Replies continued
CTScottUSA, CT · Oct 19, 2009#51 Originally Posted by
Kioshi ↑ Oh, i see, that would make it easy then. Hope it matches up to the Prius's code, seeing that they both use the 1.5 liter engine...
This cluster just went from being interesting to complicated in my head now...lol
It is looking like the two possible solutions for it may be:
1. Install an ABS equipped ECM (but then the question is if you have an ABS ECM without actually having ABS will there be any issues).
2. Build a device that simulates the broadcasting of the speed data. This one sounds crazy, but is actually not that bad. With my YarGauge development work, I have a reference design that I can use. I can already read the speed from the ECM, so I just need to repackage that data into the correct message for the cluster.
Provided that I can figure out the CAN messaging for speed (or that the Prius message ID is the same and therefore I already have), then this is actually fairly simple. And, the hardware that I am using is not too expensive, so I should be able to provide a packaged solution for about $30.
CTScottUSA, CT · Oct 19, 2009#52 Originally Posted by kustom play ↑
sounds like a lot of work
looks like it would of been better just to get the USDM cluter, its a bit more but at least everything will read out in MPH rather then KM.
I would buy a car with a swapped cluster that was in KM
It's definitely not a trivial swap, but the USDM ones with a tach seem to be pretty hard to come by.
Now that you mention the km issue, I realized that I can do the conversion in the data sent to the cluster so that 100 kmh = 100 MPH.
advocatelocation · Oct 19, 2009#53 Originally Posted by
CTScott ↑ It's definitely not a trivial swap, but the USDM ones with a tach seem to be pretty hard to come by.
Now that you mention the km issue, I realized that I can do the conversion in the data sent to the cluster so that 100 kmh = 100 MPH.
Jesus Scott now THAT'S impressive 🙇
I'm loving this thread!
KioshiThread starterFremont, CA · Oct 19, 2009#54 Originally Posted by
CTScott ↑ It is looking like the two possible solutions for it may be:
1. Install an ABS equipped ECM (but then the question is if you have an ABS ECM without actually having ABS will there be any issues).
2. Build a device that simulates the broadcasting of the speed data. This one sounds crazy, but is actually not that bad. With my YarGauge development work, I have a reference design that I can use. I can already read the speed from the ECM, so I just need to repackage that data into the correct message for the cluster.
Provided that I can figure out the CAN messaging for speed (or that the Prius message ID is the same and therefore I already have), then this is actually fairly simple. And, the hardware that I am using is not too expensive, so I should be able to provide a packaged solution for about $30.
For solution 1, I would have to ask Gideon if he could volunteer for an ECM swap to try that out....(very low possibility of happening, i think)
CTScott, if you could construct a device that broadcasts the speed data, I'd be willing to take that chance and option MORE than a ECM w/ ABS running on a car without an ABS system. I'd rather not have problems down the road w/ an ECM enabled for something and the actual car not having it at all.
CTScott, I'm willing to put down an extra $100+ towards your R&D work (seriously, just ask Gideon) to make the cluster work....
I'm keeping fingers crossed its the same message data from the Prius.
Converting 100 kmh to actual 100 mph? As awesome as it sounds, wouldn't the speed limiter have to be set to 120 kmh then, I dont think the car can handle going 180 kmh ~ 180 mph.....?
CTScottUSA, CT · Oct 19, 2009#55 Originally Posted by
Kioshi ↑ For solution 1, I would have to ask Gideon if he could volunteer for an ECM swap to try that out....(very low possibility of happening, i think)
CTScott, if you could construct a device that broadcasts the speed data, I'd be willing to take that chance and option MORE than a ECM w/ ABS running on a car without an ABS system. I'd rather not have problems down the road w/ an ECM enabled for something and the actual car not having it at all.
CTScott, I'm willing to put down an extra $100+ towards your R&D work (seriously, just ask Gideon) to make the cluster work....
I'm keeping fingers crossed its the same message data from the Prius.
Converting 100 kmh to actual 100 mph? As awesome as it sounds, wouldn't the speed limiter have to be set to 120 kmh then, I dont think the car can handle going 180 kmh ~ 180 mph.....?
It actually wouldn't affect the speed limiter, as I would be getting the "correct" data from the ECM, and then broadcasting the adjusted data to the cluster.
