Replies continued
Nanoss22Puerto rico · Apr 23, 2012#51Guys here in puerto rico i have seen 2 hb with the prius piston mood and it work they fit perfectly no mood needed just replace the stock ones with the prius piston and the roods are the same original that came with the engine 1nzfe .....only the pistons.. Prius 2004 2006... I have allready the piston all assembled waiting for the mechanic...
1 attachment not included in this copy
Nanoss22Puerto rico · Apr 23, 2012#52I need a repair manual for the 1nz fe engine so i can get all the timing all the screw torque if u know i will apreciated
why?harnett county NC · Apr 24, 2012#53in the diy section:2007 Repair Manual.
And we'd love to see some build pics and a dyno run if you do it after too.
Thank you!
Would be so cool if it worked.
1.5Tampa · Apr 24, 2012#54finally someone with proof of actually doing this.
Nanoss22Puerto rico · Apr 24, 2012#55Yeah I will keep uploading photos when I finish the project and dynocharts afterwards....
Flipper_1938Kentucky · Apr 25, 2012#56I would like to see pics of the yaris and prius pistons side by side.
cali yarisCanoga Park, CA · Apr 25, 2012#57I'd like to see ANY pics of Prius pistons.
GolddeenohColumbia, SC · Apr 25, 2012#58^ isn't that what he showed the page before?
or do you just want the piston by its self?
cali yarisCanoga Park, CA · Apr 25, 2012#59^ Neither. I want to see these put into a car -- which it looks like he's going to do so we can all finally see it for real, and get to see some results, whatever they are.
Props to Nanoss22.
GolddeenohColumbia, SC · Apr 25, 2012#60oh I see, yes i look forward to seeing the out come, maybe even a base line dyno and and after piston dyno as well, then we could get an estimate of how much gain the pistons do.
ViperoniBrampton, ON · Apr 25, 2012#61Mad props to Nanoss for making it happen!
Could be a fairly cheap way to gain 10-20hp.
Nanoss22Puerto rico · Apr 26, 2012#62Today i got all the torque needed to mount the piston it may take 1 to 2 weeks to make this project because the mechanic disponibility i am excited to get it done...
Nanoss22Puerto rico · Apr 26, 2012#63Here the proof prius pistons on toyota echo 1nz fe roods this ones are used just ran 1 900miles on a yaris hb a friend of mine sold it to me i only buy new the piston rings and the roods bearing
2 attachments not included in this copy
GolddeenohColumbia, SC · Apr 26, 2012#64MONKEYS!!!!!!!!!
:D
ViperoniBrampton, ON · Apr 27, 2012#65Nanoss22, Was 91 octane gas ok, or did you have to run higher?
1.5Tampa · Apr 27, 2012#66Sweeeeeeeettttt
Flipper_1938Kentucky · May 9, 2012#67 Originally Posted by
Nanoss22 ↑ Here the proof prius pistons on toyota echo 1nz fe roods this ones are used just ran 1 900miles on a yaris hb a friend of mine sold it to me i only buy new the piston rings and the roods bearing
Any progress to report?
jounabayamon puerto rico · May 9, 2012#68i am planing to do this i am from puerto rico and i am studying to be a licensed mecanic so ill be doing it myself in the workshop i just need to find the pistons and the piston rings ive checked ao many times the fitment it aint even funny its a bolt on tune
yaris 2szgreece · May 12, 2012#691.5Tampa · May 12, 2012#70UPdates!!!
BTW Nanoss2, your sedan looks clean lets see more pics.
Nanoss22Puerto rico · May 16, 2012#71Sorry people for not updating i have posponed the mods to summer... i am waiting for my baby boy to born on this late May... I am in debt with u guys sorry for keep u waiting...
JustDidItUnited States · Feb 20, 2013#72 Originally Posted by
Nanoss22 ↑ Sorry people for not updating i have posponed the mods to summer... i am waiting for my baby boy to born on this late May... I am in debt with u guys sorry for keep u waiting...
Any chance of this project picking up here in 2013?
