Yarisworld Archive

Inverting an LCD

91 posts · 20,876 views · page 1 of 2

Sodium DuckOriginal postWestern Mass. · Mar 7, 2009#1
I've seen a few tutorials on how to do this online, anyone done it?

I'd like to invert the gas gauge.

Replies 90

GeneralDon7Frederick, MD · Mar 8, 2009#2
There was one member on here, who got it done by someone, else, and all they used was a film that you could buy that inverted it, ill post the link if i can find it.
Sodium DuckThread starterWestern Mass. · Mar 8, 2009#3
Yes, I believe you can just buy any LCD polarizing film. I've found a few places that sell it, sorta expensive.
wsladaritzBenton, AR · Mar 8, 2009#4
That's interesting....
Sodium DuckThread starterWestern Mass. · Mar 8, 2009#5
Yea, I found that site last night. I think I may go to the dollar store and buy some calculators to practice on.
Sodium DuckThread starterWestern Mass. · Mar 8, 2009#6
Umm, I'm no electrician. How would I go about reversing the cathode input? Would that be easier or give a better result?
bzinn 1University Place,WA · Mar 8, 2009#7
contact this person from Scion Life www.garage1217.com he does all this kind of stuf for the Scions and has all the materials you will need and can give you a how to do it as well...he is really cool.
the_bossMontreal Qc · Mar 8, 2009#8
i have done that when in was in primary school with a calculator, i was able to take the lens in front of the lcd display and turn it (side facing lcd display goes outside and outside goes inside) and the color was inverted white digits and black background

not sure how the gas gauge is but would probably work too
enobmort42Denver, CO · Mar 8, 2009#9
isn't it factory on some models? i'd like to do it, myself. this and the radio color were the two biggest "cons" in getting the car i did.
Meteorite_MartyWaterloo, Ontario, Canada · Mar 8, 2009#10
Where do you get the LCD polarizing film to even take on this job?
Sodium DuckThread starterWestern Mass. · Mar 10, 2009#12
Ha, I just bought a 1$ calculator at Walmart to try it out, very easy to do. I'm going to buy a sheet of polarizing film to do this.

Is there a way to know what the orientation of the film is so I don't need to temporarily plug the gauges back in to the car?
CTScottUSA, CT · Mar 10, 2009#13
Theoretically, you could use your $1 calculator as a test fixture for the orientation. After removing its film, place the original Yaris film over it, and note the effect, then remove it and rotate the new film over it until you see the opposite effect as the Yaris film.
Sodium DuckThread starterWestern Mass. · Mar 10, 2009#14
Found this on the site you posted before Scott:

How can I tell what the polarization axis is for a linear polarizer?
The axis of a linear polarizer determines the plane of polarization that the polarizer passes. There are two ways of finding the axis of a polarizer. A simple method is to start with a known polarizer with a marked axis. Place both the known and unknown polarizer together and transmit light through them. Rotate the unknown polarizer until no light passes through the pair of polarizers. In this orientation, the unknown polarizer's axis is 90° from the axis of the known polarizer.

If a known polarizer with a marked axis cannot be found, the axis can be found by taking advantage of the Brewster effect. When light reflects at glancing incidence off of a non-metallic surface, the S-polarization is reflected more than the P-polarization. A quick way to do this is to look at the glare off of a tiled floor or another non-metallic surface. Rotate the polarizer until the glare is minimized. In this position, the polarizer is oriented so that the axis is vertical. As an example, sunglasses use polarizers that have the polarization axis vertically oriented.
Sodium DuckThread starterWestern Mass. · Mar 10, 2009#15
I think the 2"X2" sheet there will just almost perfectly fit the LCD btw. I just ran down and did a quick measurement on the car, and it looks like it's just a bit under 2" wide. For 9$ you can't go wrong.
Sodium DuckThread starterWestern Mass. · Mar 10, 2009#18
Edmunds Optics does not have an adhesive backing on them.
CTScottUSA, CT · Mar 10, 2009#19
Correct. The LCDs I inverted had a metal frame around them, so I was able to simply sandwich the ES film. If you go with a non-adhesive film and find that the LCD doesn't have a frame, you can simply tape the film around the edges, making sure that the tape doesn't extend past the frame coverage.
Sodium DuckThread starterWestern Mass. · Mar 10, 2009#20
Much to contemplate now. haha
Meteorite_MartyWaterloo, Ontario, Canada · Mar 10, 2009#21
My gas gauge is already inverted, from factory. Black background with white text.

