Yarisworld Archive

Installed the 1zz throttle body -

131 posts · 68,950 views · page 1 of 3

AlexNet0Original postRockland, ME · Jan 24, 2009#1
I installed the 1zz throttle body today, and after everything was bolted back up, the engine oscillated terribly, I was expecting the 2-3k revs, but then after a few minutes it started to rev weird, eventually dropping off and starting to rough idle between 500 and 2k rpm, I attempted to purge the air from the lines, and got a few bubbles out of the coolant, and no more were coming out, but it did the same thing. No CEL was present during this. 😠 🙄🙄🙄

So to prevent damage, I took it off and re-installed the stock throttle body, as I was doing this, I noticed that there was no coolant passing through the 1zz throttle body, the lines were empty. however when I bolted back up the stock TB and everything connected again, it oscillates between 2-3k rpm still, although I again purged the air from the coolant, getting more bubbles than I did with the 1zz TB.

What could this be from? I was shocked when I put the stock throttle body back on and it still oscillated like that. 😢

Replies 130

ddongbaphay · Jan 24, 2009#2
You gotta give it a while for the ECU to fix itself.

Right now, you're in limbo. The ECU thinks that it still has the 1zz TB in it, so its trying to fix the 1zz TB settings, when you're still rocking the stock one. Just stick to one for a little bit.

That coolant line just helps unfreeze the TB if you're in a region where stuff will freeze overnight. Doesn't really have anything to do with the idle.
AlexNet0Thread starterRockland, ME · Jan 24, 2009#3
You gotta give it a while for the ECU to fix itself.

Right now, you're in limbo. The ECU thinks that it still has the 1zz TB in it, so its trying to fix the 1zz TB settings, when you're still rocking the stock one. Just stick to one for a little bit.
I hope so, so what should I do, leave it overnight? should I disconnect the battery overnight?
ddongbaphay · Jan 24, 2009#4
Originally Posted by AlexNet0 ↑
I hope so, so what should I do, leave it overnight? should I disconnect the battery overnight?
I mean run your car with one TB. Just put up with the crappy idle for a day or so.
AlexNet0Thread starterRockland, ME · Jan 24, 2009#5
man, lol, thanks for the quick reply, so driving with it like that is the best solution?
I mean disconnecting the battery wont reset the ECU back to normal overnight?
thebarberGrand Rapids, MI · Jan 24, 2009#6
you use a gasket maker for the 1zz throttle body?

and you need to let the car idle for 10min or so w/ the new throttle body on it so the ecu can learn that its there...
AlexNet0Thread starterRockland, ME · Jan 24, 2009#7
no, I used the stock gasket, , but it felt like it sealed okay, perhaps not. anyway I will go sit in my car for like 10 minutes and see if the idle levels back out with the stock TB, thanks
ddongbaphay · Jan 24, 2009#8
Originally Posted by AlexNet0 ↑
man, lol, thanks for the quick reply, so driving with it like that is the best solution?
I mean disconnecting the battery wont reset the ECU back to normal overnight?
it might. But it would be better if the ECU figured it out.
ddongbaphay · Jan 24, 2009#9
Originally Posted by AlexNet0 ↑
no, I used the stock gasket, , but it felt like it sealed okay, perhaps not. anyway I will go sit in my car for like 10 minutes and see if the idle levels back out with the stock TB, thanks
Does the stock gasket seep into the 1zz TB? Or does it clear the bigger hole?
FunctionSpec626, Southern California · Jan 24, 2009#10
You need to get all the air out of the coolant. Its important that you do. Gently squeeze the lines and get the air bubbles moving out of the coolant. Gently rev it to get the coolant flowing. A large air bubble can cause an air-lock in the coolant that prevents the coolant from flowing through the throttle body and back into the coolant system.

Air bubbles cause the oscillations because of the difference in temperature. Air heats up faster then coolant so whenever an air bubble passes over the coolant temp sensor, it lowers the idle thinking the engine is warmed up and then when the colder coolant passes over, it raises the idle thinking the engine is still cold.

