Yarisworld Archive

How do I cure a lean condition?

100 posts · 31,501 views · page 2 of 2

Replies continued

LtNoogieThread starterWest Hills, CA · Mar 16, 2009#51
Originally Posted by camelll ↑
My sensor is right after the manifold pre cats and under wot I get between 11 and 12. I would think after the cat or cats his readings are okay.🤷
Does that mean that the first cat is oxidizing, or whatever a cat does, the exhaust mixture to lower the amount of unburnt fuel thereby raising the a/f mixture?
largeorangefontSo Cal, OC · Mar 16, 2009#52
Originally Posted by LtNoogie ↑
Does that mean that the first cat is oxidizing, or whatever a cat does, the exhaust mixture to lower the amount of unburnt fuel thereby raising the a/f mixture?
Yes, but the cat does the same thing all the time. Your AFR is accurate while cruising. We have to assume it is close to accurate under boost conditions.
LtNoogieThread starterWest Hills, CA · Mar 16, 2009#53
Ok. I was planning to run the SpeedVentures Streets of Willow on April 10 where I expect prolonged WOT operation and lots of boosting. Based on what you're telling me, that may not be a good idea until I get the AFR under control, right?
largeorangefontSo Cal, OC · Mar 16, 2009#54
Originally Posted by LtNoogie ↑
Ok. I was planning to run the SpeedVentures Streets of Willow on April 10 where I expect prolonged WOT operation and lots of boosting. Based on what you're telling me, that may not be a good idea until I get the AFR under control, right?
No, I believe you will be ok. What I would do is get or borrow a fancy scangauge and monitor your timing. Compare it with a stock car and see if there is a difference. Then you will know what the black box is doing. If your timing is lower, you should be just fine.

I may be going to the April 10th day as well.
LtNoogieThread starterWest Hills, CA · Mar 16, 2009#55
I have a scangauge. Perhaps I'll make another video and strap the scangauge on top of the other gauges so that we can see how timing corresponds to AFR and boost levels.

What other scangauge settings would be useful to view? I have RPM currently showing also. I can ditch the two MPG settings for this video.
LtNoogieThread starterWest Hills, CA · Mar 16, 2009#56
Originally Posted by camelll ↑
Long I would be curious what your readings would be if you moved the sensor to pre cat position? I would try that before buying a piggyback.
Mike, I would rather poke out my eyes than to try to get that bung moved and the cable moved with it. Getting everything in place once was damn difficult.
largeorangefontSo Cal, OC · Mar 16, 2009#57
Originally Posted by LtNoogie ↑
I have a scangauge. Perhaps I'll make another video and strap the scangauge on top of the other gauges so that we can see how timing corresponds to AFR and boost levels.

What other scangauge settings would be useful to view? I have RPM currently showing also. I can ditch the two MPG settings for this video.
That is great!

RPM, ignition advance, injector duty or latency, and if there is a load, or airflow parameter, that would be perfect.

Or if you want to post a list of everything it can do I can tell you which ones you will want to monitor.

You have an auto right?
LtNoogieThread starterWest Hills, CA · Mar 16, 2009#58
Originally Posted by largeorangefont ↑
That is great!

RPM, ignition advance, injector duty or latency, and if there is a load, or airflow parameter, that would be perfect.

Or if you want to post a list of everything it can do I can tell you which ones you will want to monitor.

You have an auto right?
Ok, I'll make a list tonight of the values it can display.

I know it can do RPM, ignition advance, and load. I don't think the other settings produce a value. Perhaps the ECU does not report them to the scangauge.
largeorangefontSo Cal, OC · Mar 16, 2009#59
* Engine Speed (RPM)
* Manifold Pressure (not available on some vehicles)
* Engine Load
* Ignition Timing

If Manifold Pressure is not available, use Throttle Position instead.
largeorangefontSo Cal, OC · Mar 16, 2009#60
Originally Posted by LtNoogie ↑
Ok, I'll make a list tonight of the values it can display.

I know it can do RPM, ignition advance, and load. I don't think the other settings produce a value. Perhaps the ECU does not report them to the scangauge.

The ECU does report them, but the Scangauge probably does something to the value to get the fuel economy/fuel rate numbers.