I want to do my radio to match it. I have already done a white LED replacement on my radio (replaced the green LEDs). Currently the radio has a white background with black text, but would like the display to inverted. This way it would match my dashboard displays.
Meteorite_MartyWaterloo, Ontario, Canada · Mar 10, 2009#22
Originally Posted by Sodium Duck ↑
Or they're really big and cheap here.

http://www.3dlens.com/shop/polarizer.php
Which one did you order? Functionalitywise, are they all the same? It looks like they just differ by size and anti-glare.
Sodium DuckThread starterWestern Mass. · Mar 10, 2009#23
I'm just going to go with the Edmund Optics, but I'm not ordering until I go out and pop my gauge cluster out. I want exact measurements of the LCD before I go ordering something.

Like Scott said, some tape will hold it in place fine. I may even do a dab of some silicone adhesive in the corners for a more permanent thing.

Can you post pics of your dash? Are you talking about the black background and green horozontal gas gauge thing? Or I've seen another one that had more of a blue-ish background.
Meteorite_MartyWaterloo, Ontario, Canada · Mar 10, 2009#24
Here are the pictures of my dash.

2 attachments not included in this copy

Sodium DuckThread starterWestern Mass. · Mar 10, 2009#25
Ahh yes, it has that blue-ish background.

I think you'll just have to buy an extra big sheet from Edmunds to cover it all.

Tommorow I'm going to pop my gauge cluster out, take measurements, and order from Edmunds. If I end up needing a bigger sheet, I'll sell the leftovers for cheap.
Sodium DuckThread starterWestern Mass. · Mar 10, 2009#26
Originally Posted by Meteorite_Marty ↑
Which one did you order? Functionalitywise, are they all the same? It looks like they just differ by size and anti-glare.
Some of the ones there are not indicated for use by LCD screens. There are only a few listed that are intended for LCD's. Aside from that, they are based in Taiwain, and I don't like dealing over the seas.
Meteorite_MartyWaterloo, Ontario, Canada · Mar 10, 2009#27
Originally Posted by Sodium Duck ↑
Ahh yes, it has that blue-ish background.

I think you'll just have to buy an extra big sheet from Edmunds to cover it all.

Tommorow I'm going to pop my gauge cluster out, take measurements, and order from Edmunds. If I end up needing a bigger sheet, I'll sell the leftovers for cheap.

Well, I am happy with the dashboard. Its not as "blue" as it looks. Blends nicely into the dark for night driving.

I am going to try and do this for my radio display, to unify the look.
Sodium DuckThread starterWestern Mass. · Mar 11, 2009#28
So it looks like the visible area is about 1 7/8" X 3/4" and the actual LCD itself is about 2" X 1".

Hmm. I'm going to think about it for a couple hours then decide which film to buy. If I get the one from Edmunds, I could simply put the 2" X 2" sheet down and tape/glue the overhang above and below to the plastic case. Then the black face for the gauges would hold the rest down sufficiently I think.
Sodium DuckThread starterWestern Mass. · Mar 11, 2009#29
Forgot to add pics... boink.

4 attachments not included in this copy

CTScottUSA, CT · Mar 11, 2009#30
Originally Posted by Sodium Duck ↑
Forgot to add pics... boink.
Snap some pics of the PCB with the microcontroller, etc. PK's been anxious for someone to post some when they have their combo meter assembly apart...
Sodium DuckThread starterWestern Mass. · Mar 11, 2009#31
... I just got back from putting it back in my car ... Dang!