ECU doesn't need to "learn" anything. It adjusts accordingly to how much air is flowing in. You will always have a high idle on a cold startup with this setup because the ecu doesn't start measuring airflow 10secs after startup. Once it does start measuring, it'll adjust the idle.
AlexNet0Thread starterRockland, ME · Jan 24, 2009#11
I purged the air from the stock TB three times after re-installing it.

started up from cold, removed cap (not reservoir cap) and squeezed the coolant lines going to the TB until no more bubbles came up. Let the car cool down and did it again till there were no more bubbles.



should probably point out that I was tired of messing with it at that particular time as it was 13 degrees F and I was running out of daylight (no garage) just so people dont think Im a little b*tch lol
AlexNet0Thread starterRockland, ME · Jan 24, 2009#12
I just drove around for like a half hour and the revs dropped from 3k to 2k fully warmed up, Ill see how it is tomorrow
thebarberGrand Rapids, MI · Jan 24, 2009#13
Originally Posted by AlexNet0 ↑
no, I used the stock gasket, , but it felt like it sealed okay, perhaps not. anyway I will go sit in my car for like 10 minutes and see if the idle levels back out with the stock TB, thanks
you should use some gasket maker....the stock gasket isnt big enough for the new throttle body...

ddongbaphay · Jan 24, 2009#14
Originally Posted by FunctionSpec ↑
You need to get all the air out of the coolant. Its important that you do. Gently squeeze the lines and get the air bubbles moving out of the coolant. Gently rev it to get the coolant flowing. A large air bubble can cause an air-lock in the coolant that prevents the coolant from flowing through the throttle body and back into the coolant system.

Air bubbles cause the oscillations because of the difference in temperature. Air heats up faster then coolant so whenever an air bubble passes over the coolant temp sensor, it lowers the idle thinking the engine is warmed up and then when the colder coolant passes over, it raises the idle thinking the engine is still cold.

ECU doesn't need to "learn" anything. It adjusts accordingly to how much air is flowing in. You will always have a high idle on a cold startup with this setup because the ecu doesn't start measuring airflow 10secs after startup. Once it does start measuring, it'll adjust the idle.
Isn't that what learning is? Wouldn't that also explain why the stock TB is causing problems after he took the 1zz TB out?
YarisSedanCalifornia - Bay Area · Jan 24, 2009#15
Seeing its a larger throttle body. Say the computer needs to open the throttle 10 percent to let in a certain amount of air. With a larger throttle 10 percent is really like 25 percent. Which is why you will always have a high idle. But why you also get better throttle response and power. Because say you want to open the throttle to 50 percent normall its more like 75 percent if you compare the amount of air being sucked into the engine.

I would not attempt this mod till you have exhausted other possiblities of increasing power such as a AFE intake or trd exhause or headers. Before slapping on the throttle body.
AlexNet0Thread starterRockland, ME · Jan 24, 2009#16
solved the issue, I disconnected the battery for 5-10 minutes and when I connected it again..No more odd revs. Note that this is the stock TB that I was having issues with.


I would not attempt this mod till you have exhausted other possiblities of increasing power such as a AFE intake or trd exhause or headers. Before slapping on the throttle body.
I do not have money for exhaust or header, or I would have them already, I have a cold air that is working nicely for me now.

you should use some gasket maker....the stock gasket isnt big enough for the new throttle body...
how did you apply the gasket maker? To the Manifold side or the TB side?
ddongbaphay · Jan 24, 2009#17
Originally Posted by YarisSedan ↑
Seeing its a larger throttle body. Say the computer needs to open the throttle 10 percent to let in a certain amount of air. With a larger throttle 10 percent is really like 25 percent. Which is why you will always have a high idle. But why you also get better throttle response and power. Because say you want to open the throttle to 50 percent normall its more like 75 percent if you compare the amount of air being sucked into the engine.

