Yarisworld Archive

Yaris dies in carwash!

40 posts · 10,809 views

RS_91CAMAROOriginal postAPPLE VALLEY,MN · Mar 13, 2009#1
Ok so not every time i go to the carwash but more than once my car has just died. It will start right back up but some times i have to give it some gas to keep running. Its a 08 yaris and i have no clue whats going on. Any one else have this problem? I do have the simota intake maybe this is my problem?

Replies 39

LtNoogieWest Hills, CA · Mar 13, 2009#2
Your intake filter may be getting soaked. My aFe filter gets wet and once I threw a CEL. I need a way to protect it the next time I take it to the carwash.
ka0sxCA east bay · Mar 13, 2009#3
i would think that all the water/soap might be finding its way into the intake. The soap would clog up the intake until it drys...
RS_91CAMAROThread starterAPPLE VALLEY,MN · Mar 13, 2009#4
Thats what i thought but i would think this would be more common. Maybe ill put my stock airbox back on and see what happens.
CorzySouth FL · Mar 13, 2009#5
Are you going through a touch-free car wash that uses pressure washers or just a traditional car wash?
RS_91CAMAROThread starterAPPLE VALLEY,MN · Mar 13, 2009#6
Yeah the touch free.
TinyGiantRochester, NH · Mar 13, 2009#7
i go touchless with stock box and have never had that problem
dngzvancouver · Mar 13, 2009#8
u could plastic wrap the intake, takes 2 seconds... then wash car urself =)!
MUSKOKA800Chatham, Ontario, Canada · Mar 13, 2009#9
Yup, sounds like that cold air/water intake is working just dandy.

See post in Canada forum where Adrian hydro-locked his engine due to custom intake.
LtNoogieWest Hills, CA · Mar 13, 2009#10
Originally Posted by RS_91CAMARO ↑
Thats what i thought but i would think this would be more common. Maybe ill put my stock airbox back on and see what happens.
The stock airbox shields the filter somewhat. Many of the SRI kits and the aFe kit has the filter right below the hood seam.

They hand wash at my carwash and then run it through the high power water jets to rinse. I believe that's when the water is being forced through the hood seam and onto the filter.

I'm thinking of putting a strip of door edging on the hood near the filter to see if that will take care of it.
MadMaxSan Antonio, Texas! · Mar 13, 2009#11
Originally Posted by RS_91CAMARO ↑
Thats what i thought but i would think this would be more common. Maybe ill put my stock airbox back on and see what happens.
There's your problem right there, your aftermarket airbox is sucking up water...

What setup are you running?

Cheers! M2
RS_91CAMAROThread starterAPPLE VALLEY,MN · Mar 13, 2009#12
Yeah i have the SRI not the cold air. I think ill try the strip of door edging on the hood idea.
CorzySouth FL · Mar 13, 2009#13
or you can get a shield to go on the filter/intake. the door edge on the hood probably doesn't look all that cosmetically appealing.
supmetSouthern California · Mar 13, 2009#14
Like others have said, its most likely your air filter. My girlfriends jetta use to die in every car wash, and sometimes even if you drove through a puddle.
MadMaxSan Antonio, Texas! · Mar 13, 2009#15
I had a Neuspeed p-flow with a K&N on my old Passat, during extremely wet or damp weather it would suck up moisture and "flame out" the engine, kicking off a CEL. Plus it played hell with my MAF. Whereas it did sound cool and felt like it gave the motor more pull, it was a PITA to keep clean in bad weather (and this car spent three winters in Belgium).

Cheers! M2
LtNoogieWest Hills, CA · Mar 13, 2009#16
Ok, I bought some clear door edge strip moulding. I'll put it on tomorrow morning before the car goes through the car wash. If it solves the wet filter problem, I'll take pictures so you can see if it looks stupid. If the filter still gets wet, no pictures.
silver_echoSpokane, WA · Mar 13, 2009#17
what about putting in a vent for the water to go to... kind of like the shop vac ball system that keeps water out of the shop vac motor
lilredrocketDFW, Texas · Mar 13, 2009#18
I have the Simota CAI and don't have any problems with water
HTM Yarissouth Carolina · Mar 13, 2009#19
UMMMM , ....why do you leave the car running ?
lilredrocketDFW, Texas · Mar 13, 2009#20
Tunnel wash
KRAZGRLOrange County, CA · Mar 13, 2009#21
Be careful with this. The reason I have the Yaris is because my civic si's motor blew when it was really raining a month ago (cold air intake sucked up water from a large unavoidable puddle).
LtNoogieWest Hills, CA · Mar 13, 2009#22
Originally Posted by HTM Yaris ↑
UMMMM , ....why do you leave the car running ?
The car's not running when I send mine through the carwash. The track monster machine pulls it through the tunnel.