GideonSunnyvale, CA · Oct 19, 2009#56 Originally Posted by
Kioshi ↑ For solution 1, I would have to ask Gideon if he could volunteer for an ECM swap to try that out....(very low possibility of happening, i think)
Noooope. Not messing around with my ECU. Sorry. 😆
This seems like a huge headache, I'm glad you have the patience and drive to get this to work.
Although I can give you a partial refund and give you my Canadian cluster. I forget what year it was from, but it was off of a Yaris w/o ABS that way you at least have a tach. 🙂
KioshiThread starterFremont, CA · Oct 19, 2009#57 Originally Posted by
Gideon ↑ Noooope. Not messing around with my ECU. Sorry. 😆
This seems like a huge headache, I'm glad you have the patience and drive to get this to work.
Although I can give you a partial refund and give you my Canadian cluster. I forget what year it was from, but it was off of a Yaris w/o ABS that way you at least have a tach. 🙂
Nope not letting you finish off the Vitz RS transformation 😆
Could you reconfirm that the Asian/Canadian cluster was off from a non-ABS Yaris? If thats the case, would an ECM w/ ABS work with the cluster on a non-ABS car...? hmmm....
CTScottUSA, CT · Oct 19, 2009#58OK - Big time progress. I captured the speed CAN messages on my 09 while driving my little one to dance class tonight. When I got home I analyzed the data and sure enough it is the ECM sending the speed to the cluster.
Here is a quick video of me telling your cluster that I'm revving up to 52 kmh. I have the cluster hooked up to Garm's 07 ECM on my desk with the core processor for my YarGauge project sending the messages that the ECM isn't:

KioshiThread starterFremont, CA · Oct 19, 2009#59You were right on dot suspecting the ECM to be the cause.
So could the core processor be somehow enabled to send speed signal to the cluster, via ECM?
CTScottUSA, CT · Oct 19, 2009#60 Originally Posted by
Kioshi ↑ You were right on dot suspecting the ECM to be the cause.
So could the core processor be somehow enabled to send speed signal to the cluster, via ECM?
Yes. My solution #2 is spot on. I can have my core talk to the non-ABS ECM to get the speed, and then retransmit it as the message that the cluster needs (and I can do the kmh to MPH translation).
KioshiThread starterFremont, CA · Oct 19, 2009#61Nice.
I'm still a bit confused about the kmh to mph translation/conversion....
Ie: if i were driving 60 kmh looking at the cluster, it would be transmitted as 60 mph if to be clocked by a radar gun? If so, then i would not have any use of going beyond 120 kmh?
Thanks Scott.
yarisugiハワイ · Oct 19, 2009#62Just imagine the letters "mph" instead of "kmh" - the numbers on the speedo will be the same.
That way, whatever you see on your speedometer will be the mph reading. (if I understand correctly)
CTScottUSA, CT · Oct 19, 2009#63 Originally Posted by
Kioshi ↑ Nice.
I'm still a bit confused about the kmh to mph translation/conversion....
Ie: if i were driving 60 kmh looking at the cluster, it would be transmitted as 60 mph if to be clocked by a radar gun? If so, then i would not have any use of going beyond 120 kmh?
Thanks Scott.
Correct. If I translate it then when you are doing 60 MPH the pointer will be at the 60kmh line. It would mean that the pointer would never see the right side. I wonder if that's how it works when they get reflashed from kmh to MPH, or do they change the overlay to correct the scale?
KioshiThread starterFremont, CA · Oct 20, 2009#64 Originally Posted by
CTScott ↑ Correct. If I translate it then when you are doing 60 MPH the pointer will be at the 60kmh line. It would mean that the pointer would never see the right side. I wonder if that's how it works when they get reflashed from kmh to MPH, or do they change the overlay to correct the scale?
Would this effect the rpm of the car then (relate correct rpms to engine speed), i guess i would just reach redline a lot sooner haha...
I can find the answer out tomorrow from Speedo, the place i will go to get my odometer flashed to correct mileage on my car currently...
KioshiThread starterFremont, CA · Oct 20, 2009#65CTScott - If it's too much trouble of translating kmh to mph, i wouldn't mind not having it done on the cluster. I kind of feel bad that I kind of reined on Lewis's cluster and had you work on mine before his, and his being the first priority...🙁
Unless Lewis is okay w/ it, then yeah...
