did i miss something? how did he cure it?
Installed the 1zz throttle body -
131 posts · 68,950 views · page 2 of 3
Replies continued
x2Originally Posted by AlexNet0 ↑did i miss something? how did he cure it?
x3
so confused at this point...
so confused at this point...
Somehow the post got removed.
T-sport stated that you take your OEM TB, lay it next to the 1zz TB on the engine, unplug the 1zz and then plug the harness into the OEM TB, turn the car to 'on' but don't crank. Leave it for a few minutes, turn car off, re-plug the 1zz TB.
This, he says, will 'trick' the ECU to thinking the OEM have been reinstalled and fix the CEL. I haven't tried this yet, but it does sound smart.
T-sport stated that you take your OEM TB, lay it next to the 1zz TB on the engine, unplug the 1zz and then plug the harness into the OEM TB, turn the car to 'on' but don't crank. Leave it for a few minutes, turn car off, re-plug the 1zz TB.
This, he says, will 'trick' the ECU to thinking the OEM have been reinstalled and fix the CEL. I haven't tried this yet, but it does sound smart.
so you didnt find out the code on the CEL?
I don't have a scangauge. The damn CEL came on again! Is there anyway to run this w/o getting a CEL? You can really feel the difference in hp. My car has alot of kick now.Originally Posted by thebarber ↑so you didnt find out the code on the CEL?
i left a turbo in my passenger floor for two days and it never started spoolingROFLCOPTER!!!!!!
I used a Generic Scan Tool and the code was P0505 or something like thatOriginally Posted by yarstar ↑I don't have a scangauge. The damn CEL came on again! Is there anyway to run this w/o getting a CEL? You can really feel the difference in hp. My car has alot of kick now.
But the code was: Idle Malfunction.
On another note
I had the TB installed for more than a month and I do have a CEL, but something weird happened..... On two separate occasions I've started the car (first start of the day) and the CEL was gone. It idle was normal, as if I had the stock TB (it didn't went over 2500rpm). But this lasted only one day (that days). The next day the CEL was back on. But it was nice not seeing the annoying light for at least 24 hours 😁
But it was weird sh*t .....
I am 99% sure that the dealer can recalibrate the ECU to compensate for the new TB. I will be making a visit soon, so I'll try to find that out.
I have had the 1ZZ TB on for about 20K miles. No CEL and no Oscillation. Didn't even use a gasket maker. Usually plastic on metal fills in the gaps but you can add a gasket maker for extra insurance.
I have the Simota CAI which might make a difference. Yaris is bit sensitive to the types of intakes it uses and will throw a code. What types of codes are you guys getting?
I have the Simota CAI which might make a difference. Yaris is bit sensitive to the types of intakes it uses and will throw a code. What types of codes are you guys getting?
I also have a Simota SRI with no CELs. Hopefully that won't change when I do the swap.
Originally Posted by tk-421 ↑I am 99% sure that the dealer can recalibrate the ECU to compensate for the new TB. I will be making a visit soon, so I'll try to find that out.
BIG +1 on that. I'd love to know if a dealer could fix the CEL permanently.
I just got a call from the dealer... They're having trouble fitting the OEM hose to the larger-diameter TB. Apparently they've tried putting the hose in some warm water, which makes it more flexible, but they still weren't able to fit it.
How did you guys manage to get it installed?
How did you guys manage to get it installed?
I have a AEM CAI which I had to stretch some to get to fit, but it did fit. I looked at the OEM sitting in my garage before I tried to install the new TB, and saw it might be a significant problem to make work. Maybe getting a slightly larger diameter piece of rubber hosing (the AEM looks like radiator hose) and use that.
Please keep us updated on this TK. I am very interested in whether the dealer can re-calibrate the ECU to keep the CEL from coming on.
Thanks for today's update too. 👍
Please keep us updated on this TK. I am very interested in whether the dealer can re-calibrate the ECU to keep the CEL from coming on.
Thanks for today's update too. 👍
How did you manage to stretch it? I really don't want to start looking for a replacement hose, especially since it may end up being too large for my existing intake.Originally Posted by yarstar ↑I have a AEM CAI which I had to stretch some to get to fit, but it did fit. I looked at the OEM sitting in my garage before I tried to install the new TB, and saw it might be a significant problem to make work. Maybe getting a slightly larger diameter piece of rubber hosing (the AEM looks like radiator hose) and use that.
Please keep us updated on this TK. I am very interested in whether the dealer can re-calibrate the ECU to keep the CEL from coming on.
Thanks for today's update too. 👍
The AEM hose is more pliant than the OEM hose. I heated it in hot water and then worked it on the TB first, then installed the CAI. It was so tight I didn't use a hose clamp. I think you may have to go with the aftermarket, or another OEM hose (Corolla, maybe?).