Two guys who do not make enough money scrub it with soft brushes on poles. That's followed by a high flow rinse and then a light rinse. I think the water is wetting the filter during the high flow rinse.
LtNoogieWest Hills, CA · Mar 15, 2009#23
Originally Posted by LtNoogie ↑
Ok, I bought some clear door edge strip moulding. I'll put it on tomorrow morning before the car goes through the car wash. If it solves the wet filter problem, I'll take pictures so you can see if it looks stupid. If the filter still gets wet, no pictures.
Scratch that idea. The filter still got wet. Here's some pictures of what I tried. I think the gap is still too big between the hood and fender and bumper.

Or, I might try backing it out the moulding a little to fill the gap more.

Picture lost · i426.photobucket.com
LtNoogieWest Hills, CA · Mar 15, 2009#24
Maybe stuff 1 foot of nylon rope in the gap right before going to the carwash.

Rain does not pose a problem.
thebarberGrand Rapids, MI · Mar 15, 2009#25
diy powerwash ftw
LtNoogieWest Hills, CA · Mar 15, 2009#26
Originally Posted by thebarber ↑
diy powerwash ftw
Yeah, but they clean all the windows on the inside, vacuum and dry.

I'm just a lazy ass.🙂
lilredrocketDFW, Texas · Mar 15, 2009#27
^Me too. $40 wash hand wax and full detail with another free wash in a week! Can't beat that.
LtNoogieWest Hills, CA · Mar 15, 2009#28
Yikes! To me $9.99 every two weeks is too much.🙂
YarisSedanCalifornia - Bay Area · Mar 15, 2009#29
Or you could just do this.....
Picture lost · www.geocities.com
AlexNet0Rockland, ME · Mar 16, 2009#30
clean bays like that on DD's here are impossible with the road salt and sand, constant dirt, etc, id love to keep mine clean, it lasts about a 3 days.


anyway how are those afe's in the car wash?
YarisSedanCalifornia - Bay Area · Mar 16, 2009#31
I put a seal between the hood and bumper so no water gets in anymore to my intake.
RS_91CAMAROThread starterAPPLE VALLEY,MN · Mar 16, 2009#32
Thats what im gonna do!!! Yarissedan What did you use and where did you get it?
anonymous userwindward oahu · Mar 16, 2009#33
Originally Posted by YarisSedan ↑
I put a seal between the hood and bumper so no water gets in anymore to my intake.
Actually the way are hoods are, i don't think the sedan's have this problem.
Wow, for once a sedan beats the LB at something, eh?
thebarberGrand Rapids, MI · Mar 16, 2009#34
Originally Posted by YarisSedan ↑
I put a seal between the hood and bumper so no water gets in anymore to my intake.
neither does any cool air! lol

as for winter driven cars....i would do a major spring clean in my trix after all the snow was gone and it'd usually last a month or two....just used simple green degreaser (cover the alternator, air filter, and battery) and then hose down the engine bay....super clean, super easy
PHXDEMONPhoenix, AZ · Mar 16, 2009#35
This is why I always handwash my car myself 😁
YarisSedanCalifornia - Bay Area · Mar 16, 2009#36
I hand wash my car. I did notice after it rains. WHen i open my hood there is water in the area if the afe intake. So decided to just seal it up extra good as a precation. If you notice when you open the hood of the car you can see the street floor below. My car is lowered already and the air going through the grill causes a draft from the empty space below allowing cool air to go through. Ever notice when you open one window in your house it lets some cool air in but if you open another one across the other side it creates a nice cool draft that cools even better. I think its the same concept. I dont think putting a extra seal trapping water and air at the hood bonnet is going to make any difference in engine bay temperature. Also if anything would make the car slightly more areodynamic since there isnt that drag anymore.
LtNoogieWest Hills, CA · Mar 16, 2009#37
Originally Posted by YarisSedan ↑
I put a seal between the hood and bumper so no water gets in anymore to my intake.
Where did you buy the seal? Do you have a manufacturer and product name or part number?
YarisSedanCalifornia - Bay Area · Mar 16, 2009#38
i got it from some place called softseal. They sell all sorts of automotive weather seals. Do a search. Another member posted the part number for it before.
LtNoogieWest Hills, CA · Apr 4, 2009#39
Thanks to 1NZYaris1, I put the bonnet seal he sent me around the edge of the engine compartment. After going through the carwash, I opened the hood and the aFe filter appeared to be dry. No CEL.

Afe intake feed back required.
1NZYaris1New Zealand · Apr 4, 2009#40
Originally Posted by LtNoogie ↑
Thanks to 1NZYaris1, I put the bonnet seal he sent me around the edge of the engine compartment. After going through the carwash, I opened the hood and the aFe filter appeared to be dry. No CEL.

Afe intake feed back required.
does that mean you are no longer going to send me your S/C 😆