Yarisworld Archive

Prius Pistons

119 posts · 58,089 views · page 1 of 3

sdyarisOriginal postSioux Falls · Nov 6, 2008#1
I was just reading that the compression ratio for the Prius is 13:1. Would the higher compression pistons work in the Yaris (10.5:1)?

Replies 118

Nexus1155Dorchester · Nov 6, 2008#2
HAH! im glad someone brought this up again, I've read places that the compression is due to the fact of the pistons themselves and will fit since the blocks are of the same cast.

The main difference is that the prius pistons are domed? or of a different design. I have heard that they give off the bat a 13-15hp gain. They would be great for N/A with some tuning, but not for FI

If you have time to swap them on the weekend, go for it. They are cheap and all you would need are new head studs as these ones on this block stretch i think and cannot be reused... also cheap to do.. I doubt you would need an engine lift if you and buddy was over(I lifted an H22, back breaking but i could move it...)

If you have any questions i'll try to answer them to the best of my ability...
mikenacaratoBrentwood, TN · Nov 6, 2008#3
on the yaris will it do much for compression to run a thinner head gasket? im not sure how much material is there to work with though.
but on the other hand this piston idea seems pretty awesome.
cali yarisCanoga Park, CA · Nov 6, 2008#4
What is the displacement of the Pruis motor? I have one, and it looks nothing like our 1.5L
RagnaCaTVillalba, Puerto Rico · Nov 6, 2008#5
Sounds like a go but engine Temp could become an issue? Maybe an Oil cooler could be used? I like N/A performance!
mikenacaratoBrentwood, TN · Nov 6, 2008#6
i think 1496 is the prius displacement
cali yarisCanoga Park, CA · Nov 6, 2008#7
yeah an N/A project would be really fun. 13:1 pistons with ITBs FTW!
RagnaCaTVillalba, Puerto Rico · Nov 6, 2008#8
Originally Posted by cali yaris ↑
What is the displacement of the Pruis motor? I have one, and it looks nothing like our 1.5L
Yes Garm 1.5 and stay away from this you are going to blow something up!
mikenacaratoBrentwood, TN · Nov 6, 2008#9
i would love itbs more than anything. i have a spare set of itbs off of my yzf600 i should start making my own project! haha
Nexus1155Dorchester · Nov 6, 2008#10
lol good luck with the drive by wire system and all with the itb's, its a pain in the ass, you would not see gains in compression with a thinner headgasket, but if you machined either the block or the head, 10thousandths of an inch you would raise it about .5 points.... I do not know if there is room to do this to begin with so...

and about heat being an issue, it can only be told by the person who does it and monitors the heat... the prius doesn't overheat? But i don't know how the atkinson system kicks in and at what variables
mikenacaratoBrentwood, TN · Nov 6, 2008#11
i guess to run the itb you would have to run an engine management system and physically weld in all of your brackets and cables for the throttle cable.

can you get a tune that will let you disable or bypass the drive by wire?
Nexus1155Dorchester · Nov 6, 2008#12
ehhhhhhh, doesn't work that way lol.... Unless you get either an XB or an Echo ecu and wire it up somehow along with the throttle cable and pedal... BUT they do have drive by wire ITB's out there now.. so. yeah...

Or you could hookup a cable to the current pedal and use both, and have a new throttle body on there while the stock one is in a different locations receiving electronic signals to relay to the ecu...
mikenacaratoBrentwood, TN · Nov 6, 2008#13
hmm, so there not a single place that can reflash or piggyback to the yaris ecu and allow you to remove drive by wire?
Nexus1155Dorchester · Nov 6, 2008#14
i was working on a reflash, but i have other priorities. Well i mean, you could try and toss on an echo throttle body with pedal and cable and see if it will work, some things are whacky like that but you'll probably get a CEL...
RagnaCaTVillalba, Puerto Rico · Nov 6, 2008#15
Originally Posted by Nexus1155 ↑
and about heat being an issue, it can only be told by the person who does it and monitors the heat... the prius doesn't overheat? But i don't know how the atkinson system kicks in and at what variables
True but the engine is not constantly on cuase it's a hybrid also the atkinson cycle is very different with TDC against our design but don't know but still sounds fun! I guess!🙂
sdyarisThread starterSioux Falls · Nov 6, 2008#16
Heh, i wouldn't have the nerve to try it until the car is paid off. 😆
at3GGVA Beach · Nov 6, 2008#17
itbs=?? indidual throttle bodies? 🤷
toyochrisPuerto Rico · Nov 6, 2008#18
yes itb are individual throtle bodies.
at3GGVA Beach · Nov 6, 2008#20
thanks guys
RagnaCaTVillalba, Puerto Rico · Nov 6, 2008#21
Originally Posted by toyochris ↑
yes itb are individual throtle bodies.
Hey ToyoChris bet you are already looking in to this right? I Know we are like that. He he he
rob323Joyner, Brisbane · Nov 9, 2008#22
I have some pdf's on the 1NZ-FXE (Prius motor) and the specs are ever so slightly different for the Prius piston diameter but everything seems to be the same.
Not sure on what sort of timing advance the Prius runs compared to a 1NZz-FE though.
TamagoOff Grid · Nov 9, 2008#23
didn't read the whole thread but...

