Yarisworld Archive

Wiper blades ....

82 posts · 52,114 views · page 2 of 2

Replies continued

jeff618Waterford, WI · Mar 28, 2010#51
Originally Posted by jeff618 ↑
(Too many wiper blade strings on this site but here we go again...)

OK...here's the ticket: The Toyota Yaris' 14" passenger side replacement windshield wiper is very hard to find in the newer-style beam blades. The 12" rear is also very hard to find because its a special rear blade that fits the special rear arm.

After exhaustive research, I've only found one aftermarket set-up that works: 'Trico NeoForm Beam Blades' on the front (yes, they have a 14") and 'Trico Exact Fit Rear Integral Blade' on the rear. All of the above come with step-by-step, illustrated removal and replacement instructions - easy install. Got the whole set-up online.
As a follow-up to my post above, I just got an email from wipers123.com and there's a $15 rebate on NeoForms (including the 14") through 5/15/10. They also sent me an additional $5 instant coupon "springreturningcustomer" (orders over $30) not sure when it expires... I'm not ready to replace mine yet so take it if you want it!

👍
dragoneyesPuerto Rico · Oct 7, 2010#52
Instead of using 26" drivers and 14" passenger, can I use 24" and 16". That is substracting 2 and adding 2. and this will avoid them hitting over each other at the bottom. But will cover less on the top while ON.

Just can't find the 14". And have a really nice offer. Buy one get one free on Goodyear wiper blades.
41magmag41New hampshire · Oct 7, 2010#53
15 inch blades work just fine on the passenger side. Simple fix.
2009BBPliftbackWestern PA (Franklin) · Oct 7, 2010#54
While I love the look of the Neoforms I don't like that they chatter alot they are very very noisy
jeff618Waterford, WI · Oct 8, 2010#55
Originally Posted by dragoneyes ↑
Instead of using 26" drivers and 14" passenger, can I use 24" and 16". That is substracting 2 and adding 2. and this will avoid them hitting over each other at the bottom. But will cover less on the top while ON.

Just can't find the 14". And have a really nice offer. Buy one get one free on Goodyear wiper blades.
If you're willing to upgrade...go Trico NeoForm which come in 14"

Originally Posted by 2009BBPliftback ↑
While I love the look of the Neoforms I don't like that they chatter alot they are very very noisy
Do they chatter in both directions or just one way? If one way, your wiper arm(s) may be twisted a little bit. The blades must be 90 degrees from the glass and when it chatters one way and not the other, that's a sign the wiper arm(s) may be twisted. I've have absolutely zero chatter with NeoForms.

Lastly - FYI - They are running the rebates again but this time are allowing two per household. In Spring they only allowed one. Rebate info here. 🎉

Happy Fall Everyone!!
kroloswa state · Oct 8, 2010#56
I changed out my stock wipers at around 35300 miles, I was surprized they
lasted that long, and they get alot of use here in the Pacific N.W., I
got my replacements at the Toyota Dealership , my Yaris just turned 36000 miles this morning and no problems🙂
Bmcguigan1Wilmington, NC · Aug 25, 2011#57
WOW! I contacted my local Toyota Dealer to get the replacement inserts for OEM blades and they told me they didnt have them in stock and wouldnt order them because the had to order too many to be worth it for them!
GanjaBabe420San Antonio, TX · Aug 26, 2011#58
Originally Posted by Bmcguigan1 ↑
WOW! I contacted my local Toyota Dealer to get the replacement inserts for OEM blades and they told me they didnt have them in stock and wouldnt order them because the had to order too many to be worth it for them!
Wow..that really sucks that they wouldn't order any for you..

I think I'm gonna go with the Bosch wiper blades that they have at Auto zone..
👍
thepartsmancomethmidwest · Aug 27, 2011#59
Originally Posted by Bmcguigan1 ↑
WOW! I contacted my local Toyota Dealer to get the replacement inserts for OEM blades and they told me they didnt have them in stock and wouldnt order them because the had to order too many to be worth it for them!
BS. Total BS. I work for a Toyota (and Ford) dealership in the parts dept. I can order 1 wiper insert, or 1 million. We don't even get a price break for ordering more. Why they don't want to do their job is beyond me.
jeff618Waterford, WI · Aug 28, 2011#60
Originally Posted by Bmcguigan1 ↑
WOW! I contacted my local Toyota Dealer to get the replacement inserts for OEM blades and they told me they didnt have them in stock and wouldnt order them because the had to order too many to be worth it for them!
I didn't switch to buying on line because of this type of thing, I switched because its so far of a drive and gas is so expensive. That said, your experience REALLY stinks. They obviously can't see the forest through the trees.

