Yarisworld Archive

ABS and "!" lights are ON again!

428 posts · 473,304 views · page 8 of 9

Replies continued

403RSCalgary, Canada · Nov 12, 2012#351
Rear hubs
edmscanCanada · Jan 19, 2013#352
I am having the ABS and Emerg Brake light problem. My car has about 170,000 km on it .. and does have ECP extended warranty (the previous owner paid a couple of thousand dollars for this warranty coverage) for another 9 months. Does anyone know if this problem would be fixed under warranty ?

Of course .. the problem has gone away. The lights have gone off .... and speaking to the previous owner it is not uncommon for this problem to appear when the roads are messy, and for the problem to go away for months at a time.

*edit* I spoke to the dealer and they didn't want me to bring my car in .. as the lights have turned off and when they hook the computer up to it, nothing will be shown. So .. they said they won't know if it is the right or left side that is causing the problem. Well .. I don't know but for me checking both sides for corrosion would be a good game plan. But I am not them .. and well I cannot tell them what to do.
GmanQuebec, canada · Jan 27, 2013#353
When I opened mine you could easily see corrosion and I am sure they could also. Luckily the trick of cleaning with circuit cleaner and then packing it with dioelectric grease worked perfect, and now I have traded that car back to Toyota and bought a Corrola.
edmscanCanada · Feb 4, 2013#354
It seems that my car cannot make up its mind what it wants to do. Some days .. the ABS/Emerg light is on and other days it doesn't show its face. I will just ignore it I guess .. and see how that works out.
Bluevitz-rsOshawa, Ontario, Canada · Feb 4, 2013#355
It'll just get worse and worse. The fix is so easy, why ignore it?
edmscanCanada · Feb 4, 2013#356
Originally Posted by Bluevitz-rs ↑
It'll just get worse and worse. The fix is so easy, why ignore it?
I am not a car guy. I know how to check my oil .. and that's about it. So .. fixing it will be something that I may get the dealer to do. But the dang lights won't stay on, so the dealer won't touch it.
yaris2010RSAngus, Ontario · Feb 4, 2013#357
Originally Posted by edmscan ↑
I am not a car guy. I know how to check my oil .. and that's about it. So .. fixing it will be something that I may get the dealer to do. But the dang lights won't stay on, so the dealer won't touch it.
from the sounds of it your sensor is at the point where there is some corrosion but the pins are still intact and no serious damage has been done. it may get to the point where the only thing possible to do is to replace which is much more $$$
DaveToronto · Feb 4, 2013#358
^^^ I agree with this.

edmscan, you really should take a look at it while you still have time to protect the connection before it's completely corroded apart. All you have to do is clean the salt spray and sand off the connector, and then seal it back up with dielectric grease. It takes no more than 10 minutes and will save you all kinds of headaches. The dealer will charge you for an hour's labour, so that'll be $90-110 for a very simple task.

Take a look at this pic for what the sensor looks like:
ABS and "!" lights are ON again!
yaris2010RSAngus, Ontario · Feb 4, 2013#359
Originally Posted by edmscan ↑
I am not a car guy. I know how to check my oil .. and that's about it. So .. fixing it will be something that I may get the dealer to do. But the dang lights won't stay on, so the dealer won't touch it.
thought they didnt use salt out there?
jaggerdogLondon Ontario Canada · Feb 5, 2013#360
The ABS and brake light appeared today not impressed. I retrieved the code and it was 33 for right rear sensor. Pulled the rear wheels off to get better access. Took a while to get the electrical connector off the back of the sensor. I ended up using a medium cotter key split in half. I put it in the lower part of the connector and turned while pulling on the connector towards the center of the car. Blew my mind when I got it off this plug has no rubber seal of weather proofing at all WTF... I dried them both out with a hair dryer and filled them with vasoline. Drove it down the street and BOOM!! it's fixed. When it's not -14 out I will rig up some boots to cover the connectors. They should at lease supply us with some rubber boots that can be slipped over these connectors to prevent the moisture.
edmscanCanada · Feb 10, 2013#361
I have great news .... the local Toyota dealer is going to fix my ABS (!) brake problem, under extended warranty. The extended warranty coverage for my car was purchased by the original owner, and it apparently does cover the ABS (!) issue. So I am looking forward to getting my car finally fixed.

