Yarisworld Archive

DIY Projector/HID (sedan)

146 posts · 119,345 views · page 2 of 3

Replies continued

BrianThread starterRiverside, CA · Sep 7, 2009#51
Originally Posted by LEGATO`` ↑
i was looking through one of the threads that peter put up and you asked him about his cutoffs

did you have any trouble adjusting yours or did you just plug them in and they were already set to go pretty much?
I tried to adjust them but since the projectors hit the reflector housing they barely went lower than
the factory setting. I liked the height of the cut off so I left it alone. Just got back from a night drive
and I saw absolutly no glare and a perfect cut off. The cut off height is perfect and doesn't shine
into other peoples mirrors. A huge improvement from running my previous HIDs in the stock
housing. With my previous HIDs there was glare all over the place and would constantly shine
Into other driver's mirrors. With the projectors there is plenty of light on the road. I must
recommend that anyone with HIDs upgrade to these projectors, atleast for the safety and courtesy
of the other driver's.
JumpmanYarisSO. INDIANA · Sep 13, 2009#52
I am still waiting on my projectors, I think they might be in tomorrow.
PETERPOOPOahu · Sep 14, 2009#53
Hey brian, I've never had an HID kit before, so I was wondering if this was normal; When I turn on the low beams, it takes a few seconds to "warm up." It's not as bright at first. But then the projectors get brighter gradually, until it's peak. Are you experiencing this too? Or is this even normal?

Also, i've had this happen a couple of times; when I go to just turn the halos on, they won't turn on immediately. Maybe a few seconds, then they pop on. I know those don't have to "warm up," because I usually can just turn the halos on and they turn on right away. However, one time I tried to turn the halos on, and they didn't turn on. It wasn't until I flipped my lights on all the way ( to turn the low beams on ), is when the halos went on too. Then I turned the projectors off and just left the halos on, and it seemed to work fine after that. Very strange. It can't be a wiring issue, because all the lights DO work. It just depends on how long they want to take for them to eventually turn on ( the halos ). Hopefully this isn't a sign of bad things to come? dun dun dun.......

On a positive note, I've had many compliments on the headlights. I am extremely glad I went with blacking out the housings, and it gives my car a much more sportier, less eco-box feel IMO!!!!!!!!
ezhacker1San Francisco · Sep 14, 2009#54
HIDs DO warm up, so its normal.
PETERPOOPOahu · Sep 14, 2009#55
oh ok, thanks. I guess the thing with the halos is the only mystery now.
ImportRacer88Meshoppen, Pa 18630 · Sep 16, 2009#56
ok i dont know if this was answered what was the total cost of meterials i would like to do this and what if i didnt get the hids but wanted to paint the chrome black will that drasticly affect my visibilty and light out put of the headlights
JeremyGMalaysia, Sabah-KK · Sep 20, 2009#57
Originally Posted by PETERPOOP ↑
Also, i've had this happen a couple of times; when I go to just turn the halos on, they won't turn on immediately. Maybe a few seconds, then they pop on. I know those don't have to "warm up," because I usually can just turn the halos on and they turn on right away. However, one time I tried to turn the halos on, and they didn't turn on. It wasn't until I flipped my lights on all the way ( to turn the low beams on ), is when the halos went on too. Then I turned the projectors off and just left the halos on, and it seemed to work fine after that. Very strange. It can't be a wiring issue, because all the lights DO work. It just depends on how long they want to take for them to eventually turn on ( the halos ). Hopefully this isn't a sign of bad things to come? dun dun dun.......
I had this problem too and culprit it's at the controller (square size little black box) that comes with the wiring harnesses. While having the issue of slow respond on the Halo (left side only), it will slowly died off.

Just to make sure that Box was the culprit, you can switch between the two Box to see which ones are faulty. There's a connector on the bottom of the box so just unplug them, not the whole wiring. Hope this helps.
BrianThread starterRiverside, CA · Sep 20, 2009#58
I haven't had any problems with my halos so far. The only thing I can suggest is to double check
and make sure there are no loose wires.
E.R.GAruba · Sep 21, 2009#59
Where can i get one set of those projectors?
E.R.GAruba · Sep 21, 2009#61
Thanks PETERPOOP.👍
PETERPOOPOahu · Sep 21, 2009#62
no problem!
cali yarisCanoga Park, CA · Sep 21, 2009#63
^ love that signature pic
JumpmanYarisSO. INDIANA · Sep 22, 2009#64
Well just got the projectors today woooohhhoooooo👍
Thanks GARM even tho u forgot about me
JumpmanYarisSO. INDIANA · Sep 22, 2009#65
🤤🤤🤤
102_0782.jpg
RHDVIPbBLouisville, KY · Sep 22, 2009#66
^^^^sweet. Now come over and lets install them.
PETERPOOPOahu · Sep 22, 2009#67
good luck!
LEGATO``Virginia Beach · Sep 24, 2009#68
i looked at jumpman's picture before i went to bed lastnight
and i had a dream that i got one in the mail too
do you know how much it suck when i woke up?

