I did not. How should I do that?Originally Posted by gwasabi ↑hm....did u check for air in your radiator hose?
Tricking the ECU to Relearn AF map
105 posts · 61,384 views · page 2 of 3
Replies continued
Open the radiator cap and turn your car on and wait till all the bubble comes out. usually about 3-5 min.
Ok... will try that now
I got the oscillation at start-up and the fluid only bubbled for a second or two... then the coolant started rising and spilling out so I put the cap back on.
good good
now try the procedure
now try the procedure
Go straight to step 5? Or start by disconnecting the battery for a while and then do step 5?
Disconnect the battery first to reset the ECU
Ok I'll disconnect the battery overnight and then start fresh tomorrow
wait for the results buddy
No oscillation at first start-up after reconnecting the battery, but I revved it heavy for a few minutes anyway. Still no CEL, but getting minor oscillation randomly when driving.
:( sorry to hear that keep us mainly me posted lol
Now I got CEL 3 times today as well as start-up and random oscillation :(
:( o man keep hope alive
... make that four times with the CEL, including heavy start-up oscillation. Also, when I press or release the gas pedal, the car jerks, like it's jumping. I'm quickly getting fed up with this TB. Ideas?
The jerking is normal. heavy DFTS.
That's wierd that method work for me with no oscillation problems....hmmmmm....Try driving couple more days and see if the ECU learns by itself
That's wierd that method work for me with no oscillation problems....hmmmmm....Try driving couple more days and see if the ECU learns by itself
yea mine jerks sometimes too. How long haveyou been driving on it? I forgot if you did the chip swap or not...
No, I didn't do the chip swap and I don't want to, if I can avoid it. I'd hate to crack open the original TB since it's got less than 2,000 miles on it. It's weird cuz the jerking just started out of nowhere, along with the CEL.Originally Posted by Yoda ↑yea mine jerks sometimes too. How long haveyou been driving on it? I forgot if you did the chip swap or not...
What's 'heavy DFTS'? I disconnected the battery again overnight and will start over today. I'll try driving it for a few days if I get any of these problems again.Originally Posted by gwasabi ↑The jerking is normal. heavy DFTS.
That's wierd that method work for me with no oscillation problems....hmmmmm....Try driving couple more days and see if the ECU learns by itself
One of the reasons i got rid of mine. I couldn't get the CEL off👎. I did everyting possible, always got a CEL, i went 2 days at the most, before it came back on. I'll try this mod again in a few months, hopefully someone would have come up with somehthing else to get rid of the CEL, i did the chip swap and everthing. Nice mod, though just don't like driving around with that light on
Originally Posted by MGargano ↑... make that four times with the CEL, including heavy start-up oscillation. Also, when I press or release the gas pedal, the car jerks, like it's jumping. I'm quickly getting fed up with this TB. Ideas?
It's weird how some ppl still gets CELs even after doing the chip swap. I still haven't had a CEL, and I've been driving it pretty hard. 🤷
I think it has something to do with the serial numbers located in the bottom of each TB, but I can't tell for sure.
I think it has something to do with the serial numbers located in the bottom of each TB, but I can't tell for sure.
It's really not even the CEL that bothers me. I have the Scangauge, so getting rid of the light is a breeze. It's the start-up and random oscillation that's killing me. And I'd hate to break open my brand-new TB to do the chip swap and still be stuck with the same problem.Originally Posted by hatchbackkid82 ↑One of the reasons i got rid of mine. I couldn't get the CEL off👎. I did everyting possible, always got a CEL, i went 2 days at the most, before it came back on. I'll try this mod again in a few months, hopefully someone would have come up with somehthing else to get rid of the CEL, i did the chip swap and everthing. Nice mod, though just don't like driving around with that light on
Wait so with the Scangauge hooked up to the car, your telling me the CEL never comes on or it comes on you just turn it off. Have you tried adjusting the idle? It's really simple to open up, nothin in there for you to really damage
No, the CEL still comes on. I just use the Scangauge to turn it off right away. I haven't tried adjusting the idle yet. I'm not worried about damaging the stock TB, I'm just wary of opening it since it's almost brand new with less than 2,000 miles on it. If I open it up to do the chip swap, I want to know it's going to fix the problem.Originally Posted by hatchbackkid82 ↑Wait so with the Scangauge hooked up to the car, your telling me the CEL never comes on or it comes on you just turn it off. Have you tried adjusting the idle? It's really simple to open up, nothin in there for you to really damage
You won't damage the TB if you open it, since all you're really doing is drilling off some rivets. You can always get it sealed back up to OEM specs using a rivet gun (I used screws myself). I think you should give it a shot if you can and see if that solves the problem. Won't take more than 10 mins to do the swap.Originally Posted by MGargano ↑No, the CEL still comes on. I just use the Scangauge to turn it off right away. I haven't tried adjusting the idle yet. I'm not worried about damaging the stock TB, I'm just wary of opening it since it's almost brand new with less than 2,000 miles on it. If I open it up to do the chip swap, I want to know it's going to fix the problem.
Then again, you may want to adjust the idle screw first, which is even easier to do.
I guess I'll give the chip swap a try if the problems come back. I reconnected the battery and got no CEL or oscillation on start up this morning so I'll give it a few days *fingers crossed*Originally Posted by tk-421 ↑You won't damage the TB if you open it, since all you're really doing is drilling off some rivets. You can always get it sealed back up to OEM specs using a rivet gun (I used screws myself). I think you should give it a shot if you can and see if that solves the problem. Won't take more than 10 mins to do the swap.