When I take it apart again to do the film I'll take more pics. To be honest though, I think I'm going to do this mod without taking much apart. All you have to do to gain access to the LCD is pop the front plastic off the gauge cluster, pull the speedo needle (which I was too sissy to pull hard enough on to actually remove for these pics), and take the background off. The LCD is just sitting there. It snaps into place with those four little white indented tabs you see in the pics. Then there are 22 really long pins on the bottom of the LCD that go down to some connector.

Does he want pics of the whole circuit board taken apart, like the people who did the LED color changes to their gauge cluster?
Sodium DuckThread starterWestern Mass. · Mar 11, 2009#32
Good gravy.

NT43-781: $8.00
Subtotal: $8.00
Tax: $0.40
Shipping: $9.32
Total: $17.72

9 bucks to ship me a 2" X 2" piece of paper... I'm going to search around the net and see what else I can find. Even the stuff from Taiwan was only 4 bucks to ship, but they have a minimum $10 purchase thing. Still, it'd only be 14 bucks.
Sodium DuckThread starterWestern Mass. · Mar 11, 2009#33
Sounds cool. I'd like to have temp and MPG be enabled, that'd be snazzy. I'm just going to eat it big and buy from Edmunds anyways, so in a week or so when I take my gauges out, I'll do it.

It's really easy to take the gauge cluster out though, takes about 2 minutes total, just 2 screws. How come you haven't taken yours out?
Sodium DuckThread starterWestern Mass. · Mar 11, 2009#34
I'm assuming that the Canadian Yaris's have the same LCD gauge as the US Yaris's? Can you post a pic up of a gauge with the things you want turned on? I'm just curious.

In the above pics from Marty, you can see the things that the gauge can display, but isn't - if you look closely. I'd like to take a few shots of my LCD and see if I can see them too.

Just want to know what I'm trying to look for.
neo1985temple city · Mar 11, 2009#35
Originally Posted by the_boss ↑
i have done that when in was in primary school with a calculator, i was able to take the lens in front of the lcd display and turn it (side facing lcd display goes outside and outside goes inside) and the color was inverted white digits and black background

not sure how the gas gauge is but would probably work too

BINGO!!! i was just about to say that.. u dont need to buy anything.. just take off the top layer carefully on the lcd and then turn it!!!
neo1985temple city · Mar 11, 2009#36
Originally Posted by PK198105 ↑
except when the sun hits it without the screen you won't see much , you need the screen to prevent washout
that true tho!! but thats how it is with that effect
Sodium DuckThread starterWestern Mass. · Mar 11, 2009#37
Originally Posted by PK198105 ↑
ok in Marty's pics since he has a automatic you can see , the CVT icon and Manual/Tiptronic icon and his clock is shifted to the left. Mine is stick so i can see the MPG, Temp as well as km and miles counters.

I suspect that the automatic display is taken directly from the JDM versions (saves them money by just making one kind and enabling certain functions)
I have an automatic, too. Is it still worth it to you for me to take pics? I don't believe mine has the same things as yours.
Sodium DuckThread starterWestern Mass. · Mar 11, 2009#38
woot!

Yea, all you need to do to get your gauge cluster out is take the side pieces off (start pulling from the bottom). And by side pieces, I mean the long trim piece that has your hazard lights and air bag sensor on them. Then you take the trim piece off the gauge cluster itself. I usually go from the bottom, pulling up from where it attaches above the vents to the top. Then there are just 2 screws and two connectors that easily come out and your gauge cluster is free.

