Yarisworld Archive

Tamago's guide to ultimate yaris handling

99 posts · 460,942 views · page 2 of 2

Replies continued

tropicalsuckerpunchunder there · Mar 22, 2009#51
Post #1 of this thread doesn't show me yaris handling information?
d1nzfeasia · Mar 22, 2009#52
canister like this?
Picture not included in this copy
AND this?
Picture not included in this copy
😁
HTM Yarissouth Carolina · Mar 22, 2009#53
How the fudge did I miss this kick ass thread ?

🙇🙇🙇🙇🙇🙇
CtrlAltDefeatIndianapolis IN · Jul 24, 2009#54
Originally Posted by Tamago ↑
the information given in this post is here merely to provide a starting point for your future autocross or road racing endeavors. this is not the end-all-be-all of information on the yaris. as i come across exact situations related directly to the yaris i will add them to this post
uhh... where did the info go? 🤷🤷🤷
TamagoThread starterOff Grid · Jul 24, 2009#55
fortunately i kept a backup. PM me and i'll email it to you. until i know it won't get deleted again without explanation i'm not going to post it in the original post.

edit: lol look! it magically re-appeared.
TamagoThread starterOff Grid · Sep 2, 2009#56
Originally Posted by Loren ↑
Wider track usually means more grip (for various reasons). So, widening the track in the rear would make the rear stick better. Not really what most of us are fighting for, with a FWD car, you want more grip in the front.

The rear hub spacers are purely a cosmetic mod. (not to be confused with alignment shims)
Originally Posted by kngrsll ↑
so we ran a track day with the spacers installed. although there was rubbing on the streets, with the spare and other junk removed, there was no longer any rubbing. If you remove a little weight, you can get away with the 15x7 +10.

The really important thing is how the car drove. My co-driver and i did 2 sessions a piece. He has driven the car at ever event that i have, so his feed back is just as valuable. The spacers had a noticeable increase in rear stability. It made it a little easier to carry speed into the corner without the rear wanting to chase you, so turn-in speeds may have been a little faster. What was more important was stability increased the "trust" in the car in the corner. As you may know, if you feel confident about the car, you will be able to drive it well.

Since I needed to remove the spacers for street use, i pulled them off before the last session. The rear end felt a little more unstable (duh) and if you gave the same inputs as before, the back end would tend to slide a little more. That may be good for autox, but not for the track. As easy as the are to take on and off, i may swap them on depending on the type of course. Tight courses may favor the spacers out, while the more open courses (like the one we were one) would be better with the rear spacers in.

All in all, i think they helped with the stability of the car. If i were not running such low offsets, i would continue to use them. If you have anthing more than a 35 mm offset, they are a no brainer, they easily fit and increase rear stability. The 10 mm should put the track in the front and rear dead even, while the 13 mm spacers may make the rear track greater than the front.

Great mod, track approved :)
taken from : Installed 10mm PG spacers on a 15x7 +25 wheel
fmicleSan Jose, CA, USA · Nov 2, 2009#57
I am looking for a little advice. So the wheels I have now on the Yaris were the very first mod I did and I must say, I didn't do my homework before buying. So I ended up getting 16x7" with 195/50-16 tires. After finding this kick-ass thread and doing more reading on the subject, I'm thinking about going back to 15x6.5" with 195/55-15, as recommended here 🙂

Now, I also have lowering springs (NF210) and shocks on my list, which is the next thing I had in mind, but I was wondering, would it make more sense to replace the wheels first and then get the springs and shocks or get the springs/shocks first?
TamagoThread starterOff Grid · Nov 2, 2009#58
Originally Posted by fmicle ↑
I am looking for a little advice. So the wheels I have now on the Yaris were the very first mod I did and I must say, I didn't do my homework before buying. So I ended up getting 16x7" with 195/50-16 tires. After finding this kick-ass thread and doing more reading on the subject, I'm thinking about going back to 15x6.5" with 195/55-15, as recommended here 🙂

Now, I also have lowering springs (NF210) and shocks on my list, which is the next thing I had in mind, but I was wondering, would it make more sense to replace the wheels first and then get the springs and shocks or get the springs/shocks first?
do the suspension first, and then worry about wheels/tires after.

remember, the tire itself is the most important mod. size is less of an issue, whereas the tire compound itself is VERY important. don't go cheap on tires, and it'll reward you.
kngrsllSpartanburg, SC · Nov 2, 2009#59
Originally Posted by Tamago ↑
do the suspension first, and then worry about wheels/tires after.