I would not attempt this mod till you have exhausted other possiblities of increasing power such as a AFE intake or trd exhause or headers. Before slapping on the throttle body.
I think this TB would yield better results than an intake, and exhaust.
AlexNet0Thread starterRockland, ME · Jan 25, 2009#18
Ill try it again when its warmer out or I find someones garage to work in, its negative 7 right now.
thebarberGrand Rapids, MI · Jan 25, 2009#19
Originally Posted by AlexNet0 ↑
how did you apply the gasket maker? To the Manifold side or the TB side?
im pretty sure i put it on the throttle body

to be honest, i wouldnt being doing this in the cold....im not sure how the gasket maker will set up when its as cold as it is right now....

when i did mine it was in sept of 2008....so it wasnt too cold yet

but for the record you SHOULD be disconnecting the battery when you swap tb's....itll reset the ecu so the car can relearn on the new tb. let it idle for about 10min and then youre off. also, not a mod id keep on the car in winter due to the high idle when the engine is cold...
YarisPRMayaWest, Puerto Rico · Jan 25, 2009#20
Originally Posted by thebarber ↑
im pretty sure i put it on the throttle body

to be honest, i wouldnt being doing this in the cold....im not sure how the gasket maker will set up when its as cold as it is right now....

when i did mine it was in sept of 2008....so it wasnt too cold yet

but for the record you SHOULD be disconnecting the battery when you swap tb's....itll reset the ecu so the car can relearn on the new tb. let it idle for about 10min and then youre off. also, not a mod id keep on the car in winter due to the high idle when the engine is cold...

I still have 1zz and still oscilates, its and Iddle malfunction. I have installed the stock one a few times and you HAVE to disconect the batery and before the installation of any of the TB. And as thebarber said it take about 10 min for the car to iddle rigth after you put the 1zz TB.
saplaymateSATX · Jan 27, 2009#21
I explained to you in the PM how to clear the ECU instantly and apply the sealant; also you must adjust the throttle stop!
tk-421Dagobah · Jan 27, 2009#22
Originally Posted by saplaymate ↑
I explained to you in the PM how to clear the ECU instantly and apply the sealant; also you must adjust the throttle stop!
Could you post that info up here for those of us that are getting ready to do this mod? TIA
ztrack157Biggs, CA · Jan 27, 2009#23
I never knew about adjusting the throttle stop.
AlexNet0Thread starterRockland, ME · Jan 27, 2009#24
well, I guess I messed up and didnt pay attention with the ECU and the gasket, however I will try to explain what is involved to the best of my ability so far, will add pictures later on.

Remove whichever aftermarket intake you have installed, or remove the stock airbox by:
Unclasping the two clips holding the filter cover - use a flathead screwdriver to remove the round clamp holding the air tube to the box, and remove the tube from the throttle body opening. remove the MAF sensor plug from the top of the stock airbox. - Remove the top cover and air filter, and set aside to give you room to work.

Remove the TB-ECU plug from the right side of the Throttle Body, use a 10mm socket to remove the bracket that holds the wire bundle to the throttle body.
At this point if you havent already, remove the negative clamp from the battery and lay off to the side where it cannot touch either of the battery terminals.

(what I did-)Have a couple mid-size wire nuts handy, and remove the lower/front coolant line to the throttle body, and plug the line with the wire nut so no coolant leaks out.

Use the 10mm socket to remove the uppermost 2 bolts holding the large coolant return line. remove the next 2 bolts holding the bracket on to the throttle body and set the bracket aside.

Unclasp the second coolant line from the clip that was under the large coolant return line to free up slack to work with. use the other wire nut to plug the second coolant line for now.

Use the 10mm socket to remove the three remaining nuts and the one lower left bolt from the drivers-side facing side of the throttle body.

gently pull the throttle body toward the drivers side of the engine bay untill if comes free from the gasket (ensure you have the gasket in your hand after removing the TB, mine stuck to the Throttle Body and fell off before I realized it was there, lol)

--

Prepare the 1zz throttle body by removing any foreign dirt, grease, or whatever.
hold the throttle body Inlet facing you, ECU plug on your right, and you should see the throttle stop screw on the upper right-hand side, may or may not be covered by clear apoxy, regardless, you will need to remove the apoxy if it is present. You will need a small (not sure of size) allen wrench to adjust the idle.