So I guess it's a little more than just two screws... but I can have my cluster out from start to finish in 2 minutes. Everything just pops off easily.
Meteorite_MartyWaterloo, Ontario, Canada · Mar 14, 2009#39
Just "practiced" on a second factory radio I had for the Yaris. Dismantled the LCD and removed the polarizing film. Flipped the film 90 degrees and achieved the inverted LCD display. Of course I have to remove the residue and the old film doesn't stick perfect, but its only a test. I have ordered some new single-side adhesive LCD polarzing film to complete the job. Will post pics when done.
Meteorite_MartyWaterloo, Ontario, Canada · Mar 14, 2009#40
Here's my test phase on my "practice" deck. I only had the width of the rectangle display to use, since I had to turn it 90 degrees to get the blackout effect. I plugged it in, and the text is white (keep in mind, I have done a white LED replacement on my deck already). The bumps and dots you see on the right side of the display is leftover glue residue, which I will clean up later once I put the final polarizing film in place.

1 attachment not included in this copy

Sodium DuckThread starterWestern Mass. · Mar 14, 2009#41
Looks promising so far marty. Where are you getting your film from?
Meteorite_MartyWaterloo, Ontario, Canada · Mar 14, 2009#42
Originally Posted by Sodium Duck ↑
Looks promising so far marty. Where are you getting your film from?
I went with 3DLens.com, 17". I need room to play, since I will be doing 2 decks, plus I need rotation freedom to find out where the polarizing blacks out the display. Their products specifically say for use with LCDs, and have adhesive backing on one side, which will make my installation more like factory. Pricey after the exchange rate and shipping to Canada. I will likely sell my surplus stock to anyone here that wants it.
Sodium DuckThread starterWestern Mass. · Mar 14, 2009#43
I'm really interested to see how it comes out. I ordered mine from Edmund Optics. Just a 2" X 2" sheet... too much money... lol
Sodium DuckThread starterWestern Mass. · Mar 17, 2009#44
Got my film today. I'm going to do the install tomorrow when I have some free time.

PK, I'll try and take some pics for you. I think I know how to get behind the board, but we'll see.
Sodium DuckThread starterWestern Mass. · Mar 18, 2009#45
Pics for PK - very huge. Sorry about the blurriness, they looked a lot cleaner on my camera's display. It doesn't really matter though, there aren't any jumpers to be seen. Zip. Sorry PK. 🙁

Finished inversion pics in a few minutes. Test so far looks good. Not as much contrast as I was hoping for though. The polarizer is a little weak. Maybe some brighter LED's will help?

5 attachments not included in this copy

eTiMaGoBangkok, Thailand · Mar 18, 2009#46
dang, forgot to ask you, is the speedo needle tinted red, or is there a red LED to light it up that color? 😉
Sodium DuckThread starterWestern Mass. · Mar 18, 2009#47
The needle is clear plastic, and seems to have a thin red film that is either on top, or embedded in the plastic.
Sodium DuckThread starterWestern Mass. · Mar 18, 2009#48
I used two small drops of epoxy to secure the film in place.

Very disappointing results. Driving without the plastic cover on the gauges, it was fine. But once the plastic cover went on, the visibility went to shit. I even tried doubling up the polarizers, but it went to black. I guess I'll live with it for now. Maybe I'll just splurge on a cluster with tach - only 600 dollars right? lol

Maybe it will be better at night.

6 attachments not included in this copy

||)) (o) ||\||Southwest PA · Mar 18, 2009#49
^ Its just painted red. You can easily remove it with acetone. Getting to the center of the needle is a different story though.
CTScottUSA, CT · Mar 18, 2009#50
Originally Posted by Sodium Duck ↑
I used two small drops of epoxy to secure the film in place.

Very disappointing results. Driving without the plastic cover on the gauges, it was fine. But once the plastic cover went on, the visibility went to shit. I even tried doubling up the polarizers, but it went to black. I guess I'll live with it for now. Maybe I'll just splurge on a cluster with tach - only 600 dollars right? lol

Maybe it will be better at night.

I think you need to upgrade the backlight LEDs. With the smoked lens in front of the reverse contrast LCD it will require more lumens to have the text be as bright as the background was...