remember, the tire itself is the most important mod. size is less of an issue, whereas the tire compound itself is VERY important. don't go cheap on tires, and it'll reward you.
there is much truth in this statement... if i could only do one mod to the car, id buy star spec direzza's for it.
CtrlAltDefeatIndianapolis IN · Nov 2, 2009#60
Originally Posted by kngrsll ↑
there is much truth in this statement... if i could only do one mod to the car, id buy star spec direzza's for it.
it's funny you mention those.. I'm thinking about upgrading my stock wheels to 17x7 Enkei RPF1 wheels with 215/40 star spec direzza's... I plan on keeping my stock steelies for winter use. The RPF1wheels are about the same weight as the the stock 15s, so I don't think weight will be an issue. This is my daily driver, so I am wondering if I'm going dangerously low profile and whether or not the ride will be too rough... Any one got any advice? Tamago? 🙌
TamagoThread starterOff Grid · Nov 2, 2009#61
sidewall is less important than the tire you choose. a 55 sidewall StarSpec is gonna be better than a 40sidewall (17inch) somethingelse..

sidewall is only detrimental when you're working with crappy tires like the Falken 512. the sidewalls are soft, and flex way too much in cornering loads.
JumpmanYarisSO. INDIANA · Nov 2, 2009#62
Tamago u need to work on my vehicle make it like urs
kngrsllSpartanburg, SC · Nov 2, 2009#63
Originally Posted by CtrlAltDefeat ↑
it's funny you mention those.. I'm thinking about upgrading my stock wheels to 17x7 Enkei RPF1 wheels with 215/40 star spec direzza's... I plan on keeping my stock steelies for winter use. The RPF1wheels are about the same weight as the the stock 15s, so I don't think weight will be an issue. This is my daily driver, so I am wondering if I'm going dangerously low profile and whether or not the ride will be too rough... Any one got any advice? Tamago? 🙌
that set up sounds fine to me. i prefer smaller tires mostly bc they are cheaper and i see alot of fast people use that set up. im not an engineer, so i just copy what works. im using 15x7's with a 195/55/15 dunlop. its a great set up. you can get the wheels for $120 a piece or less, and the tires are like $80 a piece. awesome deal, awesome set up... ive passed corvettes on hoosiers with this set up lol, seriously. cant wait to get the LSD installed and get some real race tires to try out nasa TT!
CtrlAltDefeatIndianapolis IN · Nov 2, 2009#64
Originally Posted by kngrsll ↑
that set up sounds fine to me. i prefer smaller tires mostly bc they are cheaper and i see alot of fast people use that set up. im not an engineer, so i just copy what works. im using 15x7's with a 195/55/15 dunlop. its a great set up. you can get the wheels for $120 a piece or less, and the tires are like $80 a piece. awesome deal, awesome set up... ive passed corvettes on hoosiers with this set up lol, seriously. cant wait to get the LSD installed and get some real race tires to try out nasa TT!
the derezza star specs were on sale iguess becausethey were $111 a piece for the 17" wheels
TamagoThread starterOff Grid · Nov 2, 2009#65
Originally Posted by JumpmanYaris ↑
Tamago u need to work on my vehicle make it like urs
like the xA, not like the MR2 haha the MR2 is awful right now! Drift City!
fmicleSan Jose, CA, USA · Nov 2, 2009#66
Originally Posted by kngrsll ↑
that set up sounds fine to me. i prefer smaller tires mostly bc they are cheaper and i see alot of fast people use that set up. im not an engineer, so i just copy what works. im using 15x7's with a 195/55/15 dunlop. its a great set up. you can get the wheels for $120 a piece or less, and the tires are like $80 a piece. awesome deal, awesome set up... ive passed corvettes on hoosiers with this set up lol, seriously. cant wait to get the LSD installed and get some real race tires to try out nasa TT!
I was actually looking at some rims today and saw that if I went with 15x7" I'd have more to choose from as opposed to 15x6.5", as recommended by this thread. I want to go as light as I can for a reasonable price on the wheels. Maybe Enkei or something.

