gwasabiOriginal postHonolulu, Hawaii · Apr 3, 2009#1I've been reading a bunch of people who installed the throttle body and are having CEL coming on. I used to drive a G35 and a Celica and having done intake mods to it and having CEL come on, I asked one of my modder friends to help me get rid of this. This trick worked on both my celica and G35. This should get rid of the Oscillation and CEL light after installing the 1zz TB.
NOTE: THIS ONLY WORKS FOR MANUAL TRANS! AUTO TRANS HAS A SET TB OPENING POINT SO THIS METHOD WON'T WORK!
Step 1: Install TB....I don't have a DIY for this, just find someone else's and do so.
Step 2: Get all the air out of the Radiator hose. This is done by popping off the radiator cover and running the engine until the radiator doesn't bubble anymore. It should overflow a bit. Just cap it once it does.
NOTE: STEP 2 IS VERY VERY VERY IMPORTANT!!!! THIS IS THE REASON WHY WOU WILL GET RANDOM OSCILLATION AND CEL DURING DRIVING!!!!
Step 3: Disconnect battery over night (I disconnected for about 2 hours). This is to make sure the ECU resets itself. Then reconnect the battery.
Step 4: Turn car on and you will notice it oscillate for a while. Usually for about 2 min or so. let it settle.
Step 5: IN NEUTRAL, Rev the car up to about 4-5k RPM for about 5 min. Then let the car idle for about 2 min. Then Rev the car up to about 4-5k RPM for another 5 min. The ECU learns how you drive and tries to adjust the AF ratio according to your driving performance. Doing this step tricks the ECU into thinking that you are driving "super crazy racer maniac style".....honestly its just saying you drive with a heavy foot so it puts more fuel at a faster rate to compensate for the amount of air coming in.
NOTE: IN STEP 5 I ONLY PUT THAT YOU DO THIS CYCLE TWICE. I ACTUALLY DID IT ABOUT 3 -5 TIMES. THIS IS TO PUT THE ECU INTO THINKING YOU DRIVE HARDER TO COMPENSATE FOR THE EXTRA AIR BEING LET IN. IF YOUR WORRIED ABOUT THE ENGINE THEN USE A CYCLE OF 3-1-3-1-3-1 (ex. 3 min rev at 4k, then 1 min of idle). ALSO NOTE YOU HAVE TO HAVE IT AT 75% OPEN THROTTLE which will bring the car up to about 4-5K in RPM.
Step 6: Turn car off for about 5 min. Start it up. And Test drive. If you still get the CEL an oscillation, park, then do Step 5 again.'
NOTE: TURNING THE CAR OFF HELPS THE ECU TO STORE YOUR DRIVING STYLE AND LET IT SETTLE DOWN. YOU DON'T NORMALLY HAVE TO DO THIS STEP BUT I SUGGEST YOU DO AS A PRECAUTION!
DRIVE IT AROUND FOR A WEEK. During this week you will get some CEL and oscillation but it should go away soon. if it continues after a week try Step 5 again.
I did this trick on my celica, g35, and Yaris and seem to have worked all three times. My yaris is running off the 1zz throttle body without the chip mod and I haven't had oscillation or CEL thrown for over 3 months. when I did this trick, the CEL and oscillation went away immediately.
I'm not garanteeing this as a surefire way to get rid of it but it seems to work on most cars. Try it out if you have the time and let me know!
Hope it works for you guys too!
BTW I drive a 07 Yaris HB MANUAL!
Replies 104
yarstarGeorgia · Apr 3, 2009#2Thanks for posting this fix.
Does this also fix the high rpm cold idle?
AlexNet0Rockland, ME · Apr 3, 2009#3I do not believe you can fix the high COLD idle, as the butterfly valve opening is around 30% larger, therefore it opens the throttle 30% more without realizing it.
eTiMaGoBangkok, Thailand · Apr 4, 2009#4Yeah gwasabi's procedure should help, the ECU does have a learning feature for the throttle controller, letting it idle for a while *after* using the engine (driving, or revving in place like this) should kick this in.
BLAZINBLUEVITZNEW YORK · Apr 4, 2009#52 things come to mind. i have no tach so how do i know rpms and isn't 5k a bit high to be reving for 5 minutes straight......
CASTREXCosta Rica · Apr 4, 2009#6I wonder if we could trick the ecu into think the Yaris is a F1 car instead of an Econobox....🙄
J/K
You got me lost with something... what does the radiator has tod do with the hole ECU re learning process?
But yeah... the ECU learns the way you drive. I found that a long time ago when I was doing an audio installation to the car and the battery was unpplugged for over 24hrs.
