Yarisworld Archive

Basic Intake installed

99 posts · 21,610 views · page 1 of 2

spkrmanOriginal post2 · Nov 26, 2006#1
APC filter, a little 3" PVC, and for right now a little duct tape :)

Definitely a big gain on the top end... up until now I've never gotten the car up to 110, last night I did it twice, and it took about the same amount of time as it took to get to 103-105 before.

When I first swapped, the car ran like ass, didn't wanna idle and threw up a check engine light. It was way low on torque too.

Disconnected battery, reconnected... the torque came back, and no more codes :). Also sounds awesome! Still seems like there is less torque than before, but once it gets higher in the RPM range it really pulls, as to where before it was just pretty even.... when it upshifts I can really feel the loss in power - was much "smoother" before, but definitely less top end.

I may spring for an AEM filter, I've had this APC filter before and its not exactly the cats meow, serves its purpose for a few months but just doesn't last.

The filter is tucked right next to the drivers headlight. There is a short length of 3" PVC to where the MAF plugs into, then the 3" pvc is coupled with the stock tubing from that point. Works great, very happy with the results!

Replies 98

spkrmanThread starter2 · Nov 26, 2006#2
damit put this in the wrong forum, not sure how i managed that lol...
eTiMaGoBangkok, Thailand · Nov 26, 2006#3
pictuuuuuuures.... pictuuuuuuuuuuuuures....
YarisPRMayaWest, Puerto Rico · Nov 26, 2006#4
Chris07LBNew Jersey · Nov 26, 2006#5
How big did you go on the tubing (I.D.)? That would explain your low end loss, if too big.
spkrmanThread starter2 · Nov 26, 2006#6
Originally Posted by Chris07LB
How big did you go on the tubing (I.D.)? That would explain your low end loss, if too big.
3" PVC to the stock piping, I think i'll replace it all with ABS later - I wussed out on PVC'n the whole thing since the TB is right next to the motor... hot day idling in traffic... PVC does have its limits :)

its nothin too sexy right now lol, but I'll snap up some pics later today, along with taking it out for a spin.
Black YarisToledo, OH · Nov 26, 2006#7
no offence, but ain't this a bit much of a hack job for new car?
vodkalushRochester, NY · Nov 26, 2006#8
well we cant really tell till we get some pics 🙄
ecoAtlanta · Nov 26, 2006#9
No Black,because PVC is actually a better material,and withe the right stuff,it will look like a million bucks.
Notthy[Yaris/S]07Puerto Rico · Nov 27, 2006#10
yeah put pics to see the project men
spkrmanThread starter2 · Nov 27, 2006#11
Originally Posted by Black Yaris
no offence, but ain't this a bit much of a hack job for new car?
Its more of a tester than anything - which, the car really responds well to an intake :)

but ya its kinda ugly now lol

New or old, doesnt really matter, the stock box can go back on at any time if need be.

Put some premium mobile in there which seemed to boost the top end even more, had BP regular in there before.

Even with all the racing/fast driving... still averaged 32mpg lol.
vodkalushRochester, NY · Nov 27, 2006#12
cough cough... pics... cough cough
spkrmanThread starter2 · Nov 27, 2006#13
hehe ok, i'll get some pics later :)

I'm tryin to figure if I can PVC all the way to the TB... it doesn't seem to get so hot, but then again its cool outside. Any ideas there?
mikeukrainetzCanada · Nov 27, 2006#14
PVC should be fine, you can drain boiling water through it, just dont make it out of the white stuff with the bright yellow glue all over it... lol.
Anyway, I posted it up earlier but Iceman intakes uses the same material just because it handles temperature change much better than thin wall aluminum tube.
spkrmanThread starter2 · Nov 28, 2006#15
Originally Posted by mikeukrainetz
PVC should be fine, you can drain boiling water through it, just dont make it out of the white stuff with the bright yellow glue all over it... lol.
Anyway, I posted it up earlier but Iceman intakes uses the same material just because it handles temperature change much better than thin wall aluminum tube.
yea I let the car idle today when it was warmer, the TB didn't get anywhere close to near hot enough to start the PVC melting.