So how much can I deviate from "the letter of the law"? 😉 Are there any trade-offs? Most tires seem to fit a range (such as 5"-7" for instance), so that wouldn't affect the tire selection much. What would I sacrifice/risk with a 15x7 setup?
TamagoThread starterOff Grid · Nov 2, 2009#67
Originally Posted by fmicle ↑
What would I sacrifice/risk with a 15x7 setup?
nothing if the weight was on point :)
advocatelocation · Nov 4, 2009#68
Tamago could you offer your opinion on these wheels:

http://www.good-win-racing.com/Mazda...t/21-1045.html

Things I need help choosing:
Tire sizes: for street use. going for good mix between weight / traction. have 205s now would like to go smaller.
Wheel size: 14s vs 15s. i want a good mix between weight / looks. i'm thinking 14s just might be too small since the car is not a miata after all.
Wheel width: 15x7? 15x7.5?

Relevant info:
Running the DF210s and Tokico blues.

If I had to take a stab in the dark i'd probably go with 15x7.5 with 195/50/15.
Any thoughts? More importantly is that Miata wheel even going to fit? I picked them because they're cheaper than hell, amazingly light, and from konig. Figured it was a great combo.
Thanks!
🙇
TamagoThread starterOff Grid · Nov 4, 2009#69
Originally Posted by advocate ↑
Tamago could you offer your opinion on these wheels:

http://www.good-win-racing.com/Mazda...t/21-1045.html

Things I need help choosing:
Tire sizes: for street use. going for good mix between weight / traction. have 205s now would like to go smaller.
Wheel size: 14s vs 15s. i want a good mix between weight / looks. i'm thinking 14s just might be too small since the car is not a miata after all.
Wheel width: 15x7? 15x7.5?

Relevant info:
Running the DF210s and Tokico blues.

If I had to take a stab in the dark i'd probably go with 15x7.5 with 195/50/15.
Any thoughts? More importantly is that Miata wheel even going to fit? I picked them because they're cheaper than hell, amazingly light, and from konig. Figured it was a great combo.
Thanks!
🙇
if you're going for looks, avoid 6.5" wide wheels. they simply don't fill the fenders very well. if you're looking to save weight, the wheel above is the one for you, very lightweight for the money, but you're sacrificing (IMO of course) looks FOR weight, i think that wheel looks awful 😲 hehe.
kngrsllSpartanburg, SC · Nov 4, 2009#70
Originally Posted by fmicle ↑
I was actually looking at some rims today and saw that if I went with 15x7" I'd have more to choose from as opposed to 15x6.5", as recommended by this thread. I want to go as light as I can for a reasonable price on the wheels. Maybe Enkei or something.

So how much can I deviate from "the letter of the law"? 😉 Are there any trade-offs? Most tires seem to fit a range (such as 5"-7" for instance), so that wouldn't affect the tire selection much. What would I sacrifice/risk with a 15x7 setup?
i use a 15x7 and it works great, i would use anywhere from a 195-225 on it and it will be fine. you wouldnt be sacrificing anything but a tiny bit of weight.
kngrsllSpartanburg, SC · Nov 4, 2009#71
Originally Posted by CtrlAltDefeat ↑
the derezza star specs were on sale iguess becausethey were $111 a piece for the 17" wheels
another reason i like 15" tires, they are MUCH cheaper.
kngrsllSpartanburg, SC · Nov 4, 2009#72
Originally Posted by advocate ↑
Tamago could you offer your opinion on these wheels:

http://www.good-win-racing.com/Mazda...t/21-1045.html

Things I need help choosing:
Tire sizes: for street use. going for good mix between weight / traction. have 205s now would like to go smaller.
Wheel size: 14s vs 15s. i want a good mix between weight / looks. i'm thinking 14s just might be too small since the car is not a miata after all.
Wheel width: 15x7? 15x7.5?

Relevant info:
Running the DF210s and Tokico blues.

If I had to take a stab in the dark i'd probably go with 15x7.5 with 195/50/15.
Any thoughts? More importantly is that Miata wheel even going to fit? I picked them because they're cheaper than hell, amazingly light, and from konig. Figured it was a great combo.
Thanks!
🙇
i use a spec miata wheel right now (Team Dynamics) and it is a perfect fit as if it were made for the car.
advocatelocation · Nov 4, 2009#73
Need some pics kngrsll! Also, thx for the confirmation
kngrsllSpartanburg, SC · Nov 4, 2009#74
Originally Posted by advocate ↑
Need some pics kngrsll! Also, thx for the confirmation
ive posted some before...