It would be a learning experience for me to adjust myself to kmh as well...so yeah I wouldn't mind not having it translated if its to much time consuming~
LewisNJ · Oct 20, 2009#66ok with me Kioshi- we'll need to clone Scott- one genius is not enough!
CTScottUSA, CT · Oct 20, 2009#67The kmh to MPH conversion is no big deal (and would allow a metric cluster to be used without reflashing). I also realized that if the cluster has lower mileage than your car, I can change the ODO with no problem (the cluster doesn't speed limit, so I can feed it max speed {255 kmh}) until it gets to the correct mileage). So this would mean that the clusters could be used without reflashing.
Many of these things which I am learning with Kioshi's cluster will have applicability to Lewis's cluster as well. Even though he has ABS, if he decides to sell, rather than use the cluster, the non-ABS cluster converter could come in handy.
KioshiThread starterFremont, CA · Oct 20, 2009#68From what i remember, the RS cluster has 6080 kilos on it. My USDM cluster has roughly about 27,980 miles...
That would save me a trip to Speedo to get the cluster reflashed. That'd be really nice if you could adjust the odometers to the correct ones on my cluster. If you could let me know before you get to that step, I can give you the exact or a higher estimated number that i have at that time...
True, you could sell multiple copies of the non-cluster converter unit to those wanting to swap in the future.
P.S. with your cluster converter, this is going to be all plug n play, correct? I dont want to be splicing wires and whatnot, esp that smal of a gauge wires..lol
On a second thought, I'd actually like to see the needle hit the other side..dont know why :)
Lewis - so true 😆
CTScottUSA, CT · Oct 20, 2009#69 Originally Posted by
Kioshi ↑ From what i remember, the RS cluster has 6080 kilos on it. My USDM cluster has roughly about 27,980 miles...
That would save me a trip to Speedo to get the cluster reflashed. That'd be really nice if you could adjust the odometers to the correct ones on my cluster. If you could let me know before you get to that step, I can give you the exact or a higher estimated number that i have at that time...
True, you could sell multiple copies of the non-cluster converter unit to those wanting to swap in the future.
P.S. with your cluster converter, this is going to be all plug n play, correct? I dont want to be splicing wires and whatnot, esp that smal of a gauge wires..lol
Lewis - so true 😆
Sounds good on the ODO piece.
As for plug and play, it will be fairly so. The module will have require four tap splices to existing wires. They can be done at the cluster or at the OBDII port.
I still have to sort out the indicator issues as well. For those I can do cuts and jumps on the circuit board so you don't have to swap any wires.
KioshiThread starterFremont, CA · Oct 20, 2009#70 Originally Posted by
CTScott ↑ As for plug and play, it will be fairly so. The module will have require four tap splices to existing wires. They can be done at the cluster or at the OBDII port.
Your going to have to tell me how to do that, I've never tapped any wires into any other wires at all. I think the OBDII port would be easier, longer wires? Wires to the cluster seem very short and very little space to work with...
I think you can guide me on this later, when the cluster arrives to me...
CTScottUSA, CT · Oct 20, 2009#71 Originally Posted by
Kioshi ↑ Your going to have to tell me how to do that, I've never tapped any wires into any other wires at all. I think the OBDII port would be easier, longer wires? Wires to the cluster seem very short and very little space to work with...
I think you can guide me on this later, when the cluster arrives to me...
Agreed. The cluster wires are as tight as banjo strings. there's a good amount of slack at the OBD port.
POORSHANE CT · Oct 20, 2009#72Maybe an obdII plug?
CTScottUSA, CT · Oct 20, 2009#73 Originally Posted by
POORSHA ↑ Maybe an obdII plug?
That would be an option, but since it's driving the speedometer, I'd want it more permanent.
KioshiThread starterFremont, CA · Oct 20, 2009#74If tapping wires into other wires is easier than what I'm making it seem in my head, I'd go for that route (waiting on Scott's instructions 😛). Techinically, I'd like to keep the OBD II port open for something like..scangauge in the future...and like Scott said, for speedometer, so it should be permanent..
I've soldered wires, thats about it, but that was on R/C cars w/ 12 gauge wires~
GideonSunnyvale, CA · Oct 20, 2009#75 Originally Posted by
Kioshi ↑ Nope not letting you finish off the Vitz RS transformation 😆
Could you reconfirm that the Asian/Canadian cluster was off from a non-ABS Yaris? If thats the case, would an ECM w/ ABS work with the cluster on a non-ABS car...? hmmm....
