TamagoOriginal postOff Grid · May 22, 2009#1www.penguingarage.com DIY instructions for Penguin Garage rear Hub Spacers:
tools required:
~ your wheel removal tools
~ jack and jackstand
~ Hammer
~ small Flat headed screwdriver (ABS-Equipped only)
~ 14MM socket and extension
~ 10MM Allen key (socket preferred for torque wrench)
~ Torque wrench (not required, but recommended)
Step 1: support car with jacking device of your choice. Remove wheel
Step 2: remove rear drum. remember to NOT set your emergency brake! :) tapping with a hammer helps with the drum removal process
Step 3: locate the hub bolts. use a 14mm socket to remove these 4 bolts
Step 4: remove the rear hub/brake assembly. if you are ABS equipped, you'll need a small flat-head screw driver to release the wheel sensor plug before removal of the hub
Picture lost · i29.tinypic.com
use the supplied grease (clear baggie with red grease inside) to lightly coat the mounting surfaces of each spacer. doesn't have to be THICK, just enough to discourage corrosion.
Step 5: insert one supplied bolt thru the hub assembly and slip the spacer over the bolt. this will make re-aligning the hub easier when bolting the hub back to the axle. tighten the hub bolts in a diagonal pattern, torque the new bolts to 80 lb/ft (for those of you who are not torque wrench-equipped, TIGHT). reinstall brake drum, wheel, and set the car down. you're now Penguin Equipped!

Replies 101
supmetSouthern California · May 23, 2009#2wow, even easier than I thought - I was expecting to have to disconnect the brake line and bleed the brakes after.
TamagoThread starterOff Grid · May 23, 2009#3 Originally Posted by
supmet ↑ wow, even easier than I thought - I was expecting to have to disconnect the brake line and bleed the brakes after.
no sir :) on the scion xD it may be recommended to loosen the e-brake cable bracket, but today i found that you don't need to with the yaris. just a little bit of elbow strength and you're back where you started, only wider.
fyi this was a 13mm spacer install :)
TheRealEnthMiami, FL · May 23, 2009#4Dam thats a sick car!!!
TamagoThread starterOff Grid · May 23, 2009#5 Originally Posted by
TheRealEnth ↑ Dam thats a sick car!!!
hah! yes it is! by the way i have the muffler delete pix on my memory card. pending a few quotes, i'm confident we can provide a product to penguin garage that they can sell
tk-421Dagobah · May 23, 2009#6Thanks for the writeup/pics! Can't wait to do this mod. 👍
marcustoronto, canada · May 23, 2009#7any before and after shots.. good job by the way...im definetely getting this but awaitng for new rims..
Penguin GarageFL · May 24, 2009#8Thanks for the great writeup Tamago.
Here is the "after" of the 13mm's installed on a sweet Blue Yaris! 🙂
Picture lost · penguingarage.com
I'll see if I can grab some before photos.
schleppyBoston, MA · May 25, 2009#9Badass. I look forward to your long term review!
TamagoThread starterOff Grid · May 25, 2009#10i've had hub spacers on my scion for 5 years. my review is that they're a necessary mod with no downsides whatsoever :)
marcustoronto, canada · May 25, 2009#11so if i do 13mm.. can i still fit +40 with 195/50/16 on the back without rubbing even if its loaded..when loaded or just 2 people on back the tires gets tucked in the fenders.
Russelt3hPirateEpcot · May 25, 2009#12 Originally Posted by
Tamago ↑ i've had hub spacers on my scion for 5 years. my review is that they're a necessary mod with no downsides whatsoever :)
I have a set as well I'm really glad we got them, i'm actually thinking of upgrading to the new 13mm's instead of my current 10mm's
😁
Russelt3hPirateEpcot · May 25, 2009#13 Originally Posted by
marcus ↑ so if i do 13mm.. can i still fit +40 with 195/50/16 on the back without rubbing even if its loaded..when loaded or just 2 people on back the tires gets tucked in the fenders.
I'd wait till Tamago comes back to confirm but according to my calcs, you'd be fine at 13mm. Although a 10mm would give you a little extra comfort room and still look great.
whooppee777Maryland · May 25, 2009#14nicely done
marcustoronto, canada · May 25, 2009#15 Originally Posted by
Russelt3hPirate ↑ I'd wait till Tamago comes back to confirm but according to my calcs, you'd be fine at 13mm. Although a 10mm would give you a little extra comfort room and still look great.
ok thanks..but would 3 mm make a big difference..seems so small of a difference though..