I still love the neoforms and its pretty cool that wipers123 sends me inspection reminders occasionallly so I always know how old my wipers are.
frog13Ohio · Nov 20, 2011#61
My original blades were awesome...16 months later had to replace them....replaced them with Toyota blades......not impressed....definetly not the same that came from the factory!!!!....just like tires etc. .
A-Dingo-Ate-My-Babyearth · Nov 20, 2011#62
Originally Posted by jeff618 ↑
If you're willing to upgrade...go Trico NeoForm which come in 14"



Do they chatter in both directions or just one way? If one way, your wiper arm(s) may be twisted a little bit. The blades must be 90 degrees from the glass and when it chatters one way and not the other, that's a sign the wiper arm(s) may be twisted. I've have absolutely zero chatter with NeoForms.

Lastly - FYI - They are running the rebates again but this time are allowing two per household. In Spring they only allowed one. Rebate info here. 🎉

Happy Fall Everyone!!
Trico make a NeoForm exact replacement for the rear, additional plastic housing and special connector clip and all, just like the OEM. Yank old blade and housing all the way backward and it pops off a small clip.
ShroomsterOrlando · Nov 21, 2011#63
I've had the same pair of silicone triple edge wiper blades on my civic for about 7 years I think.....give or take a year or two each way......just got to clean them every few months. The suspension arms are sun oxidizing but they are still holding up......
jeff618Waterford, WI · Nov 21, 2011#64
Originally Posted by A-Dingo-Ate-My-Baby ↑
Trico make a NeoForm exact replacement for the rear, additional plastic housing and special connector clip and all, just like the OEM. Yank old blade and housing all the way backward and it pops off a small clip.
I can't find a rear neoform but I use their exact fit rear for the yaris: https://www.wipers123.com/detailed_p...?products_id=8

Install Video (Click xx-A): https://www.wipers123.com/wiper_blad...ion_videos.php
A-Dingo-Ate-My-Babyearth · Nov 21, 2011#65
oops ^ yeah I dun goofed, call the cyberpolice. that is what I meant. exact fit, same rubber but not a 'neoform'
Still LearningLansing, MI · Nov 21, 2011#66
I used neoforms on my minivan last winter. They are awesome wipers. I just ordered a set for the Yaris. I highly recommend them.
A-Dingo-Ate-My-Babyearth · Nov 22, 2011#67
.
..
...update

not 100% happy with the new Trico exact fit rear for the yaris HB
(the fronts are fine)

the rear loses traction at the tip furthest from the arm,
in the first 4 inches of wipe, from .1 to 1 inch to .1 inch wide.

failsauce. I have a peeve and it is any rear wiper with less than 100% contact.

I will need to regroup and try a new arm, or a new insert, or something
to calm my seething rage.
jeff618Waterford, WI · Nov 22, 2011#68
Originally Posted by A-Dingo-Ate-My-Baby ↑
oops ^ yeah I dun goofed, call the cyberpolice. that is what I meant. exact fit, same rubber but not a 'neoform'
No problem - lol

Originally Posted by Still Learning ↑
I used neoforms on my minivan last winter. They are awesome wipers. I just ordered a set for the Yaris. I highly recommend them.
Pretty quiet, hey?

Originally Posted by A-Dingo-Ate-My-Baby ↑
.
..
...update

not 100% happy with the new Trico exact fit rear for the yaris HB
(the fronts are fine)

the rear loses traction at the tip furthest from the arm,
in the first 4 inches of wipe, from .1 to 1 inch to .1 inch wide.

failsauce. I have a peeve and it is any rear wiper with less than 100% contact.