It doesnt look like the TV will mate up with 3" PVC, so I will probably have to mold the 3" stuff to fit it. A template made from the TB and enough heat, shouldnt be too hard. An adapter would be easier, duno I'll have to take it apart and measure.
KSIbuckyFond du Lac, WI · Nov 28, 2006#16
Originally Posted by YarisPR
spkrmanThread starter2 · Nov 28, 2006#17
x10000000000000000000 pics are on the way i'm uploading nowlol
spkrmanThread starter2 · Nov 28, 2006#18
I wanted to keep the $ as low as possible, and make returning to stock as easy as possible before I invested on an intake... I figured it would be worth it, but better safe than sorry!

Its an APC filter from autozone, now that I see the results with this one, when I rebuild the intake I'll trade this one up for an AEM.

My major issue is mounting the MAF??? Any suggestions? I poked around home depot for at least an hour, and I couldnt find anything entirely suitable to securely mount it. Right now I just drilled a hole in the PVC and jammed it in there, its not even a good seal as it stands, hence the duct tape.

Total cost, approx $35, being generous :)

Picture not included in this copy

Awesome results! The top speed is something that I can put a number on, before it was a struggle to get past 105, directly after, 110 took about the same amount of time. With a switch to mobil premium gas, I got it up to 115 today on the same stretch I got to 110 on last time and couldnt get past 105 on before (i had actually tried for longer distances to get past 105 on the stock setup), between 2 highway exits, they are approx (using mapquest map) 1.5 miles apart. Approx 1-1.25 mile to get up to 115 :).

Other than that, its tough to say exactly what it did. It "feels" faster, and I can without a doubt feel the extra kick in the top end.

I earlier posted about a loss of torque, but after driving it around some more... i think it might just br the big boost in the top end making it "feel" weaker down low.

I also have a magnaflow muffler on the stock piping, and it really didnt do much, but I think combined with the intake it made a big difference.

For its purposes, even my ugly/cheap/ghetto setup works great - the biggest difference is passing on the highway, its alot easier now.

I plan to redo it out of one solid piece of PVC and paint it. I've bent PVC before and all it takes is a good amount of heat.
mikeukrainetzCanada · Nov 28, 2006#19
Im not bashing at all cause I tried the same damn thing with whatever I could find at home depot... that was over winter last year. That MAF sensor location is a real POS, molded into the box, not like everything else. I tried moulding a mount with Fiberglass over the PVC but got a little too liberal with the Fiberglass, its a great option if you got the time and patience.

The ONLY place ive seen an adapter for this type of MAF sensor was in MAX Power magazine from the UK. A company called Pipercross (who actually direct ship to Canada and the US) has a kit for the Corolla that comes with the adapter. Ive contacted them regarding buying the adapter seperate of the kit but got no response. You can try their website here
http://www.pipercrossdirect.com/sear...yota&x=30&y=12

Vibrant in Canada also has a 3" ID to 2" ID silicone reducer that would work perfect for this and its $12 Can.

Im also in the process of building my own intake using an old kit I had lying around for my old Neon. I need to setup the MAF sensor mount in CAD and drop it off at the CNC shop here and itll be done, but its been cold and Im too friggin lazy at this point.
I should actually price this out if anyone is interested in getting one. Either a stand-alone mount or welded to a 2.5-3" aluminum tube.

Excellent job in the ingenuity department btw! Im all for 'build it yourself'

Please post up any progress...
spkrmanThread starter2 · Nov 28, 2006#21
Originally Posted by mikeukrainetz
Im not bashing at all cause I tried the same damn thing with whatever I could find at home depot... that was over winter last year. That MAF sensor location is a real POS, molded into the box, not like everything else. I tried moulding a mount with Fiberglass over the PVC but got a little too liberal with the Fiberglass, its a great option if you got the time and patience.