New wheels
ROCKLAND TOYOTAROCKLAND COUNTY NY · Nov 30, 2009#75
TAMAGO,
on a 205-55-15 setup what tire pressure should be ran for commuting at speeds between 70-90 on a daily basis? current pressure is 36 lbs......
TamagoThread starterOff Grid · Nov 30, 2009#76
Originally Posted by ROCKLAND TOYOTA ↑
TAMAGO,
on a 205-55-15 setup what tire pressure should be ran for commuting at speeds between 70-90 on a daily basis? current pressure is 36 lbs......
sounds good.

if you want better fuel economy at the risk of wearing the center of your tires out prematurely, go up a few psi.

if you want better grip, drop a few psi off.

i run 36 front, 28 rear on my xA, but i also don't have a standard alignment or weight bias.
ddongbaphay · Dec 4, 2009#77
I remember running my Re92s at 52~ psi. They started splitting down the middle. Cool stuff.
allyartJakarta, Indonesia · Apr 29, 2012#78
i have a yaris 5doors hatchback, may i ask some question:

1. when tamago says yaris is he refer to the yaris sedan or the yaris hatchback?

2. when tamago explain the rear swaybar, does he means something like ultra racing Rear Anti-roll Bar / Rear Sway Bar / Rear Stabilizer Bar (Code : UR-AR23-197) OR the ultra racing Rear Anti-roll Bar / Rear Sway Bar / Rear Stabilizer Bar (Code : UR-AR16-126)?

3. lastly, how do you feel about ultra racing Front Strut Bar / Front Tower Bar (Code : UR-TW2-402). is it a good investment to buy?

many thanks for the reply, sorry for my bad english
eTiMaGoBangkok, Thailand · Apr 30, 2012#79
wow hadn't read this thread in a while :)

1) I think this would apply to both, but I'm quite sure he meant the hatchback

2) At the time of writing there was really only the TRD rear swaybar. UR offers swaybars now in two thicknesses, The thicker one will have a stronger effect and induce more oversteer.

3) front strut bars are a bit of a controversial topic. Some say that because the shock tower are more or less directly connected to the firewall, there's no point in adding a bar. But some say that at higher cornering speeds (i.e. on track or autocross), you can feel a difference.

So in the end, I think it depends if you plan to seriously race the car or not? If it's to enjoy a spirited drive, you should be fine with the smaller swaybar and no strut bar, as you'd probably never push the car to the limits of handling on a public road (at least I hope not)
allyartJakarta, Indonesia · Apr 30, 2012#80
Originally Posted by eTiMaGo ↑
wow hadn't read this thread in a while :)

1) I think this would apply to both, but I'm quite sure he meant the hatchback

2) At the time of writing there was really only the TRD rear swaybar. UR offers swaybars now in two thicknesses, The thicker one will have a stronger effect and induce more oversteer.

3) front strut bars are a bit of a controversial topic. Some say that because the shock tower are more or less directly connected to the firewall, there's no point in adding a bar. But some say that at higher cornering speeds (i.e. on track or autocross), you can feel a difference.

So in the end, I think it depends if you plan to seriously race the car or not? If it's to enjoy a spirited drive, you should be fine with the smaller swaybar and no strut bar, as you'd probably never push the car to the limits of handling on a public road (at least I hope not)
ahh i got it, thanks for the explanation

for now i just want to enjoy a spirited drive, so i will just buy the smaller swaybar. but i have to say, having a strutbar is kinda cool though 🎉
eTiMaGoBangkok, Thailand · Apr 30, 2012#81
Yeah it does look nice under the hood :p But due to the rather small engine bay, it makes access to the battery and other stuff at the back a bit difficult, just so you know.
tooterLos Angeles · Apr 30, 2012#82
Originally Posted by kngrsll ↑
i use a spec miata wheel right now (Team Dynamics) and it is a perfect fit as if it were made for the car.
Even this two year old thread still has useful information. I also ordered wheels (Rota RB's) to Mazda Miata specifications, and they'll be arriving any day now. 🙂

My thanks to the good folk who left these messages of good advice.👍
ViperoniBrampton, ON · Apr 30, 2012#83
Originally Posted by eTiMaGo ↑

