Replies continued
jkuchtaL.A. · Nov 26, 2008#51No review yet...haven't installed it. I have a stock plastic intake manifold that I'm in the process of spliting open to modify. Once that's done the whole shabang is getting installed, run for a while to make sure a CEL won't come on, and then getting tested on a dyno. I'll keep everyone posted, but I most likely won't have any news until after the holidays.
Happy Thanksgiving everyone!
anonymous userwindward oahu · Nov 29, 2008#52I guess being late to the game, I'm trying to see the real advantages of increasing to another economy car's TB. Would'nt this be good for only 1-3 H.P. max, and then it would also affect FE less proportionally than the gain in HP is worth, right? Or am i missing something?
Once Rich's manifold is produced, was'nt it dynoed on the oem TB?
WolfWingsKansas City, MO, USA · Nov 29, 2008#53Rich's manifold is designed to take either the xD TB or the stock TB. The xD's TB is designed for the 1.8l engine, so it's able to flow a lot more air, helping (especially with Rich's manifold) to let the engine breath dramatically better at higher RPM's.
anonymous userwindward oahu · Nov 29, 2008#54 Originally Posted by
WolfWings ↑ Rich's manifold is designed to take either the xD TB or the stock TB. The xD's TB is designed for the 1.8l engine, so it's able to flow a lot more air, helping (especially with Rich's manifold) to let the engine breath dramatically better at higher RPM's.
Gotcha, Thanks WW. I may be out looking for a new TB then. 🙂
YarisPRMayaWest, Puerto Rico · Dec 19, 2008#55yesterday I found one foe $55......... I might go back and grab it....
gwasabiHonolulu, Hawaii · Dec 19, 2008#56The corolla TB throws a CEL light. T-T i dunno y
FunctionSpec626, Southern California · Dec 19, 2008#57Reset ECU and check make sure all the air bubbles are out of the coolant lines that go into the throttle body. Also check the connector the TB to make sure its on correctly.
Disconnect negative battery cable for a couple hours to completely reset the ECU. Usually leaving it disconnected overnight would be best.
gwasabiHonolulu, Hawaii · Dec 19, 2008#58how do i make sure all the air bubbles are out of the coolant lines?
I did reset the ECU though. it kinda like does this wierd thing when slowing down too. like it revs up then and down by itself. I dunno whats up with that but maybe I'll try reset ecu again
FunctionSpec626, Southern California · Dec 19, 2008#59Yeah sounds like theres air in your coolant lines.
Once the car cools down, take off radiator cap. Turn on car and let it run at idle. Let it warm up. You'll see air bubbles bubbling out of the coolant. GENTLY squeeze the smaller coolant tubes in various areas to help push the rest of the air out. It'll be kinda hot so don't burn yourself. Keep doing until you see no more air bubbles coming out and your done.
PETERPOOPThread starterOahu · Dec 19, 2008#60 Originally Posted by
YarisPR ↑ yesterday I found one foe $55......... I might go back and grab it....
pick it up for me and i'll buy it from you if it's legit.
ztrack157Biggs, CA · Dec 20, 2008#61I nabbed a corolla TB today for $45.00 plus shipping I want to see what this does. Peter I might sell it to you if I don't like it.
PETERPOOPThread starterOahu · Dec 20, 2008#62ah thanks for the offer, but i am wanting the xD throttle body,not the carolla.
YarisPRMayaWest, Puerto Rico · Dec 20, 2008#63I got a 05 Corolla TB and the instalation was clean, nice and easy. The car iddles normally but it won't go over 2000rpm.... What could be the problem?
anonymous userwindward oahu · Dec 20, 2008#64 Originally Posted by
YarisPR ↑ I got a 05 Corolla TB and the instalation was clean, nice and easy. The car iddles normally but it won't go over 2000rpm.... What could be the problem?
Possible vacuum leak.
YarisPRMayaWest, Puerto Rico · Dec 20, 2008#65I just putted the intake just touching the TB I did't connect it. And as soon as I moved it a little the car turned off. I might have to try it with everything connected.
thebarberGrand Rapids, MI · Dec 20, 2008#66what did you use for a gasket?
YarisPRMayaWest, Puerto Rico · Dec 20, 2008#67 Originally Posted by
thebarber ↑ what did you use for a gasket?
I just tooked out the Yaris TB and place the Corolla TB. Do I need something else? What gasket?
I think I'am doing something wrong..
thebarberGrand Rapids, MI · Dec 20, 2008#68Picture not included in this copy
gwasabiHonolulu, Hawaii · Dec 22, 2008#69i didn't really need to use gasket in a tube for the tb install....works fine. also this mod is pretty awesome. you can feel the difference. more responsive in higher rpms and sounds hella awesome.
anonymous userwindward oahu · Dec 23, 2008#70 Originally Posted by
gwasabi ↑ i didn't really need to use gasket in a tube for the tb install....works fine. also this mod is pretty awesome. you can feel the difference. more responsive in higher rpms and sounds hella awesome.
How easy was the install, and where did you get the TB?
gwasabiHonolulu, Hawaii · Dec 23, 2008#71got mine from barber. Install was SUPER easy. it goes right in. and just stick all the pipes back into the right places. took me about 30 min to install. shouldn't be too hard if you have aftermarket intake. If you have stock intake it might take u a little longer
AlexNet0Rockland, ME · Jan 1, 2009#72i like the sound of this, lol
what is the size of the 1zz TB inlet compared to the 1nz? Would one need a different size intake tube for it, or would the rubber couplers for a CAI stretch over it neway?
gwasabiHonolulu, Hawaii · Jan 1, 2009#73My rubber couple stretched all the way. I think it depends on the intake brand because the one i have is smaller than the TB. I'm probably going to find a new pipe though so I can make the intake bigger. It's like about .5 inch difference i think not too sure. It's hell of a lot bigger than the stock yaris TB
AlexNet0Rockland, ME · Jan 1, 2009#74I cant wait to find one to buy, Even after just installing a CAI I can feel a difference, I cant imagine what the more drastic modders feel from their Yaris