When I drove the car after that it was really slow... laggy response... but after 30 min of suffering my driving style it came back to normal....
I guess it helps to do this during night or with a fresh climate instead of doing it on a hot day.
talnlnkySpokane, Wa · Apr 4, 2009#7 Originally Posted by
CASTREX ↑ I wonder if we could trick the ecu into think the Yaris is a F1 car instead of an Econobox....🙄
J/K
You got me lost with something... what does the radiator has tod do with the hole ECU re learning process?
I'll take a stab and guess that that's solely for cooling purposes. Any air in the radiator will reduce its cooling abilities, since you'll be revving at 5k fro 5 mins at a time, seems as though a little extra cooling might be a good idea.
AlexNet0Rockland, ME · Apr 4, 2009#8did anyone still have oscillation AFTER the 1zz to 1nz chip swap?
gwasabiThread starterHonolulu, Hawaii · Apr 4, 2009#9The radiator part (Part 2) is so after you install the 1zz you get all the air bubbles in the coolant hose out. If you have air in the coolant hose then you will get a CEL at wierd times. You'll be driving about 20 miles without it on then about 2 miles with it on then another 20 miles without it on. When the air goes through the coolant hose and goes through a certain part of the car, it will reduce your car's tourque dramatically. You can actually feel the loss of power. You'll be driving fine for a while then all of a sudden a dip in the powerband then it goes back up gradually. Also, your hose might explode(not really explode but the air causes a gap in the hose bung) and leak coolant all over your engine bay......it happened to me.
You can figure out roughly where your RPM limitor is at by reving as hard as u can and see where your rev bounces then from there make an educated guess :) I just reved mine up about 3/4 way
yarstarGeorgia · Apr 4, 2009#10 Originally Posted by
AlexNet0 ↑ did anyone still have oscillation AFTER the 1zz to 1nz chip swap?
Oscillation gone after chip swap with mine. Only problem is high cold idle. I can live with that for the increase in power this gives.
PHXDEMONPhoenix, AZ · Apr 5, 2009#11just to double check the throttle body off an 03/04 matrix/corolla is the one everyone is doing the swap with correct?
AlexNet0Rockland, ME · Apr 5, 2009#12 Originally Posted by
PHXDEMON ↑ just to double check the throttle body off an 03/04 matrix/corolla is the one everyone is doing the swap with correct?
'05 and up drive by wire Tb's from the matrix/corolla with the 1zz engine
good luck m8 i wait for your results....
so kustom did your car blow up lol or is it ok
thebarberGrand Rapids, MI · Apr 11, 2009#15i did a similar procedure w/ my tb last year and never had problems. you've GOT TO disconnect the battery and when the new tb is installed, let the car idle for 10-15min before a test drive
alexnet0 is right, the high cold idle wont go away due to the 1zz tb being so much larger than th 1nz tb
i still have an extra 1zzfe tb for sale btw
tk-421Dagobah · Apr 11, 2009#16I don't like the cold idle at all. I keep feeling that I may be stressing the internals more than before...
PHXDEMONPhoenix, AZ · Apr 11, 2009#17How high is the cold idle? Like 3k RPM?
i can take that tb off your hands rigth now barber it is the right one for the yaris? fits the 08 SD?
gwasabiThread starterHonolulu, Hawaii · Apr 11, 2009#19my cold idle is 2k
tk-421Dagobah · Apr 11, 2009#20My cold idle is almost exactly @ 2.5K
at3GGVA Beach · Apr 13, 2009#21couple of questions....where did you guys get these tb's? Junkyard ? how much did they cost you? Can you feel a noticeable power increase? Has your MPG suffered? And the last and most n00b question...how many do you need anyway?
gwasabiThread starterHonolulu, Hawaii · Apr 13, 2009#22In hawaii, You can get these at junkyard for Cheeeeeeeeep! 20 bucks for some high scaled junkyard, FREE.99 for some whatever kind junkyard as long as you get big pocket. I bought mine from barber though....you never know what happened to the TB in the junkyard might be all buss up.
