Yarisworld Archive

Installing Blitz Supercharger

197 posts · 38,784 views · page 3 of 4

Replies continued

LtNoogieWest Hills, CA · Feb 25, 2009#101
Originally Posted by whooppee777 ↑
i feel like i never see kurokuma kun post anymore, whats the deal?
She left the forum when some people were joking around and were being a little disrespectful of women.

She posts on the MicroImage Club website, however.
LtNoogieWest Hills, CA · Feb 25, 2009#102
Sometimes I hear it when the blower is not engaged. Like when I'm parked and idling and have the hood open. It's only coming from the passenger side, somewhere along the path of the belt. Garm, Guillermo, and JR could not figure out where the sound was coming from.

One of us will solve it eventually.
LtNoogieWest Hills, CA · Feb 25, 2009#103
If someone with a S/C doesn't know what pre-ignition sounds like, do this:

1. Drive until you're almost empty.
2. Put 2-3 gallons of the lowest octane gas into your tank.
3. Drive without boost for a couple of miles to get that 91 octane out of your fuel lines.
4. Roll down your window.
5. Boost at WOT... that nasty sound you hear is pre-ignition. Don't do this for more than a few seconds.
6. Fill up the rest of your tank with 91 octane.
Doc ZaiusOttawa, ON, Canada · Feb 25, 2009#104
Originally Posted by camelll ↑
Another thing LT have you turned on your defroster or ac on and heard anything while just idling or stopped in gear? Staypuft and I both have experienced this and have not figured it out. Under these conditions we hear a vibration sound. Only happens with ac or defrost and basically idling in park or in gear with foot on the brake. Foot on the break it occurs more often as the rpms are lower. Check it out and let me know.
I totally get this!! I haven't been driving with the 'charger on much during the winter. But at the end of last season, whenever I'd have the A/C on, and the car was idling, I'd get some nasty sounding vibration. Don't need my foot on the brake, but my parking brake would be on so the car doesn't roll away. Anyhow, couldn't locate it. Just sounded like something buzzing against something else. I'll be trying to find it again in the spring.
LtNoogieWest Hills, CA · Feb 25, 2009#105
I hope we're not scaring anyone away from installing the next Blitz kit.
ae92trueno7Edmonton, Alberta · Feb 25, 2009#106
yeah i got the same noise when i first installed my supercharger too... its only when ur at wot....u can hear that noise... then i filled my tank up with 91 octane and added octane booster to my tank.. and the noise is gone.....ive been adding octane booster everytime i fill up and i havent got that noise ever since...
Nexus1155Dorchester · Feb 25, 2009#107
hahaha your'e scaring me, if i ever get one, i hope it runs fine with 93 Octane here, if not i better find an ignition controller, because this ecu is giving me one hell of a time still...
PETERPOOPOahu · Feb 25, 2009#108
hmm...very interesting.
LtNoogieWest Hills, CA · Feb 25, 2009#109
For the record. I don't have any problems with pre-ignition right now. I use Shell V-Power every fillup.
PETERPOOPOahu · Feb 25, 2009#110
You are just running lean right now, correct? Tc injectors will fix this? Did you change your sparkplugs?
LtNoogieWest Hills, CA · Feb 25, 2009#111
I changed to the same spark plugs camelll is using. Maybe I'm just lucky. When the weather heats up and if the engine runs hotter, I'll know if I have a problem then.
Doc ZaiusOttawa, ON, Canada · Feb 25, 2009#112
Originally Posted by camelll ↑
.... I was also told they tuned the jdm version of the kit for 100 octane. ...
I'm pretty sure that the Japanese (and Europeans) have a different octane rating system... I think it tends to be about 5 points higher for the same quality gas. So maybe closer to 95 North American octane might be more appropriate.

I try to always fill up at one of the few local Sunocos... 94 octane! 👍
LtNoogieWest Hills, CA · Feb 25, 2009#113
Wow, we've really threadjacked Whooppee's thread but this should be good info for him to think about.
ae92trueno7Edmonton, Alberta · Feb 25, 2009#114
i'm just using the stock spark plugs... i dont think i will be able to start my car with those plugs.... its like -30 in canada.... haha
LtNoogieWest Hills, CA · Feb 25, 2009#115
Wow, just a few more people from Whooppee's list and we will have a quorum of the YW Boosted Jedi.😆
eTiMaGoBangkok, Thailand · Feb 26, 2009#116
Originally Posted by Doc Zaius ↑
I'm pretty sure that the Japanese (and Europeans) have a different octane rating system... I think it tends to be about 5 points higher for the same quality gas. So maybe closer to 95 North American octane might be more appropriate.