The ONLY place ive seen an adapter for this type of MAF sensor was in MAX Power magazine from the UK. A company called Pipercross (who actually direct ship to Canada and the US) has a kit for the Corolla that comes with the adapter. Ive contacted them regarding buying the adapter seperate of the kit but got no response. You can try their website here
http://www.pipercrossdirect.com/sear...yota&x=30&y=12

Vibrant in Canada also has a 3" ID to 2" ID silicone reducer that would work perfect for this and its $12 Can.

Im also in the process of building my own intake using an old kit I had lying around for my old Neon. I need to setup the MAF sensor mount in CAD and drop it off at the CNC shop here and itll be done, but its been cold and Im too friggin lazy at this point.
I should actually price this out if anyone is interested in getting one. Either a stand-alone mount or welded to a 2.5-3" aluminum tube.

Excellent job in the ingenuity department btw! Im all for 'build it yourself'

Please post up any progress...
I think I have a good idea on how to mount the MAF properly just using a short piece of piping mounted into the PVC, and tapered on the inside so that it doesnt stick out into the way of airflow.

What is "vibrant"? Should be 3" to 2.5" correct? The readily available 3" rubber coupler will compress down around the 2.5" MAF, I think, but I'm just not sure if I would have full confidence in the seal.

I think the next step with the next revision willbe to remove the old airbox bracket and get the intake down there, the pipe shouldnt be too long, and the bend shouldnt be too harsh. The design I have in my head at least would make it seem pretty easy :)

Yea I'm definitely a DIY guy! Its much more fun to DIY, and in the end it may take more work to achieve your goals, but getting there is all the fun :)
mikeukrainetzCanada · Nov 28, 2006#22
Vibrant is a canadian parts company dealing mostly in exhaust and intercoolers and associated parts. They have great products and people.

http://www.vibrantperformance.com/

As far as the reducer you may want to actually measure it, I bought a 2.5" (might have been 2.25") reducer and it was quite a bit too large for the TB.

Maybe I could post pics of my setup as it sits on the basement floor....
Notthy[Yaris/S]07Puerto Rico · Nov 28, 2006#23
Originally Posted by spkrman
I wanted to keep the $ as low as possible, and make returning to stock as easy as possible before I invested on an intake... I figured it would be worth it, but better safe than sorry!

Its an APC filter from autozone, now that I see the results with this one, when I rebuild the intake I'll trade this one up for an AEM.

My major issue is mounting the MAF??? Any suggestions? I poked around home depot for at least an hour, and I couldnt find anything entirely suitable to securely mount it. Right now I just drilled a hole in the PVC and jammed it in there, its not even a good seal as it stands, hence the duct tape.

Total cost, approx $35, being generous :)

Picture not included in this copy

Awesome results! The top speed is something that I can put a number on, before it was a struggle to get past 105, directly after, 110 took about the same amount of time. With a switch to mobil premium gas, I got it up to 115 today on the same stretch I got to 110 on last time and couldnt get past 105 on before (i had actually tried for longer distances to get past 105 on the stock setup), between 2 highway exits, they are approx (using mapquest map) 1.5 miles apart. Approx 1-1.25 mile to get up to 115 :).

Other than that, its tough to say exactly what it did. It "feels" faster, and I can without a doubt feel the extra kick in the top end.

I earlier posted about a loss of torque, but after driving it around some more... i think it might just br the big boost in the top end making it "feel" weaker down low.

I also have a magnaflow muffler on the stock piping, and it really didnt do much, but I think combined with the intake it made a big difference.

For its purposes, even my ugly/cheap/ghetto setup works great - the biggest difference is passing on the highway, its alot easier now.

I plan to redo it out of one solid piece of PVC and paint it. I've bent PVC before and all it takes is a good amount of heat.


Looks Awsome and its a great idea i think make that job
KatanaUnder the hood! · Nov 28, 2006#24
Looks nice.
YarisPRMayaWest, Puerto Rico · Nov 28, 2006#25
Originally Posted by Notthy[Yaris/S]07
Looks Awsome and its a great idea i think make that job
me avisas cuando lo hagas pq toy loko por uno👍
spkrmanThread starter2 · Nov 28, 2006#26
Originally Posted by mikeukrainetz
Vibrant is a canadian parts company dealing mostly in exhaust and intercoolers and associated parts. They have great products and people.

http://www.vibrantperformance.com/

As far as the reducer you may want to actually measure it, I bought a 2.5" (might have been 2.25") reducer and it was quite a bit too large for the TB.