What unit does the fuel rate parameter use?
LtNoogieThread starterWest Hills, CA · Mar 16, 2009#61
cpm... I think. I've never known what to do with that reading.
LtNoogieThread starterWest Hills, CA · Mar 16, 2009#62
Originally Posted by largeorangefont ↑
* Engine Speed (RPM)
* Manifold Pressure (not available on some vehicles)
* Engine Load
* Ignition Timing

If Manifold Pressure is not available, use Throttle Position instead.
Wouldn't you get Manifold Pressure from my boost gauge or is that a different manifold pressure?
LtNoogieThread starterWest Hills, CA · Mar 16, 2009#63
Originally Posted by camelll ↑
I have a tach, boost/vacuum gauge and I already monitor the timing and load. How does the throttle position fit in or correlate with the others?
You just don't have a video camera!😁
LtNoogieThread starterWest Hills, CA · Mar 16, 2009#64
I just use my cheap Olympus digital camera and run it in movie mode. Most all of the cameras have that mode.
KCALB SIRAYVirginia · Mar 16, 2009#65
I hear WalMart has a good deal on Hanna Montana designed vid cameras, lol.
KCALB SIRAYVirginia · Mar 16, 2009#66
lol
largeorangefontSo Cal, OC · Mar 16, 2009#67
Originally Posted by camelll ↑
I have a tach, boost/vacuum gauge and I already monitor the timing and load. How does the throttle position fit in or correlate with the others?

It is the same, but it was hard to see in the video.
LtNoogieThread starterWest Hills, CA · Mar 16, 2009#68
I'll try to do a better job next time. Thanks.
largeorangefontSo Cal, OC · Mar 16, 2009#69
Originally Posted by camelll ↑
Where did largeorangefont go? I would like him to explain some of this shiiiiit to me cause I really don't know. I understand about timing, advancing or retarding and when I am under boost the load is basically on 99 percent. I just don't understand how all of these tie together with rpm and manifold pressure.
Sorry, Had to do some actual work. I gotta head out to a customer, so here is a brief overview.

In reality \keeping an engine alive comes down to EGT (exhaust gas temperature) and knock.

You use a balance of AFR and timing to keep both factors in check. You can't crank up both and expect an engine to live.

Think of fuel as coolant for the combustion chamber. Think of ignition advance as how hot the fire burns. Obviously if the fire burns too hot, bad things happen. If it burns too cool, the car runs like crap and is slow. The temperature of that fire is EGT. You can control EGT by adding more coolant (fuel) or turning down the intensity of the flame (ignition retard).

OEM supercharged cars will (generally!!) run low timing and a high AFR to increase fuel economy and reduce emissions. My Cobra for example ran in the high 13 AFR range under load, but only had 10 degrees of ignition advance from the factory.

I now run the AFR and 11.3:1 AFR under load, and 21 degrees of ignition advance, and picked up 30 some odd HP and torque. It runs like a different car. The increased timing makes the car more responsive on tip in (passing etc.), and much more driveable. Power "under the curve" is increased as well as peak power.

EGTs in both scenarios were VERY similar, at around 1300F. From this example, you can see there are many ways to the same end. Some produce more power than others.

Knock is another factor to be wary of. Again, to get rid of knock you can add more fuel, or retard timing. Strategies can vary on how to get rid of knock, especially in turbo applications.
largeorangefontSo Cal, OC · Mar 16, 2009#70
Originally Posted by LtNoogie ↑
I'll try to do a better job next time. Thanks.

No problem, you just have a like a 30 # boost gauge 🎉
eTiMaGoBangkok, Thailand · Mar 16, 2009#71
Originally Posted by largeorangefont ↑
Sorry, Had to do some actual work. I gotta head out to a customer, so here is a brief overview.

In reality \keeping an engine alive comes down to EGT (exhaust gas temperature) and knock.

You use a balance of AFR and timing to keep both factors in check. You can't crank up both and expect an engine to live.

Think of fuel as coolant for the combustion chamber. Think of ignition advance as how hot the fire burns. Obviously if the fire burns too hot, bad things happen. If it burns too cool, the car runs like crap and is slow. The temperature of that fire is EGT. You can control EGT by adding more coolant (fuel) or turning down the intensity of the flame (ignition retard).