Nooooooes!! 😢
Actually, I just got an email that one was found, a 2007 RS cluster so it'll be here in a few weeks. (Although it's for an auto tranny, so we'll see how that goes.) 😁
The Canadian cluster I have was off of a non-ABS Yaris. That I can confirm because I bought it from IKQ and they're pretty top notch on reporting.
What was originally sold to me as the "mad jdm tyte" cluster, I still don't know where it came from, so I don't know anything about it other than it worked in my car. I have the Canadian in my car right now, and the Euro (I'm guessing) cluster is in pieces as I try not to obliterate it by changing the LED colors for fun. 🙂
KioshiThread starterFremont, CA · Oct 20, 2009#76 Originally Posted by
Gideon ↑ Nooooooes!! 😢
Actually, I just got an email that one was found, a 2007 RS cluster so it'll be here in a few weeks. (Although it's for an auto tranny, so we'll see how that goes.) 😁
son of a bitch, there's no way to stop you, is there? 😆😢
I guess it'll be named as the infamous Asian cluster. You say Canadian, but I only see kilometers on the cluster and no mph....strange....
I'm sure the RS cluster will work on your car....👍
You got PM..lol
advocatelocation · Oct 21, 2009#77Do I see a swap occuring? And jesus james how many clusters do you have? If you have an extra one at the end of all this madness with a tach I'll probably buy it off you with the HIDs. Assuming I can pay off these damn seats in the next century😢
CTScottUSA, CT · Oct 21, 2009#78Update on progress with the JDM one:
I can read the vehicle speed from the ECM and send it to the cluster, so the pointer does the correct thing. The issue I am having now is that I can not reliably get it to increment the odo. There are two extra bytes in the CAN message that thus far I can't make sense of (nor find any documentation for). I'll have to do some more watching of data from my 09 to try to make some sense of it.
KioshiThread starterFremont, CA · Oct 21, 2009#79 Originally Posted by
CTScott ↑ Update on progress with the JDM one:
I can read the vehicle speed from the ECM and send it to the cluster, so the pointer does the correct thing. The issue I am having now is that I can not reliably get it to increment the odo. There are two extra bytes in the CAN message that thus far I can't make sense of (nor find any documentation for). I'll have to do some more watching of data from my 09 to try to make some sense of it.
To increase the kilometers on the odo to the correct ones on my stock cluster?
CTScottUSA, CT · Oct 21, 2009#80 Originally Posted by
Kioshi ↑ To increase the kilometers on the odo to the correct ones on my stock cluster?
That, and just having the odo function correctly.
KioshiThread starterFremont, CA · Oct 21, 2009#81Is the odo taking a slower time to show accurate kilo/miles traveled? Or just misses a few odometers every now and then?
I dont know if this would help or not....i know my stock cluster (adjusted) the miles/kilos i drove testing out the RS cluster. You could try to see after driving a bit, that if the RS cluster adjusts the miles it just did right after starting up your car again....?
CTScottUSA, CT · Oct 21, 2009#82 Originally Posted by
Kioshi ↑ Is the odo taking a slower time to show accurate kilo/miles traveled? Or just misses a few odometers every now and then?
I dont know if this would help or not....i know my stock cluster (adjusted) the miles/kilos i drove testing out the RS cluster. You could try to see after driving a bit, that if the RS cluster adjusts the miles it just did right after starting up your car again....?
It's only incrementing 1/10 km every once in a while (like one or two per hour). I am thinking that the extra bytes are some form of security in the packet to make it difficult to modify the odo data.
That auto update is interesting. The ECM separately receives and stores the mileage, so the cluster must grab a delta from the ECM on powerup. So far I have identified one message from the ECM to the cluster and four from the cluster to the ECM (which send the ECM the indicator status).
KioshiThread starterFremont, CA · Oct 21, 2009#83 Originally Posted by
CTScott ↑ It's only incrementing 1/10 km every once in a while (like one or two per hour). I am thinking that the extra bytes are some form of security in the packet to make it difficult to modify the odo data.
That auto update is interesting. The ECM separately receives and stores the mileage, so the cluster must grab a delta from the ECM on powerup. So far I have identified one message from the ECM to the cluster and four from the cluster to the ECM (which send the ECM the indicator status).