I'm tempted to try this on my 1NZ-FXE - that is swap the cams and cam gear from the 1NZ-FE keeping my stock Prius pistons and running some sort of EM.
4/20 NEVER FORGETPortland, OR · Feb 20, 2013#73Seriously. I was just thinking about this thread. Babies ruin everything!
JustDidItUnited States · Feb 20, 2013#74Jason@SportsCarDebary, FL · Feb 20, 2013#75 Originally Posted by
JustDidIt ↑
I have a brand new set in the box, as well as a used set. Also have a couple of spare heads. PM me if you are interested.
JustDidItUnited States · Feb 22, 2013#76 Originally Posted by
Jason@SportsCar ↑ I have a brand new set in the box, as well as a used set. Also have a couple of spare heads. PM me if you are interested.
PM'd
Autocross72Seattle · Mar 3, 2013#77I have hard of people doing the Prius piston swap before, but they always seem to disappear. I think the reason is that they are cast pistons with too much compression. At 13:1 compression, you would have to run full race gas, which at $9.00 a gallon would be extremely expensive. Also, cast pistons can't withstand that kind of compression for very long. You would need to go with forged pistons. You should also swap out the crapy stock Yaris rods while you are at it. They are known to be weak and the turbo guys have shown over and over again that they can't with stand much of a power increase.
cali yarisCanoga Park, CA · Mar 3, 2013#78 Also, cast pistons can't withstand that kind of compression for very long. You would need to go with forged pistons.
That doesn't make sense if the Prius runs them as stock pistons? 🤷
etherdudeMass., USA · Mar 3, 2013#79 Originally Posted by
cali yaris ↑ That doesn't make sense if the Prius runs them as stock pistons? 🤷
The Prius Atkinson Cycle cams have the effect of lowering cylinder pressure due to holding the intake open longer and blowing intake charge back into the intake manifold. Thus the higher compression 13:1 pistons do not result in necessarily higher cylinder pressures that the lower compression ration Yaris pistons.
ViperoniBrampton, ON · Mar 3, 2013#80 Originally Posted by
etherdude ↑ The Prius Atkinson Cycle cams have the effect of lowering cylinder pressure due to holding the intake open longer and blowing intake charge back into the intake manifold. Thus the higher compression 13:1 pistons do not result in necessarily higher cylinder pressures that the lower compression ration Yaris pistons.
QFT
Basically the dynamic CR of the 1nz-fxe probably isn't that much different than the DCR of the 1nz-fe... 13:1 is a very high static CR to start off on a regular fuel injected motor, ESPECIALLY with the stock cams.
It's just too bad nobody's come back and said what's happened.
why?harnett county NC · Mar 3, 2013#81I remember reading the highest the Prius ratio ever gets is 11.1. The atkinson cycle keeps both the intake and exhaust valves open for long periods of time.
JustDidItUnited States · Mar 4, 2013#82 Originally Posted by
why? ↑ I remember reading the highest the Prius ratio ever gets is 11.1. The atkinson cycle keeps both the intake and exhaust valves open for long periods of time.
Wonder what kind of performance increase could be expected as going from the 10.5:1 to the 11:1 or whatever the CR would be..
When I do the Cam and Cam gear swap I would basically have the 1NZ-FE head but still the Prius bottom end. Where someone else with the 1NZ-FE would have to tear into the block and switch the pistons but hopefully leaving the stock 1NZ-FE crank. The 1NZ-FXE Does have different pistons and crankshaft but same rods. Would be really interesting to see if there would be a difference it would make between the 1NZ-FXE and 1NZ-FE crank obviously other than part #s being different..
JustDidItUnited States · Mar 4, 2013#83I'm still on the hunt for a set of 1NZ-FE cams and cam gear. I'd rather not go and pick up a full long block for $400-$600 - but i may have to. I'd rather just snatch a full 1NZ-FE head or even just the cams and gear.
I really want to try this out.
ViperoniBrampton, ON · Mar 5, 2013#84 Originally Posted by
JustDidIt ↑ Wonder what kind of performance increase could be expected as going from the 10.5:1 to the 11:1 or whatever the CR would be..
