Replies continued
Penguin GarageFL · Dec 27, 2009#51 Originally Posted by
YAR1S ↑ I hate to say this but maybe a re-think on the sticker design is in order.... my penguin's beak got ripped off today after carefully sticking and re-sticking everytime I wash my car...... poor thing is this blobb animal now.... :(
until we do a re-design I can send you a fresh one. :)
what color do you want?
Penguin GarageFL · Dec 27, 2009#52 Originally Posted by
advocate ↑ Alright just got the spacers in. My kit didn't come with a penguin either but I did have camber shims and lube.
I'm worried about my brakes though because they're not as responsive as before. I noticed a big difference after putting in the spacers and braking. It's somehow related to the brake lines because they had to be stretched a little bit to reach the hub after it was spaced further from the car.
Who did you get them thru?
Shoot me a PM I'll get one sent out to you.
Dj_SloKidFlorida · Feb 24, 2010#53what is the hub spacer for anyways? ikno ima noob
TamagoThread starterOff Grid · Feb 24, 2010#54 Originally Posted by
Dj_SloKid ↑ what is the hub spacer for anyways? ikno ima noob
www.penguingarage.com hub spacers effectively lower your rear offset, making the rear track wider.
33OHDover, Ohio · Mar 16, 2010#55Hub spacer install - 1
Me - 0
Spent around 3 hours trying to get the hub assembly "un-stuck." Ended up calling it a night and putting it all back together.
Will have to pick up my air chisel I lent out and try again.. 😠
33OHDover, Ohio · Mar 16, 2010#56Oh and FYI - the bolt size is a 12mm to get the drum off, you can use two that hold your hood on. (Use one from each side, obviously, so your hood can still stay on the car.)
YAR1SRaleigh, NC · Mar 16, 2010#57 Originally Posted by
ryank ↑ Oh and FYI - the bolt size is a 12mm to get the drum off, you can use two that hold your hood on. (Use one from each side, obviously, so your hood can still stay on the car.)
how could you not get the hubs unstuck with the bolts? Im confused.... this did it for me.... 🤷
33OHDover, Ohio · Mar 17, 2010#58It is seized onto the assembly. I'll have to grab an air chisel and see if the vibrations will knock it off.
TamagoThread starterOff Grid · Mar 17, 2010#59don't use an air chisel.
rent a slide hammer kit
Picture lost · bertram-hill.co.uk
33OHDover, Ohio · Mar 17, 2010#60Ah alright. Auto parts store I'm assuming will have one?
TamagoThread starterOff Grid · Mar 17, 2010#61 Originally Posted by
ryank ↑ Ah alright. Auto parts store I'm assuming will have one?
yeah, autozone for sure.
you could also re-install the wheel and kick against it from under the car, using it as leverage. i had a hell of a time getting the hubs off my MR2 to install my spacers too.
33OHDover, Ohio · Mar 17, 2010#62Ah that's a good idea too with the wheel. I'll stop by autozone on my way home today. Thanks Joel. 😎
WeeYariGeorgetown, Ontario, Canada · Mar 17, 2010#63Is the e-brake released? Just checking ;)
33OHDover, Ohio · Mar 17, 2010#64Yeah the e-brake was released. =)
33OHDover, Ohio · Mar 19, 2010#65Btw - I got it. They look great!
Mounting the wheel onto the hub assembly was what did it for me. Had trouble getting the wheel OFF the assembly though, but a "chisel" and a sledge hammer did the job.
derickveliz2Central, MA · Apr 29, 2010#66... Shame on me, I just couldn't get the drum out )o: I'll try with the bolts that hold the hood.
D.
.
derickveliz2Central, MA · May 1, 2010#67 Originally Posted by
derickveliz2 ↑ ... Shame on me, I just couldn't get the drum out )o: I'll try with the bolts that hold the hood.
Piece of Cake!
Now the 14 mm are giving me a hard time, I guess I need beefier tools... Or work out harder at the Gym! 😆
D.
cali yarisCanoga Park, CA · May 1, 2010#68 FYI - the bolt size is a 12mm to get the drum off, you can use two that hold your hood on.