Russelt3hPirateEpcot · May 25, 2009#16 Originally Posted by
marcus ↑ ok thanks..but would 3 mm make a big difference..seems so small of a difference though..
it wouldn't make a big difference, 3mm is a lot for looks though.
if you're worried about rubbing I'd do the 10mm, if you want the most aggressive look go with the 13mm.
are your wheels 7" wide?
TamagoThread starterOff Grid · May 26, 2009#17added a blurb about grease. first sets of spacers DID NOT ship with grease as my supplier was on the lam. any water-repelling lubricant should work fine
GideonSunnyvale, CA · May 26, 2009#18Did my install today in about an hour.
Driver's side was easy, but passenger side was a little more of a pain. Drum did NOT want to come off. 😠
Also, Tamago did you notice the tightness in the lower brake line when you didn the install on Enth's? My driver side was tight, but passenger side was damn near impossible to get the holes to line up because of how tight the brake line was, it had no more slack, lol.
Also, the ABS sensors wires were a pain in the ass.
TamagoThread starterOff Grid · May 26, 2009#19 Originally Posted by
Gideon ↑ Did my install today in about an hour.
Driver's side was easy, but passenger side was a little more of a pain. Drum did NOT want to come off. 😠
Also, Tamago did you notice the tightness in the lower brake line when you didn the install on Enth's? My driver side was tight, but passenger side was damn near impossible to get the holes to line up because of how tight the brake line was, it had no more slack, lol.
Also, the ABS sensors wires were a pain in the ass.
i really didn't notice a difference.. but yeah, you can loosen up the e-brake line to assist with flexibility. slip a small screwdriver into the plug to release it
DerFlosserUSA · May 27, 2009#20Very cool. I think that these are now on my list of things to do! Thanks for sharing...🍻
YarisSedanCalifornia - Bay Area · May 27, 2009#21Did you notice any difference in handling or how the car drives. It is really annoying how the rear tires do not sit flush with the body like the front do. I cant wait to get mine.
GideonSunnyvale, CA · May 29, 2009#22Not really no. Can't say that I have. Although it's only been a couple of days and I have yet to take it up to the twisties to have some fun. 🤷
Worth it to not have the sunken-in look IMO.
tk-421Dagobah · May 29, 2009#23I just installed my set, but the passenger side is rubbing (I guess I should've made sure I got 2 10mm sets before installation). Also, one of the screws on the driver side (lower-right) did not go through the hole, so I ended up using a shorter one instead. Is that OK?
DerFlosserUSA · May 29, 2009#24 Originally Posted by
tk-421 ↑ ...Also, one of the screws on the driver side (lower-right) did not go through the hole, so I ended up using a shorter one instead. Is that OK?
screw? Do you mean bolt...and are talking about the hub mounting bolt?
TamagoThread starterOff Grid · May 29, 2009#25 Originally Posted by
tk-421 ↑ I just installed my set, but the passenger side is rubbing (I guess I should've made sure I got 2 10mm sets before installation). Also, one of the screws on the driver side (lower-right) did not go through the hole, so I ended up using a shorter one instead. Is that OK?
it didn't go through? meaning it was too long?
i'm trying to recall if i sent lock washers with your set or not. a lock washer should space the bolt out so it doesn't touch the axle.
are you saying i sent you a 10 and a 13? please double check this, as my counts are still even in my inventory
YarisSedanCalifornia - Bay Area · May 29, 2009#26Hmmm mine didnt come with any washers. Should i be worried?
Also no penguin sticker too =(
TamagoThread starterOff Grid · May 29, 2009#27no need to worry, washers are not required on 13mm sets, and are only sometimes needed on 10mm sets. and the penguin stickers JUST arrived today, didn't want to hold up spacer shipments for mere stickers
tk-421Dagobah · May 30, 2009#28 Originally Posted by
DerFlosser ↑ screw? Do you mean bolt...and are talking about the hub mounting bolt?
Yes
Originally Posted by
Tamago ↑ it didn't go through? meaning it was too long?
The lower-right bolt on my passenger-side rear wheel went in fine, but it didn't go out, meaning that the hole at the other end wasn't large enough to fit the bolt. I ended up using an OEM bolt instead, which didn't go through by 3-4 threads, so I'm a bit worried it may snap.
i'm trying to recall if i sent lock washers with your set or not. a lock washer should space the bolt out so it doesn't touch the axle.