I try to always fill up at one of the few local Sunocos... 94 octane! 👍
yeah there's Octane Number and Research Octane Number, which means some differences... For example our 91 octane here is equivalent to 87 octane in the US, our 95 is your 91, etc...
whooppee777Thread starterMaryland · Feb 26, 2009#117
i havent heard any weird noises. but there is the odd random lean condition which happens cruising on highways. seems like preignition to me. im hoping sparkplugs will fix that. theyre going on tomorrow morning
kurokoma-kunmy own little world · Feb 27, 2009#118
Hmmm... I see my user name has been repeated three times... this has invoked my spirit, so here I am back from The Beyond... 😛

Congrats on your fast install Whooppee! 👏🤘 I was about to be jealous of your success but then your idler pulley fell off! 😉 I think I still win the award for loosest nuts... loooooong story 🙄

I'm also glad--well, not glad--gratified maybe--to learn that the rest of you are experiencing similar tuning issues. I've had a few baffling problems (idle control and voltage fluctuation problems) but in the end these were easily fixed, and unrelated to the pre-ignition. As Long stated, I was getting that distinctive "crackling" sound (sorta like furiously sizzling bacon) the first time hammering the throttle under load in any driving session (very much like what Camelll describes). I drive with it on Low most of the time--no other acceleration issues, just smooth power delivery in every gear. I installed NGK iridium 7 spark plugs before the compressor, and only used 93 octane fuel, so gas treatment was about the only adjustment I could make. Much better, though not gone altogether.

BUT I got the cheapee STP stuff--the Lucas or NOS products are better? Where did you buy?
whooppee777Thread starterMaryland · Feb 27, 2009#119
Originally Posted by kurokoma-kun ↑
Congrats on your fast install Whooppee! 👏🤘 I was about to be jealous of your success but then your idler pulley fell off! 😉
hey it ran with no problem for about 4 hours. if i wasnt so damn tired and excited to just drive the car, i probably would not have tightened the pulley enough.

Originally Posted by kurokoma-kun ↑
I think I still win the award for loosest nuts... loooooong story 🙄
this could probably be taken the wrong way for a random user skimming through the thread. care to elaborate?
kurokoma-kunmy own little world · Feb 27, 2009#120
Originally Posted by whooppee777 ↑
hey it ran with no problem for about 4 hours. if i wasnt so damn tired and excited to just drive the car, i probably would not have tightened the pulley enough.
I was just kidding Whoppee, I was very impressed by the speed and success of your install... my own car was out of commission for more than three weeks 🙁 making mine the slowest install of all so far

Originally Posted by whooppee777 ↑
this could probably be taken the wrong way for a random user skimming through the thread. care to elaborate?
Haha sure! Sorry, I forgot that not everyone remembers I'm female, so I could only be referring to the engine's nuts 😁

During my install the new manifold did not seat properly on the cylinder head, which is why though the nuts felt tight, I had a leak that caused all sorts of problems. In going over every connection for the bajillionth time I pressed down hard on the manifold... it slid those last few millimeters down over the studs at last! and my "tight" nuts were suddenly loose. Torqued them down and problem solved 👍

Later I was having intermittent voltage fluctuation and finally discovered my connection on the alternator was bad. All the vibration basically "walked" the nut right off the terminal post... new nut and lock washer, problem solved again.
Doc ZaiusOttawa, ON, Canada · Feb 27, 2009#121
Originally Posted by kurokoma-kun ↑
I was just kidding Whoppee, I was very impressed by the speed and success of your install... my own car was out of commission for more than three weeks 🙁 making mine the slowest install of all so far
Oh... I think we're about tied for slowest, KK!! 😛 Glad to see you back!

Sizzling bacon, huh? Wow... I've never had any of the issues you guys are all talking about. I got my own weird set of issues... I'm pretty sure they're fuel related. Or a bad crimp somewhere. Worst thing is that it's totally intermittent! 🙁

Anyhow... Blitz on! 😁
whooppee777Thread starterMaryland · Feb 27, 2009#122
i must be deaf cuz i dont hear this sizzling bacon noise when i'm boosting. but i had been filling up with premium probably 3 weeks before i installed.
turboyarisSouthern New Jersey · Feb 27, 2009#123
it sounded like a million screaming babies when he was pulling outta my driveway hahaahha
LtNoogieWest Hills, CA · Feb 27, 2009#124
Today was hot and I ran the air conditioner today. S/C was set to OFF. That growling rattling noise was back. One of us needs to figure out what is causing that.
PETERPOOPOahu · Feb 28, 2009#125
You guys are scaring me.
LtNoogieWest Hills, CA · Feb 28, 2009#126
Turbo kits scare me. They all seem custom. You're kinda on your own.

