Yarisworld Archive

DIY Projector/HID (sedan)

146 posts · 119,345 views · page 1 of 3

BrianOriginal postRiverside, CA · Sep 6, 2009#1
Here is the DIY for the projectors from Micro Image. This DIY was design for the sedan but most of the steps can be related to the LB as well. Perform at you own risk. If you have any questions feel free to ask or PM me.

Tools needed: 10mm socket
14mm socket (I think for negative battery terminal)
Ratchet (1/4" drive works fine)
Phillips screwdriver
Flat head screwdriver
Masking tape
Dremel

1.) Disconnect negative (-) wire from battery
2.) Lift vehicle (just the front end or the whole car)
3.) Apply masking take to bumper and fender (prevents paint from getting scratched)
4.) Remove these bolts from the front of the inner fenders with 10mm socket(1 on each side)


5.) Remove bolts from underside holding the bumper and underpanels on (no pic). I think theres about 6 or 8 of them.
6.) Remove 6 push rivets from the top of bumper under the hood. Push down in the middle of them and pull the whole thing out.

7.) Pull the sides of the bumper outwards to release. It should now look something like this:

8.) Headlight removal. There are 3 10mm bolts holding each headlight on. 2 on top and 1 on the side and unplug 2 OEM connectors. If you have eyelids remove them at this time.



9.) Remove all factory wiring and bulbs from each headlight and the 3 screw from the edge of the back of the headlight.

10.) You should end up with this:

11.) Remove the screw holding the headlight bulb clip. (You will not need these)

12.) Now its time to bake your headlights. Preheat oven to 215-225 degrees. Once the oven is heated place one headlight at a time on a cookie sheet with aluminum foil. Set oven rack so the headlight will be as close to the center of the oven as possible. Bake for about 10 minutes.
13.) Remove from oven. CAUTION HEADLIGHT WILL BE HOT. Use a pair of gloves to handle it.
14.) Starting at one corner use a flathead screwdriver or butter knife and pry the lens from the housing. Don't be affraid to use a little force if necessary. Once you get on corner separated you can pretty much just pull the lens from the housing by hand and a little strength.
15.) Once removed you should have this:


16.) There are 3 phillips screw holding the reflector housing to the lens. Remove these and be careful not to lose. They are small.

17.) Remove reflector housing from lens. Sorry no pics.
18.) I don't remember but I think there are 2 more small phillips screw hold the reflector housing together. Remove these and pop out the reflector. Remove the headlight bulb reflector from the housing by prying up the two tabs and pushing the reflector out.
19.) This next part is up to you. You can paint any color. I used SEM satin black. Does not need to be a high temp paint.
20.) Mask of all around the headlight housing to prevent dust from sanding and paint from contacting sealant.

21.) Scuff sand all chrome parts of the headlight housing and reflector housing with 600 grit or higher sandpaper.
22.) Paint and allow to dry.



23.) Remove plastic from the projectors and unscrew and remove the 2 rings, washer, and H4 ring.
24.) Insert projector into headlight housing from the front and on the back install H4 ring, washer, threaded ring without the tabs (projector is labled top). Tighten all the way.


25.) Reassemble the reflector housing and lens assembly.


The reflector housing will have to be notched to accomodate the projector. No pics, but it you put the to parts together you will see. No big deal if you have a dremel.
26.) Remove masking tape from the headlight assembly. You can use and apply some of the sealant now or, like I did, wait until the headlights are assembled and run a bead around the outside.
27.) Back to baking. Put the headlights in the oven again at the same temperature for the same amount of time.
28.) Remove headlight from the oven and, while wearing some gloves, push the lens assembly into the headlight housing assembly while trying to line up the 3 screw holes and clips around the outside. Insert the screw and allow to cool.
29.) When finished it will look something like this:


30.) Now for the wiring. Reinstall the factory harness into each headlight housing, don't forget the factory grommet, along with the HID bulb and screw ring with the tabs on it.

31.) The projector kit comes with a pack of phillips screws. Use one on each headlight to mount the ballast on the bottom.


