Yarisworld Archive

Serious Autocrossers?

109 posts · 28,844 views · page 1 of 3

ozmddOriginal postDFW, TX · Oct 12, 2009#1
Not to suggest that you must be "serious" to enjoy autoX, but I'm looking for anyone who is/has also preparing their Yaris for SCCA classing beyond H-Stock.
I'm planning on running in ST all next year, and would like to run some regional events, maybe even Nationals, so proper prep is critical.

I can't do much else HP-wise, but I will be looking at class-legal chassis bracing and more suspension tuning/upgrades.

I'd like to start by getting your feedback about alignment specs that you've tried on the autoX track. Particularly the rear. I know many people like to run negative camber in the rear, but this would reduce rotation, which increases understeer, so not sure it is useful. What about rear toe settings?

I'm currently at -2.25 camber in front (each side) and zero toe. Thinking about trying a bit more, and maybe 1/16" toe-out. This car has to stay daily-driver -friendly.

After that, what ST-legal bracing options can anyone suggest or give feedback about?
While the Yaris is definitley not a class-killer in ST, I think it can be a competitive car. I ran less than 1.5 seconds behind a fully-prepped Focus SVT whose driver has placed at Nationals in that car before, so I dont' think we're out of the running completely.

Replies 108

TamagoOff Grid · Oct 12, 2009#2
no "bracing" is legal in ST or even FSP classes.

front strut tower bar is your limit. skip that useless rear "strut" tower "bar" as it does nothing but weigh your car down.

alignment, if you want to help with rotation, throw a Penguin Garage camber shim under the front lower bolt on either side of the rear hubs. that'll give you a bit of camber, but more importantly dial-out some of the aggressive toe-in that occurs (and worsens with lowering of the car)
lilredrocketDFW, Texas · Oct 12, 2009#3
You want to give some info on what your setup that you have now. I will give what I have picked up at different events and from other reliable sources.

A little toe out in the rear will help your car rotate more. Might want to think about getting some stiffer springs than your NF210's you already have a good wheel and tire setup. Lots of track time is one of the best things you can do.
mikenacaratoBrentwood, TN · Oct 12, 2009#4
Originally Posted by Tamago ↑
no "bracing" is legal in ST or even FSP classes.

front strut tower bar is your limit. skip that useless rear "strut" tower "bar" as it does nothing but weigh your car down.
an scca official classed me in FSP with my xbar, room bar, and under bars. 🤷
ozmddThread starterDFW, TX · Oct 12, 2009#5
Thx. I misspoke with the "bracing" term. My overall impression of the front strut tower bar is that it doesn't offer much improvement on our cars, due to the 1-bolt strut top design and the towers being attached to the firewall. Any mounts out there that actually tie the strut tops, and wouldn't that put a strain on the center shaft?
ozmddThread starterDFW, TX · Oct 12, 2009#6
Originally Posted by mikenacarato ↑
an scca official classed me in FSP with my xbar, room bar, and under bars. 🤷
That may be correct, but I do know that "odd"vehicles often get thrown into the SP or SM classes at our SCCA events, since they aren't likely to be protested there. Not planning to X-brace, so should be safe there. Thanks.
RHDVIPbBLouisville, KY · Oct 12, 2009#7
Tires. A rear sway bar helps. But setup is key. I run a slight bit of camber in the rear. Noticed a difference in rear grip.
ozmddThread starterDFW, TX · Oct 12, 2009#8
Originally Posted by RHDVIPbB ↑
Tires. A rear sway bar helps. But setup is key. I run a slight bit of camber in the rear. Noticed a difference in rear grip.
Yeah, got all that. Kumho Ecsta XS 205/50/15 on 15x7 Volk TE37's, TRD rear sway.

