Looking good! It's funny that we both ended up installing them on the same day 😁 Your drop actually looks about the same as the DF210's on my Hatchback... and the Axis wheels fit the car VERY Well 🎉Originally Posted by slvryarisJust finished my NF drop up yesterday with the 215/40/17 tires. There has been no rubbing at all with just me in it. Me and a friend installed them and if we didnt bs all day it probably would have took about an hour and a half. Chris the write up was very very very helpful and was crazy cause it was like word for word. Here is an after pic.
TANABE DF210 Spring Install [pics]
146 posts · 139,307 views · page 2 of 3
Replies continued
DF or NF for s sedan? 1st priority is ride. so which 1?
also with these springs, what tire/wheel setup is best for no rubbing even with 4 seats used (170lbs per person)?
also with these springs, what tire/wheel setup is best for no rubbing even with 4 seats used (170lbs per person)?
if the ride comfort is 1st priority, go with the NF's
Just finished my df install (well about an hr ago....) nothing like putting your yarr back together with a halogen lamp..
I'll snap some more pics tomorrow morning and post them.
I'll snap some more pics tomorrow morning and post them.
👍 👍 👍Originally Posted by vodkalushJust finished my df install (well about an hr ago....) nothing like putting your yarr back together with a halogen lamp..
I'll snap some more pics tomorrow morning and post them.
Pics of before and after (your ognna have to deal with my crappy after pics due to rain...)











^^^^^
lookin sharp dood, lookin sharp...🤘
lookin sharp dood, lookin sharp...🤘
thanks 👍
Vodkalush, how much harsher is the ride compared to stock?
it is a little rougher, but the handling improvement makes up for it.
and honeslty I dont notice all that much, as its alot more fun being able to take turns at 60+ 🙂
and honeslty I dont notice all that much, as its alot more fun being able to take turns at 60+ 🙂
Cool! I haven't been able to decide between the DF's or the NF's. I use the car to commute about 90 miles roundtrip 5 days a week. It's nearly all freeway driving though so maybe I won't notice too much either.Originally Posted by vodkalushit is a little rougher, but the handling improvement makes up for it.
and honeslty I dont notice all that much, as its alot more fun being able to take turns at 60+ 🙂
Thanks!
Originally Posted by vodkalushit is a little rougher, but the handling improvement makes up for it.
and honeslty I dont notice all that much, as its alot more fun being able to take turns at 60+ 🙂
im with vodka..the ride is rougher a bit..but it looks badass...
and making hard turns aint shyt either....
Yeah, I hear ya. The only thing I can't stand about my car is the fender gap.Originally Posted by FoEKuZim with vodka..the ride is rougher a bit..but it looks badass...
and making hard turns aint shyt either....
Originally Posted by LizardboyYeah, I hear ya. The only thing I can't stand about my car is the fender gap.
Fender Gap...It was the first thing that had to go...my two cents for you....it doesnt matter what you choose.. nf or df....as long as its dropped.
with the df's though, i have had to be EXTRA careful on dips..and actually have to pay CLOSE attention to the road when driving...
I have a 120 mile round trip, all highway, and its perfect. 🙂Originally Posted by LizardboyCool! I haven't been able to decide between the DF's or the NF's. I use the car to commute about 90 miles roundtrip 5 days a week. It's nearly all freeway driving though so maybe I won't notice too much either.
Thanks!
Go get a set, and install 'em yourself, its C-A-K-E! 👍


Dropping it is definitely my next upgrade. One way or the other. I got the windows tinted first(kept me alive in the Palm Springs heat of the summer), then got the air horns so I wouldn't be run out of my lane again! Now I just wanna lower it and I'll be good for a while. I'll probably just wait a while to upgrade the intake and exhaust.Originally Posted by FoEKuZFender Gap...It was the first thing that had to go...my two cents for you....it doesnt matter what you choose.. nf or df....as long as its dropped.
with the df's though, i have had to be EXTRA careful on dips..and actually have to pay CLOSE attention to the road when driving...
Fender gap SUCKS!!!