anyways
good luck with the install!
JumpmanYarisSO. INDIANA · Oct 6, 2009#69
Originally Posted by LEGATO`` ↑
i looked at jumpman's picture before i went to bed lastnight
and i had a dream that i got one in the mail too
do you know how much it suck when i woke up?

anyways
good luck with the install!
It had happend to me before it sucks
1NZYaris1New Zealand · Oct 6, 2009#70
Originally Posted by LEGATO`` ↑
i looked at jumpman's picture before i went to bed lastnight
and i had a dream that i got one in the mail too
do you know how much it suck when i woke up?

anyways
good luck with the install!
Atleast you didn't buy them , ship them half way around the world .
then unpack them & paint them ,then to find the cut off was wrong 😳
That sucks , trust me .😆 😆 😆
live and learn 🤣
JeremyGMalaysia, Sabah-KK · Oct 6, 2009#71
Originally Posted by 1NZYaris1 ↑
Atleast you didn't buy them , ship them half way around the world .
then unpack them & paint them ,then to find the cut off was wrong 😳
That sucks , trust me .😆 😆 😆
live and learn 🤣
How serious will it be if the cut-off was wrong? you get ticket just because of that?😕
1NZYaris1New Zealand · Oct 7, 2009#72
Originally Posted by JeremyG ↑
How serious will it be if the cut-off was wrong? you get ticket just because of that?😕
Ticket + Ordered of the road total fines about $500.NZ 😳
so it is not worth risking , but on the bright side , atleast
all i have to do is wait for the correct ones 👍
shouldn't be to far away , hopefully 😆
1NZYaris1New Zealand · Oct 11, 2009#73
does any one have any night shoots , of these projectors , showing cut off and glare 🤷 please.
Kaotic LazagnaCentral Valley, CA · Oct 11, 2009#74
I think Mike (camelll) had some. Glare was minimal and the cutoff was excellent.
PETERPOOPOahu · Oct 11, 2009#75
Originally Posted by 1NZYaris1 ↑
does any one have any night shoots , of these projectors , showing cut off and glare 🤷 please.
go to my liftback DIY for the projector headlights. I got night shots on page 2.
BrianThread starterRiverside, CA · Oct 11, 2009#76
Originally Posted by 1NZYaris1 ↑
does any one have any night shoots , of these projectors , showing cut off and glare 🤷 please.
1NZYaris1New Zealand · Oct 11, 2009#77
Thanks Brain , i had already copied that one , i was hoping to get one with both head lights lined up , your drivers side is way to low 👍
jounabayamon puerto rico · Oct 11, 2009#78
Picture lost · www.bjf2k.comPicture lost · www.bjf2k.com can these work??
BrianThread starterRiverside, CA · Oct 11, 2009#79
Originally Posted by 1NZYaris1 ↑
Thanks Brain , i had already copied that one , i was hoping to get one with both head lights lined up , your drivers side is way to low 👍
Its actually perfect while driving. High enough on the passenger side to light up road signs but low enough not to shine into peoples windows or mirrors.
1NZYaris1New Zealand · Oct 12, 2009#80
Thanks for that . just trying to show the suppliers that the cut off
does not suit right hand drive cars 👍
BrianThread starterRiverside, CA · Oct 12, 2009#81
Originally Posted by camelll ↑
Brian, you should adjust that drivers side, you will see a huge difference in the way the road lights up. I am surprised you got it to go that low without popping the adjustment screw out of the socket behind the reflector bowl. I did that on mine and I was not even close to that far down, I could not go any lower than the drivers side you see in the 4th pic and right below that I popped the adjuster screw out. Had to reopen the headlight and fix it, was kind of a pain in the butt.
I will lower the passenger side when I get a new set of headlights in a few months. I didn't want
to cut into the reflector housing at the time to lower it more. I was surprised too at how low they
came out.
1NZYaris1New Zealand · Oct 12, 2009#82
Originally Posted by camelll ↑
1nz the housings these projectors came in were RHD. The cutoff shield is for LHD but the RHD housings were rotated so the projectors shined up on the left. I don't know if yours is the same or not. It may be hard to understand what I am saying so I will post a pic of the cutoff in the RHD projectors and hope this helps.

The first pic, 3 black circles shows how the h4 grooves are rotated to the right allowing more light to shine on the left and less on the right. You can see the cutoff shield how it is angled. The shield is on the bottom but when the light comes out of the projector it is upside down. The housing was sitting flat for this pic.