OEM supercharged cars will (generally!!) run low timing and a high AFR to increase fuel economy and reduce emissions. My Cobra for example ran in the high 13 AFR range under load, but only had 10 degrees of ignition advance from the factory.

I now run the AFR and 11.3:1 AFR under load, and 21 degrees of ignition advance, and picked up 30 some odd HP and torque. It runs like a different car. The increased timing makes the car more responsive on tip in (passing etc.), and much more driveable. Power "under the curve" is increased as well as peak power.

EGTs in both scenarios were VERY similar, at around 1300F. From this example, you can see there are many ways to the same end. Some produce more power than others.

Knock is another factor to be wary of. Again, to get rid of knock you can add more fuel, or retard timing. Strategies can vary on how to get rid of knock, especially in turbo applications.
A very delicate balancing act 🙂
whooppee777Maryland · Mar 16, 2009#72
so if we got the cam com we could adjust the cams to cope with the crazy a/f readings?
largeorangefontSo Cal, OC · Mar 16, 2009#73
Originally Posted by whooppee777 ↑
so if we got the cam com we could adjust the cams to cope with the crazy a/f readings?
No, the cam has nothing to do with it.
kurokoma-kunmy own little world · Mar 16, 2009#74
Originally Posted by largeorangefont ↑
You can control EGT by adding more coolant (fuel) or turning down the intensity of the flame (ignition retard).
Crap, I have got to get off my a$$ and install my gauges! Without knowing the AFR, seems like knowing the ignition timing means nothing 😕

Currently I just gave a tach and scangauage on volt, ign, tps, and cycle through others (load, loop, temps). I have boost/vac and wideband a/f and oil press. still in their boxes 🆘

Cruising around at 2500-3500 rpm, the tps is ~25, load is say 50, ign timing is usually ~30. Under boost (load 99 and tps 25+) it quickly drops to half that... is that normal?
LtNoogieThread starterWest Hills, CA · Mar 16, 2009#75
Originally Posted by kurokoma-kun ↑
Crap, I have got to get off my a$$ and install my gauges! Without knowing the AFR, seems like knowing the ignition timing means nothing 😕

Currently I just gave a tach and scangauage on volt, ign, tps, and cycle through others (load, loop, temps). I have boost/vac and wideband a/f and oil press. still in their boxes 🆘
I cannot fault you for being slow. I started the thread about gauges for boosted applications at the end of October. It's now mid-March and I just got two of my three gauges working (boost/vac & wideband a/f). Oil pressure should be done next weekend...maybe.

As for the scangauge, I normally set it to trip MPG, instant MPG, RPM, & fWt
largeorangefontSo Cal, OC · Mar 16, 2009#76
Originally Posted by kurokoma-kun ↑
Crap, I have got to get off my a$$ and install my gauges! Without knowing the AFR, seems like knowing the ignition timing means nothing 😕

Currently I just gave a tach and scangauage on volt, ign, tps, and cycle through others (load, loop, temps). I have boost/vac and wideband a/f and oil press. still in their boxes 🆘

Cruising around at 2500-3500 rpm, the tps is ~25, load is say 50, ign timing is usually ~30. Under boost (load 99 and tps 25+) it quickly drops to half that... is that normal?
Yes that sounds correct.
kurokoma-kunmy own little world · Mar 16, 2009#77
Originally Posted by LtNoogie ↑
I cannot fault you for being slow.
thanks... this whole project has taken me forever though. I'm a terribly slow weekend mechanic and even slower electrician, plus it's taken me a long time to get a mental grip on the basics of boost--had a lot to learn and still do, but experience is the best teacher I guess 😁