Alright! You guys sold me! I'll drop her with the DF's! They're cheaper anyways! 🙂 She's gonna be DANG sexy!!! I'll just have to be a little more careful when we take her camping the next time, driving in the dirt. LOL!Originally Posted by Chris07LBI have a 120 mile round trip, all highway, and its perfect. 🙂
Go get a set, and install 'em yourself, its C-A-K-E! 👍
Originally Posted by LizardboyAlright! You guys sold me! I'll drop her with the DF's! They're cheaper anyways! 🙂 She's gonna be DANG sexy!!! I'll just have to be a little more careful when we take her camping the next time, driving in the dirt. LOL!
good to hear....👏 🍻
One more question guys! When you put on your DF's did you upgrade your shocks? I thought I read a thread somewhere on here that with the DF's you should really upgrade the shocks since they would be compressed more than with the stock springs or even the NF springs.
Nope... Consult Tanabe for any questions you may have. Or ask Chris who has talked to them directly. They are cake to install and will save you some good money.
Will do. Thanks!Originally Posted by slvryarisNope... Consult Tanabe for any questions you may have. Or ask Chris who has talked to them directly. They are cake to install and will save you some good money.
I have the NF springs on mine and the stock shocks perform ok still. I am sure that it does cause some premature wear but not enough right off hand. My NF's feel like I am floating on a cloud. I would dare to say that my NF's feel better then the stock suspension.
Better than stock? That's sweet! I guess I'll take a chance with the DF's. I'm hoping that if they're too stiff for me I'll be able to sell them on Yarisworld or on Ebay if need be and downgrade to the NF's. I think it's time for me to MAN-UP!😆 I've got the tint that I can't see through at night and the horns that make grown men jump when I put them on blast! Might as well keep going! 😁Originally Posted by slvryarisI have the NF springs on mine and the stock shocks perform ok still. I am sure that it does cause some premature wear but not enough right off hand. My NF's feel like I am floating on a cloud. I would dare to say that my NF's feel better then the stock suspension.
it wont be too stiff, ecpically with the stock struts/springs. It works perfect with the stock components.
I on the other hand, would still like to get firmer shocks/struts and finish the rest of my suspension mods (sway & rear strut bar).
I on the other hand, would still like to get firmer shocks/struts and finish the rest of my suspension mods (sway & rear strut bar).
Originally Posted by Chris07LBit wont be too stiff, ecpically with the stock struts/springs. It works perfect with the stock components.
I on the other hand, would still like to get firmer shocks/struts and finish the rest of my suspension mods (sway & rear strut bar).
I installed my DF210 today. HOLY CRAP WHAT A DIFFERENCE!!! I swear they feel better than stock. I use this DIY a couple of times as a reference and couldn't be any better. I also installed a Tanabe Medallion exhaust and AEM CAI I will take pics tomorrow if I get my rims installed, so Thank You Chris07LB
🤘
Originally Posted by YamilRso Thank You Chris07LB
🤘
Welcome buddy! 👍
I bet she sounds mean with your intake / exhaust combo huh? 🤤
She does have a "pair" right nowOriginally Posted by Chris07LBWelcome buddy! 👍
I bet she sounds mean with your intake / exhaust combo huh? 🤤
just a update after i have had DF210's on my sedan for some time now.
definetly love the ride, and the handeling is wonderful, and the stance is very nice, would have liked the body to sit a little lower to the ground, but what are you going to do?
but the one issue i have had with them is that when i have someone in the back seat the tire deffinetly scrubbs on the plastic inside the wheel well, not a big enough issue for me to do any cutting, but it is deffinetly noticable, and sometimes scares people in the backseat...
but overall i would recomend DF's to anyone that asks me :)
definetly love the ride, and the handeling is wonderful, and the stance is very nice, would have liked the body to sit a little lower to the ground, but what are you going to do?
but the one issue i have had with them is that when i have someone in the back seat the tire deffinetly scrubbs on the plastic inside the wheel well, not a big enough issue for me to do any cutting, but it is deffinetly noticable, and sometimes scares people in the backseat...
but overall i would recomend DF's to anyone that asks me :)
I just got some Tanabe NF210 for my sedan and my friend and I have already installed the rears. We're having problems installing the front. I was wondering how tight the nut is on top the nut that is compressing the spring? We can't loosen it or nudge it. We're even tried holding it down with an allen but the nut still wont move. Any suggestions?
any feedback on the TRD or the Eibach springs compared to the above
I worked at the damn thing for prob 20mins... but then again I dont have the best tools and I was working with a spot light; If you where to take off all the plastic pieces around the windshield wipers I bet it wouldnt make things easier.
If I remember right Theres only 2 pieces plus the wipersOriginally Posted by vodkalushIf you where to take off all the plastic pieces around the windshield wipers I bet it wouldnt make things easier.