I just measured the inside diameter of my 1ZZE TB = 60mm. The inside diameter of the OEM hose is 54mm. That's not gonna stretch that far. The hose has to stretch to the outside diameter of the TB, which is approximately 64mm. The rubber is alot thicker on the OEM hose than on the AEM CAI hose. I'd be very impressed if the dealer gets it on. I bet they'll have to use something else. Sorry your having problems.
🙁
I just measured the inside diameter of my 1ZZE TB = 60mm. The inside diameter of the OEM hose is 54mm. That's not gonna stretch that far. The hose has to stretch to the outside diameter of the TB, which is approximately 64mm. The rubber is alot thicker on the OEM hose than on the AEM CAI hose. I'd be very impressed if the dealer gets it on. I bet they'll have to use something else. Sorry your having problems.
🙁
Thanks! I guess I'll have to do that then... I just don't want any fitting issues at the other side of the hose. Hopefully the bracket can get it tight enough to prevent leaks. 😕Originally Posted by yarstar ↑The AEM hose is more pliant than the OEM hose. I heated it in hot water and then worked it on the TB first, then installed the CAI. It was so tight I didn't use a hose clamp. I think you may have to go with the aftermarket, or another OEM hose (Corolla, maybe?).
I just measured the inside diameter of my 1ZZE TB = 60mm. The inside diameter of the OEM hose is 54mm. That's not gonna stretch that far. The hose has to stretch to the outside diameter of the TB, which is approximately 64mm. The rubber is alot thicker on the OEM hose than on the AEM CAI hose. I'd be very impressed if the dealer gets it on. I bet they'll have to use something else. Sorry your having problems.
🙁
BTW, I've asked the rep to check about the ECU compensation thingie. I'll let you know what he tells me for sure. 👍
I had to use an adapter like the one here, and only for an aftermarket aluminum plumbed intake, I cant imagine how you would fit the stock air tube on there.
Picture lost · www.pdm-racing.com
PS, please do let us know if they fix the ECU compensation
Picture lost · www.pdm-racing.com
PS, please do let us know if they fix the ECU compensation
in for an update of if dealer can recalibrate ECU.
Unfortunately I had to back off on the installation. I didn't know that I needed to find an adapter for the hose, and they haven't been able to fit it.
Now I need to pay double: Once for the swap to the 1ZZ TB, and twice because they need to get the OEM one back in there. 😠
I need to go pick up my car in a few minutes. I'll ask them about the ECU recalibration and let you guys know.
Now I need to pay double: Once for the swap to the 1ZZ TB, and twice because they need to get the OEM one back in there. 😠
I need to go pick up my car in a few minutes. I'll ask them about the ECU recalibration and let you guys know.
^just FYI it only took me 20 minutes both to put this in, and 20 to take it off... so I hope they aren't charging you out the a$$ for that.
+1, and I'm not a professional mechanic.Originally Posted by AlexNet0 ↑^just FYI it only took me 20 minutes both to put this in, and 20 to take it off... so I hope they aren't charging you out the a$$ for that.
Yeah I think I can do it by myself as well, although I usually choose to do it through the dealer because I get a 30-day warranty on installation.
I'm currently looking for a silicone coupler to try again. They'll install the TB for free the next time I go for an appointment, so I'm not too mad. 😉
I'm currently looking for a silicone coupler to try again. They'll install the TB for free the next time I go for an appointment, so I'm not too mad. 😉
Im sorry, I dont think I said it correctly, you can only use a coupler like that if you have an aftermarket intake, unless you can take a small piece of aluminum tubing around 2" long to piece it together with.
Anyone know if there is a pronlem installing this throttle body with a AFE intake?
good question, i'd like to know the answer as wellOriginally Posted by hatchbackkid82 ↑Anyone know if there is a pronlem installing this throttle body with a AFE intake?
how does the AFE connect to the TB?
I believe the AFE uses a 45 degree rubber coupler that is sized to the stock TB, please correct me if I am wrong, I do not know if it is stretchable.
If this is indeed the case, then you can use a small piece of aluminum piping and the silicone rubber coupler mentioned before.
If this is indeed the case, then you can use a small piece of aluminum piping and the silicone rubber coupler mentioned before.
I have the TB installed with an aFe intake.
Had to heat up the the rubber coupling in hot water for a bit to make it stretchable enough to fit. Install all nuts on the TB first before trying to put the rubber coupling on as it's thick enough that the TB mounting studs are pressed hard into the sides of the coupling.