Those extra bytes can be override somehow when the odo gets reflashed though....
Is there any companies in your area that do odo reflashing? I was thinking of paying you to get it reflashed by a company and do a trial run to see if the odo is functioning correct kilos/miles traveled.....
I can do it here through Speedo, but just in case there is any adjustments that need to be made to the cluster itself, it'd be easier and in your hands already to take a look at and do.... (just a thought)
CTScottUSA, CT · Oct 21, 2009#84 Originally Posted by
Kioshi ↑ Those extra bytes can be override somehow when the odo gets reflashed though....
Is there any companies in your area that do odo reflashing? I was thinking of paying you to get it reflashed by a company and do a trial run to see if the odo is functioning correct kilos/miles traveled.....
I can do it here through Speedo, but just in case there is any adjustments that need to be made to the cluster itself, it'd be easier and in your hands already to take a look at and do.... (just a thought)
The extra byte issue has to do with making it function correctly on a daily basis. The reflashing is completely different.
KioshiThread starterFremont, CA · Oct 21, 2009#85I see.
Toyota really has to make it complicated from jumping 1-2 years ahead in the car model...
KioshiThread starterFremont, CA · Oct 25, 2009#86Any update on the message ID deciphering? Also, a bit thinking ahead, but what happens if out of those 11 remaining messages there is no link to the odo? Could you make another unit that helps the odo to increment accordingly?
I mean, i could...drive it as is, but i would have to calculate how many miles i drove whenever got back home....
CTScottUSA, CT · Oct 25, 2009#87 Originally Posted by
Kioshi ↑ Any update on the message ID deciphering? Also, a bit thinking ahead, but what happens if out of those 11 remaining messages there is no link to the odo? Could you make another unit that helps the odo to increment accordingly?
I mean, i could...drive it as is, but i would have to calculate how many miles i drove whenever got back home....
It's been a busy weekend, but I did make some progress Friday night. I have deciphered how the cluster sends the mileage back to the ECM, but am still working on the other direction.
KioshiThread starterFremont, CA · Oct 25, 2009#88good to hear. It gets closer and closer in solving how the two clusters work on USDM cars.
I meant no rush by my previous comment. I just had a thought and usually I like to prepare myself for worse case scenario.
Enjoy your weekend Birthday guy.
KioshiThread starterFremont, CA · Oct 29, 2009#89 Originally Posted by
CTScott ↑ I have the speedo working, but still can't get the odo correct. So far it either increments way too slow or way too fast.
From the OZ thread....
Around what estimate would it be that the odo is increasing too fast? If I have to change my oil sooner than 5000 miles...lets say at +/-1200 miles...i wouldn't mind. I just switched to Eneos 0w-20 oil for my car, it can go 10k before changing the oil...so just curious now~
CTScottUSA, CT · Oct 29, 2009#90You wouldn't want it in the high speed mode. The two modes I've been able to achieve so far are ~ .1 km per hour and ~.1 km per second.
KioshiThread starterFremont, CA · Oct 29, 2009#91 Originally Posted by
CTScott ↑ You wouldn't want it in the high speed mode. The two modes I've been able to achieve so far are ~ .1 km per hour and ~.1 km per second.
.1km per second is pretty fast, understood. What would be manageable then? In the hundredths or tenths digits ~.0025 km per second, if that's possible to get that low....
CTScottUSA, CT · Oct 29, 2009#92I'm not sure yet. The two that I've run into so far were achieved by experimenting with values that I captured from my 09. I really need to figure out the algorithm that is used for the values. I am thinking that it is related to bus timing between message transmissions.
KioshiThread starterFremont, CA · Nov 15, 2009#93I just wanted to throw this on here.
On Friday night, computerlove87 was kind off to let us take out his 09 Yaris S cluster to try onto advocate's 06 Yaris non ABS. To our surprise, the cluster works. The speed was give or take +/- 1-2 mph difference when advocate and I did a 20 mph side by side comparison run....
ABS light stays on but the speedometer works fine and the odo works correctly according to advocate.
CTScott, I was windering does the odo increasement really matter...because, talking to some people and knowing that the RS cluster does not have a maint. light on it..it wouldn't matter for me to be to be keeping track of when to oil change...I dont know?
Or if you've made progress on the odometer at this moment...