Then again, you may want to adjust the idle screw first, which is even easier to do.
No CEL but do you get the oscillation?Originally Posted by tk-421 ↑It's weird how some ppl still gets CELs even after doing the chip swap. I still haven't had a CEL, and I've been driving it pretty hard. 🤷
I think it has something to do with the serial numbers located in the bottom of each TB, but I can't tell for sure.
I get minimal oscillation (~300 RPM at the most) while running warm. Not too concerned about it myself. Pretty much the same as stock.Originally Posted by MGargano ↑No CEL but do you get the oscillation?
please do you are my only hope lol
I wish you all the luck in world and I hope this solves your problems. For me, after 3 days, the oscillation keeps getting worse and I've gotten several CELs. The chip swap is next on my to-do list.Originally Posted by kustom play ↑well looks like good news
so i disconnected the battery for about 3 hours
came back and hooked it up started it up, it oscillated a bit then came down to normal
so i waited about 5 mins after that, then reved it up for about 3 more mins
after a while of reving the car started oscillating again so i stopped and let it settle
then i reved it back up for another 2 more mins and then went for a drive
i drove about 110 miles today with no CEL or no problems
looks like im in the clear
i hope it fixes the problem
Do you still get the high cold idle with the tC throttle body?Originally Posted by Yaris T-Sport. ↑hehe, should have done the chip swap in the first place, I'm now running with the 2.4 L Tc TB ( a little more bigger than the 1zz TB, yet a little more power ) with the 1nz chip for over a month with trouble free runs, no cel, no oscillation what so ever.
Was that all nothing esle special done? I might just jump on this if no cel. Did everything work fine when you first put it on and what year exactly did you get?Originally Posted by Yaris T-Sport. ↑yes, which is normal due to the bigger TB opening, about 2.5k, then it sattles right away to 700s
Yes, and I swapped the chips.
did everybody trim the OEM TB gasket to allow more air flow as t-sport did?
I did. That gasket is a joke. I find it hard to believe that it does anything at all.Originally Posted by t0m4s ↑did everybody trim the OEM TB gasket to allow more air flow as t-sport did?
how to have more air to flow in to a N/A engine?
last time i drove a lancer the swap is easy as the TB is run by a cable but the new Yaris TB is drive by wire, understand to do a swap for TB is not that easy any more...
Is there any TB is direct swap in for Yaris engine?
Do we need to mod the TB plug to fit in the new TB?
Will the ECU have any issue to the new TB?
last time i drove a lancer the swap is easy as the TB is run by a cable but the new Yaris TB is drive by wire, understand to do a swap for TB is not that easy any more...
Is there any TB is direct swap in for Yaris engine?
Do we need to mod the TB plug to fit in the new TB?
Will the ECU have any issue to the new TB?
there are three threads dedicated to this subject. in this subforum.Originally Posted by xbalance ↑how to have more air to flow in to a N/A engine?
last time i drove a lancer the swap is easy as the TB is run by a cable but the new Yaris TB is drive by wire, understand to do a swap for TB is not that easy any more...
Is there any TB is direct swap in for Yaris engine?
Do we need to mod the TB plug to fit in the new TB?
Will the ECU have any issue to the new TB?
That's because you have air in your radiator hose. What I suggest is take the radiator cap off and run the car in idle until the bubbles don't come up. the fluid should overflow a little and then when it's settled just pop the cap back on.
Also the Random Oscillation is due to the ECU trying to learn what to do with new TB. Did I mention that this method only works for manual cars? anyway, IF you drive around and get random oscillation just start driving a little harder for a while the opscillation should go away. If it doesn't turn the car off then on right away and it should go away. It happened to me for the first few days but after that it was gone. I have the TB on my car right now and I have NO PROBLEM what so ever with the new TB. No cel, No Oscillation. been like that for almost 5 months now
That ar in the radiator hose part is VERY VERY IMPORTANT! I think i should edit the first post lol
i hope so too i am still waiting....🙄
Just keep driving with the lights on eventually it'll go away
You are just getting a CEL correct not a CEL + oscillation?Originally Posted by kustom play ↑just turned off again
so hopefully it stays off at this point
Thats probably due to the Coolant just drive around for a bit and let the coolant settle. It'll eventually just go away
I FORGOT AND AM TOO LAZY TO REREAD DID YOU DO THE CHIP SWAP AND WHICH TB WAS IT AGAIN AND YEAR...
No I didn't do the chip swap I don't think kustom play did either
i can not find it on ebay.....LAME
Dammit mine started oscillating again and hard 😢 No CEL just hard oscillation like 1-4k rpm while driving.
wo wo wo wo thats not sexy
That was my issue I just said fuck it and sold it.Originally Posted by PHXDEMON ↑Dammit mine started oscillating again and hard 😢 No CEL just hard oscillation like 1-4k rpm while driving.
Yeah I think I might do the same 🙁 It sucks because on wednesday it ran flawlessly to work and back and then it just started happening again for no reason. I really want to figure this out and get it fixed though because there is definately a big power difference with it on. Did your oscillate randomly or is it like mine where sometimes you start it up and it runs fine but sometimes you start it up and it immediately starts oscillating?Originally Posted by AlexNet0 ↑That was my issue I just said fuck it and sold it.