Yarisworld Archive

Megan Header Install [pics]

126 posts · 108,841 views · page 2 of 3

Replies continued

ism3tSouthern California · Dec 21, 2006#51
no one else hearing a kind of sputterin noise? or similar to a lawn mower or car kart when they accel?
Chris07LBThread starterNew Jersey · Dec 21, 2006#52
Originally Posted by ism3t ↑
no one else hearing a kind of sputterin noise? or similar to a lawn mower or car kart when they accel?
If your hearing that, you have a leak somewhere.. either at the collector, or the header gasket.
mikeukrainetzCanada · Dec 21, 2006#53
why the specialty tools? why not use a breaker bar? its like 20 bucks at any parts store.
Chris07LBThread starterNew Jersey · Dec 21, 2006#54
Didn't think what I listed in my parts list, was anything special. Its a DIY ment to "help" in the install process, its not the bible on one way of doing something.

Depending on how high you can get your car off the ground (without a lift), its going to be hard to spin a breaker bar, with the limited amount or room you will have under the car. Everyone's different though, whatever works.
ChinoCharlesOH · Dec 21, 2006#55
Somehow that adapter made it here in two days, so I finally started getting bolts off today. Got the collector bolts, the lower mount, and a few of the block bolts. Those fuckers are a PITA! Tight spaces everywhere!

Hey Chris or whoever else, how do you unplug the O2 sensor?
Chris07LBThread starterNew Jersey · Dec 21, 2006#56
Unplugging is simple. There will be a smallish tab to depress, then pull the halfs apart. I know its a bit hard to see it while your doing it, so you kinda just have to go by feel. Once its unplugged, you will relise how very simple it was. 🙂
graywolf_14Wichita ks · Dec 22, 2006#57
If you are wanting results than do exhuast aswell. A header or exhuast will give u minimal results unless doing them both.
graywolf_14Wichita ks · Dec 22, 2006#58
And as for feeling a difference with 5hp you really can. I put a k&n filter and removed my silencer on my dsm and could notice it. I than later removed my air box and could really notice a difference on the highway.
jimcatHong Kong · Dec 22, 2006#59
Originally Posted by Chris07LB ↑
Actually, yes. The car seems much smoother to drive the entire powerband.
No real increase in sound with my stock exhaust, but it does feel a bit stronger when crusing at 65mph, then hitting the gas to pass a car.

Smooth, smooth is the best way I can describe it.. no laboring to get thru the gears.
make a wish if i have one
ChinoCharlesOH · Dec 24, 2006#60
FINALLLLYYYYYYYYY got it on.

Before you go asking "dude what the fuck took you so long" allow me to tell you. I had never performed a mod like this before, and every single nut and bolt and harness along the way was a new challenge, but in the end I can say I did it myself and I am now a little less wrenchtarded than I was before!

Thanks to riceboy for organizing the group buy, and a special thanks to Chris for writing the DIY and taking time out of his day to talk me through some of the more stressful parts of the install. There is absolutely NO WAY I could have done this right without you dude.

After driving around on it, I can officially say the car does not seem any faster during heavy loads, although I know by some minute fraction of a second it likely is. While driving normally, however, it felt like the engine had to labor a LOT less to get the car moving. Chris nailed it on the head... everything is just a little smoother now. There is also a nice little whoosh coming from the engine bay that wasn't there before. Overall, I'm stoked with the outcome, but I'm not done with this exhaust just yet! I'll have pictures of a new toy soon. Santa needs to get his ass here NOW!

A point of interest on the DIY... I had a lot more luck using a deep well 12mm socket on the two nuts holding the header to the block than I did using a 12mm box wrench. Actually I stripped them a tad with the box wrench and will be replacing them next week... hehe. Either way, that DIY was spot on. If you're like me and are just getting into modding four bangers, this is a good mod to start with to get your feet wet, and at a really reasonable price as well.

The holidays are screwing up my dyno situation, so everyone be patient. We will have results soon.