When I do the Cam and Cam gear swap I would basically have the 1NZ-FE head but still the Prius bottom end. Where someone else with the 1NZ-FE would have to tear into the block and switch the pistons but hopefully leaving the stock 1NZ-FE crank. The 1NZ-FXE Does have different pistons and crankshaft but same rods. Would be really interesting to see if there would be a difference it would make between the 1NZ-FXE and 1NZ-FE crank obviously other than part #s being different..
The (static) CR would be 13:1 if you use Prius (FXE) pistons.
The dynamic CR is apparently 11:1 if you use FXE pistons.
I was under the impression that the FE & FXE cranks were the same... or at least the stroke is. Maybe the FXE crank is stronger somehow?
To answer your question, it depends. A quick googling seems to say that there's diminishing returns, especially since you're not improving the breathing of the motor and filling the combustion chamber with more air/fuel.
One calculator said 6.5% and that's more or less what I read on another site as well... which I think is a bit low, but could be bang on. In any case, a 6.5% increase is 7hp.
If possible, I'd go with an overbore Prius piston to help increase displacement at the same time as increasing the CR... that'll help engine breathing, and it'll increase the quench area inside the combustion chamber which should help stop some detonation too.
JustDidItUnited States · Mar 5, 2013#85 Originally Posted by
Viperoni ↑ The (static) CR would be 13:1 if you use Prius (FXE) pistons.
The dynamic CR is apparently 11:1 if you use FXE pistons.
I was under the impression that the FE & FXE cranks were the same... or at least the stroke is. Maybe the FXE crank is stronger somehow?
Crankshaft:
1NZ-FE: 13401-210
20 1NZ-FXE: 13401-210
40 Difference 😕 No idea...
Originally Posted by
Viperoni ↑ To answer your question, it depends. A quick googling seems to say that there's diminishing returns, especially since you're not improving the breathing of the motor and filling the combustion chamber with more air/fuel.
One calculator said 6.5% and that's more or less what I read on another site as well... which I think is a bit low, but could be bang on. In any case, a 6.5% increase is 7hp.
If possible, I'd go with an overbore Prius piston to help increase displacement at the same time as increasing the CR... that'll help engine breathing, and it'll increase the quench area inside the combustion chamber which should help stop some detonation too.
So what if I was to modify the induction system..different routed intake and intake manifold (been looking over making my own intake manifold after watching 'tooters' adventures...and exhaust manifold and exhaust system? I would think this would help some...right?
why?harnett county NC · Mar 5, 2013#86crank is the same. They'd use a different part number if it was different. It is really all about pistons and the timing. the atkinson cycle doesn't give a damn about low end tourque, unlike the normal otto cycle.
JustDidItUnited States · Mar 6, 2013#87 Originally Posted by
JustDidIt ↑ Crankshaft:
1NZ-FE: 13401-21020
1NZ-FXE: 13401-21040
Originally Posted by
why? ↑ crank is the same. They'd use a different part number if it was different. It is really all about pistons and the timing. the atkinson cycle doesn't give a damn about low end tourque, unlike the normal otto cycle.
Read much of the other posts??
GolddeenohColumbia, SC · Mar 6, 2013#88^ burn
^LMAO
tooterLos Angeles · Mar 6, 2013#90 Originally Posted by
Viperoni ↑ QFT
It's just too bad nobody's come back and said what's happened.
That would seem to indicate that trying to run Atkinson pistons in an Otto engine did not go well.
Here's a fascinating animation of how Atkinson cycle engines work:
http://www.youtube.com/watch?v=hEfOxKmCstg Skip to 2:20 second mark to get past the bullshit.
JustDidItUnited States · Mar 6, 2013#91 Originally Posted by
tooter ↑ That would seem to indicate that trying to run Atkinson pistons in an Otto engine did not go well.