Maybe I could post pics of my setup as it sits on the basement floor....
Go for it - pics are good! :)

I'll yank the stock piping off later today, and have a measure. I have all the materials available to get it done tonight, which I just might do.
spkrmanThread starter2 · Nov 28, 2006#27
the intake let me get from 169 km/h to 185 km/h... that sounds so much more impressive lol...

Now I know why everywhere else goes by KM/H :)

125mph or 200km/h, which would you have?
eTiMaGoBangkok, Thailand · Nov 28, 2006#28
I like it... ghetto, but effective 😁
hasher22Australia Sydney · Nov 28, 2006#29
Me like, looks ooooooooooooo

i cant wait until i save enough money for a AEM Intake :)
spkrmanThread starter2 · Nov 29, 2006#30
Originally Posted by eTiMaGo
I like it... ghetto, but effective 😁
that it is :)
spkrmanThread starter2 · Nov 29, 2006#31
Originally Posted by hasher22
Me like, looks ooooooooooooo

i cant wait until i save enough money for a AEM Intake :)
i considered buying an AEM intake, or something along those lines.. but wow $200+ for something I spent $30 on to replicate. I'll put in some time/fun and get the same/better results :)

The AEM is pretty sweet though.
hasher22Australia Sydney · Nov 29, 2006#32
Originally Posted by spkrman
i considered buying an AEM intake, or something along those lines.. but wow $200+ for something I spent $30 on to replicate. I'll put in some time/fun and get the same/better results :)

The AEM is pretty sweet though.
I heard good things abour AEM, though if a similar item does the same job and its cheaper, why not get that one.

Though im just buying the brand name 🙂
spkrmanThread starter2 · Nov 29, 2006#33
Originally Posted by hasher22
I heard good things abour AEM, though if a similar item does the same job and its cheaper, why not get that one.

Though im just buying the brand name 🙂
yea, the AEM filter looks real nice, its readily available here for $50. The piping, which isnt even complex, is what costs so much.
vodkalushRochester, NY · Nov 29, 2006#34
hey sprman how about a DIY guide :-), if not then how about a parts list and tube size+length

great job 👍
spkrmanThread starter2 · Nov 29, 2006#35
Originally Posted by vodkalush
hey sprman how about a DIY guide :-), if not then how about a parts list and tube size+length

great job 👍
I don't feel the current design is worthy of a DIY guide - it will be once I build the whole thing up :)

Cost outside of the filter should still be around 10 bux :)
vodkalushRochester, NY · Nov 29, 2006#36
sweetness, as for the MAF i was thinking something like plastic weld and a "nicely" made bracket, just a thought.
vodkalushRochester, NY · Nov 29, 2006#37
oh yeah, waht length and diam is the PVC you used?
spkrmanThread starter2 · Nov 29, 2006#38
Originally Posted by vodkalush
oh yeah, waht length and diam is the PVC you used?
the PVC is 3 ID, and approx 4" long.
ProMotionTuningFredericksburg, VA · Nov 29, 2006#39
spkrman:
Just some advice for you. I have spent many hours on a dyno doing R&D on intake systems. First of all.... Do not use 3" piping on the car... Very bad idea and you COULD throw a CEL or even worse damage the MAF itself. Weapon R and AEM wont use pipes bigger then 2.5" on these motors cause of that. Make sure that MAF is sealed 100% or you will have air leaks which will result in unmetered air and your car could run lean at High RPMs. As far as using 93 octane, definitely no need and you shouldnt be seeing any improvement at all. In fact the damage it is doing to the internals of your car could be worse then the HP you think you have gained.... Your spark plugs from the factory are not rated for the 93 octane and without boost, I am sure you are just helping clog your cats before their time :) Not knocking you just offering advice before your final design!
vodkalushRochester, NY · Nov 29, 2006#40
haha, i'm an a$$. you have the tube size listed like 4x's in the orig post. my bad.
Notthy[Yaris/S]07Puerto Rico · Nov 29, 2006#41
Originally Posted by YarisPR
me avisas cuando lo hagas pq toy loko por uno👍
asi sera tan pronto lo valla a hacer lo pongo con fotos por procedimiento
mikeukrainetzCanada · Nov 29, 2006#42
Originally Posted by ProMotionTuning
spkrman:
Just some advice for you. I have spent many hours on a dyno doing R&D on intake systems. First of all.... Do not use 3" piping on the car... Very bad idea and you COULD throw a CEL or even worse damage the MAF itself. Weapon R and AEM wont use pipes bigger then 2.5" on these motors cause of that.