The TRD springs are nice... they aren't quite as low as, say, the NF's, but they still provide an ample drop. The shocks drastically change the handling. Say goodbye to any hopes of a smooth ride, say hello to cornering 90 degrees at 30-40 MPH. Fun stuff.
You do have the spring compressed right? If not, you NEED to compress the spring before removing the upper strut mount from the strut.Originally Posted by sillyyarisI just got some Tanabe NF210 for my sedan and my friend and I have already installed the rears. We're having problems installing the front. I was wondering how tight the nut is on top the nut that is compressing the spring? We can't loosen it or nudge it. We're even tried holding it down with an allen but the nut still wont move. Any suggestions?
Just remove the strut and spring together and take it to a NAPA or some other autoparts store that has a strut spring comperssor, or maybe a shop can do it for you. Either should charge you around $40 per strut to R&R the spring.
nice DIY 🙂
do you guys had to (partially) remove the etire wipper support to get access to the bolt on the shock tower ? (pic is for a hb canadian model)
do you guys had to (partially) remove the etire wipper support to get access to the bolt on the shock tower ? (pic is for a hb canadian model)

any idea how to remove this 17mm nut ? Can't put the 17mm socket and the allen key in the same time as the nut is "deep" 🤷

Look at my pictures again.. i didnt remove anything but the plastics out of the way, and a long 17mm box wrench and long allen fit just fine...
It is a bit of a pain to get the right angle, and bite, but after a bunch of baby step turns, its DOES go tight or loose all the way. 👍
It is a bit of a pain to get the right angle, and bite, but after a bunch of baby step turns, its DOES go tight or loose all the way. 👍
however the normal 17 box wrench doesn't fit down to the nut, as the nut sits deep down in the black metal part around it... dit you used a deep offset box wrench 🤷
Make sure you have your jack under the side you are working on, with some pressure on it. This will compress the spring/strut, and make removing the nut a lot easier.Originally Posted by hystria ↑however the normal 17 box wrench doesn't fit down to the nut, as the nut sits deep down in the black metal part around it... dit you used a deep offset box wrench 🤷
Look at my pictures, its a regular box wrench. Maybe take a trip to the store, and look for something thats better/deeper then what you're using. 🤷
thanks, indeed that whas too deep, dont know why but it was... even with the side completely jacked. finally I put a normal socket and grip it veeery solid with the wisegrip then turn it - that worked 🙂
just to help a bit, when removing the whipper arms, a nice idea is to tap on the bolt that retains the arm while pulling with the other hand on the arm - this should make it easy
just to help a bit, when removing the whipper arms, a nice idea is to tap on the bolt that retains the arm while pulling with the other hand on the arm - this should make it easy
planning on getting DF's for my S. i mainly use my car for transportation (freeway most of the time), so DF's would be a good choice, right? keep in mind, i do have 3 passengers with me at times with some luggage in the trunk.
ummm, after the springs got "warn-in" I seem to get some rubbing at times with a full trunk, crap in the back and front seat passanger.... but as long as I go over bumps slowly (say in and out of some parking lots, missing pot holes) everything seems fine for the most part.
Hey guys I just recently installed the nf's and they turned out great, handling is improved ride is just a tad stiffer than stock, and it looks 10 times better, and even better once i get some 17's on it. I had some things to add to the How to as well.......
Rear springs
1. Position the jackstands as posted in the picture and worked real well for me was positioning my jack underneath the center of the arm and jacking it up or down to my needs, rather than each side individually
2. Before undoing the shock bolts there is what looks to be a vacuum line bolted to the arm.....If you look at picture 7 you will see a black threaded stud next to aluminum looking clip, unbolt the vacuum line from the arm because the line will get real tight when you undo both shock bolts...
Front
1. Yes you can reach the top bolt with just undoing the trim and wiper blades.......but i undid that plus the motor and metal bracket that goes across the back side of the engine bay...free'd up a lot of room and made it very easy....
the back took 45 minutes which included opening up the springs and grabbing all the tools i needed, very simple.....
the front took a bit longer, always with a strut mounted spring. Once you get that first one done you know exactly what to do on the second one......
Chris07lb, if you want to add any of this to your tutorial by all means, and hope its ok i referenced to one of your pictures........the write up was great and helped me out.......
anyone in socal need any help whether its verbal or literally a hand, let me know.......
I will work for beer lol....