Edit: .. got my ABS (!) issue fixed today at the Toyota dealer. It was good to finally get the problem resolved. The best thing is that it was all covered under ECP warranty.
jp_caldwellCalgary · Mar 2, 2013#362
I have an 06 and just had to clean the sensors for the 2nd time last night. But the bad news is on the passenger side the plug fell completely apart. So I need to replace the ABS sensor wire (part 89516-52090) and the speed sensor (part 89544-52040).

Two questions; does anyone know a site that will ship to Canada and has the parts for a good price. The dealer cost is freaking crazy and more than double what i have found from sites in the US which won't send items north of the border.

Second question, does anyone have DIY for changing the speed sensor?
enviriCT · Mar 2, 2013#363
Picture not included in this copy

you will need a press...at least that's how i removed my hub.

i can maybe send it to you for 100$ shipped from US.
edmscanCanada · Mar 2, 2013#364
All I know is that when the dealer fixed my speed sensor issue (both left and right sides) it took them about 2-3 hours to complete the job. So it doesn't sound like it is a simple 10 min job.
polar_whiteCanada · Mar 20, 2013#365
owner of 2007 LB yaris, had rust proofing done when it was bought new from DVN dealership.

I just got this stupid ABS & (!) lights on problem about few weeks ago, after some googling i found this thread.

I have a service appointment booked and will talk to them to see if they will do a good will pricing for me, if not, i'm not planning to fix it.
polar_whiteCanada · Mar 22, 2013#366
Hi,

Can you tell us which dealership is this in Toronto? DVN wants total of $940 to rplace both rear sensors, they said the cost of both sensors is $240.........

Originally Posted by da1nonly ↑
FOLLOWUP (sorry for the length of this post):

Part replaced for $53.30

So thanks to this forum I had the part replaced by Toyota for $53.30...
out of warranty.

I had the issue back in feb 2010 with the right sensor. they replaced it under warranty but didnt say what caused the issue despite my complaints to know the cause... just said that they had to replace the entire sensor assembly. Back then I complained asking them to recheck and replace the other sensors but they wouldn't becuz they were fine... I didnt actually look this problem up until tonight jan 2011 when the sensor went on the leftside.

So the story goes:
Came in tonight.... told me it would cost $733 to fix the sensor issue. Add $200+ for labor and $100 for the initial diagnostic.

Googled and found this thread.... showed them the easy fix and the tsb issued in 2008 (US version). After talking with service manager, technician and service rep we finally found the TSB (CDN version). I told them to fix the problem according to the TSB which matched the error code found during diagnostic. The replaced just the wire sensor (list price $53.30), waved the diagnostic fee and took 10% off labor (after 1hr of complaining with everyone there). Total was about $230 ($180 2hr labor, $50 part)

I wouldve tried cleaning it but the tech had already pulled out the sensor and showed me the wire was damaged (really?). At least i have the latest sensor model (hopefully) which should protect against corrosion/damage to the sensor. So hopefully I wont have to worry about this or having to clean the original faulty sensor every year.

If it hasn't been posted... for those looking for the TSB (CDN version) the number is:
TSB3027 (issued July 3, 2008 revised on March 19, 2010) - Canadian TSB Version
DTC (diagnostic trouble codes)
C0210 - Rear Speed Sensor RH circuit
C0215 - Rear Speed Sensor LH Circuit

Sorry I didnt get a chance to read the entire thread but I skim through enough of it to help me get the right part replaced at a reasonable price rather than their initial costs of $700-900

Hope that helps.

The service manager also said he'd follow up with Toyota. What they call a good will claim... case determined by toyota canada.

Sorry for the length of the post... but hopefully some of this info helps someone with the same issue.

Cheers.
invisibleghostsWinnipeg · Jul 3, 2013#367
First off let me thank everyone for posting such good information on checking, preventing and replacing in all of the above posts!🎉

I've followed the instructions and have removed both sensors, the first was dirty, but intact, the second....not so lucky.