When you say "rear camber" do you mean positive or negative, and do you know how much? How about toe? Thx!
Yaris-xSyracuse · Oct 12, 2009#9
You can put any lowering spring shock combo(no coilovers) a TRD Rear Sway bar is legal in HS on Yaris but you should get the thickest sway bar possible for the yaris for the front and rear (Micro image I believe has a front) lowering springs, shocks, CAI, 18" wheels (anything to reduce body roll) My HS Yaris w/Rear Sway bar still loves to lift wheels off the ground.
lilredrocketDFW, Texas · Oct 12, 2009#10
Ummm... The weight of an 18" wheel would kill a Yaris at auto-x. A front sway bar is going to cause more inside wheel spin. Check out this thread about the front sway bar.

Ever tried removing the front swaybar?
ozmddThread starterDFW, TX · Oct 12, 2009#11
Originally Posted by Yaris-x ↑
You can put any lowering spring shock combo(no coilovers) a TRD Rear Sway bar is legal in HS on Yaris but you should get the thickest sway bar possible for the yaris for the front and rear (Micro image I believe has a front) lowering springs, shocks, CAI, 18" wheels (anything to reduce body roll) My HS Yaris w/Rear Sway bar still loves to lift wheels off the ground.
Umm, that might be why you are winning by such a large margin. The only class-legal mod you listed there (by SCCA rules) is upgrading the front sway bar. That's why its called "stock." You are driving an ST car.

Also, 18" wheels are VERY heavy, so not good for acceleration. No, the TRD, or any other rear sway is not legal in stock. Sorry to rain on your parade. Your results are still great, and it sounds like you are a terrific driver, but if you are protested, you will lose.
ozmddThread starterDFW, TX · Oct 12, 2009#12
Oh... adjustable shocks are legal, but not lowering springs (in HS).
Anyway...back to the original thread...
Yaris-xSyracuse · Oct 12, 2009#13
My car is completely legal all I have is a TRD Rear Sway bar(factory option) and sport exhaust which is allowed
TamagoOff Grid · Oct 13, 2009#14
Originally Posted by mikenacarato ↑
an scca official classed me in FSP with my xbar, room bar, and under bars. 🤷
you should be in a prepared class.

no TRIANGULATION is allowed.
kngrsllSpartanburg, SC · Oct 13, 2009#15
really, the last thing you need to worry about with the yaris is chassis stiffness. its a pretty damn good chassis actually. what you really want to do is improve grip, lose weight, and pick up power! i forget the exact rules of ST now, but its basically bolt ons.

grip: so grippy tires like the Toyo R1R is good at a 205/50/15 (i think 205 is the max width for ST?) there are very few shock choices available, with the Tokico Blues and HTS. The HTS has much higher valving and are adjustable. I have yet to see any data from any of the coilover companies shocks. there are very few springs available, the Teins are probably best for motorsports at 3kgF/3.5kgR. there are some sway bar options as well, front and rear through MicroImage. there are very few other parts available, so anything else will have to be creative and custom. as for alignment, crank in the front camber, toe out the front, and leave the rear alone at the minimum. The consensus around here is for the best handling, use springs, shocks, and rear sway bar but i havent followed anyones progress really so who knows how it works.

lightening: this is pretty limited as the car is already light. a light battery would probably help a ton. i havent looked into this area much, but i think its probably pretty limited in SCCA autox.

power: there are some bolt ons available, intake, header, pulleys, exhaust so on, all class legal.

now my opinion, i think the Yaris could actually be a decent ST car. you need grippy street tires, id say at least the Star Specs, but the R1R's are supposed to be better. ive even heard the new A08 is even better, but that will cost some coin. the current suspension up seems pretty tried and true, you should be fine with Blues, STechs, and a Rear bar. id try to get as much camber dialed in the front as you can, the car needs it. as for power, the mods will do a little, but dont expect a huge leap. i cant comment on the intakes, i think they would all perform about the same in general. the only header i would consider buying is the DC. i think an exhaust is a waste of money, if i wanted to do anything, id get a shop to make a straight pipe and just bolt it on when i go race to save a little weight. a pulley is nice, since its cheap, id get one. after that, we are pretty limited on class legal power mods. personally, id like to see what we can do with the camcon by power enterprises, it is used to modify vvti. may be able to pull a couple hp with it. the best thing we can really do is lighten as much as you can. i havent looked at the rules in a long time, but weight goes a long way! improves both speed and grip! id go with a light battery, lighter seats for sure. i need to look at the rules again and figure out where you can shed more weight before i can expound on that topic.