Had to heat up the the rubber coupling in hot water for a bit to make it stretchable enough to fit. Install all nuts on the TB first before trying to put the rubber coupling on as it's thick enough that the TB mounting studs are pressed hard into the sides of the coupling.
Installed the 1zz tb today, it was a relatively simple swap. Here's what happened after it was installed:
I let the car sit in the "on" position for 10 minutes
I started the car to get it up to operating temperature
-the idle swung from ~1400 rpm to ~2500 rpm for five minutes then idled at ~1500
I drove around town and some country roads for fifteen minutes, the idle varied while in neutral
I then parked the car and the idling became "normal" and rested around 900 rpm
I shut the car off and drove it again about an hour later...the idle was pretty low, around 600 rpm.
The car now idles around 600 rpm without any oscillation or CEL :)
I DID bypass the coolant lines and I did NOT swap the chip (yet) I'm going to drive around with this setup for a couple of days to see if there are any irregularities before I decide whether or not to swap chips.
Oh, I definitely can feel the difference in my 0-60 distance, it pulls stronger after about 4000 rpm all the way to about 80-90 mph. Great performance mod for under $60
I let the car sit in the "on" position for 10 minutes
I started the car to get it up to operating temperature
-the idle swung from ~1400 rpm to ~2500 rpm for five minutes then idled at ~1500
I drove around town and some country roads for fifteen minutes, the idle varied while in neutral
I then parked the car and the idling became "normal" and rested around 900 rpm
I shut the car off and drove it again about an hour later...the idle was pretty low, around 600 rpm.
The car now idles around 600 rpm without any oscillation or CEL :)
I DID bypass the coolant lines and I did NOT swap the chip (yet) I'm going to drive around with this setup for a couple of days to see if there are any irregularities before I decide whether or not to swap chips.
Oh, I definitely can feel the difference in my 0-60 distance, it pulls stronger after about 4000 rpm all the way to about 80-90 mph. Great performance mod for under $60
on another note, does anyone know the name of the part that the throttle body bolts up to? since the 1zz tb is much wider in diameter than the 1nf tb, the stock cylinder part that the 1zz gets bolted up to blocks a tiny bit of airflow, not allowing the 1zz to maximize its potential. i was wondering what this part is so i could see if i could find a mate for the 1zz tb.
it connects to the intake manifold...Originally Posted by m911gt ↑on another note, does anyone know the name of the part that the throttle body bolts up to? since the 1zz tb is much wider in diameter than the 1nf tb, the stock cylinder part that the 1zz gets bolted up to blocks a tiny bit of airflow, not allowing the 1zz to maximize its potential. i was wondering what this part is so i could see if i could find a mate for the 1zz tb.
right, i didn't know if there was a specific name for the small portion right after the tb...or is that just the intake manifold?Originally Posted by thebarber ↑it connects to the intake manifold...
idk for sure, but a 1zz is used for many toyotas...do they have the 1zz-fe motor? i thought the camry and rav-4 motors were larger?Originally Posted by PK198105 ↑would a TB from either a camry or a rav4 fit? i found some on ebay. or the bolts won't line up.
no, i don't believe it is the sameOriginally Posted by PK198105 ↑
Update:
This morning on the way to school, my car threw 2 CEL's: 2103 and 2111. Basically, the TB valve was stuck on WOT and when I hit the gas from a dead stop, nothing happened...the engine speed did not even increase.
I ended up swapping the chips (sensors) from the two throttle bodies and so far, so good. there is a high rev on cold start ups but after that, it settles down to around 900 rpm...without adjusting the idle set screw.
This morning on the way to school, my car threw 2 CEL's: 2103 and 2111. Basically, the TB valve was stuck on WOT and when I hit the gas from a dead stop, nothing happened...the engine speed did not even increase.
I ended up swapping the chips (sensors) from the two throttle bodies and so far, so good. there is a high rev on cold start ups but after that, it settles down to around 900 rpm...without adjusting the idle set screw.
Once you get that screw adjusted life will be even better. I noticed that with the idle set screw left in the "corolla" position, the transition to DFCO was pretty rough.
With the screw adjusted to a 600-700 rpm warm idle, DFCO transitions are back to near-stock.
With the screw adjusted to a 600-700 rpm warm idle, DFCO transitions are back to near-stock.