32.) The HID harness with the long power wire goes on the passenger side.
33.) Run the single red power wire to the battery and attached them to the positive (+) post. I ran the passenger side along the firewall and the drivers side behing the battery.

34.) Passenger side. Attach the single black ground wire to the strut tower (make sure to grind down to bare metal) and mount the black relay box on top of the ground wire utilizing the threaded hole already there. The bolts in the kit fit perfectly.

35.) Driver's side single black gound wire. There is already a ground wire, by I think its the airbag sensor, you can use.

36.) Plug all the other wires together, except the single red and black wires with no terminal and bare wire showing.
37.) Now for the halos. The single red and black wires with no terminals. Use the provide wire splicers or you can solder. Attach the black wire to the white wire w/black strip (-) coming out of the connector for the signal lights and the red wire to the green wire (+) on the opposite corner of the connector.


I zip tied the wire splicers then wrapped them in electrical tape to prevent them from coming undone.

38.) Bolt the headlight assemblies back on with the 3 bolts each and reinstall the bumper.
39.) End result:






And the cut off.

Replies 145

ruimondPerth, Australia · Sep 6, 2009#2
That looks awesome. Well done on doing it yourself and making a DIY for other people to follow.

I think someone should start making pre-made ones with these kits for people to buy for people who aren't keen to DIY. Instead of those ones made in Taiwan.
808_YarisHI · Sep 6, 2009#3
Wow! Great work Brian! How long did that take you?
BrianThread starterRiverside, CA · Sep 6, 2009#4
Took me about 6-7 hours. Taking my time and making sure everything was right. With the DIY it can probably be done in 3-4 hours
DandiDaniJeff,Indiana · Sep 6, 2009#5
thanx a lot for posting this. my husband plans to do this next week sometime. im sure ill be helping him and that you will receive some pm's.🆘😆
JeremyGMalaysia, Sabah-KK · Sep 6, 2009#6
Congrats on successfully completed your DIY. Just a quick question, what does the color output of the 5000k bulb? is it Yellowish, White, or yellowish-white?
JumpmanYarisSO. INDIANA · Sep 6, 2009#7
I am screwd on the wire part🙁
PETERPOOPOahu · Sep 6, 2009#8
awesome job. thanks brian. ill pm you if i have any questions today during my install. thanks
JumpmanYarisSO. INDIANA · Sep 6, 2009#9
Originally Posted by PETERPOOP ↑
awesome job. thanks brian. ill pm you if i have any questions today during my install. thanks
Are you posting picture Peter??
BrianThread starterRiverside, CA · Sep 6, 2009#10
Originally Posted by JeremyG ↑
Congrats on successfully completed your DIY. Just a quick question, what does the color output of the 5000k bulb? is it Yellowish, White, or yellowish-white?
5000K is more white. The ones in the pics are 6000k which have a hint of blue but mostly white.
PETERPOOPOahu · Sep 6, 2009#11
Originally Posted by JumpmanYaris ↑
Are you posting picture Peter??
Probably not since brian was kind of enough to do this DIY. However, I might because mine is a liftback. If I encounter anything different from his DIY, i'll be sure to take pics and write something.
BrianThread starterRiverside, CA · Sep 6, 2009#12
Originally Posted by PETERPOOP ↑
Probably not since brian was kind of enough to do this DIY. However, I might because mine is a liftback. If I encounter anything different from his DIY, i'll be sure to take pics and write something.
You should do one to show how to take apart the headlights and work with them
BrianThread starterRiverside, CA · Sep 6, 2009#13
Originally Posted by JumpmanYaris ↑
I am screwd on the wire part🙁
The wiring is probably the easiest part. Theres pretty much only one way to do it.
JumpmanYarisSO. INDIANA · Sep 6, 2009#14
Ok so this are HID as well?
BrianThread starterRiverside, CA · Sep 6, 2009#15
Originally Posted by JumpmanYaris ↑
Ok so this are HID as well?
yes
JumpmanYarisSO. INDIANA · Sep 6, 2009#16
Originally Posted by Brian ↑
The wiring is probably the easiest part. Theres pretty much only one way to do it.
And what way is that?🤷
BrianThread starterRiverside, CA · Sep 6, 2009#17
Originally Posted by JumpmanYaris ↑
And what way is that?🤷
I figured it out on the first try. I thought the halos were gonna be hard but they weren't. Just tap into 2 wires on each light and every thing else just plugs together. Only fits on way.
JumpmanYarisSO. INDIANA · Sep 6, 2009#18
Originally Posted by Brian ↑
I figured it out on the first try. I thought the halos were gonna be hard but they weren't. Just tap into 2 wires on each light and every thing else just plugs together. Only fits on way.
😕 I shall try it then
LEGATO``Virginia Beach · Sep 6, 2009#19
hmm i have eyelids, and i believe you had eyelids to brian