but yeah to get started: 15" light wheels, 205 grippy street tires, springs, shocks, rear sway bar should get you 90% of the way there. things like a dc header, pulley, intake, seat can all help a small amount in terms of performance. that is my personal set up and it has netted a couple 1st places in ST class at local events, but is in no way a nationals type set up. im experimenting with that now
RHDVIPbBLouisville, KY · Oct 13, 2009#16
I have a slight bit of negative camber in the rear. I don't remember what degree, but I can pull out the sheet if I knew where it was or go to the shop that did it and pull my records.
TamagoOff Grid · Oct 13, 2009#17
max width for ST is 245
WolfWingsKansas City, MO, USA · Oct 13, 2009#18
Originally Posted by Yaris-x ↑
You can put any lowering spring shock combo(no coilovers) a TRD Rear Sway bar is legal in HS on Yaris but you should get the thickest sway bar possible for the yaris for the front and rear (Micro image I believe has a front) lowering springs, shocks, CAI, 18" wheels (anything to reduce body roll) My HS Yaris w/Rear Sway bar still loves to lift wheels off the ground.
On a side-note, no, the TRD rear sway bar is not legal in Stock class. Automatically puts you into FSP, or one of the numerous ST? classes. Doesn't matter if you bought it from the dealership that way, the TRD rear sway bar is still a bolt-on sway bar, the car comes from the factory without any rear sway bar at all.
ozmddThread starterDFW, TX · Oct 13, 2009#19
Originally Posted by Yaris-x ↑
My car is completely legal all I have is a TRD Rear Sway bar(factory option) and sport exhaust which is allowed
That is not correct. Again, not trying to bust on you, but you should read the SCCA rules. Your car was not available from the factory with that part, therefore it is not class-legal. Just because Toyota sells it through their dealers doesn't make it legal. TRD also sells lowering springs and a CAI. It must have been produced at the factory in that configuration, in that model year, in the package you own. So, even if they start making the rear sway standard on the 2011 "S" package, you can't run it, because you dont; have that year/model.
Same thing goes for your 6.5" wide wheels.

Stock class is extremely strict, specifically because the cars are carefully class to be competitive. You are currently being given the most generous PAX index of any car in autocross, but your car has been given a significant handling improvement over your HS competitiors and the rest of the feild by way of your PAX. You wanna win that trophy fair-and-square, right?
If you doubt me, post the question on your local SCCA forum.
ozmddThread starterDFW, TX · Oct 13, 2009#20
Originally Posted by Tamago ↑
max width for ST is 245
Yes, but that's for STX and STU. ST/STS are limited to 225.
ozmddThread starterDFW, TX · Oct 13, 2009#21
Originally Posted by kngrsll ↑
really, the last thing you need to worry about with the yaris is chassis stiffness. its a pretty damn good chassis actually. what you really want to do is improve grip, lose weight, and pick up power! i forget the exact rules of ST now, but its basically bolt ons.

grip: so grippy tires like the Toyo R1R is good at a 205/50/15 (i think 205 is the max width for ST?) there are very few shock choices available, with the Tokico Blues and HTS. The HTS has much higher valving and are adjustable. I have yet to see any data from any of the coilover companies shocks. there are very few springs available, the Teins are probably best for motorsports at 3kgF/3.5kgR. there are some sway bar options as well, front and rear through MicroImage. there are very few other parts available, so anything else will have to be creative and custom. as for alignment, crank in the front camber, toe out the front, and leave the rear alone at the minimum. The consensus around here is for the best handling, use springs, shocks, and rear sway bar but i havent followed anyones progress really so who knows how it works.

lightening: this is pretty limited as the car is already light. a light battery would probably help a ton. i havent looked into this area much, but i think its probably pretty limited in SCCA autox.

power: there are some bolt ons available, intake, header, pulleys, exhaust so on, all class legal.