2nd pic is the housing sitting flat so you can see how the cutoff would look in a RHD housing. This would probably work without blinding oncoming traffic but the proper way would be to have the cutoff shield going the opposite direction, I don't know if they make these or not. Would need to ask someone who has stock hid in RHD housing.

3rd pic is the same projector in a LHD housing, 3 black circles show how the h4 grooves are flat. It looks like it goes to the left but it is because the whole housing was rotated when I took the pic, but it is not rotated left or right. I hope this helps. If you have any more questions you can pm me or post in here if brian does not care.

Brian, you should adjust that drivers side, you will see a huge difference in the way the road lights up. I am surprised you got it to go that low without popping the adjustment screw out of the socket behind the reflector bowl. I did that on mine and I was not even close to that far down, I could not go any lower than the drivers side you see in the 4th pic and right below that I popped the adjuster screw out. Had to reopen the headlight and fix it, was kind of a pain in the butt.
Thanks for that Camel , but if i can't get the right cut off , then it's not worth the risk .
i do to much night driveing , to take short cuts on lighting ,
not to mention the fact it would not get a road worthy cert like that .
which it requires to pass every 12months .👍
JumpmanYarisSO. INDIANA · Oct 21, 2009#83
I started with my project..
JumpmanYarisSO. INDIANA · Oct 21, 2009#84
here it goes ..
102_0797.jpg102_0803.jpg
JumpmanYarisSO. INDIANA · Oct 21, 2009#85
Brian how did u get the projectors in the housing??😕
BrianThread starterRiverside, CA · Oct 21, 2009#86
Originally Posted by JumpmanYaris ↑
Brian how did u get the projectors in the housing??😕
After you remove the lens, the reflector and bulb clip it just slides right in.
JumpmanYarisSO. INDIANA · Oct 21, 2009#87
it aint sliding on on this one or am i doing something wrong
The reflector as in the crome part atached to the plastic housing?
JumpmanYarisSO. INDIANA · Oct 21, 2009#88
..
102_0806.jpg102_0805.jpg
JumpmanYarisSO. INDIANA · Oct 21, 2009#89
i think i have it now if i do i am gonna feel dumb
Red HorseCosta mesa, California · Oct 21, 2009#90
I realy like to do this, if only the projector is cheap.
JumpmanYarisSO. INDIANA · Oct 21, 2009#91
Doing some painting now
JumpmanYarisSO. INDIANA · Oct 21, 2009#92
painted projectors and crome parts I also sprayed some primer
102_0807.jpg102_0809.jpg
PETERPOOPOahu · Oct 21, 2009#93
hurry up jumpman. ;)

I believe you're the first one to actually paint the projectors? But the plastic is still on it?
BrianThread starterRiverside, CA · Oct 21, 2009#94
You may have to cut a piece out above the reflector so the projector doesn't hit it and so you can lower the cut off. You'll see when you go to put then back together. I see you didn't remove the rings before you tried to put the projector in.
JumpmanYarisSO. INDIANA · Oct 21, 2009#95
Originally Posted by Brian ↑
You may have to cut a piece out above the reflector so the projector doesn't hit it and so you can lower the cut off. You'll see when you go to put then back together. I see you didn't remove the rings before you tried to put the projector in.
Yeah I know I felt dumb lol, do I really need to do this even tho there is a bolt in the back to lower the light?
JumpmanYarisSO. INDIANA · Oct 21, 2009#96
Originally Posted by PETERPOOP ↑
hurry up jumpman. ;)

I believe you're the first one to actually paint the projectors? But the plastic is still on it?
Naa I think Brian did it as well I think it looks better so all u see is the light and the halo
PETERPOOPOahu · Oct 21, 2009#97
Originally Posted by JumpmanYaris ↑
Naa I think Brian did it as well I think it looks better so all u see is the light and the halo
Well actually, because the chrome on the projector is like a mirror, it actually reflects the black from the painted housing, and it looks like black chrome.
JumpmanYarisSO. INDIANA · Oct 21, 2009#98
mmm didnt think of that, but oh well i have em painted now then it shouldnt be a problem or i would think so. You should stick around so that you can help me with the electrical part of the project.
PETERPOOPOahu · Oct 21, 2009#99
that's the easiest part! i have to actually go to class and then get a new hi flow cat installed; so i won't be around. sorry! GL
JumpmanYarisSO. INDIANA · Oct 21, 2009#100
Originally Posted by PETERPOOP ↑
that's the easiest part! i have to actually go to class and then get a new hi flow cat installed; so i won't be around. sorry! GL
YOU SUCK!! Hopefully I'll get help from Brian if he sticks around😁