I'm going to go bandage my knuckles now. 😁
graywolf_14Wichita ks · Dec 24, 2006#62
That is a really great deal, was that with the group buy or is that just what anyone would pay?
ChinoCharlesOH · Dec 24, 2006#63
That is the new public price. The group buy price was $190 shipped... 15 bucks under MSRP!
graywolf_14Wichita ks · Dec 24, 2006#64
Yeah but 205 is still a great price. Seeming that the only thing you could posibly get cheaper is a pacesetter.
03Z33SoCal · Dec 24, 2006#65
Congratulations on the install Charles! I may have missed it, but did you already dyno your car stock, for a baseline?
ChinoCharlesOH · Dec 24, 2006#66
I didn't. Since I had never done anything like this before, I had to install the new part first. Now that I know what I am dealing with, I get to take the new part off, put the old one back off, and then do it all over again! FUN! Hehe.
03Z33SoCal · Dec 24, 2006#67
Makes good sense 😉 This way you should get pretty reliable numbers 👍
dngzvancouver · Dec 24, 2006#68
with intake, header, and 2" catback exhaust, the gain i felt was huuuge!! my fuel economy also improved quite noticeably!
ChinoCharlesOH · Dec 25, 2006#69
As promised...

SAY HELLO TO MY LITTLE FRIEND!

Picture not included in this copy
Picture not included in this copy
Picture not included in this copy

$140 or so shipped. Megan's M-DF muffler, dual 3.5" tips with silencers.

3 attachments not included in this copy

Chris07LBThread starterNew Jersey · Dec 25, 2006#70
😈 Merry Christmas fella's... Charles, got your PMs but just work up and about to have dinner.. ill write you laterz.
ChinoCharlesOH · Dec 25, 2006#71
Just woke up, about to have dinner. LOL you fucking champ. Take your time, I'll be out till tomorrow evening.
BokChoiSophia, WV · Mar 21, 2007#72
just got done installing but have a quick question... is the heat shield suppose to be put back on the new header?
joey1320Lakewood, Ohio · Mar 21, 2007#73
Originally Posted by ChinoCharles ↑
As promised...

SAY HELLO TO MY LITTLE FRIEND!

Attachment 2612
Attachment 2613
Attachment 2614

$140 or so shipped. Megan's M-DF muffler, dual 3.5" tips with silencers.


are you really plaining on using that for your car???
wow! I had something similar on my CRX before and it sounded horrible, good luck!
ChinoCharlesOH · Mar 22, 2007#74
Since I bought it I have come to the realization this thing is WAY too big for a Yaris.

It is for sale if anyone is interested.
Chris07LBThread starterNew Jersey · Mar 22, 2007#75
Originally Posted by BokChoi ↑
just got done installing but have a quick question... is the heat shield suppose to be put back on the new header?

NO. 👎

Notice the picture doesnt have it....
BokChoiSophia, WV · Mar 22, 2007#76
cool thanks
jamal1984Georgia, USA · Mar 26, 2007#77
Originally Posted by BokChoi ↑
just got done installing but have a quick question... is the heat shield suppose to be put back on the new header?
Originally Posted by Chris07LB ↑
NO. 👎

Notice the picture doesnt have it....
if we don't put the heat shield back to the megan header, does the heat temperature will kill the engine?
Chris07LBThread starterNew Jersey · Mar 26, 2007#78
A thin soda can thick heat shield does nothing for the engine, its to help keep the skin on your fingers for retards that feel the need to poke around a hot engine bay without knowing.
jamal1984Georgia, USA · Mar 26, 2007#79
thanks Chriss
Chris07LBThread starterNew Jersey · Mar 26, 2007#80
👍
d4w1Fort Worth · Apr 11, 2007#81
I have purchased and installed the same header. Except that the exhaust bolts and studs are too short. The correct size you need is 8mm x 1.25 x 30mm. Mr Gasket sell this correct hardware.
Chris07LBThread starterNew Jersey · Apr 12, 2007#82
Originally Posted by d4w1 ↑
I have purchased and installed the same header. Except that the exhaust bolts and studs are too short. The correct size you need is 8mm x 1.25 x 30mm. Mr Gasket sell this correct hardware.
If you were given hardware OTHER then what is pictured / noted in my post, which Im guessing you did... otherwise, whats included is perfect.
cali yarisCanoga Park, CA · May 28, 2007#83
Now to the question, that Megan header looks pretty much exactly like the stock one from the pics. Are the interior surfaces and joints just smoother? What does Megan say the specific difference is? .. thanks...
Black YarisToledo, OH · May 28, 2007#84
it is much larger diameter piping, and a much thicker flange
tk-421Dagobah · May 28, 2007#85
Another question: Does this mod really do anything for performance? I've already read a few posts denying this.
Black YarisToledo, OH · May 28, 2007#86
you get the HP in the higher RPM range, you need to do more mods like; the rest of the exhust and a good intake to get the full effect of the header
Chris07LBThread starterNew Jersey · May 28, 2007#87
Look at the pics again.. there is a night in day difference from the "look" of the stock pea shooter, compared to the Megan.
cali yarisCanoga Park, CA · May 28, 2007#88
sounds like a worthwhile mod overall. thanks for the DIY post and subsequent tips on installation. I'm glad it's not that much louder (if at all?), that would make me hesitate to do this.
Yaris OmegaThe Ark "Wake Me When You Need Me" · May 29, 2007#89
yo chris whats your next project for your yaris
Chris07LBThread starterNew Jersey · May 29, 2007#90
Originally Posted by Yaris Omega ↑
yo chris whats your next project for your yaris
Well being this is still just my work beater car, I'll still being doing more upgrades as I work with a few places putting out some fresh new products to test. Keep an eye out for some pretty cool shit this summer from me. 😎
BlenjarCT · Jun 24, 2007#91
I might buy one next week since it helps in mid and higher RPM..which is what I need for my daily highway driving.