now my opinion, i think the Yaris could actually be a decent ST car. you need grippy street tires, id say at least the Star Specs, but the R1R's are supposed to be better. ive even heard the new A08 is even better, but that will cost some coin. the current suspension up seems pretty tried and true, you should be fine with Blues, STechs, and a Rear bar. id try to get as much camber dialed in the front as you can, the car needs it. as for power, the mods will do a little, but dont expect a huge leap. i cant comment on the intakes, i think they would all perform about the same in general. the only header i would consider buying is the DC. i think an exhaust is a waste of money, if i wanted to do anything, id get a shop to make a straight pipe and just bolt it on when i go race to save a little weight. a pulley is nice, since its cheap, id get one. after that, we are pretty limited on class legal power mods. personally, id like to see what we can do with the camcon by power enterprises, it is used to modify vvti. may be able to pull a couple hp with it. the best thing we can really do is lighten as much as you can. i havent looked at the rules in a long time, but weight goes a long way! improves both speed and grip! id go with a light battery, lighter seats for sure. i need to look at the rules again and figure out where you can shed more weight before i can expound on that topic.

but yeah to get started: 15" light wheels, 205 grippy street tires, springs, shocks, rear sway bar should get you 90% of the way there. things like a dc header, pulley, intake, seat can all help a small amount in terms of performance. that is my personal set up and it has netted a couple 1st places in ST class at local events, but is in no way a nationals type set up. im experimenting with that now
Thx. I'll look-into the VVTi controller, since that is a legal mod. I run 90% of the things you mentioned. I'm seat-shopping now. I run an Odyssey battery, and that's 25 lbs right there!
I'm also pretty sure that throttle controllers are legal, so I'm considering the Blitz.
Until I see a dyno chart, I'm holding-off on the headers. So far, my dyno numbers (107 whp) seem similar to people who have the header too, so not sure it does much.
Thanks for your great input!
lilredrocketDFW, Texas · Oct 13, 2009#22
For the springs what about the AOE Tigertech's they are 4k/3k. You can get them through Micro Image
TamagoOff Grid · Oct 13, 2009#23
Originally Posted by ozmdd ↑
Thx. I'll look-into the VVTi controller, since that is a legal mod. I run 90% of the things you mentioned. I'm seat-shopping now. I run an Odyssey battery, and that's 25 lbs right there!
I'm also pretty sure that throttle controllers are legal, so I'm considering the Blitz.
Until I see a dyno chart, I'm holding-off on the headers. So far, my dyno numbers (107 whp) seem similar to people who have the header too, so not sure it does much.
Thanks for your great input!
skip the throttle controller. mod the driver.
toadbowser's castle · Oct 13, 2009#24
Originally Posted by ozmdd ↑
That is not correct. Again, not trying to bust on you, but you should read the SCCA rules. Your car was not available from the factory with that part, therefore it is not class-legal. Just because Toyota sells it through their dealers doesn't make it legal. TRD also sells lowering springs and a CAI. It must have been produced at the factory in that configuration, in that model year, in the package you own. So, even if they start making the rear sway standard on the 2011 "S" package, you can't run it, because you dont; have that year/model.
Same thing goes for your 6.5" wide wheels.

Stock class is extremely strict, specifically because the cars are carefully class to be competitive. You are currently being given the most generous PAX index of any car in autocross, but your car has been given a significant handling improvement over your HS competitiors and the rest of the feild by way of your PAX. You wanna win that trophy fair-and-square, right?
If you doubt me, post the question on your local SCCA forum.
i thought - and i could very well be wrong - there was a little loop-hole called 'port installed option' that allows the trd rear anti-sway bar on models/years that had that option available? again, i don't autox(yet), but i've done a fair bit of reading on the matter of hs prep and i think there's nothing wrong with taking every LEGAL advantage you can.
TamagoOff Grid · Oct 13, 2009#25
Originally Posted by toad ↑
i thought - and i could very well be wrong - there was a little loop-hole called 'port installed option' that allows the trd rear anti-sway bar on models/years that had that option available? again, i don't autox(yet), but i've done a fair bit of reading on the matter of hs prep and i think there's nothing wrong with taking every LEGAL advantage you can.
well, it's only illegal if you get contested. and when a yaris starts whipping up on 1990 honda civics in H stock, then the civics will take notice. however, a yaris on street tires is NEVER going to be whupping up on ANYTHING in h stock..
anonymous userwindward oahu · Oct 13, 2009#26
If i could add to this topic. I've been solo-ing for 4 years. And in subarus, now that i've blown a motor, i've been racing the yaris for a few events. I plan to run it for the rest of this season, and possibly for the next.