I just re-installed the 1zz throttle body, this time with the 1nz chip swapped onto it, and it still oscillates, so im leaving the battery unplugged longer this time. Did anyone have any initial oscillation before it settled on just a high idle?
i think just about everybody had that, i think it's normal.Originally Posted by AlexNet0 ↑I just re-installed the 1zz throttle body, this time with the 1nz chip swapped onto it, and it still oscillates, so im leaving the battery unplugged longer this time. Did anyone have any initial oscillation before it settled on just a high idle?
awesome, now I'm not mad anymore, lol, I get so pissed whenever I try something and it doesnt work, makes me feel so incompetent when I know I'm fully capable, lol
oh i know what you mean, but it'll oscillate back and forth until it finds a happy mediumOriginally Posted by AlexNet0 ↑awesome, now I'm not mad anymore, lol, I get so pissed whenever I try something and it doesnt work, makes me feel so incompetent when I know I'm fully capable, lol
i think i just got a bad 1zz tb, it still just oscillates wildly and doesnt settle at all, even fully warmed up, even with the 1nz chip swapped in. i just put the 1nz tb back on, maybe ill try to get ahold of another1zz tb
i have an extra 1zz tb
First dibs, why did you buy two? are they different serial numbers ? What do you want for it, if it's o.k ? I'm in Canada like you, so shipping should be easy.
Make sure you use a god gasket maker (RTV silicone), and let it sit for 3-5 hours before starting the car.
If you don't let the silicone set up before starting the car, the engine vacuume will suck the stuff into the intake, and you'll get an ocillation and CEL!
If you don't let the silicone set up before starting the car, the engine vacuume will suck the stuff into the intake, and you'll get an ocillation and CEL!
Exactly what I used, I let it set for over an hour, when I pulled it back off after getting the same bad result it was set pretty well. It barely responded to the throttle, meaning that I could not manually hold it in one spot, it would start to, then it just took over, maybe a bad spring in it or something, I dunno.
What codes are you getting...and have you adjusted the idle set screw yet?
I just finished my own TB swap install. I made the chip swap from the start, took the epoxy off the idle screw, and bypassed the TB coolant lines, just as other members have done.
I was unable to find a silicone coupler quickly enough, so I just used a dremel with a filing bit on the inside of the hose until it fit perfectly.
I just took it back from a test drive, and have a BIG smile on my face. No CELs, no weird idle fluctuations, nothing. The only small detail was that it idled at 3K for the first minute or so. After that it steadily went down until it got to 0.5 K.
So now I guess that I shouldn't even need to adjust the idle screw at all. I'll try it out for a couple of days. If nothing happens, I'll just seal the screw again and be done with it.
The difference can be felt right away. And not only did I not notice a power loss at lower revs, but actually a gain! The car pulls a lot better now, even from a complete stop. And the sound is amazing too.
Many thanks to Yaris T-Sport for his excellent idea to swap the chips, and jkuchta for his writeup! 🙇
Now on to the 4-2-1 header... 😆
I was unable to find a silicone coupler quickly enough, so I just used a dremel with a filing bit on the inside of the hose until it fit perfectly.
I just took it back from a test drive, and have a BIG smile on my face. No CELs, no weird idle fluctuations, nothing. The only small detail was that it idled at 3K for the first minute or so. After that it steadily went down until it got to 0.5 K.
So now I guess that I shouldn't even need to adjust the idle screw at all. I'll try it out for a couple of days. If nothing happens, I'll just seal the screw again and be done with it.
The difference can be felt right away. And not only did I not notice a power loss at lower revs, but actually a gain! The car pulls a lot better now, even from a complete stop. And the sound is amazing too.
Many thanks to Yaris T-Sport for his excellent idea to swap the chips, and jkuchta for his writeup! 🙇
Now on to the 4-2-1 header... 😆
Originally Posted by tk-421 ↑I just finished my own TB swap install. I made the chip swap from the start, took the epoxy off the idle screw, and bypassed the TB coolant lines, just as other members have done.
I was unable to find a silicone coupler quickly enough, so I just used a dremel with a filing bit on the inside of the hose until it fit perfectly.
I just took it back from a test drive, and have a BIG smile on my face. No CELs, no weird idle fluctuations, nothing. The only small detail was that it idled at 3K for the first minute or so. After that it steadily went down until it got to 0.5 K.
So now I guess that I shouldn't even need to adjust the idle screw at all. I'll try it out for a couple of days. If nothing happens, I'll just seal the screw again and be done with it.
The difference can be felt right away. And not only did I not notice a power loss at lower revs, but actually a gain! The car pulls a lot better now, even from a complete stop. And the sound is amazing too.
Many thanks to Yaris T-Sport for his excellent idea to swap the chips, and jkuchta for his writeup! 🙇
Now on to the 4-2-1 header... 😆
Hmm now I wanna do this again 😁
i used a Volvo VED12 Semi-truck engine piston squirter nozzle to make my bypass. 😁Originally Posted by kustom play ↑where are you guys getting the connector for the coolant bypass?