Originally Posted by largeorangefont ↑
Yes that sounds correct.
thank you for the reassurance 🙂
kurokoma-kunmy own little world · Mar 16, 2009#78
Originally Posted by camelll ↑
These are pretty much the numbers I see as well jo.
Interesting! now I'm very curious to know what Long and others are getting, and how to interpret it all.
LtNoogieThread starterWest Hills, CA · Mar 16, 2009#79
I was seeing ign timing dropping to single digits under boost this evening.
rpalaiFlorida, USA · Mar 17, 2009#80
I have to agree with the comments posted by most of the members. Slightly larger injectors, or is there any way of possibly increasing fuel pressure to the injectors under boost to a higher level than the controller is allowing? Perhaps an Apexi-II unit or something similar that can work alongside the Blitz fuel controller? This lean condition is a real concern and has to be fixed! If it is happening in your car, it most likely is happening to everyone who has this system installed, like me! This will probably be an interesting and do-able fix, hopefully. Thanks! RPALAI
cali yarisCanoga Park, CA · Mar 17, 2009#81
would be pretty easy to throw a set of Scion tC injectors (about a hundred bucks on eBay) and see what happens.
largeorangefontSo Cal, OC · Mar 17, 2009#82
Originally Posted by LtNoogie ↑
I was seeing ign timing dropping to single digits under boost this evening.
Yea, the car is fine then... Don't loose any sleep over it.
largeorangefontSo Cal, OC · Mar 17, 2009#83
Originally Posted by cali yaris ↑
would be pretty easy to throw a set of Scion tC injectors (about a hundred bucks on eBay) and see what happens.
That would be the worst thing he could do at this point. If he is seeing single digits for timing under load, he does not want to add more fuel.
largeorangefontSo Cal, OC · Mar 17, 2009#84
Originally Posted by camelll ↑
I am not seeing a lean condition, my wideband show's between 11 and 12 under wot and stoich at idle. my scangauge readings are on par with korokuma kun's. I was however experiencing pre ignition but that has been stopped with the lucas octane booster and 93 octane in the tank. Noogie however was seeing a lean condition when his car was on the dyno and is showing a condition now but does not have the sensor in the optimal spot.🤷

I am gonna have to mess with the camera and check out its video settings or just break down and by a camcorder.
I could not tell you why the 2 of you are seeing differences. Is your black box hooked up properly? Noogie is stting stoich at idle and during cruise as well, so again, his wideband is close to accurate.

Noogie is seeing low timing, so I am assuming that the black box is offsetting timing under load. What kind of timing values do you see under boost?
kurokoma-kunmy own little world · Mar 17, 2009#85
Originally Posted by LtNoogie ↑
I was seeing ign timing dropping to single digits under boost this evening.
Originally Posted by largeorangefont ↑
Yea, the car is fine then... Don't loose any sleep over it.
Lieutenant, your readings indicate a warp core breach is imminent... you've got to shut down the reactor now, then run a level 3 diagnostic on the matter/antimatter reaction control system 😲

sorry Long, not to make light of your concerns, I've just been wanting to say that to you for some time and now seemed like the right moment 😆 🙄
KCALB SIRAYVirginia · Mar 17, 2009#86
Originally Posted by LtNoogie ↑
I was seeing ign timing dropping to single digits under boost this evening.
Originally Posted by kurokoma-kun ↑
Lieutenant, your readings indicate a warp core breach is imminent... you've got to shut down the reactor now, then run a level 3 diagnostic on the matter/antimatter reaction control system 😲

sorry Long, not to make light of your concerns, I've just been wanting to say that to you for some time and now seemed like the right moment 😆 🙄
See Long, and you make fun of me when I speak Klingon😆
LtNoogieThread starterWest Hills, CA · Mar 17, 2009#87
I tried to make a video last night while driving and hand holding the camera. Not recommended. I'll install the camera mount tonight and shoot another video.
largeorangefontSo Cal, OC · Mar 17, 2009#88
Originally Posted by camelll ↑
I will say though that I have a different fuel controller than most, there are only 3 people that have the same fuel controller I do (that I am aware of). I was one of the first people to get this kit.
Well there you go. That probably explains some of the differences. If all of you were getting knock, they probably made some revisions to future kits.
PETERPOOPOahu · Mar 17, 2009#89
I'd like to chime in with my a/f readings, but I don't got a wideband a/f gauge yet. However, it is true that I have not experienced pre-ignition. But, I did put in lucas oil's octane booster with shell's 92 before i got the kit installed and running. I'm not sure if this is preventing the pre-ignition, but I am not experiencing any. I don't know if I don't use the boost octane if I will experience it or not, but I don't plan on not using the boost octane for a long time.

I'm also not experiencing the noise that occurs when the car is in idle and the a/c is on. I don't know if I have a lucky kit, or a newer kit, or what not, but my kit seems to run flawless as of now. We'll see if the story changes once I see my a/f readings.
LtNoogieThread starterWest Hills, CA · Mar 18, 2009#90
The video was too shaky to post.