With that said, I now know why Yaris-x is soo fast in his class. His car should be classed in Street touring. In hawaii region, as per scca classing, NO rear sway-bar allowed, as well as aftermarket spring/struts. You can replace your strut, but stock springs must be used. There are a few modifications to be done in H-Stock, and are mostly small bolt-on stuff like axleback exhaust, a front swaybar may also be added or removed. And R-comps (tires) are allowed. That's mostly it.

Here's my mods, and it's crappy, but i'm in ST because of them. Blitz intake, TWM SSK/shifter bushings, ultra room bar, and TRD swaybar. THAT'S IT!!
I am currently on hankook rs-2's in the front, and primewell's in the rear. I can kick out the rear and spin this car like no ones business!
I am getting smoked right now by 2 honda fits, a maxima, and a few other cars in ST. Mods would help i would think, but i'm trying to improve myself as a driver (although to be honest i'm pretty good w/ AWD) trying to learn FWD.

Yeah, good tires would help, maybe 20 more HP, some neg. camber upfront and a smidge in the rear. Some toe-out in the rear. But i can't see this car competing against miatas, esp. on tighter courses, which we run in our region a lot.

But i guess i will be the only one racing, as you guys will have winter break soon, so i'll post up my results.
TheRealEnthMiami, FL · Oct 13, 2009#27
not here papo, we got sun all winter ;D, if anything itll drop to 50
TamagoOff Grid · Oct 13, 2009#28
Originally Posted by anonymous user ↑
But i can't see this car competing against miatas, esp. on tighter courses, which we run in our region a lot.
that's because a yaris and a miata will never be in the same class, EVER ;)
anonymous userwindward oahu · Oct 13, 2009#29
Originally Posted by Tamago ↑
that's because a yaris and a miata will never be in the same class, EVER ;)
Yeah, thank god for that. Miatas have the power to weight of a go-kart!
2 of my buddies have around 240whp in a 2100 lb chassis.
ozmddThread starterDFW, TX · Oct 13, 2009#30
Originally Posted by Tamago ↑
well, it's only illegal if you get contested. and when a yaris starts whipping up on 1990 honda civics in H stock, then the civics will take notice. however, a yaris on street tires is NEVER going to be whupping up on ANYTHING in h stock..

Well, he appears to be whooping up on all kinds of cars, since he's 2nd overall in the SCCA region he runs in.
ozmddThread starterDFW, TX · Oct 13, 2009#31
Originally Posted by anonymous user ↑
Yeah, thank god for that. Miatas have the power to weight of a go-kart!
2 of my buddies have around 240whp in a 2100 lb chassis.
Miata and Yaris can't be in the same class because Miatas are 2-seater.

Your buddies Miatas would run in Modified classes, since they are obviously FI cars with that HP. I have a bunch of buddies here in the DFW Miatas that are similar.
TamagoOff Grid · Oct 13, 2009#32
MR2 >Miata

haha
mikenacaratoBrentwood, TN · Oct 13, 2009#33
Originally Posted by Tamago ↑
you should be in a prepared class.

no TRIANGULATION is allowed.
fsp is prepared.
ozmddThread starterDFW, TX · Oct 13, 2009#34
Originally Posted by Tamago ↑
MR2 >Miata

haha
Depends on the driver, but often that is true. I've seen peopel drive the shit out of CRX's and beat well-prepared miatas and mr2's
anonymous userwindward oahu · Oct 13, 2009#35
Originally Posted by mikenacarato ↑
fsp is prepared.
F- STREET PREPARED is not prepared (eg.- FP,/EP/BP, etc.)