So I managed to switch out the old, broken, wiring and sensor (I'll call the male end) but I'm a bit lost on the other side (female) end. I had a few pins that were broken off (tons of sand/salt/snow in Winnipeg) and I'm not sure what part or process to use to replace the "female" side? I wasn't able to find anything mentioned in the previous posts on a DIY...any advice?

I've been taking photos as I've gone along and I hope to post them all once I've completely finished to help others. I'll admit I'm not very handy, but I'd rather not pay the dealership for a job that I can do myself!
jb48Quebec, Canada · Oct 19, 2013#368
Now I have a dilemna!
I bought a used (97000 km) 2008 Yaris HB a month ago and it`s my sole everyday vehicle (my other one is a 1984 Suzuki 650 motorcycle). So far so good, no problem at all. In addition to everyday transportation, I use my car for delivering mail to mailboxes in rural area. I read all the 22 pages of this thread and now i have a dilemna: do I take preventive actions to address the potential problem by asking my mechanic to clean and grease the ABS connections when he`ll install my new winter tires or is it better to do nothing per popular proverb <if it ain`t broke, don`t fix it>?
Bluevitz-rsOshawa, Ontario, Canada · Oct 19, 2013#369
Take it apart and grease it with dielectric grease before it's too late.
eseibel67Canada · Mar 9, 2014#370
I've had the ABS & "!" light coming on intermittently since Christmas, and then it went solid for most of the winter so I suspected corrosion. Scan revealed C0210 (right rear speed sensor circuit).

Yesterday it was finally warm and dry enough to take a wheel off and have a look. Turns out that one of the two pin sockets on the harness was crusted up with green corrosion. And I can see why it happened, the plastic housing of the connector had a crack in it that let water in.

Being as I'm a tightwad, I scraped out as much of the crust as possible with a small sewing pin and flushed out the debris with alcohol spray and compressed air. Added a tiny spot of grease in the hole and plugged it in. Cleared the codes by jumping the DLC and the warning lights are now off.

I know this is a temporary repair, so the next time the light comes on I'm going to just replace both rear harnesses.
robkayNW OH · Apr 10, 2014#371
Can somebody help with a question? I'm trying to do the rears. Does that clip on top actually get removed, or is it a molded part of the connector? I lift the clip with a screwdriver, then try to pry to connector back with another screwdriver and the connector doesn't want to slide off easily. The connector is somewhat loose because I can actually slide it back and forth a tad. However, there is significant resistance to sliding the connector off. Am I just being too timid about prying on the connector to pop it off? I just don't want to break it. Thanks,.
CTScottUSA, CT · Apr 10, 2014#372
Originally Posted by robkay ↑
Can somebody help with a question? I'm trying to do the rears. Does that clip on top actually get removed, or is it a molded part of the connector? I lift the clip with a screwdriver, then try to pry to connector back with another screwdriver and the connector doesn't want to slide off easily. The connector is somewhat loose because I can actually slide it back and forth a tad. However, there is significant resistance to sliding the connector off. Am I just being too timid about prying on the connector to pop it off? I just don't want to break it. Thanks,.
The outer clip does need to be removed. Look closely at it and you will see the line where it splits.
robkayNW OH · Apr 10, 2014#373
You're the best CTS! Will try to look closer.
derickveliz2Central, MA · Apr 10, 2014#374
Yes CTScott is the BEST!

D.
CTScottUSA, CT · Apr 10, 2014#375
And even better; I found a picture of releasing the clip from when we did the JDM Vitz RS rear axle swap on enviri's Yaris.

Picture not included in this copy

1 attachment not included in this copy

robkayNW OH · Apr 10, 2014#376
OK, I'm not sure I did it right, but I managed to get the connectors off to inspect them without damaging them. I'm still a little confused, though.

I have a service manual on CD, so I found instructions on page AH-14 -- "AXLE – REAR AXLE HUB AND BEARING" and there it provides the instructions:
DISCONNECT SKID CONTROL SENSOR WIRE (w/ABS)
(a) Using a screwdriver, remove the claw of the connector lock portion and disconnect the skid control sensor wire connector.