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy
rpalaiFlorida, USA · Mar 18, 2009#91
Hello again all! Hope you are all doing well. Unfortunately, I am not! My car ran GREAT from the moment the Blitz system was installed as well as all last night and early this morning until the very last time I started it up, it threw a code and the check engine light came on. When I hook up my scanner, it shows the code as "pending" which probably is why it keeps doing it even after I clear the code with my scanner. Can someone help me with this? Whenever it throws the code, it goes into "limp mode" and becomes rather doggy of course. It is showing code P01387 which means that "voltage too high in 02 sensor 1 Bank 2", or something like that. Now I know that my mechanic told me that he had a problem getting the old 02 sensor out of the factory exhaust header to transfer it over to the new Meagan Racing header, but he WAS able to do it after he had to soak it in a LOT of PV Blaster penetrating oil for awhile. But that was now a couple of days ago and all of the PVBlaster should have burned off the 02 sensor by now, unless perhaps it destroyed it in the process? I can not figure this out. I am really bummed now becuase every time I start the car, it throws the same darned code and goes into limp mode again.

Can anyone please help me with this? Thanks!
Rich
rpalai
kurokoma-kunmy own little world · Mar 18, 2009#92
Here's what the repair manual has to say about P0138, O2 sensor high voltage:

"...when the air-fuel ratio is richer than the stoichiometric air-fuel level, the oxygen concentration in the exhaust gas becomes lean. The HO2 sensor informs the ECM that the post-TWC air-fuel ratio is rich (high voltage, i.e. more than 0.45 V). The HO2 sensor has the property of changing its output voltage drastically when the air-fuel ratio is close to the stoichiometric level."

So IMO he'll be wanting to pinpoint the cause of the extremely rich air-fuel ratio (injectors, fuel pressure, exhaust leak, etc.) in addition to checking the sensor itself.

You can find the entire Engine Control manual and many others here, hosted by our own etimago --> http://www.etimago.com/yaris/repairmanual/

PS-- you may get better response if you start your own thread for issues like this 🙂 it's too important to get buried among other info.
largeorangefontSo Cal, OC · Mar 18, 2009#93
Noogie,

What we need you do do is to do a WOT pull to redline from around 2000 RPM in 2nd.

Strap that camera down :)

Again, from the shots you provided I don't think you have anything to worry about.
whooppee777Maryland · Mar 18, 2009#94
Originally Posted by largeorangefont ↑
Again, from the shots you provided I don't think you have anything to worry about.
those are about the same readings i get.

if the lights on the gauge read 14ish and the lights around the edges are still in the green then ur mixture is good. right?
largeorangefontSo Cal, OC · Mar 18, 2009#95
Originally Posted by whooppee777 ↑
those are about the same readings i get.

if the lights on the gauge read 14ish and the lights around the edges are still in the green then ur mixture is good. right?
Not necessarily. If you timing is in the single digits, then yea it is probably OK. If not, those numbers are not OK.
PETERPOOPOahu · Apr 7, 2009#96
Originally Posted by largeorangefont ↑
Noogie,

What we need you do do is to do a WOT pull to redline from around 2000 RPM in 2nd.

Strap that camera down :)

Again, from the shots you provided I don't think you have anything to worry about.
Did you ever do this?
LtNoogieThread starterWest Hills, CA · Apr 7, 2009#97
No. I'm built a new camera mount but the digital camera died. I'm going to get some data logging software to collect data a little bit better than shaky videos.
Doc ZaiusOttawa, ON, Canada · Apr 7, 2009#98
For what it's worth, I've been watching my IGN on the SG. At idle, it typically is around 5, jumps to 10 every once in a while. When the defrost is on (and I guess A/C kicks in), the RPMs drop momentarily, and the IGN drops to -5 or -6... then back to +5.

Also when cruising and off-boost (TPS < 25), IGN is around 35. Drops to around 15-20 when boosting.
LtNoogieThread starterWest Hills, CA · Apr 7, 2009#99
But don't you get highest performance with more ignition advance? ... like around 20? Are we running in less than optimal mode? With the S/C turned off, my ignition is much more advanced.
cali yarisCanoga Park, CA · Mar 21, 2013#100