We Blitz owners all share identical setups and can help each other out.
LtNoogieWest Hills, CA · Feb 28, 2009#127
Originally Posted by camelll ↑
There are 2 different distinct noises that I hear with mine. The first is what we have determined to be pre-ignition and the second one is when the defrost or ac is on regardless if the sc is on or not and it sounds like a vibration that comes and goes with the engine loping when the ac compressor comes on and then goes off. Is this the noise you are talking about LT?
Yes. I had a friend in the car and he thought it sounded like some kind of vibration under the floor board. Wierd.
kurokoma-kunmy own little world · Feb 28, 2009#128
I'm also getting the buzzing/vibe that can sometimes be felt and/or heard from floor, pedal, and/or shifter.

For a while this was happening like clockwork, right at 3k rpm. Now it happens seemingly at random.

I've been assuming it's the exhaust heat shield rattling... just the fact that it affects the shifter, because I believe the cables go through the firewall right behind it. Not sure how you A/T drivers trans is set up.

After seeing the way the s/c additional vibrations quickly took apart anything I did not put back together well, I'm prepared to have to track down and fix things like this from time to time. I'm also prepared to live with a noise that does not affect performance or get worse--that's just the car talking to you
whooppee777Thread starterMaryland · Feb 28, 2009#129
Originally Posted by turboyaris ↑
it sounded like a million screaming babies when he was pulling outta my driveway hahaahha
that was the pulley i put on to replace the one that flew off into traffic. i cant stand it, next week i am going to go to other part stores to find a heavy duty pulley that wont squeal. the pulley thats on there right now is so much lighter than what used to be on there. theres a 60 day lead time for the pulley from blitz, i cant go 60 days with that squealing pulley
kurokoma-kunmy own little world · Feb 28, 2009#130
Originally Posted by Yaris T-Sport ↑
does it noise appear when you rev it in netural with ur SC set to ON? if it only does it under load or while you are driving
2 separate noises. the pre-ignition i don't have anymore, looks like the fuel additive has done away with it.

the buzzing is below the floorboard... does not happen that often now and for me it does not affect performance in any way, just slightly annoying.

To anyone who wonders if the tinkering is worth it: I've had small struggles but when the s/c unit is running as it should and all associated components of intake/exhaust/drivetrain/suspension are in harmony, I'd say you can expect very smooth transfer of power to the wheels at launch (in a straight line anyway), excellent throttle response, effortless rev matching, light steering, nice weight balance--the extra weight in front seems to help handling more than I thought it would.

That's why I drive with the thing set on Low all the time, as I find the power easier to modulate around corners that way--it makes my 25-mile commute on curvy semi-country roads over low hills like drifting in a dream through low speed torque land, lol.
LtNoogieWest Hills, CA · Feb 28, 2009#131
I'll be in medium speed torque land at this weekend's autocross.

KK, have you raced the S/C'd car yet?
kurokoma-kunmy own little world · Feb 28, 2009#132
NO, not til end of March, our first test n tune grr. Theres a new regional SCCA class here--STM--its SM on street tires basically. Ill be running in that on RT 615s. Planning on taking back seat out also.

Good luck Long 😈
LtNoogieWest Hills, CA · Feb 28, 2009#133
It sucks that I have to move up to SM because of the S/C.

Oh well. I'll switch to RT 615 later in the summer or to Kuhmo XS.

Whooppee, you're going to drag race yours, right? You're trying to beat the best 1/4 mile time for a Yaris?
whooppee777Thread starterMaryland · Feb 28, 2009#134
im dying to race one of my friends with one of the new civic si's. they still dont think i can beat them.
LtNoogieWest Hills, CA · Feb 28, 2009#135
On a track, right?