http://en.wikipedia.org/wiki/Atkinson_cycle


the 1nzfxe in the prius is not a normal 4stroke engine.. but hey, as long as the valves clear the pistons and the connecting rods are of the same length, you should be OK
cali yarisCanoga Park, CA · Nov 9, 2008#24
this Prius piston discussion is just to save money, right? Because you could order pistons from CP with any specs you want, including high compression for the 1NZ-FE
06silveryarisPuerto Rico · Nov 9, 2008#25
as far as the prius pistons what concerns me but just very little would be the fact of pinning. Can the factory ECU make the fuel adjustment or would just running higher octane cure it if it happened? As far as ITB's go with the yaris engine being smaller you can probably use GSX-R itb's and make a manifold once the drive by wire issue is solved. I have a very close friend that had been making manifolds for ITB's for Hondas for quite some time and they work out nicely. I can post some pics of he last one he made for a integra once I figuere out how to make the pics smaller or I can email if you PM me.
06silveryarisPuerto Rico · Nov 9, 2008#26
here are some pics. Hope you guys like🙂

2 attachments not included in this copy

06silveryarisPuerto Rico · Nov 9, 2008#27
by the way I know there is a ITB thread I do not mean hijack this thread🙂
cali yarisCanoga Park, CA · Nov 9, 2008#28
um, then post in it, LOL
mikenacaratoBrentwood, TN · Nov 9, 2008#29
haha, nice setup though. i got a set of itbs in my garage from my bike i want to do that with.
toyochrisPuerto Rico · Nov 9, 2008#30
Originally Posted by RagnaCaT ↑
Hey ToyoChris bet you are already looking in to this right? I Know we are like that. He he he
you know it but no money cuase my newest mod is that i am a DAD!!!
YarisPRMayaWest, Puerto Rico · Nov 10, 2008#31
RanaCat, 06SilverYaris, ToyoChris

We have to make a meeting

Hay que ruinirnos pq hay muchas ideas y ustedes saben muchas de esto que yo. Q tal?
RagnaCaTVillalba, Puerto Rico · Nov 10, 2008#32
Originally Posted by toyochris ↑
you know it but no money cuase my newest mod is that i am a DAD!!!
HEY! That was my MOD! Very soon DECEMBER, I'm modding the stroller with a set of 7" inch rims and Toyota Badge! LOL!
RagnaCaTVillalba, Puerto Rico · Nov 10, 2008#33
Originally Posted by YarisPR ↑
RanaCat, 06SilverYaris, ToyoChris

We have to make a meeting

Hay que ruinirnos pq hay muchas ideas y ustedes saben muchas de esto que yo. Q tal?
Sounds good! Hace tiempo que quiero janguiar con pal de yaris y esto de los pistones de Prius puede Bregar. Yo tenia un 4A-FE con pistones 7A y UFF!
kargoboySt. Augustine, FL · Nov 10, 2008#34
CP should be releasing Pistons for the 1NZ-FE shortly. At least, that's what my supplier is
telling me.
Flipper_1938Kentucky · Jul 28, 2011#35
Did anybody ever lay there hands on a set of prius pistons to see what the difference was between those and the Yaris pistons?
IVAN_TRDPUERTO RICO · Aug 2, 2011#37
in puerto rico, we use prius pistons
Flipper_1938Kentucky · Aug 4, 2011#38
Originally Posted by IVAN_TRD ↑
in puerto rico, we use prius pistons
To build high performance Yaris motors?
IVAN_TRDPUERTO RICO · Aug 6, 2011#39
yaris and echo
cali yarisCanoga Park, CA · Aug 6, 2011#40
^ I keep seeing posts like this, and never a picture or a dyno. I believe you -- but it would be real nice to see how it's done and what the result is.
Maitre_Te_TeQuébec · Sep 17, 2011#41
Originally Posted by cali yaris ↑
^ I keep seeing posts like this, and never a picture or a dyno. I believe you -- but it would be real nice to see how it's done and what the result is.
X2... I want to see this on video and dyno run! Do you have this?

If I find a cheaper engine, I will try this mod.
Betriventedmonton · Sep 21, 2011#43
j'imagine.. lol (Sorry, nonconstructive post but this was funny)
Maitre_Te_TeQuébec · Sep 21, 2011#44
Originally Posted by Betrivent ↑
j'imagine.. lol (Sorry, nonconstructive post but this was funny)
loll.. I have correct it :P
10 FrancisTexas · Feb 18, 2012#45
Personally, I would be more interested in the Prius intake cam than Prius pistons. The effective compression ratio on the Prius changes due to VVT-i, but I've been told by experienced techs that it's around 6.5-7.5:1, depending on valve timing. The interesting thing to me would be a Prius intake cam and a supercharger- turn the Yaris engine into a Miller-cycle engine.
2greek4uMontreal,QC · Mar 6, 2012#46
Originally Posted by cali yaris ↑
^ I keep seeing posts like this, and never a picture or a dyno. I believe you -- but it would be real nice to see how it's done and what the result is.
On every Forum too... but they never show anything it's like a secret voodoo cult!
spin_kingbarbados · Apr 15, 2012#47
i wanted to raise my compression but couldnt find any for my vitz rs. i would like to know how if anyone has tried the 13:1 compression. what year prius pistons were used & if any addition fabrication work had to be done.
GolddeenohColumbia, SC · Apr 15, 2012#48
Originally Posted by 2greek4u ↑
On every Forum too... but they never show anything it's like a secret voodoo cult!
oh yes I like the voodoo as long as i can see it doo its voo. until then it is like the sneaking myth of the 1k hp streetable hatch back that hunt down and devours v-8s.

and the getting another engine and building a n/a to do autocross would be a sweet project, i'm trying to get my pops in on a project with me but he is hesitant to do anything.
cali yarisCanoga Park, CA · Apr 15, 2012#49
We can get new higher comp pistons, just sold some to a customer doing an NA build.

Sourcing Prius pistons are cheaper obviously IF they work.
mr_milesPortland, OR · Apr 16, 2012#50
Wish i had a spare engine...I'd tear it down and find out.