Could I get a picture of those washers you mentioned?
are you saying i sent you a 10 and a 13? please double check this, as my counts are still even in my inventory
I am pretty sure I got it figured out now. I had a scrape removed from the passenger side fender a few days ago. Looks like the "ding doctor" ended up flattening the fender area a bit too much, making the tire rub with the fender. I may have to roll it back out a bit to fix that. So I'm 99.99% sure I did get 2 10mm spacers after all.
TamagoThread starterOff Grid · May 30, 2009#29 Originally Posted by PK198105 ↑
you know what Tamago im getting these for sure next week! although im scared shitless of installing them myself. also wont different metals fuse together? (🤷 i heard somewhere you cant mix metals)
i'm including grease with all the shipments now to coat the spacers before assembly. that will slow down the corrosion process.
TK, perhaps take the bolt i sent and have it cut off a little? i haven't run into this issue with any of the 4 cars i've done so far.
and the washer is simply a 1/2" split lock washer, nothing fancy
DerFlosserUSA · May 30, 2009#30These bolts should basically be OEM length plus whatever spacer size you get (adding the additional stack height). I plan to be able to install these without issue when I get them....maybe penguin garage could come on here and talk about how they package their kits?
Penguin GarageFL · May 30, 2009#31Each kit comes with:
2 spacers
8 bolts
1 packet of grease
8 lockwashers (10mm spacers)
the bolts are of sufficient length to stack up to 26mm in width.
YarisSedanCalifornia - Bay Area · May 30, 2009#32Hmmm my 10mm kit came with no lockwashers. Maybe i got sent the wrong kit and got a 13mm one instead?? I need to grab a tapemsure now
DerFlosserUSA · May 31, 2009#33note: Installed these this a.m. and everything was easy aside from getting the drum off. I don't know why I didn't try earlier but my steering wheel puller was the CORRECT and EASY way to remove the drum. Took 2 seconds and no hammer.
Penguin GarageFL · May 31, 2009#34 Originally Posted by
YarisSedan ↑ Hmmm my 10mm kit came with no lockwashers. Maybe i got sent the wrong kit and got a 13mm one instead?? I need to grab a tapemsure now
we can send you some lock washers on Monday.
Sorry about that.
EDIT: also sending out Penguin Stickers to all those who didn't get them yet. :)
DerFlosserUSA · May 31, 2009#35I painted the hub spacers exposed portion with eastwood chassis black. I bet a Toyota tech wouldn't even recognize them. 😉
These make a nice subtle difference for sure....the car is one step closer to looking the way the it should have come from the factory.👍 Thanks Penguin Garage.😎
TheRealEnthMiami, FL · May 31, 2009#36GIMMIE MY STICKERZ!!1111
Penguin GarageFL · May 31, 2009#37 Originally Posted by
TheRealEnth ↑ GIMMIE MY STICKERZ!!1111
whoa, yelling isn't going to make USPS go faster. haha.
although Tamago has a stack of White Ones for the South Florida Yaris Peoples. :)
PHXDEMONPhoenix, AZ · May 31, 2009#38Nice diy 👍 I'll have to pick a pair of these up when i get paid.
Bob Dogthe Boondocks, NC · Jun 2, 2009#39Special Torque setting? As in do I need a torque wrench to do this simple procedure correctly?
TamagoThread starterOff Grid · Jun 2, 2009#40if you want to torque the bolts, you'll need a torque wrench. however, "tight" isn't very hard to achieve :)
AltitudeColorado · Jun 5, 2009#41Got mine a week ago. Put them on today and I'm digging the new look 👍 😁 Sorry for not taking before and after shots, but that's just how I roll. Hardcore, no pics.
Anyhow, the install was a breeze though I suggest when pulling the drum that you use those two screw holes provided. I tried prying it off a couple of different ways but didn't want to damage the back plate or anything else for that matter so the bolt in the hole did the trick. I just happened to have a small bolt that was perfect for it though I don't know the thread size. Just torqued on one hole til it started to pop off then did the opposite side. Piece of cake.
Easy mod for a beefier looking back end. Haven't taken it through any turns to see if it makes a huge difference in handling, but given that the change is very noticable to the eye I would expect some extra stability out of it.
I highly recommend this mod. Thanks Penguin Garage and Tamago!
marcustoronto, canada · Jun 5, 2009#42size of that bolt would definetely come in handy...i do use bolt to pry out the rotor as well if its stuck on the hub. makes is alot easier..and thats what those 2 or 3 small holes are for.