I will need to regroup and try a new arm, or a new insert, or something
to calm my seething rage.
Sounds like you got a bad one or that the wiper is binding slightly on the arm or the arm is getting tight at the hinge. Make sure to carefully lubercate the wiper arm hinge and that the wiper blade moves freely. If you still have the problem after that...you got a bad blade.
Still LearningLansing, MI · Nov 22, 2011#69
Originally Posted by Still Learning
I used neoforms on my minivan last winter. They are awesome wipers. I just ordered a set for the Yaris. I highly recommend them.

Pretty quiet, hey?

Yeah, very quiet. No squeaking noise at all.
A-Dingo-Ate-My-Babyearth · Nov 22, 2011#70
figured out the rear Trico exact fit problem:

The Trico exact-fit replica wiper blade housing is close, but not exactly the same
as the OEM. The length stop-to-stop is 3mm longer. The Trico insert has some
wiggle room side-to-side, allowing the far-end of the insert to float off the glass
when pressure is applied to the middle of the insert

I slid the Trico insert out of the Trico arm, installed the Toyota arm, and slid in the
Trico insert. The Toyota stop tabs touch the insert at both ends of the blade, and when
the arm is at rest position, the stops hold the insert and keep it from floating off the glass.

So, in the case of: should I get a new insert, or a whole new Trico exact fit assembly ?
say NO to Trico, or just get the insert.

Other companies may make a better OEM-fit blade housing, but Trico dropped the ball on this one.

I now have 100% rear wiper contact. crisis averted.
YuryCanada · Nov 22, 2011#71
Originally Posted by A-Dingo-Ate-My-Baby ↑
.
..
...update

not 100% happy with the new Trico exact fit rear for the yaris HB
(the fronts are fine)

the rear loses traction at the tip furthest from the arm,
in the first 4 inches of wipe, from .1 to 1 inch to .1 inch wide.

failsauce. I have a peeve and it is any rear wiper with less than 100% contact.

I will need to regroup and try a new arm, or a new insert, or something
to calm my seething rage.
trickos don't really work of the rear. i had the same issue, bought the whole blade from toyota, seems to work nicely. 10$ and you can change just the rubber from that point on. just keep the toyota blade.
YuryCanada · Nov 22, 2011#72
Originally Posted by A-Dingo-Ate-My-Baby ↑
figured out the rear Trico exact fit problem:

The Trico exact-fit replica wiper blade housing is close, but not exactly the same
as the OEM. The length stop-to-stop is 3mm longer. The Trico insert has some
wiggle room side-to-side, allowing the far-end of the insert to float off the glass
when pressure is applied to the middle of the insert

I slid the Trico insert out of the Trico arm, installed the Toyota arm, and slid in the
Trico insert. The Toyota stop tabs touch the insert at both ends of the blade, and when
the arm is at rest position, the stops hold the insert and keep it from floating off the glass.

So, in the case of: should I get a new insert, or a whole new Trico exact fit assembly ?
say NO to Trico, or just get the insert.

Other companies may make a better OEM-fit blade housing, but Trico dropped the ball on this one.

I now have 100% rear wiper contact. crisis averted.
may ask why not buy the toyota blade? doesn't seem expensive and you can replace the just rubber after.
A-Dingo-Ate-My-Babyearth · Nov 22, 2011#73
Originally Posted by Yury ↑
may ask why not buy the toyota blade? doesn't seem expensive and you can replace the just rubber after.
I was on a mission to buy bundles of blades as presents
for everyone (dropped 380 bucks) and I figured I would also
try a trico exact fit.

This is my time to test a new batch of blades
[Just got done testing Michelins, RainXbrand, and Tripledge last 3 years]



so I went with Trico NeoForm on my Yaris, Trico exact fit (not so exact) rear.
and AquaPel as a surface coating (RainX only on side and back windows)

PIAA silicones on my 4runner and OEM rear insert, with RainX

and Silblade silicone for my GF, and sister gets PIAA's, with RainX

these silicone blades are not cheap

and I do not want to test AquaPel with Silicone blades. I need to test
with old-school Trico blades to know what Aquapel really does or does not do
this winter
Still LearningLansing, MI · Nov 22, 2011#74
Originally Posted by A-Dingo-Ate-My-Baby ↑
figured out the rear Trico exact fit problem:

The Trico exact-fit replica wiper blade housing is close, but not exactly the same
as the OEM. The length stop-to-stop is 3mm longer. The Trico insert has some
wiggle room side-to-side, allowing the far-end of the insert to float off the glass
when pressure is applied to the middle of the insert

I slid the Trico insert out of the Trico arm, installed the Toyota arm, and slid in the
Trico insert. The Toyota stop tabs touch the insert at both ends of the blade, and when
the arm is at rest position, the stops hold the insert and keep it from floating off the glass.