Ahhh.. Come'on Tooter...you of all people... lol - I'd like to see more optimism. The better answer would be, most people are too skurd to try it - Those who have...don't post here on YW...or just have better things to do than post cool EUREKA DIYs ... Like your manifold. :)
I've found a FULL 2012 Yaris 1NZ-FE cylinder head super cheap. Now just waiting to hear back if I can have it shipped or if I have to go pick it up.
xnamerxxso cal · Mar 6, 2013#92I wouldn't take the crank having a different part number as meaning anything more then it might not have a standard bolt pattern or it might require a longer snout.
Picture not included in this copyHere is a cutout of a 1nz-fxe from an autoshow.
You can see the giant mechanical flywheel, which doesn't have provisions for a starter and you can see the giant start/stop starter on the front of the engine.
I seriously doubt that the FXE piston would have any issues in the FE engine aside from the massive increase in compression that would cause some tuning issues. The compression being close to 13:1 doesn't really scare me as long as you can control the tune, which is pretty much only possible with a aftermarket ECU. I've seen 4.6l engines running 12.6:1 on 91 octane its doable just takes more work.
The piston being HYPEREUTECTIC doesn't mean it can't handle power it just means the piston is less elastic than a forged piston, meaning when its given a shock like say detonation it doesn't deform as much so if the material sees a strong shock it will crack rather than deform. Hypereutectic pistons have some great properties about them that make them suitable choices for performance oriented situation like the fact they have little heat deformations which means they don't compress and swell as much with heat which means you can run a piston tighter in the bore and you can also run a lighter piston which makes the engine more efficient.
ViperoniBrampton, ON · Mar 6, 2013#93Here's another thought; since 13:1 *may* be on the high side... are there thicker head gaskets we can use?
tooterLos Angeles · Mar 7, 2013#94 Originally Posted by
JustDidIt ↑ Ahhh.. Come'on Tooter...you of all people... lol - I'd like to see more optimism.
Sorry, I really didn't mean to come off as being negative. I was only commenting on the lack of feedback as to what happened
after 13:1 pistons were installed. There's no information. I'm all for trying new things. Wait till you see what I'm cooking up... 😉
The better answer would be, most people are too skurd to try it - Those who have...don't post here on YW...or just have better things to do than post cool EUREKA DIYs ... Like your manifold. :)
That manifold wasn't even my idea. I can't take credit for it. The guys in Puerto Rico did it first. I just thought it looked really cool and wanted one on my engine.
I've found a FULL 2012 Yaris 1NZ-FE cylinder head super cheap. Now just waiting to hear back if I can have it shipped or if I have to go pick it up.
Sounds good! 👍
The Atkinson engine is really strange. Did anyone notice that it fires on every revolution?
JustDidItUnited States · Mar 7, 2013#95 Originally Posted by
xnamerxx ↑ Picture not included in this copyHere is a cutout of a 1nz-fxe from an autoshow.
Sooo Pretty! 👍
Originally Posted by
xnamerxx ↑ I seriously doubt that the FXE piston would have any issues in the FE engine aside from the massive increase in compression that would cause some tuning issues. The compression being close to 13:1 doesn't really scare me as long as you can control the tune, which is pretty much only possible with a aftermarket ECU. I've seen 4.6l engines running 12.6:1 on 91 octane its doable just takes more work.
Originally Posted by
Viperoni ↑ The (static) CR would be 13:1 if you use Prius (FXE) pistons.
The dynamic CR is apparently 11:1 if you use FXE pistons
To answer your question, it depends. A quick googling seems to say that there's diminishing returns, especially since you're not improving the breathing of the motor and filling the combustion chamber with more air/fuel.
One calculator said 6.5% and that's more or less what I read on another site as well... which I think is a bit low, but could be bang on. In any case, a 6.5% increase is 7hp.
Originally Posted by
Viperoni ↑ Here's another thought; since 13:1 *may* be on the high side... are there thicker head gaskets we can use?
If your original post is correct, then most I may need to change when running 11:1 compression is 91 instead of 87 pump gas, besides some EM. But even then....I run on 87 now...at the supposed static CR of 13:1 or dynamic 11:1.