NOTICE: Do not remove the connector cover from the connector because the skid control sensor wire may be damaged.
Picture not included in this copy

I could not see any "claw" to remove; in fact I don't think there even is one. What I did is I followed CTScott's instruction (I think...) to remove that clip that you can raise up on top of the sensor with a screwdriver. Well, turns out it is sort of a clamshell like cover that surrounds the whole connector. In my photo below you can see that there is a slotted locking clip that snaps onto a little nub; actually there is one on top and on the bottom. To get the cover off you have to raise both clips and work the thing off.

Picture not included in this copy

With the cover off I took a screwdriver and gingerly worked the connector off. It did finally kind of pop off. I did not find any broken pins or anything.

Is that what I was supposed to do, CTScott? When concerns me is that the manual says "Do not remove the connector cover." Well, if by "connector cover" they mean that clamshell thing that surrounds the connector, that ship done sailed. I did not damage the wires, though, and managed to get it back on OK after reattaching the connector.

When I had the connector off I checked it for that "claw" they said to remove. I did not find any separate part that I could have removed. That's what confuses me about this whole thing.

2 attachments not included in this copy

CTScottUSA, CT · Apr 10, 2014#377
Originally Posted by robkay ↑
OK, I'm not sure I did it right, but I managed to get the connectors off to inspect them without damaging them. I'm still a little confused, though.

I have a service manual on CD, so I found instructions on page AH-14 -- "AXLE – REAR AXLE HUB AND BEARING" and there it provides the instructions:
DISCONNECT SKID CONTROL SENSOR WIRE (w/ABS)
(a) Using a screwdriver, remove the claw of the connector lock portion and disconnect the skid control sensor wire connector.

NOTICE: Do not remove the connector cover from the connector because the skid control sensor wire may be damaged.
Attachment 53232

I could not remove any "claw" to remove; in fact I don't think there even is one. What I did is I followed CTScott's instruction (I think...) to remove that clip that you can raise up on top of the sensor with a screwdriver. Well, turns out it is sort of a clamshell like cover that surrounds the whole connector. You can see that there is a slotted locking clip that snaps onto a little nub; actually there is one on top and on the bottom. To get the cover off you have to raise both clips and work the thing off.

Attachment 53231

With the cover off I took a screwdriver and gingerly worked the connector off. It did finally kind of snap off. I did not find any broken pins or anything.

Is that what I was supposed to do, CTScott? When concerns me is that the manual says "Do not remove the connector cover." Well, if by "connector cover" they mean that clamshell thing that surrounds the connector, that ship done sailed. I did not damage the wires, though, and managed to get it back on OK after replaced the connector.

When I had the connector off I checked it for that "claw" they said to remove. I did not find any separate part that I could have removed. That's what confuses me about this whole thing.

They show to release the connector while it is inside of the cover. That may be possible to do if you can get into just the right position, but I find it much easier to remove the cover. As long as you are careful with the cover removal you will not hurt the wire.
robkayNW OH · Apr 11, 2014#378
So, is that thing they show to pry up in their picture actually a separate piece that you "remove" as they say, or do they mean to just pry it up to release it from a tooth or something? They give you the impression that there is like a clip that you actually pry out and remove. As I said, I looked at the connector carefully and it seemed like it was all one piece to me.

In any case, as you say, it would be pretty tough to get in a position to pry that thing up and pry the connector off at the same time. I agree, it's easier to remove that cover. The wires look delicate, but if you're careful and find any broken I would bet they were already corroded off.

OK, thanks for all your input! (Old subject I know...)

After doing the rear I find that my BRAKE and ABS lights are still on, so I guess I need to check the front now.
CTScottUSA, CT · Apr 11, 2014#379
Originally Posted by robkay ↑
So, is that thing they show to pry up in their picture actually a separate piece that you "remove" as they say, or do they mean to just pry it up to release it from a tooth or something? They give you the impression that there is like a clip that you actually pry out and remove. As I said, I looked at the connector carefully and it seemed like it was all once piece to me.