-- Blen
tk-421Dagobah · Jun 24, 2007#92
I'm still waiting on a 4-2-1 header to come out.
I've heard from a reliable source that it might be in the works as we speak... 😲
Chris07LBThread starterNew Jersey · Jun 25, 2007#94
Weapon R has my stock header for months now.. i guessing they will have their 4-2-1 complete and on the market shortly.
cali yarisCanoga Park, CA · Jun 27, 2007#95
OK, so I got my Megan header on today.

1. It's a lot louder.
2. It "feels" like there is more mid-range pull.
3. It really is louder.

As soon as I have enough miles on my car, I'm going to do a few dyno pulls to see where she's at.
whooppee777Maryland · Jun 27, 2007#96
what should the bolts be torqued to? i just ordered my headers today. cant wait!🤘
BlackMan_InkCerritos, CA · Aug 13, 2007#97
Originally Posted by ChinoCharles ↑
OK, so I know you guys are wondering where the fuck the dyno results are.

Sunday rolls around and I pop open the install DIY and see that I need a 3/4 inch drive ratchet. Well, I decide I am going to try and torque those bolts off with a 1/2 inch drive, because I had honestly never seen a 3/4 inch ratchet and wasn't convinced I could easily find one. Took the heat shield off, got the car up on stands, and crawl under there... not happening. Chris wasn't kidding. You need some serious leverage for those collector bolts, as they are torqued to 32 lb/ft. Well, I go out and find a 3/4 inch drive ratchet at Autozone (surprisingly) but they don't sell any adapters or sockets for it. I then tried Sears hardware, regular Sears, Advanced Autoparts, Lowes, and Home Depot. Nothing. Called the dyno shop to see if he had one sitting around, and that was a big fat no. I was shit outta luck. So, I ordered a 3/4 inch female to 1/2 inch male adapter from Amazon.com and upon reception of that (should be here soon after Christmas) I will install the new header and go to the dyno shop.

Sorry for the teaser... of course the one tool I need seems to be a tool that you can't get without dropping thousands on a master mechanic's toolbox. God dammit. I'll update when I get the adapter and get the new header on. Sorry guys!

On the bright side, I now have a ratchet big enough to kill a large individual.
Chinocharles how much was the 3/4 to 1/2 connector piece?...I'm having the same problem getting the bolt off the bracket...all the other bolts came off easy but there's no room in the damn compartment to move the ratchet and hold the wrench to the nut on the other side of the bracket...plz help another noob mechanic.
NabiscoTampa · Aug 13, 2007#98
I really don't mean to pee in anyone's Wheaties but I would rather pay more for the TRD unit, or one from a real manufacturer. Megan stuff is designed to make money not power. I have seen several of their manifolds fail. It is cheap mass produced Chinese merchandise.
BlackMan_InkCerritos, CA · Aug 13, 2007#99
Originally Posted by Nabisco ↑
I really don't mean to pee in anyone's Wheaties but I would rather pay more for the TRD unit, or one from a real manufacturer. Megan stuff is designed to make money not power. I have seen several of their manifolds fail. It is cheap mass produced Chinese merchandise.
Fail how? Does TRD make a manifold for the Yaris?
Chris07LBThread starterNew Jersey · Aug 13, 2007#100
Originally Posted by BlackMan_Ink ↑
Chinocharles how much was the 3/4 to 1/2 connector piece?...I'm having the same problem getting the bolt off the bracket...all the other bolts came off easy but there's no room in the damn compartment to move the ratchet and hold the wrench to the nut on the other side of the bracket...plz help another noob mechanic.
Home Depot or Lowes will have them for around 5 bucks.