BIG NOTICABLE POWER INCREASE! Midrange to Higher RPM. I used to have trouble getting to 60 in stock after TB it goes 90 easy. MPG goes down but not by much. I noticed around 3 or 4 mpg. and you only need one TB
Hit up barber I think he has a extra one
MGarganoNJ · Apr 13, 2009#23Just installed my 1ZZ TB and got a CL instantly on first start-up to clear the bubbles from the radiator hose (Step 2). I have the car sitting now with the battery disconnected... will try steps 4-6 in a few hours. Hopefully this works since I more than a little nervous about trying the chip swap!
at3GGVA Beach · Apr 13, 2009#24how hard is this to swap?? anything required besides the TB itself?
at3GGVA Beach · Apr 13, 2009#25and barber how much for the TB you have?
gwasabiThread starterHonolulu, Hawaii · Apr 13, 2009#26No not hard at all just gasket i guess
at3GGVA Beach · Apr 13, 2009#27gasket? as in modifying the stock one or purchasing/ making a new one? Pretty n00b at this as you can see. Any one interested in doing a DYI lol
gwasabiThread starterHonolulu, Hawaii · Apr 13, 2009#28Gasket maker. That's what most people are using. I didn't use any gasket though.....mine didn't come with one stock so I figure just put em in hahaha
at3GGVA Beach · Apr 13, 2009#29haha nice...anyone got any pics of install or before/after etc?
MGarganoNJ · Apr 13, 2009#30I just went out to perform steps 4-6. The engine oscillated for about two minutes and gave me the high cold idle, but the CL is gone without doing steps 4-6. I'm hoping the oscillation goes away and the CL stays off. I guess time will tell.
gwasabiThread starterHonolulu, Hawaii · Apr 14, 2009#31Oscillation should be gone too try doing the steps one more time usually it should only takes the ECU 15min to learn the drive style but it might be a little dumb so go try it one more time oscillation should go away
MGarganoNJ · Apr 14, 2009#32I actually didn't do the steps since the CEL didn't come back on. I figured the oscillation would just go away on its own after driving the car normally for a while? Or should I do the steps anyway?
gwasabiThread starterHonolulu, Hawaii · Apr 14, 2009#33you should do the step or oscillation will come back until you do it because the ecu gets confused. if you dont do the last steps the oscillation will come back randomly while your driving.
MGarganoNJ · Apr 14, 2009#34 Originally Posted by
gwasabi ↑ you should do the step or oscillation will come back until you do it because the ecu gets confused. if you dont do the last steps the oscillation will come back randomly while your driving.
Ok, will do the last steps today then. Thanks!
so well how does it feel?
at3GGVA Beach · Apr 14, 2009#36im thinking i want this mod lol gotta save up some cash...
MGarganoNJ · Apr 14, 2009#37 Originally Posted by
Yoda ↑ so well how does it feel?
Feels great. Engine feels more 'alive'. Definitely more pep and power. I didn't get the oscillation at cold idle this morning, but it did throw a CEL after driving for a few minutes. Should I disconnect the battery for a while and then do the last few steps?
at3GGVA Beach · Apr 14, 2009#38i think theyre saying to just live with the CEL for maybe a day or two and just let the ECU adapt. I would give that a shot.
MGarganoNJ · Apr 14, 2009#39I have the battery disconnected now... will run through the steps in a few hours...
MGarganoNJ · Apr 14, 2009#40Did step five 2 1/2 times and the oscillation is gone. CEL hasn't come back either. Will check again tomorrow morning when cold starting. Revving up to 4,500 in neutral for 5 minutes was probably the hardest part... poor little car!
at3GGVA Beach · Apr 14, 2009#41heh poor neighbors
MGarganoNJ · Apr 14, 2009#42 Originally Posted by
at3GG ↑ heh poor neighbors
I actually did have someone peek his head out and give me a 'WTF' look
at3GGVA Beach · Apr 14, 2009#43hahaha nice get em a donut in the morning all will be forgiven!
gwasabiThread starterHonolulu, Hawaii · Apr 14, 2009#44lol I was revving mine at red line(6k) for 5 min twice hahahaha
MGarganoNJ · Apr 14, 2009#45lol it'll all be worth it if this keeps the CEL and oscillation away
tk-421Dagobah · Apr 15, 2009#46 Originally Posted by
gwasabi ↑ lol I was revving mine at red line(6k) for 5 min twice hahahaha
Ouch... Sounds painful! 😲
MGarganoNJ · Apr 15, 2009#47Got some light oscillation a few times today, so I did step 5 again. Think I should just drive it hard for a few days?
gwasabiThread starterHonolulu, Hawaii · Apr 15, 2009#48When do you get the oscillations? while driving or while in idle?
MGarganoNJ · Apr 15, 2009#49At start-up when it's cold it oscillates 4-5 times and then stays around 3k for about 30 seconds, then calms down to normal. I get oscillations sometimes when driving too.
gwasabiThread starterHonolulu, Hawaii · Apr 15, 2009#50hm....did u check for air in your radiator hose?