In any case, as you say, it would be pretty tough to get in a position to pry that thing up and pry the connector off at the same time. I agree, it's easier to remove that cover. The wires look delicate, but if you're careful and find any broken I would bet they were already corroded off.

OK, thanks for all your input! (Old subject I know...)

After doing the rear I find that my BRAKE and ABS lights are still on, so I guess I need to check the front now.

Using this procedure you can find out which one is actually causing the error:
ABS and "!" lights are ON again!
limochongyyz · Apr 15, 2014#380
Can anyone quote me roughly how much does it cost for parts total to replace both rear skid sensors and 2 sensor wires??
Im in canada but U.S. Prices okay just want to see how much... Thanks


Sent from my iPhone using Tapatalk
"G"Chicago · Apr 15, 2014#381
You can't replace just the sensors. Only the wires.
ExiwolfmanWasaga beach · Apr 15, 2014#382
Sensor is I'm the hub unfortunately ull need to replace hub bearing to fix sensor and harness

Sent from my XT1032 using Tapatalk
"G"Chicago · Apr 15, 2014#383
The hub bearing replacement only fixes the sensor, not the harness.
limochongyyz · Apr 16, 2014#384
Yup~ i need to replace both hubs and both wire harnesses.
Can anyone provide me with the costs for parts ?? Thanks


Sent from my iPhone using Tapatalk
derickveliz2Central, MA · Apr 16, 2014#385
Before selling my Yaris I quoted buying all the necessary parts to fix the ABS / BREAK light issue and the cheapest I could get it was for around $250 but getting some genuine Toyota parts it goes up to around $500

Good luck

D.
limochongyyz · Apr 16, 2014#386
Thanks a lot!


Sent from my iPhone using Tapatalk
"G"Chicago · Apr 16, 2014#387
No, we are not dealers.

Originally Posted by limochong ↑
Yup~ i need to replace both hubs and both wire harnesses.
Can anyone provide me with the costs for parts ?? Thanks


Sent from my iPhone using Tapatalk
craigqOttawa · May 18, 2014#388
Well last cleaned in Nov-2010, the ABS and ((!)) light are on again. Cleaned the connections and the lights are not going out this time.
Bluevitz-rsOshawa, Ontario, Canada · May 18, 2014#389
Connections are probably broken now. You'd have to check with small cheap sowing needles and a DVOM. Digital volt and ohm meter.


Sent from my iPod Touch
ExiwolfmanWasaga beach · May 18, 2014#390
Yup that is about right ...had a Yaris in with same problem Saturday will need new hub and harness price around 300$

Sent from my XT1032 using Tapatalk
auxmikeLI, New Yawk · May 18, 2014#391
That's a darn Shame. When I bought my 08 new I couldn't find one with the abs or the side airbags either. Now I'm glad I don't have it. Abs is pretty useless anyways..
craigqOttawa · May 19, 2014#392
Originally Posted by Bluevitz-rs ↑
Connections are probably broken now. You'd have to check with small cheap sowing needles and a DVOM. Digital volt and ohm meter.


Sent from my iPod Touch
Yeah, that'll likely be the next step in the troubleshooting process 🙁 Hopefully it's the rear harnesses and not the sensors pressed into the hubs...
ExiwolfmanWasaga beach · May 19, 2014#393
Originally Posted by craigq ↑
Yeah, that'll likely be the next step in the troubleshooting process 🙁 Hopefully it's the rear harnesses and not the sensors pressed into the hubs...
if u can scan it ...if it shows both sides , take car for spin after code erased when code comes back see if both or just one ..this will eliminate the good one or one that can wait...main problem is that when u get the light ..code.. u have to replace both ( hub ,harness ) cos its the sensor that is 99% gone :( and that will involve a new hub...sorry.
craigqOttawa · Jun 7, 2014#394
Replaced the rear passenger side harness (the rubber boot looked terrible, broken up etc.), that didn't clear it. Disconnected the battery cable, not sure if that's required or not as I can't recall what I did the last time, still didn't help. I then replaced the rear hub w/ABS sensor, disconnected negative battery cable, and that cleared it. Wonder when the driver-side will go 🙁

Don't have a slide hammer so I improvised a pulley-puller by using two 5" bolts and nuts/washers and some spacers to remove the old hub, surprised it worked 😳
robkayNW OH · Aug 25, 2014#395
Just stopping back with an update. In April ('14) I reported that I had removed my sensor cables on the rear, cleaned them and put them back on. (I never did get around to doing the front.) Unfortunately, the BRAKE/ABS indicators did not go out and I just kind of resigned myself to leaving it that way for a while--maybe for good.