Originally Posted by
Altitude ↑ Got mine a week ago. Put them on today and I'm digging the new look 👍 😁 Sorry for not taking before and after shots, but that's just how I roll. Hardcore, no pics.
Anyhow, the install was a breeze though I suggest when pulling the drum that you use those two screw holes provided. I tried prying it off a couple of different ways but didn't want to damage the back plate or anything else for that matter so the bolt in the hole did the trick. I just happened to have a small bolt that was perfect for it though I don't know the thread size. Just torqued on one hole til it started to pop off then did the opposite side. Piece of cake.
Easy mod for a beefier looking back end. Haven't taken it through any turns to see if it makes a huge difference in handling, but given that the change is very noticable to the eye I would expect some extra stability out of it.
I highly recommend this mod. Thanks Penguin Garage and Tamago!
marlondogLost Angeles · Jun 13, 2009#43Where on the drum are you tapping with the hammer? Are you using a screwdriver as well to help pry it off?
TamagoThread starterOff Grid · Jun 13, 2009#44 Originally Posted by
marlondog ↑ Where on the drum are you tapping with the hammer? Are you using a screwdriver as well to help pry it off?
i've never had this issue, as i remove my drums every time i remove my rear wheels (simply to keep the corrosion factor to a minimum) however there is a small slot between the drum and the backing plate. you should be able to stick the corner of a block of wood (or a brass/copper punch) in this groove and go to town.
I apologize that i have not yet posted the bolt spec for pushing the drum off of the hub. my guess is that it's a standard metric bolt (coarse thread) that has a 10mm thread. 8MM possibly? i'll definitely let you guys know my findings, i'll be doing new rear brake shoes soon.
marlondogLost Angeles · Jun 14, 2009#45Finally figured it out. It looks dope!
Originally Posted by
Tamago ↑ i've never had this issue, as i remove my drums every time i remove my rear wheels (simply to keep the corrosion factor to a minimum) however there is a small slot between the drum and the backing plate. you should be able to stick the corner of a block of wood (or a brass/copper punch) in this groove and go to town.
I apologize that i have not yet posted the bolt spec for pushing the drum off of the hub. my guess is that it's a standard metric bolt (coarse thread) that has a 10mm thread. 8MM possibly? i'll definitely let you guys know my findings, i'll be doing new rear brake shoes soon.
TamagoThread starterOff Grid · Aug 4, 2009#46edited. i added the ABS plug removal bit, stolen from the factory svc manual.
advocatelocation · Dec 25, 2009#47Alright just got the spacers in. My kit didn't come with a penguin either but I did have camber shims and lube.
I'm worried about my brakes though because they're not as responsive as before. I noticed a big difference after putting in the spacers and braking. It's somehow related to the brake lines because they had to be stretched a little bit to reach the hub after it was spaced further from the car.
YarisSedanCalifornia - Bay Area · Dec 25, 2009#48 Originally Posted by
advocate ↑ Alright just got the spacers in. My kit didn't come with a penguin either but I did have camber shims and lube.
I'm worried about my brakes though because they're not as responsive as before. I noticed a big difference after putting in the spacers and braking. It's somehow related to the brake lines because they had to be stretched a little bit to reach the hub after it was spaced further from the car.
You should have any issues. Its possible you may have slightly kinked a brake line. You could try adjusting your rear brake shoes to see if helps.
YAR1SRaleigh, NC · Dec 25, 2009#49I hate to say this but maybe a re-think on the sticker design is in order.... my penguin's beak got ripped off today after carefully sticking and re-sticking everytime I wash my car...... poor thing is this blobb animal now.... :(
YAR1SRaleigh, NC · Dec 25, 2009#50 Originally Posted by
Tamago ↑ i've never had this issue, as i remove my drums every time i remove my rear wheels (simply to keep the corrosion factor to a minimum) however there is a small slot between the drum and the backing plate. you should be able to stick the corner of a block of wood (or a brass/copper punch) in this groove and go to town.
I apologize that i have not yet posted the bolt spec for pushing the drum off of the hub. my guess is that it's a standard metric bolt (coarse thread) that has a 10mm thread. 8MM possibly? i'll definitely let you guys know my findings, i'll be doing new rear brake shoes soon.
Tapping of the drum isnt really nessacary.... luckily the drum has two screw holes that take care of popping off the drum.... I thought I posted this already?🤷