CTScottUSA, CT · Nov 15, 2009#94 Originally Posted by
Kioshi ↑ I just wanted to throw this on here.
On Friday night, computerlove87 was kind off to let us take out his 09 Yaris S cluster to try onto advocate's 06 Yaris non ABS. To our surprise, the cluster works. The speed was give or take +/- 1-2 mph difference when advocate and I did a 20 mph side by side comparison run....
ABS light stays on but the speedometer works fine and the odo works correctly according to advocate.
CTScott, I was windering does the odo increasement really matter...because, talking to some people and knowing that the RS cluster does not have a maint. light on it..it wouldn't matter for me to be to be keeping track of when to oil change...I dont know?
Or if you've made progress on the odometer at this moment...
Very interesting. It sounds like on 09s they may have gone back to the speedometer being fed from the speed sensor, rather than from the ECM by way of the ABS speed sensors.
The issue with having the ODO not increment would be that you'd have no idea as to how many miles you've driven (for maintenance purposes) and of course you wouldn't be able to sell the car with the non-functioning ODO in it.
I'm still trying to figure this out, but I think what you found with the 09 cluster may mean that I am chasing my tail. I've been trying to emulate my 09 ECM talking to my 09 cluster. I think I need to sniff the CAN bus on an 08 with ABS to see if the message structure is different (which based on the above, I am 99% sure it will be). Enviri lives fairly close to me and he has an 08 with ABS, so his car would be perfect.
KioshiThread starterFremont, CA · Nov 15, 2009#95kustom - what model was it swapped from and to what model? The mileage works and increments accordingly from advocate and I's study on last friday night. His was an 06, i remember seeing an 07or 08 swap, but not early as an 06 model.....and from what CTScott could be getting on, the message from the CAN bus could be difference depending on the year of the car~~
CTScott - have you PM'ed enviri about having him be a test car for the CAN bus study...
So which option would you be taking now? Have you got better results w/ the odo w/ playing around with different calculations/algorithms?
CTScottUSA, CT · Nov 15, 2009#96 Originally Posted by
Kioshi ↑ kustom - what model was it swapped from and to what model? The mileage works and increments accordingly from advocate and I's study on last friday night. His was an 06, i remember seeing an 07or 08 swap, but not early as an 06 model.....and from what CTScott could be getting on, the message from the CAN bus could be difference depending on the year of the car~~
CTScott - have you PM'ed enviri about having him be a test car for the CAN bus study...
So which option would you be taking now? Have you got better results w/ the odo w/ playing around with different calculations/algorithms?
I haven't hit him up yet, but I will in the near future.
Your JDM one is obviously not an 09 one based on what Kustom play is saying. I forgot about the fact that the 09 ones worked fine in older non-ABS cars. That confirms that Toyota changed the speedometer input back to normal in 09. It also shed some light on why I haven't been able to make sense of the data I am seeing on my 09. It looks like getting 08 ABS cluster comm data is going to be the key for your JDM cluster.
KioshiThread starterFremont, CA · Nov 16, 2009#97Totally didn't cross my mind till late last night. At last fridays meet, there was a Yaris member who is Wisher23 on YarisWorld...he has an 08 non-ABS Yaris S hatchback....w/ a tach in th cluster...
I dont know if this helps you in your further research...
I can contact him to see if he can volunteer for a quick swap on mines to see the results....
My Vitz RS cluster is from an 07 model.....not sure if i mentioned it on the OZ cluster via here~
I dont know why toyota changed the cluster messages for an 08 and revert back to 06-07 models....👎
CTScottUSA, CT · Nov 16, 2009#98Enviri and I are getting together this week so I can check out the comm on his ABS 08.
KioshiThread starterFremont, CA · Nov 16, 2009#99 Originally Posted by
CTScott ↑ Enviri and I are getting together this week so I can check out the comm on his ABS 08.
Sounds good, keep me updated on what you find out from his 08 ABS.
I hope your findings make the odo work correctly :)
I dont want either of us to be stuck at a dead end for several months.
And I'd be willing to pay for enviri's efforts in this research too....
CTScottUSA, CT · Nov 17, 2009#100OK. Good news and bad news: The good news is that Enviri just took a ride up to my place so we could do the test with his car. The bad news is that it turns out that his dealer sold him a Yaris with ABS, but he didn't actually get ABS.
So, I still need to find an 07 or 08 that has ABS to grab some data from.