Prepared classes are where you would be with the gt-spec under bars.
And a yaris has no place in ANY prepared classes. Go look up what runs in prepared classes.
anonymous userwindward oahu · Oct 13, 2009#36
Originally Posted by Tamago ↑
MR2 >Miata

haha
Why, b/c it's a toyota? 👍 I plan to get one in the near future, if i can find one.
mikenacaratoBrentwood, TN · Oct 13, 2009#37
well they classed me with all of that...so im in the right class as far as im concerned. there was a day when a regional technician (i guess thats what you would call him) came to one of our events and was classing the members. He looked at everything and even noted i didnt have an airbag and put me in FSP. he did mention something about since the bars were not welded in and were removeable, i could be in this class. im not going to argue with him.
Yaris-xSyracuse · Oct 13, 2009#38
I Have worked in sales at a toyota dealer for 2.5 years and the TRD Rear sway bar is able to be installed by toyota pre-dealer (Port installed) Lowering springs are only Dealer installed or I would have them too. I can produce the production codes if you don't believe me. The rule book specifically says Port installed options are the same as Factory installed options.
TamagoOff Grid · Oct 13, 2009#39
Originally Posted by anonymous user ↑
Why, b/c it's a toyota? 👍 I plan to get one in the near future, if i can find one.
1. because it's mid engined.
2. because it's lightweight and makes decent torque
3. because it's a toyota
4. because it's different. everyone and their mother (or gay father) has a miata. Mazda flooded the market while toyota capped production numbers.. when the miata is worth 500 dollars, the MR2's will still be worth 2000 .
TamagoOff Grid · Oct 13, 2009#40
Originally Posted by Yaris-x ↑
I Have worked in sales at a toyota dealer for 2.5 years and the TRD Rear sway bar is able to be installed by toyota pre-dealer (Port installed) Lowering springs are only Dealer installed or I would have them too. I can produce the production codes if you don't believe me. The rule book specifically says Port installed options are the same as Factory installed options.
i think you better start producing these rules from the SCCA 2009 rule book then 🙄
TamagoOff Grid · Oct 13, 2009#41
Originally Posted by mikenacarato ↑
well they classed me with all of that...so im in the right class as far as im concerned. there was a day when a regional technician (i guess thats what you would call him) came to one of our events and was classing the members. He looked at everything and even noted i didnt have an airbag and put me in FSP. he did mention something about since the bars were not welded in and were removeable, i could be in this class. im not going to argue with him.
what's beating you in FSP ?
mikenacaratoBrentwood, TN · Oct 13, 2009#42
theres only 2 other cars in fsp. 1 miata and 1 wrx, its always a tossup between us
Yaris-xSyracuse · Oct 13, 2009#43
TRD Rear sway bar Production code HR

2009 SCCA SOLO Rules
12.4 STANDARD PART
An item of standard or optional equipment that could have been
ordered with the car, installed on the factory production line, and
delivered through a dealer in the United States. Port-installed options
provided by the factory are considered to be the same as
those installed on the factory production line.
Dealer-installed options
or deletions (except as required by factory directives), no matter
how common or what their origin, are not included in this definition.
This definition does not allow the updating or backdating of parts.
ozmddThread starterDFW, TX · Oct 13, 2009#44
SCCA National Solo Rules 2009
13.7 ANTI-ROLL (SWAY) BARS
A. For front anti-roll (sway) bars:
1. Substitution, addition or removal of any front anti-roll bars is
permitted.
2. Substitution, addition or removal of anti-roll bars may serve
no other purpose than that of an anti-roll bar.
3. The use of any bushing material is permitted.
4. No modification to the body, frame or other components to
accommodate anti-roll bar addition or substitution is allowed,
except for the drilling of holes for mounting bolts. Nonstandard
lateral members which connect between the brackets
for the bar are not permitted.
B. Rear anti-roll (sway) bars may not be removed, replaced, or
modified in any way.