So, in the case of: should I get a new insert, or a whole new Trico exact fit assembly ?
say NO to Trico, or just get the insert.

Other companies may make a better OEM-fit blade housing, but Trico dropped the ball on this one.

I now have 100% rear wiper contact. crisis averted.
This is good info. Thanks.
YuryCanada · Nov 22, 2011#75
"...housing, but Trico dropped the ball on this one."

wouldn't be the first time. same issue on my old car, the curvature of the rear glass was not matched by Trico (and other aftermarket brands). the only remedy was to use the factory backing (the metal insert) which was bent correctly to conform. same story on Yaris...the blades look almost the same but definitely are not the same.
10 FrancisTexas · Nov 26, 2011#76
Any Toyota part number that has "YZZ" in it may be a "Toyota Genuine Part", but it's not a factory part. it's common for wipers, oil filters, cabin filters, and some other fast-moving parts. We (the dealership) sell these because they're less expensive for us, and for our customers, and they're still high-quality parts that are approved by Toyota. I'll post a list soon of wiper blade part numbers for Yari.
10 FrancisTexas · Nov 26, 2011#77
'06-'11 TCMC
Blades:
driver: 85222-YZZ18-TM (650mm ~25.6")
passenger: 85212-YZZ14-TM (350mm ~13.8")
the inserts for these blades cannot be replaced. the whole blade must be changed.
Inserts (for factory blades):
driver: 85214-YZZF1-TM
passenger: 85214-YZZF3-TM
TCMC does not offer blades or inserts for the rear (HB)

'06-'11 Factory
Blades
driver: 85222-47020
passenger: 85212-44032
rear: 85242-52040
Inserts
driver: 85214-44140
passenger: 85214-68011
rear: 85214-31010
10 FrancisTexas · Nov 26, 2011#78
oh yeah...
'12 Factory
Blades
front: 85222-52210
rear: 85242-42030
Inserts
front: 85214-58030
rear: 85214-42040

I haven't seen any TCMC blades or inserts listed for the '12 (yet)
jeff618Waterford, WI · Nov 27, 2011#79
I must have lucked out with my trico rear blade...its not perfect, but its about the same as the factory. Irregardless I still love the neoforms on the front - the crappy weather in Wisconsin the last 3 days has proved that over and over to me. Happy Thanksgiving ya'll.
ShroomsterOrlando · Dec 2, 2011#80
Originally Posted by A-Dingo-Ate-My-Baby ↑
I was on a mission to buy bundles of blades as presents
for everyone (dropped 380 bucks) and I figured I would also
try a trico exact fit.

This is my time to test a new batch of blades
[Just got done testing Michelins, RainXbrand, and Tripledge last 3 years]



so I went with Trico NeoForm on my Yaris, Trico exact fit (not so exact) rear.
and AquaPel as a surface coating (RainX only on side and back windows)

PIAA silicones on my 4runner and OEM rear insert, with RainX

and Silblade silicone for my GF, and sister gets PIAA's, with RainX

these silicone blades are not cheap

and I do not want to test AquaPel with Silicone blades. I need to test
with old-school Trico blades to know what Aquapel really does or does not do
this winter
You tried all those brands you listed over the last three years (is that how I should read that statement?)

If so, I take it none of them lived up to your expectations? Hence your high regard for trico?
Perpetuous_DreamerOxford, Ohio · Dec 3, 2011#81
A little advice: don't buy wiper blades from NAPA!!! They are the worst investment in my car I ever made. Threw them in garbage next day due to the loss of receipt and went back to Toyota's OEM ones.
jeff618Waterford, WI · Feb 2, 2012#82
I've been trying to buy a new set of neoform beam blades for the front since my last post and the 14" passenger side has been out of stock nationally all fall and winter. I just got an email from wipers123 and they're back in stock. Just thought I'd share because its one of the only 14" beam blades available for the yaris.