do you plan on putting them back on? or is the cutoff going to be different?
PETERPOOPOahu · Sep 6, 2009#20
doing mine, getting ready to bake..
1NZYaris1New Zealand · Sep 6, 2009#21
watching and waiting 🤤
PETERPOOPOahu · Sep 6, 2009#22
pulled apart one headlight, preheating for the next one.
JumpmanYarisSO. INDIANA · Sep 6, 2009#23
Originally Posted by PETERPOOP ↑
doing mine, getting ready to bake..
and shake!!
PETERPOOPOahu · Sep 6, 2009#24
had to use a dremel to have the projector fit in the housing. the original hole for the stock bulb was too small and could not fit the projector. good thing it was checked before i sprayed the housing black. just taped off the headlights, and getting ready to spray.
JumpmanYarisSO. INDIANA · Sep 6, 2009#25
I am still looking for another set of headlights on ebay looks like its about 45 to 115 the average on price. any cheaper then that before I buy any of them
PETERPOOPOahu · Sep 6, 2009#26
i dont think they come any cheaper;but i don't think you need to buy them either. i only set my oven to 215 and preheat for 10 minutes and let the headlights sit in there for 4 min and that was enough time to pry it open. all ovens are different so you have to decide how long you want to put them in there for. one of the headlights actually melted in the back a little bit after only being in there for four minutes. so keep an eye on it
JumpmanYarisSO. INDIANA · Sep 6, 2009#27
Will do
BrianThread starterRiverside, CA · Sep 6, 2009#28
Originally Posted by LEGATO`` ↑
hmm i have eyelids, and i believe you had eyelids to brian

do you plan on putting them back on? or is the cutoff going to be different?
I don't think the cut off will be affected. I will probably repaint them and try them out next weekend.
LEGATO``Virginia Beach · Sep 6, 2009#29
Originally Posted by Brian ↑
I don't like the cut off will be affected.

you mean you "dont think the cut off will be affected" ?
cali yarisCanoga Park, CA · Sep 6, 2009#30
^ He meant by the eyelids, I think.

Brian, great DIY and thank you for taking the time to post it. Looks good and it seems the issues were minor. Are the halos nice and bright?
JeremyGMalaysia, Sabah-KK · Sep 6, 2009#31
Originally Posted by Brian ↑
5000K is more white. The ones in the pics are 6000k which have a hint of blue but mostly white.
hmm very different from what mine looks like at 6000K temperature. Do you mind post up the picture of the bulb for the projector lens? 😳 Appreciate your effort Brian😉
BrianThread starterRiverside, CA · Sep 6, 2009#32
Originally Posted by cali yaris ↑
^ He meant by the eyelids, I think.

Brian, great DIY and thank you for taking the time to post it. Looks good and it seems the issues were minor. Are the halos nice and bright?
Yeah, I meant "think". Fixed it now. The halos are very bright. I tried taking some pics of them from the front but they ended up looking like the actual headlight was on so I had to do it from the sides.