Rear springs
1. Position the jackstands as posted in the picture and worked real well for me was positioning my jack underneath the center of the arm and jacking it up or down to my needs, rather than each side individually
2. Before undoing the shock bolts there is what looks to be a vacuum line bolted to the arm.....If you look at picture 7 you will see a black threaded stud next to aluminum looking clip, unbolt the vacuum line from the arm because the line will get real tight when you undo both shock bolts...
Front
1. Yes you can reach the top bolt with just undoing the trim and wiper blades.......but i undid that plus the motor and metal bracket that goes across the back side of the engine bay...free'd up a lot of room and made it very easy....
the back took 45 minutes which included opening up the springs and grabbing all the tools i needed, very simple.....
the front took a bit longer, always with a strut mounted spring. Once you get that first one done you know exactly what to do on the second one......
Chris07lb, if you want to add any of this to your tutorial by all means, and hope its ok i referenced to one of your pictures........the write up was great and helped me out.......
anyone in socal need any help whether its verbal or literally a hand, let me know.......
I will work for beer lol....
Originally Posted by 07typeS ↑Hey guys I just recently installed the nf's and they turned out great, handling is improved ride is just a tad stiffer than stock, and it looks 10 times better, and even better once i get some 17's on it. I had some things to add to the How to as well.......
Rear springs
1. Position the jackstands as posted in the picture and worked real well for me was positioning my jack underneath the center of the arm and jacking it up or down to my needs, rather than each side individually
2. Before undoing the shock bolts there is what looks to be a vacuum line bolted to the arm.....If you look at picture 7 you will see a black threaded stud next to aluminum looking clip, unbolt the vacuum line from the arm because the line will get real tight when you undo both shock bolts...
Front
1. Yes you can reach the top bolt with just undoing the trim and wiper blades.......but i undid that plus the motor and metal bracket that goes across the back side of the engine bay...free'd up a lot of room and made it very easy....
the back took 45 minutes which included opening up the springs and grabbing all the tools i needed, very simple.....
the front took a bit longer, always with a strut mounted spring. Once you get that first one done you know exactly what to do on the second one......
Chris07lb, if you want to add any of this to your tutorial by all means, and hope its ok i referenced to one of your pictures........the write up was great and helped me out.......
anyone in socal need any help whether its verbal or literally a hand, let me know.......
I will work for beer lol....
I think that "line" is your ABS, and most of us do not have that, but good point either way.
Read your owners manual.. its is said to NEVER jack up the rear of the car, by the center of the beam, connecting both rear wheels.Originally Posted by 07typeS ↑
Rear springs
1. Position the jackstands as posted in the picture and worked real well for me was positioning my jack underneath the center of the arm and jacking it up or down to my needs, rather than each side individually
lol dude i put a block of wood across the whole arm, forgot to mention that.......that simulates what the car is doing on the ground so its no big deal........i can agree not to have all that stress on the center but i had it spread evenly.......
and thanks for the info nimble, yea i didnt remember seeing that step in the how to so i looked and saw that he didnt have the line but had the stud for it......
and thanks for the info nimble, yea i didnt remember seeing that step in the how to so i looked and saw that he didnt have the line but had the stud for it......
Do you think this would be possible without a spring compressor?
No. You have to use it to at least remove the old springs from the struts... not needed so much to re-install the shorter Tanabe springs.Originally Posted by OgDogg ↑Do you think this would be possible without a spring compressor?
You can rent one from your local parts store for 10 bucks. Do it the SAFE way, get a spring compressor.
Originally Posted by Chris07LB ↑No. You have to use it to at least remove the old springs from the struts... not needed so much to re-install the shorter Tanabe springs.
You can rent one from your local parts store for 10 bucks. Do it the SAFE way, get a spring compressor.
If you have air tools you can get the stock front springs off without a spring compressor. Have a friend secure the strut on the ground with his foot. Give yourself about 15-20 feet in case anything goes flying, and make sure no one is standing in front of the strut. Use an impact gun to remove the strut nut. The spring will pop off about a foot, and some of the little parts may scatter, just keep an eye on everything. I did mine this way and the nut rolled away. everything else was right there.
Use common sence and safety and you will be fine without a spring compressor. If you are stupid, using hand tools, or don't have the proper room to do this, get a spring compressor.
Ashley
$10 .vs. risking getting hurt. Your choice.Originally Posted by OgDogg ↑Do you think this would be possible without a spring compressor?