECM, and then plugging them in one at a time and sniffing the BUS.
I then sniffed my 09 (who has ABS) and found 12 additional message IDs. I haven't isolated the 09 ones to specific devices yet, as the devices are no where near as accessible as they are on Crashy. One of the new ones that I found on the 09 corresponds with one that someone doing CAN development on the Prius figured out to be the broadcast message of the vehicle speed.
So, hopefully tonight I'll have time to run my 09 on stands while sniffing the "speed" message to see if it does correspond.
KioshiThread starterFremont, CA · Oct 19, 2009#48 Originally Posted by
CTScott ↑ My CAN bus sniffer is proving very helpful. Last night I isolated all of the CAN bus message ID's (about 24 distinct ones on Crashy, who's an 08) to specific CAN devices. This requires unplugging all of the CAN devices except the ECM, and then plugging them in one at a time and sniffing the BUS.
I then sniffed my 09 (who has ABS) and found 12 additional message IDs. I haven't isolated the 09 ones to specific devices yet, as the devices are no where near as accessible as they are on Crashy. One of the new ones that I found on the 09 corresponds with one that someone doing CAN development on the Prius figured out to be the broadcast message of the vehicle speed.
So, hopefully tonight I'll have time to run my 09 on stands while sniffing the "speed" message to see if it does correspond.
If the 09 corresponds to the Prius broadcast message of the vehicle speed, what would that mean?
Isn't the speed some how related to the mpg meter on the Prius. I know on the older models depending on what speed you were cruising at, it corresponded to the mpg you would be getting....
CTScottUSA, CT · Oct 19, 2009#49 Originally Posted by
Kioshi ↑ If the 09 corresponds to the Prius broadcast message of the vehicle speed, what would that mean?
Isn't the speed some how related to the mpg meter on the Prius. I know on the older models depending on what speed you were cruising at, it corresponded to the mpg you would be getting....
The ECM gets the speed info and then broadcasts it over the CAN for whomever needs it (power steering ECU, etc.). The only significance to the Prius is that someone figured out that particular message. Other than the standard OBD protocol over CAN, there is little to no information out there, so it typically takes lot of work to figure out what data the messages contain.
KioshiThread starterFremont, CA · Oct 19, 2009#50 Originally Posted by
CTScott ↑ The ECM gets the speed info and then broadcasts it over the CAN for whomever needs it (power steering ECU, etc.). The only significance to the Prius is that someone figured out that particular message. Other than the standard OBD protocol over CAN, there is little to no information out there, so it typically takes lot of work to figure out what data the messages contain.
Oh, i see, that would make it easy then. Hope it matches up to the Prius's code, seeing that they both use the 1.5 liter engine...
This cluster just went from being interesting to complicated in my head now...lol