Originally Posted by JeremyG ↑
hmm very different from what mine looks like at 6000K temperature. Do you mind post up the picture of the bulb for the projector lens? 😳 Appreciate your effort Brian😉
It looks the same as any other HID bi-xenon bulb. Sorry don't have any pics. Maybe Peterpoop can snap a pic before he finishes.
PETERPOOPOahu · Sep 7, 2009#33
Originally Posted by Brian ↑

It looks the same as any other HID bi-xenon bulb. Sorry don't have any pics. Maybe Peterpoop can snap a pic before he finishes.
Doh, didn't see this until now. Too late. Sorry.
808_YarisHI · Sep 7, 2009#34
^did you finish? 😁
LEGATO``Virginia Beach · Sep 7, 2009#35
hmm okay
well the installation definitely seems easy enough with your diy brian. greatly appreciated 👍

one thing; i just read peter's diy
and i know that he had to make the whole bigger for the projectors, but you didn't. and i dont own a dremel.
did you have to use a dremel for anything?
BrianThread starterRiverside, CA · Sep 7, 2009#36
one thing I completely forgot to check was the high beams.
PETERPOOPOahu · Sep 7, 2009#37
Originally Posted by Brian ↑
one thing I completely forgot to check was the high beams.
let me know if they work! lol

Originally Posted by 808_Yaris ↑
^did you finish? 😁
DIY Projector/HID (Liftback)
BrianThread starterRiverside, CA · Sep 7, 2009#38
Originally Posted by LEGATO`` ↑
hmm okay
well the installation definitely seems easy enough with your diy brian. greatly appreciated 👍

one thing; i just read peter's diy
and i know that he had to make the whole bigger for the projectors, but you didn't. and i dont own a dremel.
did you have to use a dremel for anything?
i used a dremel to cut a notch in the relector housing and to sand the paint off a spot for the grounging point. I'm sure you can get by with a flat file though. just might take a little longer.
BrianThread starterRiverside, CA · Sep 7, 2009#39
Originally Posted by PETERPOOP ↑
let me know if they work! lol



DIY Projector/HID (Liftback)
Just checked and works fine.
LEGATO``Virginia Beach · Sep 7, 2009#40
oh okay
thanks for the info
Red HorseCosta mesa, California · Sep 7, 2009#41
no high beam?
BrianThread starterRiverside, CA · Sep 7, 2009#42
Originally Posted by Red Horse ↑
no high beam?
Yes, it's a bi-xenon. Hi beam works perfect also. No pics yet though.
BrianThread starterRiverside, CA · Sep 7, 2009#43
Thanks. I plan on getting a new set of headlights in a few months cause mine have taken a beating the last couple of years from rocks and the clear protectant is beginning to wear off on the lens. When I do I will get some better pics of the install. All I had was my phone at the time. I'm very happy with the outcome though and love the blacked out look.
JeremyGMalaysia, Sabah-KK · Sep 7, 2009#44
Brian, does this bulb looks the same as yours?


mine was labeled 6000K but I didn't expect the output was yellowish instead of white-bluish.


Oh yea one more question Brian, Does the H4 ring adapter sits your projector properly? or did you discard them to get your desire level on the light output?
BrianThread starterRiverside, CA · Sep 7, 2009#45
yes, its a D2S
JumpmanYarisSO. INDIANA · Sep 7, 2009#46
Can someone fotoshop the headlights with the projectors in red housing? I am curious to see how it looks with the blk car lol
JeremyGMalaysia, Sabah-KK · Sep 7, 2009#47
Originally Posted by JeremyG ↑
Oh yea one more question Brian, Does the H4 ring adapter sits your projector properly? or did you discard them to get your desire level on the light output?
Brian, how bout this question? 😳
BrianThread starterRiverside, CA · Sep 7, 2009#48
Originally Posted by JeremyG ↑
Brian, how bout this question? 😳
It fit perfectly
JeremyGMalaysia, Sabah-KK · Sep 7, 2009#49
hmm looks like that adapter ring are purely for LH driver cause our (asia) design will shoot 140 degree angle with that ring fitted in... :(
LEGATO``Virginia Beach · Sep 7, 2009#50
i was looking through one of the threads that peter put up and you asked him about his cutoffs

did you have any trouble adjusting yours or did you just plug them in and they were already set to go pretty much?