3) front strut bars are a bit of a controversial topic. Some say that because the shock tower are more or less directly connected to the firewall, there's no point in adding a bar. But some say that at higher cornering speeds (i.e. on track or autocross), you can feel a difference.
In my echo, and on my old slicks, in bumpy corners, I absolutely felt a difference with the strut bar. The front end gripped while the rear didn't, I had oversteer in a couple corners while I was getting used to it, almost got in trouble.
TamagoThread starterOff Grid · Jun 21, 2012#84
Originally Posted by Viperoni ↑
In my echo, and on my old slicks, in bumpy corners, I absolutely felt a difference with the strut bar. The front end gripped while the rear didn't, I had oversteer in a couple corners while I was getting used to it, almost got in trouble.
what were your tire pressures? (this has a lot more to do with your issue than any suspension component, especially on R comps)
Autocross72Seattle · Dec 28, 2012#85
Not only does a front strut bar make a difference, there is a difference between strut bars. My first strut bar was a Tanabe. I installed it and adjusted the preload. As I did so, I discovered that I could easily deform the bar by pushing on it. If my scrawny self can bend it, just think what a 2,200 pound car can do. When I drove the car with the Tanabe, I wanted to believe that there was a difference in turn in because of the money I spent on it, but ultimately I could not really tell a difference between the Tanabe installed and no bar installed. Eventually, I bit the bullet and ordered an Ultra Racing front bar. That, I can tell you, made a very noticeable difference! Turn in was much more crisp. Of course, this is all relative to my set up, so here are my details; Megan racing coil-overs and adjustable shocks, 23mm Ultra Racing rear sway bar, front and rear under braces, and 16.3 lb, 17x7.5" Motegi MR125 wheels with Toyo Proxes 4 205/40 tires. The main reason I chose that tire and wheel combo is that it keeps my speedo correct. This is my daily driver. I have a 1972 240Z for autocrossing and track days, but if I ever decide to Autocross my Yaris (I did once), I will definitely buy some 15x7" wheels with 205/50 or 225/50 Kumho V710s. The underpowered Yaris needs all the help it can get from the lower gearing of the smaller wheels.

By the way, has anyone ever tried an off set tire set up? I'm thinking of 225/50/15 in front and 205/50/15 in the rear. With that set up you might not need as much front camber which would give you better acceleration and braking (camber reduces the contact patch when the car is going straight).
TamagoThread starterOff Grid · Jun 28, 2013#86
Originally Posted by arnoldod ↑
Thanks for this great guide! :)

I had problem with handling in my first 4000 miles but now the handling has changed drastically. I do not do autocross. My driving characteristic is spirited driving, but only in the weekend. I am stuck in the traffic for the rest of the week with 19 Mph average speed.

I am using Toyo Proxes R1R 195/55/R15 with Advanti Storm-1 wheels (10.9 lbs). I understand that the tires won't last to 20,000 miles but my mileage is short (40 miles weekdays, 28 miles weekend).

The air pressure for both front and rear is 35. What is the recommended air pressure for my tires?
if you are commuting, and experience little rain, you could up that pressure for better fuel economy (provided the roads are dry). if it rains, keep the pressures at or slightly below the recommended pressure. remember too, your vehicle weight distribution. there's no reason to run the same pressures front and rear (if you don't carry many passengers, or heavy loads in the rear of your car) as your weight distribution f/r is at least 15/20 percent in the rear "less". less tire pressure in the rear will prevent oversteer, but also may induce understeer on sweeping turns.

as you aren't actually racing the car, all of the above is just theory. enjoy the yaris, and i'm sure tire pressures won't really be a factor. there's really no reason to ever push your car past 70% capability on the street, legally.
cali yarisCanoga Park, CA · Jun 28, 2013#87
^ Whoa. Welcome back. 🙂
tk-421Dagobah · Jun 28, 2013#88
Yeah, no kidding. 👍
arminiusAlberta · Aug 19, 2013#89
Hello,

A noob question for Tamago or suspension experts, I purchased a 2004 Echo that was kept by the original owner in his garage and only had 49,000 miles. The car was certified by Toyota and the engine bay is mint and looked new.

I already purchased a Tanabe NF210, and is looking to upgrade the shocks and struts to Koni Yellow or KYB GR2s.

The question is: Will a 15x7 offset of +25 XXR 527 or 522 work for the car without any issues, using 175/50/15 Yokohama S Drives?

Tamago has mentioned using 15x6.5 offset of +38 for street use is fine.