Just warn them that if they get behind you, that you tend to eject parts from your engine bay as obstacles for them.😆

Sorry, I could not help myself.
LtNoogieWest Hills, CA · Feb 28, 2009#136
Originally Posted by Yaris T-Sport ↑
mmm the new SI will hit 60 MPH in around 7 sec with a MT.......😕
Still waiting for one of you MT S/C'd guys to make a 0 to 60 video.
kurokoma-kunmy own little world · Feb 28, 2009#137
Originally Posted by whooppee777 ↑
im dying to race one of my friends with one of the new civic si's. they still dont think i can beat them.
mmmm, those civic si's are pretty quick, so much depends on the driver though... a guy from out of town brought one to an auto-x last year and the only one in sts who could beat him was driving an older sentra se-r.

but i dont know anything about drag racing really 😳 and i don't even know my current 0-60 time
BLAZINBLUEVITZNEW YORK · Feb 28, 2009#138
Originally Posted by whooppee777 ↑
im dying to race one of my friends with one of the new civic si's. they still dont think i can beat them.
😆 im assuming you'll be doing this with those new lightweight 15's.
kurokoma-kunmy own little world · Mar 1, 2009#139
Originally Posted by camelll ↑
...So the stp is crap according to them. One bottle of the lucas will get a 10 gallon tank of 93 to 96.6 they said best bang for the buck...
Well, many thanks for the tip camelll and yaris tsport on the lucas oil product! It has definitely done the trick, just went up the highway ramp where I first noticed the pre-ignition sound and its totally gone. 👍

No wonder the STP is like a buck a bottle... if anyone sees the lucas fuel additive on sale, please post 🙂
PETERPOOPOahu · Mar 1, 2009#140
glad to hear the success story!
LtNoogieWest Hills, CA · Mar 1, 2009#141
I dumped a bottle of Octane Boost 104 in the car this morning before the autocross event. Even with the warm weather and a passenger, I did not have any pre-ignition.
LtNoogieWest Hills, CA · Mar 1, 2009#142
Yaris t-sport heard the A/C noise coming from my car today. He thinks it's coming from a rattling heat shield somewhere along the exhaust. I'll find it next weekend.
LtNoogieWest Hills, CA · Mar 1, 2009#143
My mechanic did it but I think the heat shield is still there. Why? Was he supposed to remove it?
cali yarisCanoga Park, CA · Mar 1, 2009#144
The heat shield will not go back on with an aftermarket header (because an important bracket is welded to the stock header).

It's easy to see if it's on there by looking directly behind the motor - if you can see the header, you don't have a heat shield on there.
Doc ZaiusOttawa, ON, Canada · Mar 2, 2009#145
I still have my stock header + heat shield. I noticed this rattling as soon as I was done the install... I can't imagine that it was just coincidence that my heat shield got loose right at the same time! Must be something else. A/C coolant lines vibrating together maybe? They run into the cabin.
thebarberGrand Rapids, MI · Mar 2, 2009#146
i have some under-hood rattling these days at 600rpm-ish idle....i dont have a/c or any mods right now....not sure that helps much
SaggioSeattle WA, · Mar 10, 2009#147
Still no pics...
rpalaiFlorida, USA · Mar 14, 2009#148
Originally Posted by whooppee777 ↑
it works. only took 9 hours feels AWESOME! pix and video soon to come
Hello! My mechanic just finished installing the Blitz Supercharging system on my 2008 Yaris. Well, all except for wiring up the fuel controller module. There is a problem...the wiring instructions SUCK!! They are not only unclear, but they seem to be reversed (upside down) with respect to the onboard sockets on the OEM ECU where the wires need to be connected to. Both he and I are afraid to wire it up and trun it on for fear of frying the ECM and/or the fuel controller since the included wring diagram makes no sense at all. It shows wires going to ports on the ECM that are blanks; like I said, it appears to be drawn upside down....not sure...? I would GLADLY pay you if you could help me out with the correct wiring for the controller as I can not get my car finsished as it stands and I need to get it back from m mechanic's shop. My wife ia all over me and it is actaully the car that she uses daily and she is screaming mad at me....I tried finidng out from Garm who sold it to me, but he does not know either as he just sells these systems and has not installed them...Can you help? Thanks! Rich Palais rpalai
LtNoogieWest Hills, CA · Mar 14, 2009#149
If you want the connectors and pins to make sense, you actually have to look down on the connector through the wires. I believe that is the orientation.

Or, you can do the mental gymnastics and realize that it is reversed. I think the diagram shows the pins in relation to the ECU if you look down on the ECU.
cali yarisCanoga Park, CA · Mar 14, 2009#150
Thanks for helping my customer out -- I just don't have an answer for him.

Richard, if you could be specific about which two wires you are having trouble placing, that would help - colors?