(((((--------Let me know if I am not correct about this section--
Use the gasket maker as pointed out by thebarber on the previous page to make a consistant ring around the manifold side of the throttle body, let set for a few minutes, and place and slide the 1zz throttle body over the three bolts protruding from the intake manifold. Thread on the nuts and the one reverse facing bolt in an alternating pattern to ensure a good seal, as well as when you torque them down (not sure of ft/lbs to torque to).
-----------------------)))))

Re-Assemble in reverse of above.

When you get the intake back on, making sure both coolant lines, the TB plug, and the MAF is reconnected, reconnect the negative battery terminal, (if car is COLD) remove the coolant cover (not resivoire) and start the engine. Before the coolant heats up, alternate squeezing the coolant lines coming and going to the throttle body untill you get no more bubbles, or the coolant starts to rise (as this means its heating up) replace the coolant cap, shut off the car, and wait for it to cool down, and repeat untill no more bubbles come out of the coolant.

when there are no more bubbles in the coolant, you can replace the cover for good, and start the car again. this time, let it idle for several minutes so that the engine is fully warm, and adjust the idle stop screw to your liking, I recommend between 500 and 1k rpm like stock. Apply apoxy to screw and let sit overnight.


let me know if I forgot anything, and I will work on getting pictures.
tk-421Dagobah · Jan 27, 2009#25
Thanks for the writeup! Looking forward to the pics... I'm sure they'll be quite helpful as well.
andrubozcentral texas · Jan 31, 2009#26
Prepare the 1zz throttle body by removing any foreign dirt, grease, or whatever.
hold the throttle body Inlet facing you, ECU plug on your right, and you should see the throttle stop screw on the upper right-hand side, may or may not be covered by clear apoxy, regardless, you will need to remove the apoxy if it is present. You will need a small (not sure of size) allen wrench to adjust the idle.
DO NOT.. I REPEAT.. DO NOT try to turn that allen screw until all the epoxy is gone. i stuck a 2mm in there and promptly stripped the snot out of it. 2.5 mm doesn't fit, neither does a 3/32. will have to cut a slot and try to get it out with a screw driver. hopefully it doesn't have some proprietary point on the end and i'll be able to find a replacement.

Who knows what kind of juice melts the last bit of epoxy?
knuckleheadPhilippines · Feb 2, 2009#27
i read the whole thread and im still a bit confused...AlexNet0, were you able to resolve the problem with the idling by using the gasket maker and adjusment of the idle stop screw?how about the cold starting, what is the rpm that you are getting?..is the TB that you installed DBW or the cable type?

im thinking of also doing this mod but i feel a bit apprehensive based on reading this :) ..
AlexNet0Thread starterRockland, ME · Feb 2, 2009#28
cold start idle was 2.7k-3k, it was my own mistake with the oscillating by NOT using the gasket maker, I have no doubt that when I put the 1zz TB back in using the gasket maker I wont have any issues.

I dont think ul have a cold idle problem in the Philippines
yarstarGeorgia · Feb 3, 2009#29
Anybody know how to get the epoxy off safely?

I plan on putting the one I just got on this weekend.

Way cool thread here. I appreciate all that everyone has contributed on this one.