I havent had a whole lot of experience building intakes but hope maybe you could clarify that and answer a couple of questions.

Is 3" considered a faux-pas because the throttle body bore dia. or actual flow characteristics? Doesnt the 3" just imply the flow could be increased dramatically over stock?

If 3" is bad what about guys who just bolt a cone filter straight to the throttle body?

Obviously if everything has been made in 2.5" dia thats whats been dyno'd but has anyone even tried to dyno a 3"?

The whole intake setup actually seems really similar to the old TPI setup on the old LS1. (Long runner intake ater throttle body, little to none before).
spkrmanThread starter2 · Nov 30, 2006#43
Originally Posted by ProMotionTuning
spkrman:
Just some advice for you. I have spent many hours on a dyno doing R&D on intake systems. First of all.... Do not use 3" piping on the car... Very bad idea and you COULD throw a CEL or even worse damage the MAF itself. Weapon R and AEM wont use pipes bigger then 2.5" on these motors cause of that. Make sure that MAF is sealed 100% or you will have air leaks which will result in unmetered air and your car could run lean at High RPMs. As far as using 93 octane, definitely no need and you shouldnt be seeing any improvement at all. In fact the damage it is doing to the internals of your car could be worse then the HP you think you have gained.... Your spark plugs from the factory are not rated for the 93 octane and without boost, I am sure you are just helping clog your cats before their time :) Not knocking you just offering advice before your final design!
The gas definitely made a difference, im not sure if it was bad gas before, or what... but it definitely made a difference :). If not these plugs, what plugs would I use for 93? Would there possibly be an increase in mileage?

The MAF is sealed as far as I can tell, and yea, it has/is throwing a CEL :)

What other options do I have here? I dont know where to get 2.5" PVC, I see 2.5" metal piping, but I have no way of working with it.

It looks like this kit may fit: http://cgi.ebay.com/ebaymotors/TOYOT...mZ220054255738

Its not loading for me now, but from the smaller pic it looks like it would bolt right in?
spkrmanThread starter2 · Dec 3, 2006#44
you guys think that might fit? Looks like the filter comes back up when it should stay straight, other than that I think it would work great.

Could also just wait on ebay for the piping, shouldnt be TOO long until its out? :)
Chris07LBNew Jersey · Dec 3, 2006#45
Be carefull with any intake with the hose before the MAF sensor... read up/search over on the Scion boards as to why exactly.. but it was talked about at length. 👍

Otherwise, looks like a better fit then most xa/xb short rams would...
spkrmanThread starter2 · Dec 3, 2006#46
the hose is after the MAF there, correct?
Chris07LBNew Jersey · Dec 3, 2006#47
Originally Posted by spkrman ↑
the hose is after the MAF there, correct?
No, its not.

Stock throttle body > EGR Hose > MAF sensor > Filter.... is how the eBay intake is..
vodkalushRochester, NY · Dec 3, 2006#48
deal with my n00bness in that matter; but what is an EGR hose?
spkrmanThread starter2 · Dec 3, 2006#50
Originally Posted by Chris07LB ↑
No, its not.

Stock throttle body > EGR Hose > MAF sensor > Filter.... is how the eBay intake is..
well, teh flow of air is the other way....😎

But either way, the EGR hoseshould be on the OTHER side of the MAF, NOT like the ebay intake, correct?

Is stock not the same exact setup?