From Section 13 "Stock"
Alternate parts listed in a factory parts manual are not authorized unless their use is specifically referenced in the factory service
manual or in a service bulletin for the specific model


Please show me the "port option exception" as it only exists in the Solo rules when it pertains to specific vehicles that have been listed in the "Stock Class Clarifications" section in the appendix. There isn't one for the Yaris, but the ones that do exist are items that MUST APPEAR ON THE WINDOW STICKER (not the dealer's add-on sticker.) EX. The WRX allows the port-added CF dash overlay, boost gauge and armrest.
ozmddThread starterDFW, TX · Oct 13, 2009#45
Originally Posted by Yaris-x ↑
TRD Rear sway bar Production code HR

2009 SCCA SOLO Rules
12.4 STANDARD PART
An item of standard or optional equipment that could have been
ordered with the car, installed on the factory production line, and
delivered through a dealer in the United States. Port-installed options
provided by the factory are considered to be the same as
those installed on the factory production line.
Dealer-installed options
or deletions (except as required by factory directives), no matter
how common or what their origin, are not included in this definition.
This definition does not allow the updating or backdating of parts.
You just made my point. There is no factory-provided part here. Again, read the quote in blue in the above post. There is no such thing as a factory-installed rear sway bar on a US Yaris. The rule you quote clearly states that a factory-available part can ALSO be installed at the port instead of the actual factory and still be considered "standard."
Yaris-xSyracuse · Oct 13, 2009#46
TRD is toyota toyota will install the toyota Rear sway bar at NY PORT and it would appear on the toyota build sheet as (PPO-HR TRD Rear Sway bar)
ozmddThread starterDFW, TX · Oct 13, 2009#47
Again, you can't ignore the part of the rule that says that the option must be a factory option. This is not. Since you work at the dealer, show me the factory-option rear sway. And no, TRD is not Toyota. Not to SCCA. They have another section that refers to manufacturer-supported performance division parts. And that section ain't in "Stock."

Lets see your build sheet. Even if the rear sway was factory-available, the burden-of-proof would be on you to show that the part was legal. And you would have to have every other part available in that package, and the same year-model vehicle.
You can't cherry-pick the rule book.
Again, don't you want to win your trophy fair-and-square? Its not worth bragging about if you won it wrongly. Even Andy Hollis gave-up his title last year when he realized his motor wasn't 100% legal, by no fault of his own, and nobody would have ever realized it.
Integrity is what makes the sport fun. As good as you drive, you should still be able to place in ST, or run your events w/o the sway bar and class-illegal wheels.
ozmddThread starterDFW, TX · Oct 13, 2009#48
Of course, you could also announce your non-complying mods to the other drivers in your class and ask for an exception. The you're legit. Lotsa people do that. I ran my Miata w/ an automatic radiator (metal) instead of the plastic one that comes in manual trannys and just told my competitors. They didn't care that I had an extra 4 pounds on my car, and I was legit.

I suspect that if you told your competitors about your changes, they might not feel it was fair. Maybe the wheels, but not the sway bar. I guess you could just ask them?
Yaris-xSyracuse · Oct 13, 2009#49
Ok if you go to the dealer and buy a Yaris in "A" category and it still hasn't hit American soil. You can request that your yaris come in with a TRD Rear sway bar. When it hits NY PORT or whatever port your region receives yaris from it will go into a second assembly line state side where they will put on your Sway bar and Floor mats and whatever else toyota wants put on there. The Yaris will come into the dealer with the sway bar listed on the window sticker and if you print off the Vehicle inquiry then or 10 years from now in the Dealer Trac system it will list the Sway bar as an option on that vehicle. As for my wheels yes they are .5" too wide but they were approved by my regions solo chair and I do know if I went to compete in another region or at a higher event they may not pass but I am not running wider tires and I'm not even running slicks so I did so with the blessing of my regions SOLO chair.
ozmddThread starterDFW, TX · Oct 13, 2009#50
Still not a factory item. Glad you did the right thing on the wheels. Good luck!