SUPER CLEVER 🙇
derickveliz2Central, MA · May 3, 2010#69I did it! I did it! But only one side! The good thing is I'm going to be able to take photos of each side and compare! In real life It looks so GOOD! and this is only 10mm but makes such a big difference.
The right tools made a big difference, day and night, I'm a novice with real tools and mechanics, for me a guy who spends 60 or more hours per week in front of a computer, this is a big achievement!
I had trouble getting the spacer to fit, there was some "RUST" that made the inner circle impossible to fit with my hands, and the break like was so tight that I had to unscrew some points down the line to give me a little play and get everything back in place with the spacer in the middle. Used a lot of WD-40 and used the power of the tools to force/make the spacer fit.
We'll see how the other side goes tonight!
Thanks.
D.
derickveliz2Central, MA · May 3, 2010#70Here are the pictures...
From the Back:
From the Front:

cali yarisCanoga Park, CA · May 3, 2010#71awesome!!
derickveliz2Central, MA · May 5, 2010#72Did the other side, it was much faster but at the end the RUST made everything a little challenging! but now every thing is OK.
Thanks "Pinguino" Spanish version!
D.
spookzSydney, Australia · May 5, 2010#73Looking good! It looks like your passenger side is tucked in a few mm more than the driver side though.. my Yaris is the same..
RacerFreakXXXSomers NY · May 5, 2010#74I just installed these on my car and they look amazing! I'll take pics when the car is back on the lift. Just remember to be careful while doint the install, you don't want to screw the threads up like me 👍 It's also best to have someone else there to help you out too.
derickveliz2Central, MA · May 5, 2010#75 Originally Posted by
spookz ↑ Looking good! It looks like your passenger side is tucked in a few mm more than the driver side though.. my Yaris is the same..
Thanks
What do you mean? where did you see that?
D.
.
derickveliz2Central, MA · May 6, 2010#76I just put my new wheels and I have rubbing issues in the back, I tried to uninstall the spacer but it was impossible. )o: any tips would be appreciated.
Thanks.

HerbicidalRoseville, CA - USA. · May 11, 2010#77 Originally Posted by
derickveliz2 ↑ I just put my new wheels and I have rubbing issues in the back, I tried to uninstall the spacer but it was impossible. )o: any tips would be appreciated.
Thanks.

Photobucket images are blocked at work, so I can't see the pic. 😠 Anyway, will some kind of "puller" work? (Someone else mentioned a steering wheel puller, but I believe that was used to remove the brake drum.) Along with some heat and PB Blaster? I'm sure that bit of rust is holding it on... Even if you can't work on it today, getting some PB Blaster sprayed in there now would give it a couple of days or more to work it's magic. Then you can try again on the weekend.
fnkngrvIn The Hotbox · May 11, 2010#78Might be a stupid question, but if someone installs the Rear Disc Brake Conversion Kit the spacers would be a moot point correct?
marcustoronto, canada · May 17, 2010#79im curious if someone tried adding washer on the bottom..to make the tire tilt by a little angle..
Russelt3hPirateEpcot · May 17, 2010#80 Originally Posted by
marcus ↑ im curious if someone tried adding washer on the bottom..to make the tire tilt by a little angle..
The Penguin Garage Camber Shims did exactly that. :)
Russelt3hPirateEpcot · May 17, 2010#81 Originally Posted by
fnkngrv ↑ Might be a stupid question, but if someone installs the Rear Disc Brake Conversion Kit the spacers would be a moot point correct?
they wouldn't be moot but you would need another spacer for the caliper.
I know a guy out in Europe installed a set of the PG spacers on his Vitz RS which had rear disc brakes. :)
marcustoronto, canada · May 17, 2010#82 Originally Posted by
Russelt3hPirate ↑ The Penguin Garage Camber Shims did exactly that. :)
kewl..im assuming it comes with it.... is the stickers still free by the way..anyone..thanks..