BTW, I already have CAI, catback, NST pulleys, and header. This is the last engine mod I can do without a turbo install.
AlexNet0Thread starterRockland, ME · Feb 10, 2009#30
what did you do tho stop the oscillation?
yarstarGeorgia · Feb 10, 2009#31
Don't get in a rush and crank the car before the gasket maker is set. I made a big mess in my intake by getting ahead of myself.
AlexNet0Thread starterRockland, ME · Feb 10, 2009#32
Oh ok, so the ecu reset cured the oscillation
thebarberGrand Rapids, MI · Feb 11, 2009#33
Originally Posted by Yaris T-Sport ↑
not really
mind sharing what you did?
yarstarGeorgia · Feb 11, 2009#34
Originally Posted by thebarber ↑
mind sharing what you did?
+1
AlexNet0Thread starterRockland, ME · Feb 11, 2009#35
He probably did something with the blitz throttle controller, says he has one on the cardomain link
thebarberGrand Rapids, MI · Feb 11, 2009#36
Originally Posted by AlexNet0 ↑
He probably did something with the blitz throttle controller, says he has one on the cardomain link
i dont see how that would help...
AlexNet0Thread starterRockland, ME · Feb 11, 2009#37
Sooooo...... You swapped internals on the throttle bodies?

Im sorry but I dont really like hit and miss answers, I do appreciate info though, dont get me wrong.
tk-421Dagobah · Feb 11, 2009#38
Originally Posted by Yaris T-Sport ↑
So the trick to cure the oscillation is simply not letting the ECU recognized the 1zz TB, therefor the ECU will function normally as it thinks it is still operating the OEM 1nz TB
So basically you fixed the oscillation problem by not doing anything? I don't get it. 😕
So what if you ever need to reset the ECU in the future? How would you fix then oscillation issue then?
thebarberGrand Rapids, MI · Feb 11, 2009#39
i have to admit, when i had the TB on my car, i never had an oscillation problem

i unhooked the negative terminal....removed the stock tb, installed the 1zz TB with the gasket maker, let it sit for 20 or 30min to set up

then i started the car and let the engine idle for about 10-15min then went for a spin...

never had a problem...
ddongbaphay · Feb 11, 2009#40
A change in airflow is a change in airflow. Theres no way you can really trick different air flow.
yarstarGeorgia · Feb 11, 2009#41
Re-install went well with not vacuum leak this time. I let the gasket maker sit on the new TB overnight and it sealed well. WOW! you can really tell this gives you significant increase in the mid-range and top-end. My car really takes off from about 40mph to 60mph.

New Problem: CEL 🤷


I've disconnected the battery for the night so it will reset the ECU. I'll give it another try tomorrow.

Any suggestions would be appreciated.
yarstarGeorgia · Feb 11, 2009#42
How do I get rid of the CEL light w/o a scangauge? (I hate that light, BTW)
TamagoOff Grid · Feb 11, 2009#43
Originally Posted by AlexNet0 ↑
I hope so, so what should I do, leave it overnight? should I disconnect the battery overnight?
i left a turbo in my passenger floor for two days and it never started spooling 😢

edit: but i left the battery connected...
yarstarGeorgia · Feb 11, 2009#44
T-sport, would you explain that about using the OEM TB?
TamagoOff Grid · Feb 11, 2009#45
Originally Posted by yarstar ↑
How do I get rid of the CEL light w/o a scangauge? (I hate that light, BTW)
either unplug the ecu cables or disconnect the battery ground. with the engine off of course.
anonymous userwindward oahu · Feb 11, 2009#46
Might i also suggest pumping the brake pedal to accelerate situation of removing power from your vehicle. Once brake lights no longer illuminate, voila. You can reconnect the battery terminals again.
TamagoOff Grid · Feb 11, 2009#47
Originally Posted by anonymous user ↑
Might i also suggest pumping the brake pedal to accelerate situation of removing power from your vehicle.
why pump it?
TamagoOff Grid · Feb 11, 2009#48
Originally Posted by yarstar ↑
T-sport, would you explain that about using the OEM TB?
he means, when you re-install your OEM TB your CEL will go away lol.
at3GGVA Beach · Feb 11, 2009#49
will this give a decent upgrade in the power dept? or is it more of a throttle response perk?
yarstarGeorgia · Feb 11, 2009#50
T-sport - you're a FREAKING GENIUS. I never would have thought of that.

Thanks!



🤘