Thanks in advance.
arminiusAlberta · Aug 19, 2013#90
Sorry, wrong tire specs.

Should be:

195/50/15 Yokohama S Drive
hondajtUnited States · Nov 25, 2014#91
Since it's a sticky, I don't feel bad reviving this old thread.

My '13 Yaris is really twitchy on the highway. My wife's '09 is very smooth by comparison. We both have stock suspension and tires. I'm hoping someone will have some advice. From what I've read in this thread, I'm hoping it's a simple toe or camber adjustment.
LTHatchNewark NJ · Nov 25, 2014#92
Hondajt: I had the exact same issue, the Yaris felt unstable at highway speeds, felt nervous. 205mm wide tires and lowering springs knocked that down a good bit, but driving time is what fixed it for me. The more time i spent driving it the less noticeable it became, now i don't notice any twitchy behavior at all.
Rear sway bar also seems to be a well praised mod that knocks down the nervous feeling the Yaris has at highway speeds, it might be worth a look into if you want to leave the Yaris mostly stock.
CoryMWhite Rock BC · Nov 25, 2014#93
Originally Posted by hondajt ↑
Since it's a sticky, I don't feel bad reviving this old thread.

My '13 Yaris is really twitchy on the highway. My wife's '09 is very smooth by comparison. We both have stock suspension and tires. I'm hoping someone will have some advice. From what I've read in this thread, I'm hoping it's a simple toe or camber adjustment.
Incorrect toe, camber and caster can all make the car wander, or feel twitchy. Keep in mind, they are two different cars. Different track width, tire size etc can create different feels.

Cheers.
TapokataSacramento, CA · May 18, 2016#94
So, after nearly 160K miles, I'm getting ready to replace the rear shocks on my 09 liftback- changing out the OEM units for a a pair of Bilstein B6's. I plan to replace the bushings, bumpers, and supports with new OEM bits, and retain the other hardware. At the same time, I'm intend to add a TRD torsion spring / sway bar. I'm also going to add a Universal Racing two-point rear strut bar. The suspension is otherwise stock (I'll have the front struts changed out- they're still factory OEM- at a future date). I upsized the wheels and tires from the 14" base to a 15", running P185/60R15's on them, last year. Except for the back end being a bit light, especially on the freeway in high winds (or being buffeted by semi's), it handles pretty well- I like throwing this little washing machine on wheels around our fair city streets.

Lots of experts on this forum- so I'll ask: anything that I need to watch out for or otherwise be aware of in this re-fit? The shock replacement looks to be pretty straightforward, as is the installation of the sway bar and strut. Just checking one more time to see if there are any known (or unknown) gremlins to watch out for in this process. Thanks in advance...
CrankyOldManWest Michigan · May 18, 2016#95
Originally Posted by Tapokata ↑
Lots of experts on this forum- so I'll ask: anything that I need to watch out for or otherwise be aware of in this re-fit? The shock replacement looks to be pretty straightforward, as is the installation of the sway bar and strut. Just checking one more time to see if there are any known (or unknown) gremlins to watch out for in this process. Thanks in advance...
Dropping the large washer between the wheel well and the plastic interior trim. You will lose your mind trying to get it back out. Same goes for the jam nuts.

I recommend getting it up on a lift if you can, makes the whole process so much simpler than putting it on jacks. I would also suggest buying extra bolts--I've had a few of the lower bolts shear off when changing them.
DarkShadowFoxMassachusetts · Sep 23, 2017#96
Originally Posted by CrankyOldMan ↑
Dropping the large washer between the wheel well and the plastic interior trim. You will lose your mind trying to get it back out. Same goes for the jam nuts.

I recommend getting it up on a lift if you can, makes the whole process so much simpler than putting it on jacks. I would also suggest buying extra bolts--I've had a few of the lower bolts shear off when changing them.
if you just put all your nuts and bolts into a bag and label/tape them together you will be a okay.

Sent from my LG-H918 using Tapatalk
CalrenmanSo. Cal. Ventura · Apr 4, 2022#97
Great thread! Worth reading.
HausapesEsoty · Feb 18, 2024#98
Is there any specific advice or tips you would share regarding the re-fit process and potential challenges mentioned by CrankyOldMan and DarkShadowFox, especially concerning the large washer and jam nuts?
TamagoThread starterOff Grid · Jan 25, 2026#99
crazy to come back after all this time to see this thread still stickied!