Originally Posted by
tooter ↑ Sorry, I really didn't mean to come off as being negative. I was only commenting on the lack of feedback as to what happened after 13:1 pistons were installed. There's no information. I'm all for trying new things. Wait till you see what I'm cooking up... 😉
That manifold wasn't even my idea. I can't take credit for it. The guys in Puerto Rico did it first. I just thought it looked really cool and wanted one on my engine.
If if you weren't the original.. "Imitation Is The Best Form Of Flattery"... Your idea to hack up a manifold and try something new got me thinking. The way my MG1/MG2 sits, I could never use the 1NZ-FE intake or even your 'Tooter manifold' - the throttle body would conflict with my inverter. But I was thinking of doing something with the 2AZFE intake manifold because the throttle body would come out the passenger side...problem is - the manifold is plastic.
Picture not included in this copy Not sure how I could 'weld' the 1NZ flange onto the 2AZFE plastic tubing :( I may just have to make/design my own. Luckily you already have the flange I need to weld onto! 👍
JustDidItUnited States · Mar 7, 2013#96 Originally Posted by
JustDidIt ↑ I've found a FULL 2012 Yaris 1NZ-FE cylinder head super cheap. Now just waiting to hear back if I can have it shipped or if I have to go pick it up.
For a decent EMS...Still haven't found much info on whether or not I can get by with the AEM F/IC or if I'll have to step all the way into the AEM EMS2 $$$$ :( Tuning is my biggest concern at this point. Just not looking to drop $2k just yet on EMS.
xnamerxxso cal · Mar 7, 2013#97Here is a comment from someone I know who used to tune cars for AEM, about using it for tuning my car.
the FIC was good, but i only used it on FI apps. in FI apps we only retard the timing, in your case i would imagine you want to increase the timing, which it cant do, can't predict the future, only delay it
tooterLos Angeles · Mar 7, 2013#98 Originally Posted by
JustDidIt ↑ If if you weren't the original.. "Imitation Is The Best Form Of Flattery"... Your idea to hack up a manifold and try something new got me thinking. The way my MG1/MG2 sits, I could never use the 1NZ-FE intake or even your 'Tooter manifold' - the throttle body would conflict with my inverter. But I was thinking of doing something with the 2AZFE intake manifold because the throttle body would come out the passenger side...problem is - the manifold is plastic.
Picture not included in this copy
Is this the layout of your engine? And if it is, is your intake at the front of the engine or behind it?
Picture not included in this copy Not sure how I could 'weld' the 1NZ flange onto the 2AZFE plastic tubing :(
I'm not sure, but I think that the plastic might have been ultrasonically welded. And that "snail" style manifold might still have clearance issues, but that could be easily determined simply by taking some measurements.
I may just have to make/design my own. Luckily you already have the flange I need to weld onto! 👍
No rpoblem. 🙂
I'll always be stocking them. Since the design is finalized they can be manufactured as needed.
BEEFnorth carolina · Mar 7, 2013#99I am not sure if garm commented earlier in this thread but you can get pistons from him in a variety of thicknesses (compression ratios) so the big reason to use the prius pistons would be to save money.
I can't remember exactly what he said he had but it seems like he had 9:1, 11:1 and a 12:1. I may be a bit off on that one but you could ask him directly.
JustDidItUnited States · Mar 7, 2013#100 Originally Posted by
BEEF ↑ I am not sure if garm commented earlier in this thread but you can get pistons from him in a variety of thicknesses (compression ratios) so the big reason to use the prius pistons would be to save money.
I can't remember exactly what he said he had but it seems like he had 9:1, 11:1 and a 12:1. I may be a bit off on that one but you could ask him directly.
Saving $$$ is the idea... otherwise your correct you can get Arias Pistons with the CR ratios of 9:1 - 14:1 for the 1NZ...
Basically I just need the Cams and Cam gear with EMS...and I can test out this "prius Pistons" theory - not only will I get a bump from swapping cams from 1NZ-FXE to 1NZ-FE (stock 78hp to 108hp) ..but I should get a small boost from the 10:5 to 11:1 CR increase. I am sourcing a full 1NZ head now.