TamagoThread starterOff Grid · May 19, 2010#83 Originally Posted by
marcus ↑ kewl..im assuming it comes with it.... is the stickers still free by the way..anyone..thanks..
i have spacers that i've manufactured for another car. for disc brakes. i won't provide bolts though.
marcustoronto, canada · Jun 5, 2010#84I'm curious what the 10mm Allen key is used for?
marcustoronto, canada · Jun 5, 2010#85Forget it I found it
marcustoronto, canada · Jun 13, 2010#86just to add on to this..for hatchback left rear is about 4mm pushed in vs the right.. i did an install on pg spacer left rear 13mm and right is 10mm and i got it pretty close to match..yaris frame is crooked by about 4mm rear left.
marcustoronto, canada · Jun 21, 2010#87this thing wont work for 205/50/16 +40 offset. i did 13mm on left and 10mm on the right (due to left goes in more than the right..)got it flush on both side but still rubbing on the right shaved the fender worked well but with soneone on the back still getting rubadubdub on dips..i should have placed the shim .damn it! but now i dont want to do it if its not gonna fix the issue..1degree ?? would that move the upper tires in by what 2mm or less..
update... left rear for hatch is 5mm off vs right rear.. get 13mm n 8mm or 15mm n 10mm
derickveliz2Central, MA · Aug 2, 2010#88.
I installed a camber kit, thanks to Garm and other yariswold members for your suggestions trying to avoid rubbing.
The installation is very easy if you have done the spacers, I added -1.5 degrees and Looks and Feels AWESOME!!! it does help with the rubbing issue but I still need to drive with more weight and find out.
D.
33OHDover, Ohio · Aug 3, 2010#89My right side is out further than the left, actually. 🤷😳
derickveliz2Central, MA · Aug 3, 2010#90 Originally Posted by
33OH ↑ My right side is out further than the left, actually. 🤷😳
I know what you feel, you are not alone... It bothers me a little bit, but If I don't tell.. nobody notice the discrepancy.🙂
D.
🎉
marcustoronto, canada · Aug 3, 2010#91im running 16x7 +40 offset and just added 5mm spacer on the left rear.. looks alot more even compare to stock crooked frame..
derickveliz2Central, MA · Aug 3, 2010#92 Originally Posted by
marcus ↑ im running 16x7 +40 offset and just added 5mm spacer on the left rear.. looks alot more even compare to stock crooked frame..
Where did you get the 5mm spacer?
D.
DeathBeardLos Angeles, CA · Aug 3, 2010#93any local tire shop should carry a 5mm spacer
marcustoronto, canada · Aug 3, 2010#94or any tire and rim place..cost me $10 bucks..i actually had 13mm for left and 10 mm for right spacer fr penguin but rubbing on me due to my offset..but itll work perfect for 45mm offset..
derickveliz2Central, MA · Sep 8, 2010#95Finally I was able to
pull out the spacers, when I was going to put back the camber kit I noticed that didn't fit and I had to trim the inner circle of the camber kit to make it fit, I wonder if this discrepancy had to do with the fact that the
spacers where stuck! Thoughts?

TamagoThread starterOff Grid · Sep 11, 2010#96did you grease them before install?
derickveliz2Central, MA · Sep 11, 2010#97 Originally Posted by
Tamago ↑ did you grease them before install?
Yes I did, and I noticed that they didn't fit loose but very tight and put extra grease, the lugs slowly set the spacers in place by pressure putting everything back together.
D.
TamagoThread starterOff Grid · Sep 12, 2010#98 Originally Posted by
derickveliz2 ↑ Yes I did, and I noticed that they didn't fit loose but very tight and put extra grease, the lugs slowly set the spacers in place by pressure putting everything back together.
D.
the lug nuts pulled the spacers on tight?
did you remove any of the rust buildup on the hub itself before installing the spacer?
derickveliz2Central, MA · Sep 14, 2010#99 Originally Posted by
Tamago ↑ the lug nuts pulled the spacers on tight?
did you remove any of the rust buildup on the hub itself before installing the spacer?
Yes I did!
I was surprised that even the camber kit didn't fit and I had to trim it.
D.
SKurjGTA · May 21, 2011#100 Originally Posted by
marcus ↑ or any tire and rim place..cost me $10 bucks..i actually had 13mm for left and 10 mm for right spacer fr penguin but rubbing on me due to my offset..but itll work perfect for 45mm offset..
This is perhaps the kit penguin should sell. Just fitted the 10mm on mine and was surprised how obvious the difference between the left and the right is. Well at least to me. 13-15mm for left, 10mm for right.