Well, about 6 weeks ago the BRAKE/ABS indicators turned off. Not certain the ABS is working again, but they are off. So, for a quick history:
  • My indicators first came on 12/21/13, but then went off the very next day.
  • On 1/27/14 they came on again and stayed on.
  • On 4/10/14 I cleaned the rear connectors, but the indicators stayed on.
  • Sometime in mid-July 2014 the indicators turned off again.
Weirdness. Hoping they stay off, but not counting on it. Still going to pop the fronts off and clean them before cold weather gets here.
sheekeebutMississauga, GTA, Toronto, ON · Feb 10, 2015#396
Digging up this thread. Want to share my experience, which I don't doubt comes from the same problem.

Went to visit the museum last Sunday. Freezing rain, hurrah! Lots of slush and salt downtown as usual. Then, much like all the Torontonians who posted here, I got in the car, started pulling out of the parking garage, and wait, what? An (!) and (ABS) at the same time?

That night, found this thread, took a chance and pulled the rear sensor connectors and blasted the contacts on both ends with CRC MAF sensor cleaner, for lack of other cleaning spray. No dice, errors still stayed on.

Well guess what? Just this morning, like 30 minutes ago, driving down to the office, with error lights on as usual, I was pulling into my parking spot, and, wait, where are those lights? WTF? Just when I was starting to get used to seeing them...

I'm sure I should do those diagnostics per CTScott's info, there must be a dodgy contact somewhere.
robkayNW OH · Feb 10, 2015#397
In my case it was exactly the slushy/salty scenario that seemed to trigger the problem. I am happy to say that even though I only did the rear connectors last April, so far, my indicators have not come back on since last July. The ABS has kicked in a couple times, so I know it works. Now, it is probably accurate to say that, this winter, we have not done as much driving in slushy weather as the winter before. Of course, after I cleaned the rears the indicators didn't go out for 3 months. Did my cleaning actually fix the problem, or was it somewhere else and it finally dried out over the Summer? Who knows. In any case, I'm hoping the problem does not resurface as I do not need that expensive repair. If it happens again I'll clean the fronts and if that doesn't fix it I'll probably just live without the ABS.
IllusionXBrossard, QC · Feb 10, 2015#398
I was looking at digging up this thread. Mine came on a while ago during the ice storm in January. But it quickly turned off as weather warmed up.

I plugged the TechStream tool and it does show rear left sensor issue. I haven't erased it and ABS is working. But the issue I am having now is the rear right wheel locking up.
I haven't seen the ABS light since then, but I still experience rear right wheel locking up, throwing the car to the left until the rest of the ABS system straightens the car...
Logen9FingersChicago · Mar 23, 2015#399
Thank you everyone here. You all have helped me fix my dreaded ABS and Brake light issue. Here is what I went through.

Issue:
ABS and Brake light come on and off. It happens randomly with no Rhyme or reason, and would stay on most of the time. The ABS also kicks in when I roll to a stop; it only happens if I am going slow.

Fix:
Removed back 2 wheels (1 at a time). Sprayed cover to speed sensor harness with WD40. Used flat head screw driver to remove the cover. Cleaned cover with WD40. Disconnected harness from speed sensor (used same screwdriver to gently pry it off). Sprayed dielectric spray inside both ends. Reconnected everything.

So happy I did that this weekend before it started snowing again.
trojjanhorseCanada · Aug 16, 2015#400
Hi everyone

I too own an OBD II bluetooth adapter and like many it did not reveal any fault codes.

I jumped 4&13 and here's the flash pattern i witnessed:

3.3..3.4..3.9..94...repeat

The dots are supposed to be seconds between flashes.

Anyone know what these flash patterns mean?

Thank you.